LED PANEL
Contents
1. LED 4TC Innovation Quality Performance f User Manual Please read the instructions carefully before use EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55103 1 199601 2 EN55103 2 1996 EN61000 3 2 2000 A2 2005 EN61000 3 3 1995 A1 2001 A2 2005 amp Harmonized Standard EN 60598 1 2004 IEC 60598 1 2003 corrigendum 2004 Part 1 General requirements and test Following the provisions of the low voltage directive 73 23 EEC and 93 68 EEC TABLE OF CONTENTS Safety Instructions Technical Specifications Installation How to set the unit How to control the fixture DMX512 Configuration DMX512 Connections Troubleshooting Fixture Cleaning Introductions A N Please read the instructions carefully which includes important WARNING information about the installation operation and maintenance Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the fixture Before operating ensure that the voltage and frequency of power supply match the power requirements of the fixture Its important to ground the yellow green conductor to eart2. particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 8 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A ils The fixture does not work no light Check the connection of power and main fuse Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX connectors cables to see if link properly If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal Wrong DMX address in the fixture Set the proper address No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tappi
3. return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are shown below Addr 5 z DMX512 Address Setting e C B i i nel sec k B Master Slave operation Lhiid AJ 3 Channel mode 3 The fixture will allow you to link 16 fixtures together and operate without a controller In nd H Channel mode 4 Master Slave mode the first fixture will control the others to give an automatic sound 2h O Auto Show activated synchronized light show This function is good when you want an instant show cnn aP i The first fixture its DMX input cable will have nothing connect it and the other fixtures will Show 1 12 be set in slave mode automatically Their DMX input cables connect the last fixture DMX cue Sr output cable daisy chain Any fixture can act as a Master or as a Slave Lh ce has Chase C Easy Controller by CA 8 Lh ib cp o The easy remote control is used only in master slave mode There is a A rade terminator for connect the easy controller inside the fixture By connecting the A n Master Mode cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the aLr Slave Mode 1 16 first fixture you will find that the remote control on the first fixture will control all 2L 16 the other fixtures for Stand by Function and Mode functions i Cin on sound Control ON off Sound Control OFF 6 Bl
4. ER button and the display will show the version of software of the unit To go back to the functions press the MENU button again 5 How to control the fixture There are three ways to control the fixture A Universal DMX controller B Master Slave operation C Easy controller oy CA 8 A Universal DMX controller The fixture can be set the DMX address remotely by universal DMX controller First you need to programming two scenes into a chase and then link the fixtures to the universal DMX controller When you run the chase all the fixtures of the chain will be set the series DMX address automatically The fixture uses four channels Please refer to the following diagram to set the address for the first four units 11 is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the OOC DMX 512 Address Setting Press the MENU button up to when the cdr js shown on the display Press ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once selected press the ENTER button to store or automatically return to the main functions without any changes after 8 seconds To go back to the functions without any change press the MENU button again ttt VL Channel mode Press the MENU button up to when the Lhi id is shown on the display Pressing the ENTER button and the display will blink Use t
5. ackout Mode No Blackout Blackout To blackout all the fixture tl MENU DLLO 40G Blackout Mode Yes Blackout Function Strobe Select Color Select show Select Chase m i 1 Synchronous strobe et in white color Color 1 16 or Show 1 12 Chase 1 16 or fade Color Macro 2 The same color chase manual setting Lolo fo i6 3 Different color strobe color g Red 0 255 Mode Sound 1 Manual Sound 2 Auto Ndaut Gr n Green 0 255 LED OFF LED ON LED slow blinking LED fast blinking bhla Blue O 255 Pg on LED on off LED off ai cp on Inversion oFF Normal Lene Temperature red D bola Uren i White Blance DLue g35 Fhe Fixture Hours ver Software Version 7 12 Loot o LIltl tt White balance Press the MENU button up to when the bole is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the ked red or or Pal green or bt uel blue press ENTER button to confirm then use DOWN and UP button to adjust the value 0 255 and press ENTER bution to store automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Vil Fixture Hours Press the MENU button up to when the functions press the MENU button again I D uel l Software version Press the MENU button up to when the is blinking on the display Pressing ENT
6. fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 4 How To Set The Unit Flashing Sound activation MENU To select the programming functions 7 DOWN To go backward in the selected functions UP To go forward in the selected functions 9 ENTER To confirm the selected functions 0 Microphone Receive music for the sound active Only for remote control By connect to the CA 8 or CA 9 RTX to control the unit for Stand by Function and Mode function 2 DMX output For DMX512 link use 3 5 pin XLR plug cable to link the next unit 3 DMX Input For DMX512 link use 3 5 pin XLR plug cable to input DMX signal 4 Mains input Connect to supply mains power Mains output Connect to supply mains power for the next unit 5 7 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels i ere COMMON een DMX f DMX OUTPUT S e CO Termination reduces signal errors and avoids signal transmission problems and interference Itis always G DN advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and XY pin3 DMX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of t
