User Manual
Contents
1. EXT HDMI1 3 1410 BLK EXT HDMI1 3 1410 SIL User Manual Release A4 mi Distribution Gefen 1 10 Distribution Amplifier for 1 3 Important Safety Instructions 10 11 12 13 14 15 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install or place this product near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer To reduce the risk of electric shock and or damage to this product never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture Unplug th2. De Distribution Front Panel page 8 Operating the 1 10 Distribution Amplifier for HDMI 1 3 EDID Management Internal EDID Use this EDID mode if problems are encountered when using the external EDID The built in internal EDID provides the source device with a generic EDID which can be used by all display sink devices 1 Select the internal EDID mode Refer to Selecting the EDID Mode page 8 2 Press and release the Reset button on the front panel of the distribution amplifier to reset the unit The distribution amplifier must be reset or power cycled each time the EDID mode is switched The table below displays the video timings and audio formats supported by the internal EDID NOTE All sink devices connected to the distribution amplifier must be compatible with at least one resolution audio format specified in the internal EDID If one of the connected displays does not support xvYCC then this feature is removed from the EDID Video Timings Audio Formats 640 x 480p 59 60 4 3 LPCM 2CH 720 x 480p 59 60 4 3 720 x 480p 59 60 16 9 280 x 720p 59 60 16 9 920 x 1080i 59 60 16 9 440 x 480i 59 60 4 3 920 x 1080p 59 60 16 9 720 x 576p 50 4 3 720 x 576p 50 16 9 280 x 720p 50 16 9 920 x 1080i 50 16 9 440 x 576i 50 4 3 920 x 1080p 50 16 9 920 x 1080p 23 24 16 9 Native resolution page 9 Operating the 1 10 Distribution Amplifier for HDMI 1 3
3. This LED indicator will glow bright blue once an active source device is connected to the HDMI In connector This LED indicator glows bright red when the unit is powered page 2 Getting Started Name EDID Ext Int Out 1 10 24V DC Panel Layout Back E gt e gt u um Description Use this switch to have the 1 10 Distribution Amplifier for HDMI 1 3 use the internal EDID or external EDID See EDID Management page 8 for more information Use the included HDMI cable to connect the Hi Def Source to this port Connect up to 10 HDTV displays to these HDMI outputs Connect the included 24V DC power supply from this power receptacle to an available AC electrical outlet page 3 Installation Connecting the 1 10 Distribution Amplifier for HDMI 1 3 1 Connect the included HDMI cable between the Hi Def source and the In port on the distribution amplifier 2 Connect up to 10 Hi Def displays to the distribution amplifier using each of the Out ports 3 Connect the included 24V DC power supply from the power receptacle of the distribution amplifier to an available electrical outlet Sample Wiring Diagram ED Hi Def Source HDMI CABLE Splitter for HDMI PA Display YA HD Display S Display HD Display AG jw D pd EXT HDMI1 3 1410 BLK 2 2 Display p page 4 02 Operating the 1 10
4. EDID Management External EDID When set to Ext mode EDID data will be fetched from the sink that is connected to Out 1 It is recommended that the display with the lowest native resolution be connected to Out 1 This ensures that a compatible video signal will be output to all connected displays 1 Select the external EDID mode Refer to Selecting the EDID Mode page 8 2 Press and release the Reset button on the front panel of the distribution amplifier to reset the unit The distribution amplifier must be reset or power cycled each time the EDID mode is switched When the external EDID is used the following rules apply gt The 1 10 Distribution Amplifier for 1 3 will always attempt to read the EDID from the sink device connected to the Out 1 port and copy it to the In port Out 1 is the default primary output port gt sink device is not detected on the primary output port then the distribution amplifier will sequentially scan all subordinate output ports 2 3 etc until a sink device is found Once detected this subordinate output port will become the new primary output port and the EDID will be copied to the In port This state will be in effect until a sink device is connected to the Out 1 port and the distribution amplifier is power cycled or the Reset button is pressed gt EDID capabilities timings audio color depth etc will be supported by all subordinate sink devices only if they are support
