Version: 2.0
Contents
1. Version 2 0 This manual contains important laser system safety and operation information Read and understand all instructions prior to powering on laser unit the first time to avoid laser eye injury and to avoid breaking the law Keep this manual in a safe place for future reference USER MANUAL WARNING DATA Lasers can be hazardous and have unique safety considerations Permanent eye injury and blindness is possible if lasers are used incorrectly Pay close attention to each safety REMARK and WARNING statement in the user manual Read all instructions carefully BEFORE operating this device Attention a Important A Caution A Laser a Recycle eo Indoor Disposal of Location Indicates a skill or other useful information for special situations Indicates important information to protect personnel from laser incident or injury Prevent damage or injury from incorrect operation Laser safety warming labels To protect the environment recycle packing material wherever possible The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or other fluids Don t throw this product away just as general trash please dispose of this product following the abandon electronic product regulations in your area The projector must be installed in a location with adequate venti2. a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system The DXM output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit Each fixture needs to have a DMX address to receive the data from the controller The DMX address number which could be read from rear panel of each fixture is between 000 511 The end of the DMX 512 chain should be terminated to reduce signal errors 11 USER MANUAL Proper Laser Set Up amp Usage This fixture has been designed to be hung It is recommended for safety purposes your lighting effect are properly mounted using a suitable hanging clamp and safety cable Items appropriate for safe and effective mounting are easily sourced from your lighting vendor International laser safety regulations require that lasers must be operated in the fashion illustrated below with a minimum of 3 meters 9 8 ft of vertical separation between the floor and the lowest laser light vertically Additionally 2 5 meters of horizontal separation is required between laser light and audience or other public spaces a 3 Meters CAUTION Use of controls adjustments or performance of procedures other than what is specified herein may result in hazardous radiation exposure Rigging the Fixture CAUTION Please consider the respective national norms
3. during the installation The installation must only be carried out by an authorized employee or dealers 12 USER MANUAL The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated CAUTION When installing the device make sure there is no highly in inflammable material decoration articles etc in between a distance of min 0 5 meter 13 USER MANUAL PRODUCT OVERVIEW This device has left out premises in absolutely perfect condition In order to maintain this condition and to ensur
4. open or if optics appear damaged in any way Never open the laser housing The high laser power levels inside of the protective housing can start fires burn skin and will cause instant eye injury Never leave this device running unattended The operation of a class 3B laser show laser is only allowed if the show is controlled by a skilled and well trained operator familiar with the data included in this manual The legal requirements for using laser entertainment products vary from country to country The user is responsible for the legal requirements at the location country of use Always use appropriate lighting safety cables when hanging lights and effects overhead USER MANUAL LASER SAFETY LABEL REPRODUCTIONS Caution Class 3B LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM LASER RADIOATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT The label indicates the laser beam output aperture LASER EXPOSURE WARNING LASER LIGHT AVOID DIRECT EYE EXPOSURE Further guidelines and safety programs for safe use of lasers can be found in the ANSI 2136 1 Standard For Safe Use of Lasers available from www laserinstitute org Many local governments corporations agencies military and others require all lasers to be used under the guidelines of ANSI Z136 1 Laser Display guidance can be obtained via the International Laser Display Association www laserist org USER MANUAL LASER EMISSION DATA Las