7. h in order to avoid electric shock Disconnect main power before servicing and maintenance Use safety chain when fixes this fixture Don t handle the fixture by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Do not connect the device to any dimmer pack Do not touch any wire during operation and there might be a hazard of electric shock To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture The housing must be replaced if they are visibly damaged Do not look directly at the LED light beam while the fixture is on Warning If using a 230Vac 50Hz power supply do not connect in series more than 30 units use another mains supply for the next 30 units If using a 120Vac 60Hz power supply do not connect in series more than 21 units use another mains supply for next 21 units 9 Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or
8. he DOWN and UP button to select the fid channel 1 or d channel 2 or fd 3 channel 3 or Ad 4 channel 4 mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again I I Show Mode Press the MENU button up to when the rit ig shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select theah ig show 8 5h i show 1 or Sih e show 2 or Sho auto show Once the show has been selected press the ENTER button to confirm if you select Im i show 1 or Sh _ show 2 or 94 i show 12 you can press DOWN and UP button to select SP slowest or SP gl fastest press ENTER button to store or automatically return to the main functions without any change after 8 seconds To go back to the functions or without any change press the MENU button again Chase Mode Press the MENU button up to when the Chas is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the Lh i chase 1 or or LA ID chase 16 or fade Once the chase has been selected press the ENTER button to confirm then press DOWN and UP button to select SP Li slowest 8 or SP gl fastest press ENTER button to store or automatically return to the ma
9. he next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 3 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 4 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 5 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 1 512 6 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pint GND Pin2 Negative signal Pin3 Positive signal 5 pin XLR Pint GND Pin2 Negative signal Pin3 Positive signal Pin4 5 Not Used 14 DMX512 Configuration Ch2 255 100 255 p100 248 2559 OPEN 201 247 191 200 255 100 255 i00 ow 0 13 255 o0 Color _ Macro 128 195 4 4 2 Main Function To select any of the given functions press the MENU button up to the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER buiton to setup or it will automatically
10. in functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Slave Mode Press the MENU button up to when the Suid is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the imk Z Mater or St i normal or or St I0 16 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Lew _ ILIT1 Sound control Press the MENU button up to when the Soun is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 2n sound control on or 2i sound control off Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Blackout Mode Press the MENU button up to when the E is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 02 no blackout or S25 yes blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functi
11. ng the microphone One of the channels is not working well The stepper motor might be damaged or the cable connected to the PCB is broken The motor s drive IC on the PCB might be out of condition 15 e To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture e Do not open the unit within five minutes after switching off e The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs yourself In the unlikely situation your unit may require service please contact your nearest dealer 2 Technical Specifications e DMX channel 4 channel modes e LED 4 x 3W RGB Tri color LED 50 000 hrs rated e Power supply Input Voltage AC 100 240V 50 60Hz e Power consumption 28 5W e Fuse T 6 3A e Dimension 218 x 186 x 89 mm e Weight 1 8 kgs mag Q ATONE T sak La I 3 Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the units weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be
12. nk Use DOWN and UP button to select the display inversion or S display normal Once select press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again a Fixture Temperature Press the MENU button up to when the Line is blinking on the display Pressing ENTER button and the display will show the temperature of the unit To go back to the functions press the MENU button again
13. ons without any change after 8 seconds To go back to the functions without any change press the MENU buiton again Color Mode Press the MENU button up to when the Colo is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the to I color 1 or or Co igl show 16 or manual setting Once select press the ENTER button to confirm if you select manual setting you can press DOWN and UP button to select ked red or or Pal green or bt uel blue press ENTER button to confirm then use DOWN and UP button to adjust the value 0 255 and press ENTER button to store automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Led Display Press the MENU button up to when the Led is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the _ Led on or Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again I C gi gP Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the LEd is shown on the display Pressing ENTER button and the display will bli
Download Pdf Manuals
Related Search