8x8 Cat 5 A/V Matrix Switch VM0808T User Manual
Contents
1. VMO808T User Manual Installation Diagram B Audio Video Source x 8 a VE500T x 8 HEH HEHE VMO808T VE500R VE500RQ x 8 Display x 8 NO y JO 14 Chapter 3 Local Operation Overview The VMO808T can be configured and operated locally via the front panel pushbuttons or remotely over a standard TCP IP connection via a Browser graphical user interface GUI Local front panel operation is discussed in this chapter Over IP and Telnet operation is discussed in Chapter 4 Remote Operation Note 1 The VMO808T can also be controlled locally via a serial controller 2 See RS 232 Serial Interface page 41 for RS 232 serial commands Front Panel Operation The VMO808T features front panel pushbuttons and an LCD display panel for convenient configuration and operation at the local site This allows you to perform operations such as selecting which source displays on which display configuring the IP port and serial port adjusting audio and video levels and setting security information Basic Navigation Please note the following operation conventions Use the MENU pushbutton to cycle through the Main Menu options Use the AUDIO pushbutton to go directly to the independent audio page Us2. Note This option controls how long an inactive Web connection stays logged in to the VMO808T Any changes will take effect immediately Telnet Configuration Enable the checkbox if you want the VMO808T to receive commands on Port 23 for telnet use See Telnet Operation page 38 for further details Note The VMO808T must be power cycled for a change in the Telnet configuration block to take effect Serial Setup The Serial Setup settings enable you to configure the VMOSOST s serial connection Use the drop down menus to select values and then click Save or Clear Click Default Setting to use the following defaults Serial Port Address 0 Baud Rate 19200 Serial Port Mode RS 232 Note Mode options are RS 232 RS 422 RS 485 and bypass See Serial Port Mode page 24 for further details about bypass mode 34 Chapter 4 Remote Operation Port Name The Port Name page enables Administrators and Super Users to change the display name of the input and output ports Local Port_In_0 1 Port_In_1 12 13 Max 16 characters only 0 Input Num Input Name Port_In_2 Port_In_3 Port_In_4 Port_In_5 Port_In_6 Port_In_7 Port_In_8 fal S o S Y o S a El o S 0 o ggi 4 QO 0 o o jo gaad 3 Clear BEBE Clear 4 Num A port_out_o Port_Out_1 Port_Out_2 Port_Out_3 Port_Out_4 Port_Out_5 Port_Out_6 Po
3. The VMO808T s default IP address is http 192 168 0 60 See Web Setup page 34 for further information The default username and password are administrator password See Password page 37 for further information The same user cannot be logged in simultaneously Note The VMO808T login supports lower case letters only 29 VMO808T User Manual Connections Page The VMO808T s GUI main page is the Connections page This displays all active connections for control and configuration sauvon ETI ns i T oy coo 30 Chapter 4 Remote Operation Toolbar Icon Description Connections This page displays the VMO808T s active connections and enables you to control them This page enables you to configure the VMO0808T s IP settings and name ports User Management ia u This page enables you to configure user permissions including passwords Firmware mr The page enables you to upgrade the VMO808T s firmware gt a Help and Exit The first icon displays the VMO808T s help files The second icon ends the session and closes the Web interface Configuring Connections To configure a connection do the following 1 Select the radio button at the corresponding input output intersection of the port s you want to configure Note Multiple connections can be changed simultaneously simply select all t
4. 2 If bypass is selected the female RS 232 port connected to the local controller PC bypasses signals to the Receiver unit and RS 232 signals from the Transmitter unit pass to the male RS 232 port Select bypass if you are using the male RS 232 port to connect a serial device such as a touchscreen or barcode scanner Default Serial Settings To use not use the VM0808T s Default Serial Settings do the following 1 Select Default Serial Settings from the Set IP Port submenu The cursor flashes on the entry 2 Select Yes or No 24 Chapter 3 Local Operation Adjust Video Video Gain and Video Compensation can be adjusted for all displays at once or for each display individually To adjust video do the following 1 Use the MENU button to access the Adjust Video page E Adjust Video Level A MENU Ne Adjust Audio Level v awo CEN LS vue 2 With the cursor flashing at Adjust Video Level press Enter to go to the Optimize Video Output Port page to select ports gt Optimize Video Output Port MENU 3 Use the Up Down pushbuttons to cycle through the ports and select for optimization You are able to select all ports in the installation ALL just the local port L or any of the 8 ports individually 1 8 Press Enter to select 4 Select Gain or Compensation then cycle through the options to adjust values for the local port s MENU Esc Local Video Output Gain 31 XA
5. C Humidity 0 80 RH Non condensing Physical Housing Metal Properties Weight 3 50 kg Dimensions L x W x H 43 20 x 25 30 x 4 40 cm Carton Lot 1 pc 53 VMO808T User Manual Note 1 Depends on the connected receiver 2 The maximum transmission distance between the transmitter and the receiver is 300 m 54 Appendix Troubleshooting Symptom Possible Cause Action Audio cannot be controlled or adjusted RS 232 and video signals are switched to different channels Switch the video audio and RS 232 signals to the same channel and then the volume can be adjusted OR Manually adjust the audio on the connected audio devices e g amplifier 55 VMO808T User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquiries please co
6. and 2 Microsoft 64 bit ODBC and OLEDB driver 41 VMO808T User Manual Switch Port Commands The formulas for Switch Port commands are as follows 1 Switch Command Input Command Port number Output Command Port Number Address Device Number Control Enter For example to switch input port 02 audio and video to output port 05 on device 01 type the following sw i02 005 a01 Enter 2 Switch Command Output Command Port Number Address Device Number Control Enter For example to turn off video output on port 03 type the following sw 003 a00 video off Enter 3 Switch Command Output Command Port Number Address Device Number Control Enter For example to switch the next output to the local port type the following sw 11 a00 Enter Possible Values The following table shows the possible values for switch commands Command Description SW Switch command Input Command Description Input command Input Port Number Description xx 01 08 port default is 01 11 Local input port Output Command Description o Output command Output Port Number Description yy 01 08 port default is 01 11 Local output port All output ports 42 5 RS 232 Commands Address Description a Device address Device Number