5. safety regulation it is not legal to aim Class 3B lasers in areas which people can get exposed This is true even if it is aimed below people s faces such as on a dance floor Do not operate laser without first reading and understanding all safety and technical data in this manual Always set up and install all laser effects so that all laser light is at least 3 meters 9 8 feet above the floor on which people can stand See Proper Laser Set up amp Usage section later in this manual e After set up and prior to public use test laser to ensure proper function Do not use if any defect is detected Do not use if laser emits only one or two laser beams rather than dozens hundreds as this could indicate damage to the diffraction grating optic and could allow emission of higher laser levels USER MANUAL Do not point lasers at people or animals Never look into the laser aperture or laser beams Do not point lasers in areas in which people can potentially get exposed such as uncontrolled balconies etc Do not point lasers at highly reflective surfaces such as windows mirrors and shiny metal Even laser reflections can be hazardous Never point a laser at aircraft this is a federal offense Never point un terminated laser beams into the sky Do not expose the output optic aperture to cleaning chemicals Do not use laser if the laser appears to be emitting only one or two beams Do not use laser if housing is damaged or
6. 0 Grating 1 75 Clockwise grating rotating Rotation PON No grating rotating 151 255 Anticlockwise grating rotating Patterns beam effect mode when channel 1 is 225 255 000 255 11 grating patterns CHS 3 27 127 100 5 Size 128 169 169 Zooming In 170 209 Zooming Out El 210 255 Zooming In amp Out CH 4 000 127 127 0 359 degree fixed Y axis rolled Y AXIS 128 191 Clockwise rolling z aas C 21 USER MANUAL X AXIS 128 191 Clockwise moving MOVING 128 255 Anticlockwise moving CH8 000 127 128 different fixed position on Y ae CH 7 000 127 128 different fixed position on X a lt gt Y AXIS 128 191 Clockwise moving MOVING 128 255 Anticlockwise moving moving C ween 063 160 Single color Speed 000 016 Original Color 017 081 a CH 9 COLOR 161 255 Mix color alternating speed MAINTENANCE MANED ns sure the area below the installation place is free from unwanted persons during servicing Switch off the fixture unplug the mains cable and wait until the unit has been cooled down Housings fixations and installations spots ceiling truss suspensions should be totally free from any deformation The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected In order to protect the fixture from overheat the cooling fans if any and ventilation openings should be cleaned monthly The cleaning of aperture glass and scanne
7. P DOWN button it could be easily change the DMX address of the laser A pantana Se ee s FUNC UP DOWN ENTER USER MANUAL DMX PROTOCOL CHANNEL VALUE FUNCTION 000 024 Laser Block Out D 025 049 Aun Auto mixed show 050 074 Son Sound activated mixed show CH 1 MODE 075 099 Aup Auto pattern effect show 100 124 Sop Sound activated pattern effect show 125 149 Aud Auto grating effect show 150 174 Sod Sound activated grating effect show 175 199 DMX mode with grating dots effect 200 224 DMX mode with grating pattern effect 225 255 DMX mode with traditional pattern effect Grating Dots Effect mode when channel 1 is 175 199 CH 2 000 127 128 different fixed position on X X AXIS 128 191 Clockwise moving MOVING 128 255 Anticlockwise moving RG on or R amp G strobing CH 4 19 USER MANUAL 000 009 No strobing CH 5 010 249 Strobing speed __ STROBE 250 255 Strobing to sound CH6 000 075 Clockwise rotating W GRATING 076 150 ROTATION 151 255 Anticlockwise rotating gt __ al Grating Patterns Effect mode when channel 1 is 200 224 000 255 11 grating patterns 0 127 100 5 Size ROLLING Anticlockwise Anticlockwise rolling ZAK C x AX a 20 USER MANUAL CH8 000 127 128 different fixed position on Y Y AXIS 128 191 Clockwise moving MOVING 128 255 Anticlockwise OO 000 016 cho 017 081 COLOR 032 049 Red amp Green Yellow 050 255 Color Rolling No grating rotating CH1
8. cause instant blindness skin burns and fires USER MANUAL LASER SAFETY AND OPERATING INSTRUCTIONS STOP AND READ ALL LASER SAFETY DATA a Laser Light is different from any other light source with which you may be familiar The light from this product can potentially cause eye injury if not set up and used properly Laser light is thousands of times more concentrated than light from any other kind of light source This concentration of light power can cause instant eye injuries primarily by burning the retina the light sensitive portion at the back of the eye Even if you cannot feel heat from a laser beam it can still potentially injure or blind you or your audience Even very small amounts of laser light are potentially hazardous even at long distances Laser eye injuries can happen quicker than you can blink It is incorrect to think that because these laser entertainment products split the laser into hundreds of beams or laser beam is scanned out in high speed that an individual laser beam is safe for eye exposure This laser product uses dozens of milliWatts of laser power Class 3B levels internally Many of the individual beams are potentially hazardous to the eyes It is also incorrect to assume that because the laser light is moving it is safe This is not true Nor do the laser beams always move Since eye injuries can occur instantly it is critical to prevent the possibility of any direct eye exposure In the laser
