INSTALLATION / OPERATION USER`S MANUAL
Contents
1. SIDE VIEW 00000900 e E RN f Na f LOW sa YZ P 5 9J mai n a o9 0O e eo _ Faz ca jo l Mu 11 FOCUS ADJUSTING FIXING screw Tighten this screw after focus the lens of a camera AUTO IRIS LENS connector Connect the DC auto iris lens 4 pin connector into this connector to control the amount of light allowed through the lens REAR VIEW D Left Button 2 Up Button 8 Enter Button Right Button 1 5 Down Button 5 Day Night External IN 7 Motion ALARM OUT 10 RS 485 9 Power Indicator 8 9 HD SDI OUT 7 Video Output Connector BNC DC12V IN AC24V IN CAMERA INSTALLATION Connection Overview External Converter MegaPixel Camera Mega Stream through Coaxil Cable FULL HD MONITOR Starting Installation 1 Install the Lens Be careful the lens does not touch camera sensor when installer try to enter the lens into camera Install manual lens or DC auto iris lens If DC auto iris lens needs to install connect DC auto iris 4 pin connector into iris drive connector located on the side of the camera 2 Mount the camera The camera can be mounted from both top side and bottom side 3 Connect other peripheral devices 3 1 Connect the other peripheral devices such as Alarm D amp N IN and BNC connector 3 2 Coaxial Cable is connected to the HD SDI camera and the Converter 3 3 The HDMI Cable is conne2. 11 CONNECTIONS DAY amp NIGHT IN amp ALARM OUT TERMINALS 14 SPECIFICATIONS 16 CONTENTS OF PACKAGE Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment The content of the package includes 1 Color CMOS HD SDI Camera 2 Mini DIN connector DC type auto iris lens 3 CS adapter ring for C mounting C lenses 4 This manual INTRODUCTION Full HD 2Mega pixel Camera HD SDI 1080 30fps HD SDI amp Composite Video OUT Features Full HD 1920x1080p Real Time High definition 1080p video over 100m of RG59 or equivalent cable Advanced Technology for Surveillance WDR Wide Dynamic Range BLC 3D Digital Noise Reduction Digital Image Stabilization Digital Slow Shutter Digital Zoom x10 Max Removable IR Cut Filter for Day amp Night Privacy Zone Masking Video Motion Detection Day amp Night function Single 75Q coaxial bi directional RS 485 interface RS 485 interface HD SDI Out CVBS Out Alarm OUT D amp N IN Quick connect for DC lens with 4 pin connector User Certified Listed Class 2 power source only Operates in 12VDC or 24VAC CAMERA OVERVIEW TOP VIEW
3. camera identification to assign a number and character to the camera 0 to 9 A to Z a to z To disappear the user title select OFF USER TITLE 1 Select the USER TITLE option on the SPECIAL screen 2 Use lt or gt button to select ON then click n button The USER TITLE menu appears 3 Use A V or button to select a character or number then click 4 button CLR Clear all entered characters and numbers POS Move the USER TITLE position on the screen using the arrow buttons END Confirm your selection or exit the setting Blank Insert a space at the cursor position gt Moves cursor to left or right LANGUAGE Select the viewer language for the camera setup menu and OSD information display FRAME RATE You can select the HD 30fps or 25fps IN 50Hz lighting Condition 25fps recommended RESET setting CAMERA REBOOT Reboot the camera system FACTORY RESET Clear certain setting and information and return to factory default settings The camera is restarted without changing any of the setting CONNECTIONS DAY amp NIGHT IN amp ALARM OUT TERMINALS 1 DAY amp NIGHT IN Terminals To select Day Night mode using external equipment by connecting control lines to the appropriate terminals e DAY NIGHT EXTERNAL INPUT Switches the cameras D N mode to either Day or Night based on the input status Refer to the diagram below The cameras D N mode must be set to EXT for this to function 4
4. white balance options manually The color temperature range for the white balance is approximately 5100K gt RED set desired red value gt BLUE set desired blue value Day amp Night setting The D amp N controls the position of the IR Infra Red cut filter which determines the color or black white setting of the camera Day amp Night mode Select a mode for DAY NIGHT function Auto Day amp Night mode changes automatically Day Color mode enabled Night Black and white mode enabled EXT This menu automatically converts the COLOR Mode into the B W Mode or vice versa depending on illumination with an external sensor Motion DET setting When motion is detected in the area of setting an alarm signal is output MOTION DET OFF ON Select a mode for M ON M OFF function ZONE NUMBER Select a motion for area ZONE STATE Select a range of motion display box HEIGHT WIDTH motion display box scaling MOVE Y MOVE X motion display box Move SENSITIVITY Action sets the sensitivity 3D DNR setting 3Dimensional Digital Noise Reduction function dramatically cleans up the noise in video frames and solves the problem of low light sensitivity where it can display high image resolution even in extremely low light conditions Level Select one of the 3D DNR levels Off Not in use High Select a High level Middle Select a Middle level Low Select a Low level lt PRI