7. configuration and operation via an intuitive Graphical User Interface GUD accessed via web browser as well as locally via front panel pushbuttons and LCD display The VMO808T can also be accessed via a remote terminal session using Telnet Furthermore for complete system and install integration serial control is standard through the VMO808T s built in RS 232 and RS 485 422 ports that allows the switch to be controlled through a high end controller or PC The unit s bi directional RS 232 serial port also allows serial devices such as touchscreens and barcode scanners to be included in the installation In combination with the ATEN VE500 A V Over Cat 5 Extender system the VMO808T 8x8 Cat5 A V Matrix Switch supports distances up to 300 meters between the transmitter and receiver units making it the ideal solution for applications that require A V serial information from multiple sources to be conveniently delivered to any of multiple destinations VMO808T User Manual Features Connects any of 8 Cat 5 A V inputs to any of 8 Cat 5 A V outputs in combination with ATEN VE300 or VE500 A V Over Cat 5 Extender system Long signal range supports up to 300 meters between VE300T or VESOOT transmitters and VE300R VE300RQ or VESOOR VESOORO receivers Easily switch between multiple sources and multiple displays Local Operation Front panel LCD display and pushbuttons Serial controller Remote Operation
8. page 15 Note The MENU and AUDIO front panel pushbuttons have built in LEDs that light to indicate they have been selected VMO808T User Manual Rear View 1 23 4 5 6 7 el ED a gt Ex III OOOO T 8 9 10 11 12 No Component Description 1 Power Socket This is a standard 3 pin AC power socket The power cord from an AC source plugs in here 2 Power Switch This is a standard rocker switch that powers the unit on and off 3 Grounding Terminal The grounding wire attaches here See Grounding page 9 for further details 4 Local Stereo Audio These ports are for the local stereo audio source and In Out Ports speakers 5 Local Balanced Audio These ports are for the local balanced audio source In Out Ports and speakers 6 RS 485 RS 422 These serial ports comprising of one 5 pole captive Serial Port screw connector RS 485 RS 422 and one DB 9 F RS 232 are for serial control of the VMO808T 7 RS 232 Serial Control Port Female Please download the appropriate software AP from our website www aten com and reference the Browser GUI chapter for operation See p 29 8 Local Video In Out These VGA ports are for connecting your local input Ports source and your local display 9 RS 232 Serial RS 232 serial devices such as touchscreens and Channel Port Male barcode scanners plug into this p
9. 1 Command Output Number Address Number Control Enter For example to optimize video quality for output port 02 on device 01 type the following video 002 a01 optimize Enter The following tables show the possiblee values for commands Command Description video video quality adjustment Output Command Description o Output command Output Port Number Description yy 01 08 port default is 01 11 Local output port i All output ports Address Description a Device address Device Number Description zz 00 15 default is 00 i All devices Control Description optimize Adjust video gain and video compensation for selected displays 46 5 RS 232 Commands Adjust Audio Commands The formula for Adjust Audio commands is as follows 1 Command Output Number Control Enter For example to adjust the audio volume for output port 02 to level 11 type the following volume 002 v11 Enter The following tables show the possiblee values for commands Command Description volume adjust audio level volume Output Command Description o Output command Output Port Number Description yy 01 08 port default is 01 11 Local output port x All output ports Address Description a Device address Device Number Description zz 00 15 defa
10. Aa Baa ede ii SIT 11364 gt 2006 4 2 2 2 2 o HA ie aed ii User Information vicio er ne ae ada ee are ee iii Online Registration 00 00 0 c eee iii Telephone Support 000 0c cee eee iii User Not sache iii Package ContentS o oocooccccooooc eee iv Contents a oi eta erat dado oh sade oh ves v About this Manual ooooccccoccc nennen viii Conventions s u van need He a teas Bee die ested ee te oe ix Product Informations ssr 200 ae a 2 22242 ee see ix Chapter 1 Introduction OVER o la 1 Features er we eee Det 2 Requirements Gane st de 3 Transmitters ohh bite kee pects Abed ee bd bbe dh Deed od 3 RECEIVERS smee a da een Se Pace an acted ected re 3 Local Input Outputs oe to pete ee ety ee eel nr wots a oe 3 G bles u scent hei eet e EA bec ee Re eases PRS 3 Source Device Operating Systems 0 00 0 eee eee eee 4 COMPONEN S siea er een ee a cee es ti 5 Front VIEW 23 25 ta yes Gone Ronee wee eee Pe 5 Rear View i nepa an a dents Bea 6 Chapter 2 Hardware Setup Rack Mounting s cai a ar ee a 7 Grounding ta A na A TE Pt 9 Cable Connection dt npma nennen eee 11 Installation Diagram A 222 oe tee 13 Installation Diagram BB 2222 nsee rennen rennen 14 Chapter 3 Local Operation OvervieWer ee a ee ee elek Horn 15 Front Panel Operation irs errea piner aa E E nenn 15 Basic Navigation 0 noses ei Enee o a E tenes 15 Menu Organization so
11. Local Video Output Compensation 31 ano ON Pers Options are Stored Auto or 0 31 See page 27 for storing values Note If either Gain or Compensation is set to Auto the other will also set to Auto automatically 25 VMO808T User Manual Adjust Audio The audio level volume can be adjusted for all sources at once or for each source individually To adjust audio do the following 1 Use the MENU button to access the Adjust Video page Adjust Video Level Adjust Audio Level 2 With the cursor flashing at Adjust Audio Level press Enter to go to the Adjust Audio Level page to select ports p gt Output Audio Port A ie DEN Audio Level 10 v awo CN E ti 3 Use the Up Down pushbuttons to cycle through the ports and select for adjustment You are able to select all ports in the installation ALL just the local port L or any of the 8 ports individually 1 8 Press Enter to select The cursor will move down to Audio Level 4 Then use the Up Down pushbuttons to cycle through the Audio Levels 0 15 and press Enter to select Note 1 The default audio level is 10 0dB 2 Audio level L R 00 mute 01 25dB 15 6dB 3 Independent audio cannot be adjusted See Troubleshooting page 55 26 Chapter 3 Local Operation Save Load Profile The VMO80ST allows you to store up to 16 numbered 0 15 different connection profiles that can be saved and recalled late