9. d surrounding walls must be more than 50cm Always fix the fixture with an appropriate safety rope Fix the safety rope at the safety rope only The ambient temperature must be between 10 C to 40 C Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons CAUTION Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION If this device will be operated in any way different to the one described in this manual the product may suffer damages and the warranty void USER MANUAL BEFORE OPERATION Unpacking Instructions AN CAUTION Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling Save the package and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing What is included The carton or flight case contain following items Open Laser Light 1 PCS KEYS for key sw
10. e a safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Front Panel NO DESCRIPTION Power LED Indicates the fixture is switched on 2 Music LED Synchronize to detected music signal 2 To fasten the fixture with mounting hook The laser effect output aperture NEVER LOOK 4 Laser Aperture INSIDE THE FIXTURE THROUGH THIS APERTURE WHILE FIXTURE IS OPERATING 14 USER MANUAL Rear Panel 10 11 SAFETY EVE ATACH SAFETY CARLE HERE hs Main Power Input With IEC socket and integrated fuse holder Switch ON and OFF the fixture p Used to cool the components inside the enclosure Cooling Fan Never cover this fan outlet DMX Input 3 pins male XLR connector DMX Output 3 pins female XLR connector To control the fixture with digital LED display check Control panel more information on CONTROL amp FUNCTION Used to connect the optional emergency stopper Interlock When you push this switch the laser effect will be blank out immediately To turn the laser effect laser diode ON OFF Be Key Switch sure that only authorized operator hold the key Mic Sensitivity Turn the knob potentiometer until the laser works Knob in sync with the music To detect the music sound
11. er Classification Green Laser Medium Red Laser Medium Pulse Data All pulses lt 4Hz gt 0 25sec Divergence total light lt 160 degrees Laser Power Red gt 100mW Green gt 50mW As measured under IEC measurement conditions for classification LASER COMPLIANCE STATEMENT This laser product complies with EN IEC 60825 1 Ed 2 2007 03 and US FDA CDRH FLPPS via the terms of Laser Notice No 50 dated June 24 2007 USER MANUAL GENERAL SAFETY INSTRUCTIONS Every person involved with installation and maintenance of this device have to Be qualified Follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left out premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the devise are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not high
12. er than stated on the rear panel Always plug in the power plug least Make sure that the power switch is set to off position before you connect the device to the mains The power plug has to be accessed after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the devise is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord It is essential to connect the yellow green conductor to earth USER MANUAL The electric connection repairs and servicing must be carried out by a qualified employee Do not switch the fixture on and off in short intervals as this would reduce the laser diode life For replacement please use fuses of same type and rating only If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The minimum distance between the fixture an
13. itch 2 PCS a Interlock Connector 1 PCS Mains Cable 1 PCS fi USER MANUAL 1 PCS Power Supply To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture of refer to the fixture s specifications chart A fixture s listed current rating is its average current draw under normal conditions All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch Before applying power to a fixture check that the source voltage matches the fixture s requirement USER MANUAL The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration FUSE 5mmx20mm FUSE F 1 A 250V Cablu Cabeus Pin International DMX 512 connection between fixtures The fixture is equipped with 3 pin XLR sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal A Caution At the laser f
14. ixture the DMX cable has to terminated with a terminator Solder a 120 Ohm resistor between Signal and Signal into a 3 pin XLR plug and plug and plug it in the DMX output of the last fixture PIN 3 PIN 2 10 USER MANUAL Building a serial DMX chain ans TN 7 7 aT a 5 menr a i aie e 44 iki ad He He i i t JMX 512 12002 it Controller operation ijj A W H u Masterisiawe eer y ft operation il 12042 _ _ _ cae a t 1200 If you are using the standard DMxX controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMxX chain If you wish to connect DMxX controllers with other XLR outputs you need to use adapter cables Connect the DMX output of the first fixture in the DMX chain with the DMxX input of the next fixture Always connect output with the input of the next fixture until all fixtures are connected lf you use a controller with 5 pins DMX connector you need to use a 5 to 3 pins adpter At last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pins XLR plug and plug it in the DMX output of the last fixture Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable DMX 512 is