5. CE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB 003 DU CANADA CE COMPLIANCE STATEMENT WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth N ee o M a Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves c or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenien
6. COM 4 Open contact DAY DAY amp NIGHT INPUT Close contact NIGHT 2 ALARM OUT TTL level Motion detection signals are output through this port Active state is configurable 3 ALARM OUT lt ALARM OUT Normal 0V COM 2 ALARM OUT Active 5V Period Alarm out period 5sec 3 CAMERA CONTROL e 1PIN RS 485 e 2PIN RS 485 4 POWER INPUT TERMINAL I e This terminal accepts a DC12V or AC24V power ei source from a DC12V or AC24V ac 10 60 50Hz 1Hz De 12V e Use Certified Listed Class 2 power supply only AC 24V It is recommended to use the DC power supply that can support inrush current over 0 75A min SPECIFICATIONS Item HD SDI Camera Power Power source DC 12V AC 24V 10 Power consumption 12Vdc 0 3A Lens Optional Image sensor 1 2 8 2Mega Pixel CMOS Sensor Effective pixels 1920 H x1080 V Scanning Mode Progressive Scan Supported Lens Type Auto DC Iris Manual Iris Low Light Sensitivity 0 3Lux HD SDI Output 1920x1080p 30fps Resolution TBD TVL Output Format HD SDI SMPTE 292M 75 Ohm BNC nece Composite 1Vp p 75 Ohm BNC General enaratio 50dB AGC OFF Camera control RS485 Faxtrax Pelco D Pelco P White Balance AUTO ATW MANUAL AWC Push AUTO White Balance Range 2500 K 9600 K Exposure ALC ELC HSBLC BLC WD
7. Damp Coil Red 3 Drive Coil White 4 Drive Coil Green Figure 2 DC auto iris Lens connection OSD Menu Setup The following table shows the list of menu items and options You can adapt the camera to your requirements by setting up the respective items in these menus Main Menu Sub Menu Contents WDR BLC OFF WDR BLC HSBLC BRIGHTNESS 0 to 100 AGC OFF LOW MIDDLE HIGH EXPOSURE ELC ALC SHUTTER At 4 Pr abr E OFF SENS UP pA EXIT RET TOP END ATW AUTO 5 AWC b PUSH WHITE BAL COLOR TEMP INDOOR OUTDOOR RED 100 to 100 MANUAL BLUE 100 to 100 EXIT RET TOP LEVEL LOW MIDDLE HIGH DWELL TIME 5 10 15s DAY NIGHT AUTO EXIT RET TOP END DAY NIGHT OFF ZONE NUMBER AREA1 to AREA4 ZONE STATE ON OFF HEIGHT 2 to 6 MOTION DET WIDTH 2 to 8 MOVE Y 1to5 MOVE X 1to7 SENSITIVITY 0 to 100 EXIT RET TOP END OFF LOW eee MIDDLE HIGH OFF COLOR RED GREEN BLUE 0 to 255 PRIVACY TRANSPARENCY 0 to 16 um RECTANGLE MASK NUMBER AREA to AREA8 RECT DISPLAY ON OFF HEIGHT 4 to 100 WIDTH 4 to 100 MOVE Y 2 to 98 MOVE X 2 to 98 MASK NUMBER AREA1 to AREA2 CIR DISPLAY ON OFF HEIGHT 1 to 15 GIREEE WIDTH 1 to 15 MOVE Y 0 to 100 MOVE X 0 to 100 RADIUS SIZE 0 to 100 MASK NUMBER AREA to AREA2 POLYG
8. INSTALLATION OPERATION USER S MANUAL Full HD SDI CAMERA WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT CAUTION RISK OF ELECTRNIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons PRECAUTIONS Should any liquid or solid object fall into the cabinet unplug the unit and have it checked by the qualified personnel before operating it any further Unplug the unit from the wall outlet if it is not going to be used for several days or more To disconnect the cord pull it out by the plug Never pull the cord itself Allow adequate air circulation to prevent internal heat build up Do not place the unit on surfaces rugs blankets etc or near materials curtains draperies that may block the ventilation holes Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel
9. ON POLY DISPLAY ON OFF POLYGON DRAW POLYGON MOVE EXIT RET TOP END OFF ZOOM D ZOOM ON D EFFECT OFF MIRROR ROTATE V FLIP SHARPNESS 0 to 68 alae COLOR OFF ON STABILIZER OFF ON USER TITLE OFF ON LANGUAGE English German French Spanish Italian Russian FRAME RATE 30fps 25fps EXIT RET TOP END CAMERA REBOOT RESET FACTORY RESET EXIT EXIT CAMERA OPERATION Main Menu Click 4 Button on the OSD control Window The camera setting menu appears on the view picture CAMERA SETTING gt CAMERA ID OFF EXPOSURE ALC WHITE BAL ATW DAY NIGHT AUTO MOTION DET OFF 3D DNR HIGH PRIVACY OFF SPECIAL lt RESET EXIT lt Use up or down button to select an option the push button submenu appears use up or down button to select a submenu option Use right or left button to select a value Select lt exit gt option then push enter button to exit the setup menu In the Submenu use right or left button to select a mode and push enter button To exit the setup menu RET return to the previous TOP return to camera setting menu screen END exit the setup menu Exposure setting Exposure is the amount of light detected by the camera sensor A scene with correct exposure settings has adequate detail and contrast between white and dark values An image with too little or too much exposure determines detail in the scene The camera features auto and manual exposure settings Exposure