12. and stable before extending a device from the rack Use caution when pressing the device rail release latches and sliding a device into or out of a rack the slide rails can pinch your fingers After a device is inserted into the rack carefully extend the rail into a locking position and then slide the device into the rack Do not overload the AC supply branch circuit that provides power to the rack The total rack load should not exceed 80 percent of the branch circuit rating Make sure that all equipment used on the rack including power strips and other electrical connectors is properly grounded Ensure that proper airflow is provided to devices in the rack Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer Do not step on or stand on any device when servicing other devices in a rack 51 VMO808T User Manual Technical Support International For online technical support including troubleshooting documentation and software updates http eservice aten com For telephone support see Telephone Support page iii North America Email Support support aten usa com Online Troubleshooting http www aten usa com support Technical Documentation Support Software Updates Telephone Support 1 888 999 ATEN ext 4988 When you contact us please have the following in
13. and telephone numbers International http www aten com North America http www aten usa com VMO808T User Manual This Page Intentionally Left Blank Chapter 1 Introduction Overview The ATEN VanCryst VMO0808T 8x8 Cat5 A V Matrix Switch is a versatile audio video over Cat 5 serial solution that offers an easy and affordable way to route any of 8 audio video sources to any of 8 displays in combination with the ATEN VE500 A V Over Cat 5 Extender system With eight Cat 5 A V input ports the VMO808T allows you to connect eight source devices via eight VE300T VESOOT transmitters to eight monitors displays or projectors via eight VE300R VE300RQ VESOOR VESOORQ receivers at the same time In addition to the eight Cat 5 connections the unit is also enabled with local audio video inputs outputs so that an extra source device and monitor located in the same rack as the VMO808T can function as a further transmitter and receiver As a Matrix Switch each input can be independently connected to any or all outputs and the audio and video inputs from each source device can also be switched independently giving you the ultimate in flexibility and control in any multi display audio video installation While the A V signal travels over Cat 5 cable the VMO808T unit can be controlled over a standard TCP IP connection and so it will seamlessly integrate with your existing network infrastructure It allows convenient
14. that the sides of the RJ 45 connector make tight contact with the grounding contacts on the sides of the RJ 45 socket as shown in the diagram below Chapter 2 Hardware Setup Cable Connection Note A complete VM0808T installation requires additional transmitter and receiver units that are not included in the VMO808T package Compatible models are the VE300T or VESOOT Transmitter and the VE300R VE300RQ or VESOOR VESOORQ Receiver See Requirements page 3 for details Installation of the VMO808T is simply a matter of connecting the appropriate cables Refer to the installation diagrams on the following pages the numbers in the diagrams correspond to the steps below and do the following 1 Use a VGA Audio cable to connect the audio video output ports of the local computer or other audio video source to the VMO808T s Video In port and stereo balanced Audio In ports 2 Plug the local display s VGA cable into the VM0808T s Video Out port 3 Plug the local stereo balanced audio speakers into the appropriate Audio Out ports Note If both audio sources are connected the stereo audio source has priority 4 If you are using the serial control function use an appropriate serial cable to connect the computer or serial controller to the VMO808T s female RS 232 port or the RS 485 RS 422 captive screw connector Note See Serial Port Mode page 24 for further details a
15. 255 255 255 0 Gateway To set the VM0808T s Gateway do the following 1 Select Gateway from the Set IP Port submenu The cursor flashes on the first number gt Gateway 192 168 0 1 A MENU Sie Default IP Setting No y ne Ze 2 Use the Up Down navigation pushbuttons to select each number 3 Use the Left Right navigation pushbuttons to move the cursor forwards backwards 4 Press ENTER to confirm the Gateway Note The default Gateway is 192 168 0 1 21 VMO808T User Manual Default IP Settings To use not use the VMO808T s Default IP Settings do the following 1 Select Default IP Settings from the Set IP Port submenu The cursor flashes on the entry Gateway 192 168 0 1 Default IP seting No 2 Select Yes or No Save and Reset Exit After each operation you can either Save and Reset the Device to save all changes and restart the VMO808T Exit without Save to ignore changes and return to the Menu or Press ESC to return to the previous step without change 22 Chapter 3 Local Operation Set Serial Port To configure the VMO0808T s serial settings select Set Serial Port from the Menu Set IP Port ry a Set Serial Port y wo IN The sub menu provides four options Serial Port Address Baud Rate Serial Port Mode and Default Serial Settings as follows Serial Port Address To set the VMO808T s serial port address do t
16. ATEN 8x8 Cat 5 A V Matrix Switch VMO808T User Manual www aten com VMO808T User Manual FCC CE Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment CE Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures RoHS This product is RoHS compliant Safety This product has been classified as Information Technology Equipment SJ T 11364 2006 The following contains information that relates to China ABASORALR va BEEE x ame same sam EA acia O a BLASER oO 101 o O
17. Browser Graphical User Interface GUI Telnet Supports additional local input and local display provides an extra input output source Built in bi directional RS 232 serial port for high end system control Supports high resolution video up to 1920 x 1200 60Hz DDC2B Supports stereo and balanced audio Automatic and adjustable video and audio quality Independent switching of audio and video sources any audio source can be connected to any video source for output flexibility Upgradeable firmware Rack Mountable Note The VMO0808T AP and GUI operation instructions can be downloaded from the ATEN website www aten com Chapter 1 Introduction Requirements The following equipment is required for a complete VMO0808T installation Transmitters 8x VE300T or VESOOT Transmitters Receivers 8x VE300R VE300RQ or VESOOR VESOORQ Receivers Note For further information about the ATEN VE300 and VE500 A V Over Cat 5 Extender systems please visit the ATEN website or contact your ATEN dealer Local Input Output A VGA SVGA XGA SXGA UXGA WUXGA or multisync display device with an HDB 15 connector Computer or A V source device with VGA and stereo balanced audio output Stereo and or balanced audio speakers Cables Use VGA Audio RS 232 cables to connect the local computer or other audio video source device to the VM0808T Use cat 5e cables to connect the
