Products Manual - Power Equipment Direct
Contents
1. CONNECTIONS Connections on pressure washer hoses gun and spray wand should be cleaned regularly and lubricated with light oil or lithium grease to prevent leakage and damage to the o rings NOZZLE The nozzles should be cleaned regularly Clogging of the nozzle causes diminished performance and the pump pressure to be too high and cleaning is immediately required 1 Remove the wand from the gun 2 Clear the nozzle by forcing a stiff wire or straightened out paper clip small size through the center hole of each nozzle 3 Backflush the nozzle with water from both ends 4 Reconnect the wand to the gun Restart the pressure washer and depress the trigger on the spray gun LUBRICATION The pressure washer is designed with a permanent lubrication system Conventional oil checks and changes are not necessary NOTE In case of oil leakage contact our customer service department at www power washer us or 1 800 381 0999 A SMALL AMOUNT OF OIL LEAKAGE IS NORMAL WATER SCREEN FILTER The pressure washer is equipped with a water inlet screen filter to protect the pump Never operate the pressure washer without the screen filter in place CAUTION f the screen filter is not kept clean the flow of water to the pressure washer will be restricted and the pump may be damaged e To clean the inlet water screen filter remove garden hose connector D and remove the screen filter from the inlet e Flush2. BLACKS DEGKER Model Modelo 11BDE 210 INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Go to www power washer us to register your new product Vaya a www power washer us para registrar su nuevo producto If your pressure washer is not working properly or if there are parts missing or broken please DO NOT RETURN IT TO THE PLACE OF PURCHASE Contact our customer service department at www power washer us or 1 800 381 0999 Si su lavadora a presi n no trabaja correctamente 6 encuentra partes rotas faltantes por favor NO LA REGRECE AL LUGAR DONDE LA COMPRO Cont ctese con nuestro Departamento de Servicio al Cliente llamando al www power washer us o 1 800 381 0999 VEA EL ESPANOL EN LA CONTRAPORTADA INSTRUCTIVO DE OPERACI N CENTROS DE SERVICIO Y POLIZA DE GARANT A ADVERTENCIA LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO SAVE THIS MANUAL FOR FUTURE REFERENCE Part No XXXXXXX Rev 0 JAN 2011 EASY INSTALLATION A WARNING CAREFULLY READ THE OPERATORS INSTRUCTIONS BEFORE USING THE PRESSURE WASHER FOR THE FIRST TIME ALWAYS STORE YOUR PRESSURE WASHER IN A LOCATION WHERE THE TEMPERATURE WILL NOT FALL BELOW 40 F 4 C FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY INSTALACI N F CIL A AVERTENCIA LEA ATENTAMENTE EL MANUAL DE INSTRUCCIONES ANTES DE PONER EL EQUIPO POR PRIMERA VEZ EN FUNCIONAMIENTO TIENE QUE PONER SIEMPRE LA M QUINA DE LAVAR A PRESI N EN UN SITIO DONDE LA TEMPERATURA NO DIMINUE
3. To prevent damage the cord should not be crushed placed next to sharp objects or near a heat Source Check power cords before using Damaged cords can reduce performance of pressure washer or cause a fatal electrical shock The narrow pin point stream is very powerful It is not recommended for use on painted surfaces wood surfaces or items attached with an adhesive backing Keep operating area clear of all persons and animals Always use both hands when operating pressure washer to maintain complete control of the wand Do not touch nozzle or water spray while operating Never place hands in front of nozzle Wear safety goggles while operating Wear protective clothing and footwear to protect against accidental spraying Disconnect power plug from the outlet when not in use and prior to the detaching of the high pressure hose 22 23 24 25 26 27 28 29 30 5 ENG Never tie knots or kink the high pressure hose as damage could result Inspect the high pressure hose regularly Replace the hose immediately if it is damaged worn or shows any signs of cracks bubbles pinholes or other leakage Never grasp a high pressure hose that is leaking or damaged Do not operate or store this product in temperatures below 40 F 4 C Freeze damage is not covered by the warranty Carefully observe all chemical instructions and warnings before using Use only approved pressure was
4. the spray gun may be malfunctioning and need to be replaced Please contact our customer service department at www power washer us or by calling 1 800 381 0999 19 ENG OPERATIONAL POSSIBLE SOLUTION ISSUE CAUSE Connecting and To attach the Lance apply steady downward Disconnecting pressure on the lance In the direction of the the Spray Lance trigger while simultaneously twisting the NOTE Due lance 90 counterclockwise It may help if to the high you set the gun vertically on a flat surface pressures with the lance pointing upwards The two produced by your pressure washer the lance must seal tightly to the gun As the result of normal operation the lance can become difficult to attach or remove and this process may require considerable force tabs on the end of the lance must be fully inserted in the gun before the lance will twist and lock If this does not work then remove the bayonet o ring from the end of the lance and attach the lance to the gun without the o ring in place If the lance attaches to the gun without the o ring in place you will need to replace the o ring Please contact our customer service department at www power washer us or by calling 1 800 381 0999 To remove the Lance release any trapped pressure in the gun hose by turning the unit OFF and squeezing the gun trigger Apply steady downward pressure on the lance In the direction of the trigger while simult