10. R AGC Off Low Middle High Shutter Speed Auto Off X64 to X2 AntiFlk 1 160 to 1 10000 Wide Dynamic Range 68 dB 5 User Title Character 0 to 9 A to Z a to z N Display Off On User Title x 3D DNR Off Low Middle High Day amp Night Auto Day Night Ext i True Day Night IR Cut Pass Filter Privacy zone Color Transparency Rectangle Circle Polygon D Effect Off MIRROR ROTATE V FLIP Sense up x64 Sharpness 0 68 steps Cam ID 001 255 WDR Limit Low Middle High D Zoom ZOOM x10 PAN TILT Stabilizer Off On Language English German French Spanish Italian Russian Power input Terminal block Auto iris output 4 Pin mini din jack standard connection Connec tor Lens mount C CS mount amp etc Mounting hole 1 4 20 UNC top or bottom Control and Connection DIN In Alarm Out RS485 Operating Temp 10 C to 50 C Operating humidity Less than 90 External dimension 66 W x 56 H x 120 D mm Weight 280g only camera 17
11. VACY setting gt Use the Privacy Mask tab for aiming at the protection of personal privacy Mode Select an ON mode for Privacy Mask function Off Not in use On Set and Use the P Mask function 1 Select an ON mode and click the Save button Then P Mask OSD windows will be appears 2 Click the Enter button for PRIVACY SETUP OSD menu Color R G B You can make any color by adjusting R G B level TRANSPARENCY You can adjust the transparency of MASK REC CIR POL RECTANGLE 1 Use Left Direction or Right Direction button to select a mask on the MASK NUMBER 2 Use Left Direction or Right Direction button to set up the ON or OFF on the RECT DISPLAY option 3 Use Upper Direction or Lower Direction button to select an option then use Left Direction or Right Direction button to adjust the option HEIGHT Increase or decrease the vertical size of the mask WIDTH Increase or decrease the horizontal size of the mask MOVE X Moves horizontal position of the mask MOVE Y Moves vertical position of the mask CIRCLE 1 Use Left Direction or Right Direction button to select a mask on the MASK NUMBER 2 Use Left Direction or Right Direction button to set up the ON or OFF on the CIR DISPLAY option 3 Use Upper Direction or Lower Direction button to select an option then use Left Direction or Right Direction button to adjust the option HEIGHT Increase or decrease the vertical si
12. ce receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been moisture does not operate normally or has been dropped 15 CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO 16 Use satisfy clause 2 5 of IEC60950 1 UL60950 1 or Certified Listed Class 2 power source only TABLE OF CONTENTS CONTENTS OF PACKAGE 3 UISUT RCD WIC TO Nace eral cereal a 6 CAMERA OVERVIEW sore eee ee 7 CAMERA INSTALLATION 8 OSD Menu Setup 10 CAMERA OPERATION
13. cted to the Converter and the FULL HD Monitor 4 Supply the camera with power Connect DC12V or AC24V wires to the camera power connector Be careful when DC12V wiring especially the direction of positive and negative Use power supply compatible with FCC Class2 The camera will complete a configuration processing within approximately 4 5 seconds 5 View the camera image NOTES Use megapixel lens for higher image quality Megapixel lenses are designed and tested to deliver optimal image quality to the HD SDI megapixel cameras If the standard definition lens was installed on megapixel camera the image quality will be poor than expected Recommend to install the megapixel lens from the following lens manufactures TAMRON COMPUTAR FUJINON DC Auto Iris Lens Installation amp Adjustment The camera supports DC type auto iris lenses Perform the following steps to install and adjust a DC type auto iris lens Solder the lens control wires to the connector supplied with the camera Rib Connector EF Eius Cover N Automatic V un Iris Lens Pin 1 Heat Pin4 Shrinkable Tubes Iris Control Cable Pin 2 Connector Figure 1 4 Pin iris driver connector Attach the DC type auto iris lens to the lens mount on the front of the camera Plug the connector into the auto iris jack on the side of the camera The connector is polarized and can be inserting into the iris jack one way 1 Damp Coil Blue 2