18. Description Zz 00 15 default is 00 i All devices Control Description on Turn on off Turn off Next port Previous port video Switch video only skip audio ae ho Enter Description Enter Enter and send out the command Acknowledge Description Command OK Command is correct and the function is executed Command Incorrect Unavailable command or parameters Note 1 Each command string can be separated with a space 2 Some commands can be skipped and the default value will be used 3 The Audio or Video command string can be skipped and both values will be used 43 VMO808T User Manual Mute Commands The formulas for Mute commands are as follows 1 Mute Command Output Command Port Number Address Device Number Control Enter For example to mute output port 05 on device 01 type the following mute 005 a01 on Enter 2 Mute Command Output Command Port Number Address Device Number Control Enter For example turn on audio at output port 05 on device 01 type the following mute 005 a01 off Enter The following tables show the possible values for commands Command Description mute Mute selected output port Output Command Description o Output command Output Port Number Description yy 01 08 port 11 Lo
19. O O RIVAS E DEA AAA DEAR EEST 11363 2006M EN RBEKZ To O ZTFERENRRER BRASA EMREDER R HRMEA PNA SMM SIT 11363 2006K RE x RIVAS AE DRA OR MRE ee HSJ T 11363 2006HREER e VMO808T User Manual User Information Online Registration Be sure to register your product at our online support center International http eservice aten com Telephone Support For telephone support call this number International 886 2 8692 6959 China 86 10 5255 0110 Japan 81 3 5615 5811 Korea 82 2 467 6789 North America 1 888 999 ATEN ext 4988 United Kingdom 44 8 448 1 58923 User Notice All information documentation and specifications contained in this manual are subject to change without prior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or T
20. S Switch input to specified output SS 01 03 Switch input 01 to output 03 00 Local Port 11 SV Save the current connections into profile SV 01 Save the current connections into profile 01 12 TI Set timeout TI 30 Set 30 minute timeout 13 VR Software version information VR Software version 1 0 Note For further information about these functions please reference the equivalent Browser GUI functions earlier in this chapter 40 Chapter 5 RS 232 Commands RS 232 Serial Interface The VM0808T s built in bi directional RS 232 serial interface allows system control through a high end controller PC and or home automation home theater software package Configuring the Serial Port The controller s serial port should be configured as follows Baud Rate 19200 Data Bits 8 Parity None Stop Bits 1 Flow Control None RS 232 Control Tool RS 232 serial operations in a VMOS08T installation can be managed via a Graphical User Interface GUI on systems that are running Windows In order to use this Control Tool two separate items of software must be installed on all of the PCs in your installation NET Framework 2 0 and the Control Tool AP Please download the VM0808T RS 232 Control Tool AP and user instructions from the ATEN website www aten com Note For Windows 7 64 bit systems the following must be installed first 1 Microsoft Office 64 bit Access Database software
21. V interference caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE VMO808T User Manual Package Contents The VMO0808T package consists of 1 VMO808T 8x8 Cat 5 A V Matrix Switch 1 Power Cord 1 Rack Mount Kit 3 Terminal Blocks 1 User Instructions Check to make sure that all the components are present and that nothing got damaged in shipping If you encounter a problem contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and or any of the devices connected to it Features may have been added to the VMO808T since this manual was published Please visit our website to download the most up to date version O Copyright 2010 2015 ATENO International Co Ltd Manual Part No PAPE 0330 AT2G Manual Date 2015 06 29 ATEN and the ATEN logo are registered trademarks of ATEN International Co Ltd All rights reserved All other brand names and trademarks are the registered property of their respective owners VMO808T User Manual Contents FCG CE INTO Mal ica a ii Safety ins ira edhe ede odd de n E EE ae se E o a
22. VE300T VESOOT Transmitters and VE300R RQ or VESOOR RQ Receivers to the VM0808T Note Cables are not provided in the VMO808T package VMO808T User Manual Source Device Operating Systems Supported operating systems are shown in the table below OS Version Windows 2000 and higher Linux RedHat 6 0 and higher SuSE 8 2 and higher Mandriva Mandrake 9 0 and higher UNIX AIX 4 3 and higher FreeBSD 3 51 and higher Sun Solaris 8 and higher Novell Netware 5 0 and higher Mac OS 9 and higher DOS 6 2 and higher Note For Windows 7 64 bit systems the following must be installed first 1 Microsoft Office 64 bit Access Database software and 2 Microsoft 64 bit ODBC and OLEDB driver Chapter 1 Introduction Components Front View No Component Description 1 LCD Display The LCD display shows the various options for configuring and operating the VMO808T For full details see Front Panel Operation page 15 2 Front Panel Use the pushbuttons to navigate the LCD display to Pushbuttons configure and operate the VMO808T MENU Press to invoke the Main Menu AUDIO Press to invoke the Audio page ESC Press to cancel the current selection ENTER Press to confirm the current selection Use the directional pushbuttons to navigate up down left and right within the LCD display For full details see Front Panel Operation
23. ables Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock Do not attempt to service the device yourself Refer all servicing to qualified service personnel If the following conditions occur unplug the device from the wall outlet and bring it to qualified service personnel for repair The power cord or plug has become damaged or frayed Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair 50 Appendix Rack Mounting Before working on the rack make sure that the stabilizers are secured to the rack extended to the floor and that the full weight of the rack rests on the floor Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack Always load the rack from the bottom up and load the heaviest item in the rack first Make sure that the rack is level
24. bout the serial control options 5 If you are using a serial device at the local site connect it to the VMO808T s male RS 232 port 6 Plug a Cat 5e cable from the LAN into the VMO0808T s Ethernet port 7 Use a grounding wire to ground the unit by connecting one end of the wire to the grounding terminal and the other end to a suitable grounded object Note Do not omit this step Proper grounding helps to prevent damage to the unit from surges or static electricity See Grounding page 9 Continues on next page VMO808T User Manual 8 Connect up to 8 audio video sources to up to 8 Transmitter units 9 Using Cat 5e cable connect the Transmitter s Remote I O ports to the RJ 45 Cat 5 Input ports on the VMO808T 10 Connect up to 8 display devices and speakers to up to 8 Receiver units 11 Using Cat 5e cable connect the Receiver s Remote I O ports to the RJ 45 Cat 5 Output ports on the VMO0808T Note See the VE300 or VE500 A V Over Cat 5 Extender User Guides for further details of Transmitter Receiver installation 12 Plug the power cord supplied with the package into the VMO80ST s 3 prong AC socket and then into an AC power source 13 Power on the VMO808T and all devices in the installation Chapter 2 Hardware Setup Installation Diagram A Ld J Si AR CO b FX FL