5. Distribution Amplifier for HDMI 1 3 EDID Management B ONE INSOFERN IEEE 8 Selecting thes EDI DIM Od cee rr AAA PEDE 8 Internal DID ere 9 b Deere Ud HM UH E 10 Operating the 1 10 Distribution Amplifier for HDMI 1 3 EDID Management The 1 10 Distribution Amplifier for HDMI 1 3 features EDID Management Before the Source can send video and or audio to the display sink the source reads the EDID Extended Display Identification Data from the sink display devices that are connected to the distribution amplifier The EDID contains information about what type of audio video data that the source can send to each output device The distribution amplifier can use either the downstream EDID from the display sink or the built in internal EDID Selecting the EDID Mode 1 Use sharp pointed object such as a jeweler s screwdriver to slide the EDID switch to the desired position gt Setthe switch to the Int position shown below to use the built in internal EDID gt Setthe switch to the Ext position to use the external downstream 2 After the desired EDID mode is selected press the Reset button on the front panel The distribution amplifier must be reset or power cycled when switching between EDID modes 4 10 HOMI 1 3 Gefen Inc P s wu In Qut 1 Qut 2 Qut 3 Back Panel EDID Ext Int Reset button
6. acific Time 1 10 Distribution Amplifier for HDMI 1 3 is a trademark of Gefen LLC Important Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 2014 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners iv 1 10 Distribution Amplifier for 1 3 Operating Notes Make sure to connect all the cables and the power supply prior to connecting power to the HDMI sources and the 1 10 Distribution Amplifier for HDMI 1 3 3D content will be displayed when using with a 3D compatible source and TV The 1 10 Distribution Amplifier for HDMI 1 3 features an EDID selection that will allow the user to choose from external EDID from an attached display or a built in internal EDID See EDID Management page 8 for more details 1 10 Distribution Amplifier for 1 3 Features and Packing List Features Simultaneously displays a single Hi Def source on up to 10 HDTV displays without signal loss Maintains sharp HDTV resolutions up to 1080p Full HD and 2K HDMI Features gt 225 MHz up to 12 bit YUV 444 supported 1080 gt Deep Color gt Dolby TrueHD and DTS HD Master Audio P Lip Sync 3DTV Pass Through Color Space Conversion EDID Management for rapid integration of sources and display devices Mono LOK Locking HDMI Connectors Supports the use
7. ed by the primary sink device gt Operational compatibility issues may result if a subordinate sink device is unable to support the EDID capabilities of the primary sink device page 10 03 Appendix Specifications 14 Appendix Specifications Resolutions max 1080p Full HD 1920 x 1200 WUXGA 2K Maximum Pixel Clock 225 MHz Input Video Signal 1 2V p p Input DDC Signal 5V TTL Power Indicator 1 X LED red Activity Indicator 1 X LED blue EDID Switch 1 x Slide type Video Input 1 x HDMI Type A 19 pin female Video Output 10 x HDMI Type A 19 pin female 1 x 24V DC 17 x 1 75 x 5 5 432mm x 45mm x 140mm Dimensions W x H x D 1 8 lb 0 8 kg Unit Weight page 14 Stretch it Switch it Split it Gefen s got it 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com support gefen com us amp This product uses UL listed or CE compliant power supplies 40
8. is apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Batteries that may be included with this product and or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions 1 10 Distribution Amplifier for 1 3 Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular pur
9. of DVI sources and DVI displays with an HDMI to DVI converter cable or adapter Rack mountable rack ears included HDMI and HDCP compliant 23 1080 HDMI HDCP PROGRESSIVE Mia Ger man Mcr Mb reese COMPLIANT Packing List The 1 10 Distribution Amplifier for HDMI 1 3 ships with the items listed below If any of these items are not present in the box when you first open it immediately contact your dealer or Gefen 1 1 10 Distribution Amplifier for HDMI 1 3 1x6 ft HDMI cable 1 24 DC Power Supply 1 Setof Rack 1 x Guick Start Guide vi 1 10 Distribution Amplifier for 1 3 Table of Contents 01 02 03 Getting Started Connecting the 1 10 Distribution Amplifier for HDMI 1 3 Sample Wiring Diagram ior iter ee Operating the 1 10 Distribution Amplifier for HDMI 1 3 EDID Management een 8 Selecting irren te ti cete corre ne 8 Internal aaa 9 External EDID a sea 10 Appendix iia 14 viii 01 Getting Started Installation Connecting the 1 10 Distribution Amplifier for HDMI 1 3 TAS SampleWiringilbiagramis AAA AA AA AAA Getting Started Panel Layout Front EXT HDMI1 3 1410 SIL shown FACIT distribution Press this button to reset the 1 10 Distribution Amplifier for HDMI 1 3
10. pose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty Customers outside the US are responsible for shipping charges to and from Gefen Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 1 10 Distribution Amplifier for 1 3 Contacting Gefen Technical Support Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 Telephone Fax Email Visit us on the Web Technical Support Hours 818 772 9100 800 545 6900 818 772 9120 support gefen com www gefen com 8 00 AM to 5 00 PM Monday Friday P
Download Pdf Manuals
Related Search