14. mode Supports exposure modes to control the amount of light detected by the camera sensor base on settings for light conditions The default setting is ALC ALC Automatic Light Control for indoor scenes ELC Electronic Light Control for outdoor scenes WDR BLC Use WDR BLC option to view the object clearly in backlight condition WDR Wide Dynamic Range feature can be very helpful to cope with very challenging lighting conditions It is capable of capturing both of the dark part and bright part and combining the differences into a scene to generate a highly realistic image as original scene BLC Back Light Compensation feature helps to alleviate the issues of visibility in high contrast area HSBLC Highlight Suppression Back Light Compensation Brightness The image brightness can be adjusted in the range 0 20 where a higher value produces a brighter image AGC Select an AGC level according to Mode selection NOTE If you set AGC to OFF then the Day and Night Auto SENS UP and 3D DNR are not available Shutter speed Select a Shutter speed option X64 to X2 Set to the slow shutter Auto Adjust the shutter speed automatically Off Fix to the shutter speed AntiFlk Set the shutter to anti flick mode 1 160 to 1 10000 Set to the fast shutter NOTES If you set Shutter speed to Auto then the WDR and SENS UP are available If you set Shutter speed to AntiFlk then the WDR i
15. only The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product Installation Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust mechanical vibration The unit is not designed to be waterproof Exposure to rain or water may damage the unit Cleaning Clean the unit with a slightly damp soft cloth Use a mild household detergent Never use strong solvents such as thinner or benzene as they might damage the finish of the unit Retain the original carton and packing materials for safe transport of this unit in the future FCC COMPLIANCE STATEMENT FCC IN FO RMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFEREN
16. s available In Shutter speed mode the WDR and SENS UP are not available except that the mode is Auto or AntiFlk Sens Up If pictures are not clear due to darkness this SENS UP operation would increase the sensitivity of picture Off Not in use Auto Adjust the sensitivity of the picture automatically Sens Up level Select the Sense Up level x2 to x64 lt White Balance setting gt White Balance Control defines how the camera processes video images to render true colors in a scene White balance is especially effective in scenes with changing lighting conditions or in scene with more than one type of light source White balance mode Provides the options for White Balance The default setting is ATW ATW Auto Tracking White Balance In this mode white balance has better coverage than AUTO Proper white balance may not be obtained under the following condition gt When the scene contains mostly high color temperature objects such as a blue sky or sunset Auto Set the white balance mode automatically AWC_PUSH Auto White Balance Control If you select this mode you will be able to set up the White Balance by push triggered white valance in fixed mode Manual You can set the white balance options manually gt Color TEMP use right or left button to select a function Indoor Set the white balance options manually The color temperature range for the white balance is approximately 3200K Outdoor Set the
17. ze of the mask WIDTH Increase or decrease the horizontal size of the mask MOVE X Moves horizontal position of the mask MOVE Y Moves vertical position of the mask RADIUS SIZE You can adjust the RADIUS SIZE POLYGON 1 Use Left Direction or Right Direction button to select a mask on the MASK NUMBER 2 Use Left Direction or Right Direction button to set up the ON or OFF on the POLY DISPLAY option 3 Use Upper Direction Lower Direction Left Direction Right Direction and Enter buttons to draw the polygon by moving each vertex on the POLYGON DRAW Each movable spot each time you can click the Enter button 4 Use Upper Direction Lower Direction Left Direction Right Direction and Enter buttons to move the polygon on the POLYGON MOVE lt SPECIAL setting gt Implement various functions D ZOOM You can select the digital zoom level D EFFECT You can select the digital effect SHARPNESS The degree to which boundary of the two portions is clearly distinguished COLOR You can switch the displayed picture to gray scale or color STABILIZER The image stabilizer function minimizes the appearance of shaky images caused by low frequency vibration This function is useful for outdoor surveillance Select the STABILIZER option and set to ON or OFF Note If you set the STABILIZER to ON the Digital zoom is set to x1 1 automatically USER TITLE You can use the
Download Pdf Manuals
Related Search