25. cal output port All output ports default Address Description a Device Serial Port address Device Number Description zz 00 15 default is 00 All devices Control Description on Mute on audio from selected output port is disabled off Mute off audio output enabled default Note Each command string can be separated with a space 44 5 RS 232 Commands Save Load Profile Commands The formulas for Save Load Profile commands are as follows 1 Command Profile Number Address Number Control Enter For example to save the current connection configuration to profile 12 on device 01 type the following profile f 12 a01 save Enter 2 Command Profile Number Address Number Control Enter For example to load profile 12 on device 01 type the following profile f 12 a01 load Enter The following tables show the possiblee values for commands Command Description profile Save Load profile Profile Description f Profile Profile Number Description yy 00 15 default is 00 peice Description Number p Zz 00 15 default is 00 y All devices Address Description a Device address Control Description save Save the current connection configuration load Load a saved profile 45 VMO808T User Manual Adjust Video Quality Commands The formula for Adjust Video Quality commands is as follows
26. d Local Operation explains the fundamental concepts involved in operating the VMO808T at the local site via the front panel LCD display and pushbuttons Remote Operation provides a complete description of the VMO808T s Browser Graphical User Interface GUI and how to use it to remotely configure and operate the VMO808T RS 232 Commands provides information about system control using the VMO808T s built in bi directional RS 232 serial interface An Appendix provides specifications and other technical information regarding the VMOSOST viii VMO808T User Manual Conventions This manual uses the following conventions Monospaced A Indicates text that you should key in Indicates keys you should press For example Enter means to press the Enter key If keys need to be chorded they appear together in the same bracket with a plus sign between them Ctri Alt Numbered lists represent procedures with sequential steps Bullet lists provide information but do not involve sequential steps Indicates selecting the option on a menu or dialog box for example that comes next For example Start gt Run means to open the Start menu and then select Aun Indicates critical information Product Information For information about all ATEN products and how they can help you connect without limits visit ATEN on the Web or contact an ATEN Authorized Reseller Visit ATEN on the Web for a list of locations
27. de page 28 when the password screen is accessed the cursor flashes on the first digit Enter a 4 digit password to continue to the Main Screen Note If you are accessing the VMO808T for the first time the default password is 1234 E Enter Password gi 0 0 caw EZ NN Incorrect Password AUDIO GaN LY ENTER To enter a password do the following 1 Use the front panel Left Right pushbuttons to move the cursor 2 Use the front panel Up Down pushbuttons to cycle through the numbers 3 Press and Release Enter to confirm the password and continue to the Main Screen Note 1 If you enter an incorrect password re enter the correct password over the incorrect string 2 If Password Required see Security Mode page 28 is enabled the timeout is 5 minutes VMO808T User Manual Main Page The Main Page displays Output Ports 1 8 and Local in sequential order across the top Whichever source is displaying on each output port is shown directly beneath From the Main Page you can set create input output connections that route all signals from a selected input port to a selected output port You can also Press the Audio pushbutton to go straight to the independent audio setup page press the Menu pushbutton to continue cycling through the menu options or press the Esc pushbutton to exit the display Video In Selection To select which input source displays on each output port do the following 1 Use the navigati
28. e liquid or aerosol cleaners Use a damp cloth for cleaning The device should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company The device is designed for IT power distribution systems with 230V phase to phase voltage To prevent damage to your installation it is important that all devices are properly grounded The device is equipped with a 3 wire grounding type plug This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not attempt to defeat the purpose of the grounding type plug Always follow your local national wiring codes Do not allow anything to rest on the power cord or cables Route the power cord and cables so that they cannot be stepped on or tripped over 49 VMO808T User Manual If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or un interruptible power supply UPS Position system cables and power cables carefully Be sure that nothing rests on any c
29. e the ESC pushbutton to go back a level return to the Main page or exit Use the ENTER pushbutton to select options and confirm operations Use the Up Down navigation pushbuttons to cycle forwards or backwards through numbered options Use the Up Down Left Right navigation pushbuttons to position the cursor on options for selection VMO808T User Manual Menu Organization Use the MENU pushbutton to cycle through the main menu options starting from the Password page in the order show in the table below Menu Page Sub Menu Page s Password Main Page Select Video IN Independent Audio Page Select Independent Audio IN Set IP Port IP Address Save and Reset Exit Subnet Mask Gateway Default IP Settings Yes No Set Serial Port Serial Port Address Save Exit Baud Rate Serial Port Mode RS 232 RS 422 RS 485 Bypass Default Serial Setting Yes No Adjust Video Level Optimize Video Output All Local 1 8 Local Gain Pon Local Compensation Adjust Audio Level Output Audio Port All Local 1 8 Audio Level Stored Values 0 15 Save Load Profile Save to a Profile 0 15 Call a Saved Profile Security Mode Password Required Yes No Change Password Old New 16 Chapter 3 Local Operation Enter Password If the VMO808T has been configured to require a password for local operation see Security Mo
30. ei tiie s taie cti aendre enra ta apiha 16 Enter Password een ee se en ae sc eee bey a 17 Main Pages 2 22 ee Ea ee es 18 Video In Selection 0 000000 eee 18 Independent Audio In Selection 0 0000 e eee eee 19 VMO808T User Manual Set IP Poio he 242 MG OE ce Mew eee ee id 20 IPAddress pasate done oes dig nea els Seley Mews Wie Beds t 20 SUBNEUMASK u ne ee een sede Pa 21 Gateway ne Br re ie werkt 21 Default IP Settings 2 222220 tie dne e Paun da 22 Save and Reset Exit 0 0 0 0 cece eee en 22 Set Sefial Porte hs 6 ss ee ie ee ee a 23 Serial Port Address 0 0 eects 23 Baud Rate ocioso 2 0 ep a war pee aye ete ees iss 23 Serial Port Mod i 2 2 2 a ta 24 Default Serial SettingS oooooooocoommmmm mmo 24 Adjust Videos cache bed shot eas mage Cen tat ed ee 25 AQJUSt Audio oa ieee hee ee paa Bhs BE ena ME BD cls 26 save Load Profle s iio it ala 27 Sec rity Mode rira eo 4 222 542 BO ee Ree ne Ba ara 28 Password Settings 22222220 ten ebu bE Ve eiD TE di 28 Chapter 4 Remote Operation OVEIVIGW ii une Behe ieee ra 29 Logging IN Meas Sie enslave ts te chav esate shh Ge ol ai 29 Connections Page ceste ey ea ee ee ee en 30 Toolbar u ne nal Dame 31 Configuring Connections ssas aaea aaea 31 status Colors nun er en 31 Save Load Connection ProfileS ooo oooooomoo 32 Op ration Typera nn aed da ie eee ey Aue 32 Viewing Por