15. lation at least 50cm 20 inches from adjacent surfaces Be sure that no ventilation slots are blocked USER MANUAL LASER SAFETY WARNINGS a Potential laser injury hazard exists with this product Read these instructions carefully which includes important information about installation safe use and service Caution caution Caution caution caution Caution Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser light This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes It is illegal and dangerous to shine this laser into audience areas where the audience or other personnel could get direct laser beams or bright reflections into their eyes It is a US Federal offense to shine any laser at aircraft There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact the dealer nearest to you Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure NON INTERLOCKED HOUSING WARNING This unit contains high power laser devices internally Do not open the laser housing due to potential exposure to unsafe levels of laser radiation The laser power levels accessible if the unit is opened can
16. ow Press FUNC to enter MODE OPTION Till to LED panel shows either one of Aut Aup Aud amp Sou Press UP or DOWN to select your favorite Stand Alone mode as above Press ENTER to confirm the setting The laser is working in stand alone Each time when you turn on your laser you will have this confirmed laser show FUNC UP DOWN ENTER In the MODE OPTION setting the stand alone laser show that you are going to choose is flashing Press UP or DOWN to change stand alone laser show you will have 6 different stand alone preprogrammed laser show Their DISPLAY and EFFECT are listed below USER MANUAL DISPLAY STAND ALONE MODE LASER EFFECT SON Sound activated mixed show Pattern effect Grating effect AUN Auto running mixed show Pattern effect Grating effect SOD Sound activated grating effect show AUD Auto running grating effect show SOP Sound activated pattern effect show AUP Auto running pattern effect show MASTER SLAVE MODE e Press FUNC to enter MODE OPTION e Till to LED panel shows SLA e Press ENTER to confirm the setting The laser is working in SLAVE MODE Connect MASTER laser and SLAVE lasers with DMX cable the SLAVE lasers do what exactly MASTER laser does Check 5 2 DMX connection to have more details about laser connection DMX MODE e Press FUNC to enter MODE OPTION e Till to LED panel shows 001 e Press ENTER to confirm the setting The laser is working in DMX MODE With help of U
17. r mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics 1 Clean with a soft cloth using normal glass cleaning products 2 Always dry the parts carefully 3 Clean the Aperture glass at least once every 30 days The interior of the fixture should be cleaned annually using a vacuum cleaner or air jet 22 USER MANUAL SPECIFICATIONS Mains Input Fuse Total Power Music Control Laser Power Laser Classification Laser Safety Standard Condition Temperature DMX Connections DMX Channels Measurement N Weight AC100 240V 50 60Hz 250V 1 6A Slow Blow 20mm Glass 28W Internal microphone 50mW 532nm Green CW 100mW 650nm Red CW Class 3B EN60825 1 2007 10 40 C 3 pins XLR Male Female 6 10 9 channels See diagram below 2 6 Kg Specifications subject to change without prior notice The availability of particular products may vary by region Please check with the dealer 23
18. signal 15 Used to attached a safety cable when the fixture is 11 Safety Eye S rigged Check more details in RIGGING USER MANUAL IMPORTANT For your own safely and full laser safety regulation we do strongly recommend you to take this optional switch CONTROL amp FUNCTION Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use Do not switch the unit on and off in short time intervals Always unplug the unit when it is not used for a longer time Or before replacing the bulb or start servicing In the event of serious operation problems stop using the fixture and contact your dealer immediately A Attention Laser will be output from laser aperture in 5 seconds after the unit is powered on Operating Mode When laser is powered on LED monitor on rear panel shows the current operating standalone mode or DMX address of DMX mode With help of LED control panel it is very easy to set and change the operating mode of laser After every resetting and saved the new mode information will be shown on LED monitor at next power on FUNC Mode Function Option to choose the operating mode of laser ENTER Confirmation to confirm all setting or change of LED control panel UP DOWN to change operating mode parameter or DMX address DOWN 16 USER MANUAL Operation POWER ON LASER FUNG Stand Alone Preprogram Laser Sh
Download Pdf Manuals
Related Search