31. formation ready beforehand Product model number serial number and date of purchase Your computer configuration including operating system revision level expansion cards and software Any error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 52 Appendix Specifications Function VM0808T Video Input Interface 8x RJ 45 Female Impedance 1000 Video Interface 8 x RJ 45 Female Output Impedance 1000 Video Max Bandwidth 500 MHz Max Resolution Up to 1920 x 1200 Max Distance Up to 300 m Audio Input Balanced 1 x Captive Screw Connector 5 Pole Stereo 1 x Mini Stereo Jack Female Green Output Balanced 1 x Captive Screw Connector 5 Pole Stereo 1 x Mini Stereo Jack Female Green Control RS 232 Connector 1 x DB 9 Female Black 1 x DB 9 Male Black Serial Control Pin Configurations Male Pin2 Rx Pin 3 Tx Pin 5 Gnd Female Pin2 Tx Pin 3 Rx Pin 5 Gnd Baud rate and protocol Baud Rate 19200 Data Bits 8 Stop Bits 1 Parity No Flow Control No RS 485 RS 422 Connector 1 x Captive Screw Connector Pole Ethernet 1 x RJ 45 Female Black Power Connector 1 x 3 Prong AC Socket I P Rating 100 240VAC 50 60Hz 1 0A Consumption 110 VAC 16W 220 VAC 17W Environme Operating Temp 0 50 C nt Storage Temp 20 60
32. he Output Port number to see the port name displayed See Port Name page 35 for further information 32 Chapter 4 Remote Operation Optimizing Video For the display attached to the Local port gain and compensation can be selected for optimization using these buttons For all other ports the VM0808T will adjust video levels to achieve the highest quality for all connected monitors Video Port Gain Compensation C omz ma hom adjust 1 Use the drop down menu to select a port for optimization Options are Local L All or Ports 1 8 2 Select Gain Compensation Local port only 3 Click Optimize Adjust Audio To adjust the audio do the following 1 Use the drop down menu to select a port for audio adjustment Options are Local L All or Ports 1 8 2 Use the drop down menu to select the volume level 3 Click Adjust 33 VMO808T User Manual Setup Click the Setup icon to configure the VMO808T s IP and serial settings and to name all the ports in your installation Web Setup The Web Setup settings enable you to configure the VM0808T s Web interface connection Changes take a few seconds and automatically redirect you to the IP address specified Enter values and then click Save or Clear Click Default Setting to use the following defaults IP Address 192 168 0 60 Subnet Mask 255 255 255 0 Default Gateway 192 168 0 1 Website Timeout 5 minutes
33. he connections you want to configure 2 Make changes according to the sections that follow 3 Click the Submit button The display reloads with the new status changes Or click the Clear button to revert to the stored configurations Note The latest connections will load automatically when the VM0808T 1s reset Status Colors Active connections display in color to indicate their status as follows Gray Audio Video Blue Video only Green Audio only 31 VMO808T User Manual Save Load Connection Profiles The VMO0808T allows you to store up to 16 numbered 0 15 differently configured connection profiles that can be saved and recalled later by either connection method both locally via the unit s front panel pushbuttons and over IP via the GUD Use the Save button to save the current connection profile Use the drop down list to select a saved connection profile and then click the Load button to switch to that profile Note Profile 00 is the default Operation Type Use these radio buttons to select your operation parameters There are three options You can switch audio video at the same time for all or any ports or you can switch either separately for all or any ports Video Audio Ovideo Audio Viewing Port Information The input ports can be sorted by port name or port number Use the drop down menu to select Move your cursor over t
34. he following 1 Select Serial Port Address from the Set Serial Port submenu The cursor flashes on the first number DP Serial Port Address 5 MENU NEN Baud Rate 38400 v awo ON LS een 2 Use the Up Down navigation pushbuttons to select each number 3 Use the Left Right navigation pushbuttons to move the cursor forwards backwards 4 Press ENTER to confirm the serial port address Note The default serial port address is 0 Baud Rate To set the VMO808T s baud rate do the following 1 Select Baud Rate from the Set Serial Port submenu The cursor flashes on the first number Serial PortAddress 0 REN Er gt Baud Rate 19200 v avo ON 23 VMO808T User Manual 2 Use the Up Down navigation pushbuttons to cycle through the options Baud rate options are 9600 19200 38400 and 115200 3 Press ENTER to confirm the baud rate Note The default baud rate is 19200 Serial Port Mode The VMO808T supports RS 232 RS 422 and RS 485 To set the VMO808T s serial port do the following 1 Select Serial Port Mode from the Set Serial Port submenu The cursor flashes on the entry DP _ Serial Port Model RS232 Defaul Serial Setting No 2 Use the Up Down navigation pushbuttons to cycle through the options Mode options are RS 232 RS 422 RS 485 and bypass 3 Press ENTER to confirm the Serial Port Mode Note 1 The default serial port mode is RS 232
35. information This option allows an Administrator to set reset the selected user s password add a description of the user and to set the user s privileges See below for full details Delete User Select user and click Delete to remove all user information Password Use the Edit User function to change the user s password for accessing the VMO808T s GUI This password is also used for the Telnet interface see Telnet Configuration page 34 Passwords are case sensitive and must be 5 16 alphanumeric characters Privileges Use the Edit User function to set a user s privileges The three available levels are as follows Administrator this level provides full access and control of the VMO808T functions in addition to full User Management privileges Super User this level provides full access and control with no User Management privileges User this level provides basic functions only create connections save and recall presets adjust audio Ifauser is logged into the VM0808T s GUI their user settings cannot be edited 37 VMO808T User Manual Telnet Operation The VMO808T can be operated and configured via a remote terminal session using Telnet To log in to the VM0808T by means of a Telnet session do the following 1 2 On your computer open a terminal command line session At the prompt key in the VMO808T s IP address in the following way telnet IP address 23 Pre
36. les in the rack 3 Screw the mounting brackets to the rack Chapter 2 Hardware Setup Grounding To prevent damage to your installation it is important that all devices are properly grounded 1 Use a grounding wire to ground the VMO0808T by connecting one end of the wire to the grounding terminal and the other end of the wire to a suitable grounded object 2 UVa o p Ee E ru OOOO A h 2 Make sure that all devices in your VMO808T installation including transmitters and receivers are properly grounded e a Mm o ze 1 E A AG AG A Continues on next page VMO808T User Manual 3 For increased grounding protection use STP shielded twisted pair cable to connect the Local and Remote Units There are two methods that can be used a In addition to the eight paired wires STP cable also contains a grounding wire Solder this wire to the RJ 45 connector as shown in the diagram below a b The second method is to use the STP cable shielding for grounding In this case make sure that the shielding makes tight contact with the top inside of the RJ 45 connector as shown in the diagram below N In either case make sure
37. navigation pushbuttons to cycle through the available audio input sources Options are Ports 1 8 NA none and L local 3 Press ENTER to confirm your selection to switch audio only to the selected port 4 Press AUDIO or ESC to return to the Main Page 19 VMO808T User Manual Set IP Port To configure the VMO808T s IP port settings select Set IP Port from the Menu Set IP Port Set Serial Port The sub menu provides four options IP Address Subnet Mask Gateway and Default IP Settings as follows IP Address To set the VMO808T s IP address do the following 1 Select IP Address from the Set IP Port submenu The cursor flashes on the first number gt IP Address 192 168 0 60 Subnet Mask 255 255 255 0 2 Use the Up Down navigation pushbuttons to select each number 3 Use the Left Right navigation pushbuttons to move the cursor forwards backwards 4 Press ENTER to confirm the IP address Note The default IP address is 192 168 0 60 20 Chapter 3 Local Operation Subnet Mask To set the VMO808T s Subnet Mask do the following 1 Select Subnet Mask from the Set IP Port submenu The cursor flashes on the first number 2 Use the Up Down navigation pushbuttons to select each number 3 Use the Left Right navigation pushbuttons to move the cursor forwards backwards 4 Press ENTER to confirm the Subnet Mask Note The default Subnet Mask is
38. ntact your direct vendor 56
39. on pushbuttons to select an output port s corresponding input port OUT 01 02 03 04 05 06 07 08 L men O77 XX IN loz 05 05 01 01 03 04 05 amo ES De 2 With the cursor on your selected input port use the navigation pushbuttons to cycle through the available input sources Options are Ports 1 8 NA none and L local 3 Press Enter to confirm your selection The selected audio video and RS 232 signal from the selected input is now tied to the selected output port 4 Repeat steps 1 3 for all required ports Note This operation ties all three signals audio video serial from a selected input to a selected output For independent switching of the audio signal see the following section Independent Audio In Selection 18 Chapter 3 Local Operation Independent Audio In Selection The audio signal can be switched independently of the video signal from the same input port using the Audio Main Page Press the Audio pushbutton to access this page The Audio pushbutton LED lights and the following screen appears outlal 01 02 03 04 05 06 07 08 L men 7 QA nlal L 05 05 01 01 03 04 05 woo E VG ae EL gt To create an independent audio connection do the following 1 Use the navigation pushbuttons to select the desired output port s corresponding input port OUT A 01 02 03 04 05 06 07 08 L IN a 0 05 05 01 01 03 04 05 2 With the cursor on your selected input port use the
40. ooococ E E e 41 Configuring the Serial Port 0 0 0 41 RS 232 Control Tool 1 eee 41 Switch Port Commands 00000 ernennen nn 42 Possible Values 05 05 pecan ee a 42 Mute Commands e ohe 2 be ee re eee 44 Save Load Profile Commands 0 0 e eee eee eee 45 Adjust Video Quality Commands 00 20 e eee eee 46 Adjust Audio Commands 00 ccc eee 47 Venfieationz ir szene ieh 48 Appendix Safety Instructions 2 2 assay gece as are ea en eee ar 49 Generals ee ee ra nee ok 49 Rack Mounting e ae Mace ae hate tha Siete sae 51 Technical Support oia ere eee eae 52 International nr osetia a does Pata eta ee 52 North Americas eiie na aana eine ee re aa 52 SPECIMICALIONS ied on ee a r boa A aie a 53 Troubleshooting 0 naana 55 Limited Warranty 2 ea e 56 vii VMO808T User Manual About this Manual This User Manual is provided to help you get the most from your VM0808T system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Introduction introduces you to the VMO808T system Its purpose features and benefits are presented and its front and back panel components are described Hardware Setup describes how to set up your VMO808T installation The necessary steps including how to connect up to the VE 300VE500 A V Over Cat 5 Extender system are provide
41. ort 10 Ethernet Port In order to access the VMO808T s Browser Graphical User Interface GUI the VMO808T must be connected to your network The cable that connects the VMO808T to your LAN WAN plugs in here See Cable Connection page 11 for further details 11 Cat 5 In Ports Use Cat 5e 6 cable to connect these ports to up to 8 VE500T transmitters See Cable Connection page 11 for further details 12 Cat 5 Out Ports Use Cat 5e 6 cable to connect these ports to up to 8 VE500R VE500RQ receivers See Cable Connection page 11 for further details Chapter 2 Hardware Setup device is provided on page 49 Please review it before l 1 Important safety information regarding the placement of this proceeding 2 Make sure that the power to all devices connected to the installation are turned off You must unplug the power cords of any computers that have the Keyboard Power On function Rack Mounting The VMO808T can be mounted in a 19 1U system rack For the most convenient front panel pushbutton configuration and operation at the local site mount the unit at the front of the rack as follows 1 Use the M3 x 8 Phillips head hex screws supplied with the Rack Mount Kit to screw the rack mounting brackets onto the front of the unit Phillips head hex M3 x8 Continues on next page VMO808T User Manual 2 Position the unit in the front of the rack and align the holes in the mounting brackets with the ho
42. r by either connection method To use the unit s front panel pushbuttons to save recall profiles do the following 1 Use the MENU button to access the Save Load Profile page MENU ESC Save Load Profile A SES Security Mode suo E LS omen 2 With the cursor flashing at Save Load Profiles press Enter to go to the Profiles page to save or load connection configurations DP Save a Profile No g Call a Saved Profile No 0 3 To save the current connection configuration use the Up Down pushbuttons to cycle through the numbers and press Enter to save 4 To load a Saved Profile press and release the Down button so the cursor moves to Call a Saved Profile Then use the Up Down pushbuttons to cycle through the profiles 0 15 and press Enter to select 27 VMO808T User Manual Security Mode The Security Mode page allows you to configure the VMO808T s password related settings Password Settings To configure the VMO808T s password settings do the following 1 Use the MENU button to access the Security Mode page en A Saving Calling Profile A MENU Security Mode __ auio EN 2 To set the VMO808T to require a password for local operation select Password required and use the Up Down pushbuttons to select Yes or No gt Password Required Yes MEN E Change Password 3 To change the password use the Down pushbutton to move the cursor to Change Passwo
43. rd Old Password 1234 New Password mp 0 0 4 Enter the old password see Enter Password page 17 Then press enter to move the cursor down to New Password and enter the new password in the same way 5 Press and Release Enter to confirm the password and continue to the Main Screen Note 1 If you enter an incorrect password re enter the correct password over the incorrect string 2 If Password Required see Security Mode page 28 is enabled the timeout is 5 minutes 28 Chapter 4 Remote Operation Overview The VMO808T 8x8 Cat 5 A V Matrix Switch can be configured and controlled over a standard TCP IP connection via its own Browser Graphical User Interface GUI Because the VMO808T can be accessed from anywhere on the LAN WAN or Internet remote operators can log in via Web browser using IE7 and above from any location Security is ensured by password protection and user configurable timeout The VM0808T supports four levels of remote user with various operational privileges and up to 32 users can log into the GUI at one time For full details see the sections that follow Note The VMO808T can also be accessed via a remote terminal session using Telnet See Telnet Operation page 38 for details Logging In To access the Browser GUI type the VMO0808T s IP address into the address bar of any browser The welcome screen appears VMO808T Login Username Password Login Reset
44. rt_Out_7 Port_Out_8 Output tput Name To change the display name enter a value and click Save Click Clear to revert to the previous stored named 35 VMO808T User Manual Firmware Click the Firmware icon to view information about the VM0808T s firmware version and to upgrade This is an Administrator function only Enable to check firmware version V1 1 102 Filename Browse To upgrade the VMO0808T s firmware do the following 1 Use the Browse button to locate the firmware upgrade file 2 Click Upgrade Firmware to start the upgrade Note Check the box to enable the utility to compare the VMOSOST s current firmware version with that of the upgrade files If it finds that the VMO808T s firmware version is the same or higher than the selected upgrade version it brings up a dialog box informing you of the situation and gives you the option to Continue or Cancel 36 Chapter 4 Remote Operation User Management Click the User Management icon to add edit or remove user information and to change the password for accessing the VMO808T s GUI Note This is an Administrator only function Operations are as follows Add User Click Add to add another user to the list The VM0808T supports up to 32 users at one time Edit User Select user and click Edit to change
45. ss Enter The login screen appears At the login prompt provide your Username and Password Configuration Menu Once a Telnet connection to the VMO808T is established the device s text based Configuration Menu comes up with the following items 1 H Call up the command list for help Command list GT Set gateway address IM Set IP subnet mask IP Set IP address LO Load connections from profile nn PW Change password RI Read what output is connected to nn input RO Read what output is connected to nn input SB Set the serial port baud rate SS Switch input to specified port TI Set timeout VR Software version information Ctrl Q Quit 38 Chapter 4 Remote Operation GT Set gateway address GT Old gateway address 192 168 0 1 New gateway address IM Set IP subnet mask IM Old IP subnet mask 255 255 255 0 New IP subnet mask IP Set IP address IP Old IP address 192 168 0 60 New IP address LO Load connections from profile LO 01 Load profile 01 OK PW Change password PW Old password 7 New password RI Read what input is connected to nn output RI 01 Output port 02 04 08 is connected input port 01 RO Read what output is connected to nn input RO 01 Input port 02 is connected to output port 01 39 VMO808T User Manual 9 SB Set serial port baud rate SB 96 Serial port baud rate is set to 9600 10 S
46. t Information 0 0 0 0 0c eee eee 32 Optimizing Video isi a hrer eee 33 Adjust A dIO ee ta Sore alee eee 33 SETUP a e E a eee ee et 34 Web Selup 2 222 2A aired Strahl se wie dt bel oe clad ale tls 34 Telnet Configuration 0 0000 eee 34 Seral Setup a anne ee 34 Port Names a2 a a eh ete 35 Firmware 2er A 36 User Management 0 322 ee eek sen Ka a nes 37 Password re eek 37 Privileges ora eerie a ar er ran hir 37 Telnet Operation gt iride dnare Er er 38 Configuration Menu 22 2 2424 ee ee ee 38 1 H Call up the command list for helP 38 2 GT Set gateway address 0 0 0 rennen nenn 39 3 IM Set IP subnet mask 2222er seen eee 39 4 IP SetlP Address 3 oa foc i ta ee ee eS 39 5 LO Load connections from profile 39 vi VMO808T User Manual 6 PW Change password 0 0 eee ren 39 7 RI Read what input is connected to nn output 39 8 RO Read what output is connected to nn input 39 9 SB Set serial port baud rate ooooocooocoooo ooo 40 10 SS Switch input to specified output 40 11 SV Save the current connections into profile 40 12 Tl Set timeout onno ne eee eee ee i pete es 40 13 VR Software version information 40 Chapter 5 RS 232 Commands RS 232 Serial Interface ooooooooooo
47. ult is 00 All devices Control Description VXX v Volume xx Audio level 00 15 default is 00 Example v10 47 VMO808T User Manual Verification After entering a command a verification message appears at the end of the command line as follows Command OK indicates that the command is correct and successfully performed by the switch Command incorrect indicates that the command has the wrong format and or values 48 Appendix Safety Instructions General Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device This product is for indoor use only Do not place the device on any unstable surface cart stand table etc If the device falls serious damage will result Do not use the device near water Do not place the device near or over radiators or heat registers The device cabinet is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered The device should never be placed on a soft surface bed sofa rug etc as this will block its ventilation openings Likewise the device should not be placed in a built in enclosure unless adequate ventilation has been provided Never spill liquid of any kind on the device Unplug the device from the wall outlet before cleaning Do not us
Download Pdf Manuals
Related Search