5. Click N Clean nozzle has three spray settings Turn the collar 120 to the desired position S oe b Low Pressure R Soap position is intended for dispen sing detergent E The High Pressure c Medium Fan Spray position is intended for cleaning with high pressure U The High Pressure Wide Fan Spray position is intended for cleaning with high pressure di NOTE The pressure of the spray on the surface you are cleaning increases as you move the wand closer to the surface HIGH PRESSURE TURBO SPRAY LANCE FIG 5 A CAUTION Do not attempt to move the nozzle to adjust pressure The turbo nozzle is NOT adjustable The high pressure turbo nozzle N is intended for maximum cleaning effect Keep the spray lance a minimum of 6 8 in 15 20 cm away from the cleaning surface at all times USING DETERGENT FIG 6 7 NOTICE Use only approved pressure washer cleaners Do not use bleach chlorine or any cleaners containing acids NOTICE Fill and flush the detergent tank with clear water after use 1 Insert the spray lance B into the gun A by pushing firmly and simultaneously twisting a 1 4 of a turn counterclockwise until locked into place 2 Remove the tank cap V present on the back of the machine 10 ENG 3 Fil the tank J with suitable cleaning solution 4 Place the Click N Clean spray lance into the Low Pressure
6. EN LA PISTOLA A o0 TUERZA LA LANZA 90 DEL AEROSOL A LA IZQUIERDA A CON SEGURIDAD SE TRABAN EN LUGAR FULLY OPEN TURN INCOMING WATER ON ABRA COMPLETAMENTE NOTE USE COLD WATER ONLY GIRE EL AGUA ENTRANTE NOTA UTILIZAR S LO AGUA FR A PLUG GFCI C INTO POWER RECEPTACLE FIRMLY PRESS O AND RELEASE THE TEST E BUTTON X THEN PRESS AND t RELEASE THE RESET BUTTON eo W THE LIGHT ON THE GFCI SHOULD BE ILLUMINATED ENCHUFE EL GFCI C A UN TOMACORRIENTE PRESIONE CON FIRMEZA Y SUELTE EL BOT N DE PRUEBA TEST X Y LUEGO PRESIONE Y SUELTE EL BOT N DE REINICIO RESET W SE DEBE ENCENDER LA LUZ DEL GFCI SQUEEZE AND HOLD TRIGGER UNTIL WATER FLOW IS STEADY RELEASE THE TRIGGER MANTENGA PULSADO EL ACCIONADOR HASTA QUE EL CAUDAL DE AGUA SE VUELVA CONSTANTE SUELTE EL ACCIONADOR TURN SWITCH TO ON POSITION I AND SQUEEZE TRIGGER TO START MOTOR AND WATER FLOW NOTE motor only runs when trigger is depressed and water is spraying SITUAR EL INTERRUPTOR EN LA POSICI N DE ON I Y APRETAR EL GATILLO PARA PONER EN MARCHA EL MOTOR Y EL FLUJO DE AGUA NOTA el motor funciona solamente cuando se presiona el disparador y el agua est rociando SAFETY GUIDELINES DEFINITIONS This manual contains information that is important for you to know and understand This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS To help you recognize this information we use the symbols below Pl
7. drawings used in this manual are for reference only and do not represent a specific model Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments Save this manual for future reference A B C D mm Spray Gun Click N Clean Spray Lance GFCI Garden Hose Connector factory installed High Pressure Hose Safety Lock o Ov 8 ENG SZ ST et In Motor and Pump in Case Power Supply Cord with GFCI ON OFF Switch On board Detergent Tank High Pressure Outlet metal Shipping Plug Water Inlet plastic On Board Accessory Storage Holsters Water Inlet Filter Screen factory installed inside water inlet M Carry Handle Hose Cord Storage Location Turbo Lance ASSEMBLY INSTRUCTIONS FIG 3 1 Locate and remove all loose parts from the carton 2 With handle oriented as shown align grooves in carry handle P with rails on top of pressure washer and slide into place 3 Push as shown to further lock carry handle into place 4 Align slots BB on back of storage rack with ribs AA on back of pressure washer 5 Slide storage rack down until it locks into place 6 Remove and discard the shipping plug L from the outlet K on the front of the machine OPERATING INSTRUCTIONS PRESSURE WASHER TERMINOLOGY PSI Pounds per Squa
8. BAJO 4 C 40 F LOS DANOS QUEL EL HIELO PROVOCA NO SON REMBOLSDADO DE LA GARANTIA WITH RAILS ON TOP OF PRESSURE WASHER AND SLIDE INTO PLACE PUSH AS SHOWN TO FURTHER LOCK CARRY HANDLE INTO PLACE CON LA MANIJA ORIENTADA COMO SE MUESTRA ALINEE LOS SURCOS ADENTRO EL AGARADOR DE LA MAQUINA P CON LOS CARRILES ENCIMA DE LA MAQUINA DE PRESION Y RESBALAN DENTRO DE LUGAR EMPUJE COMO SE MUESTRA A CONECTAR EL AGARADOR DE LA MAQUINA GP WITH HANDLE ORIENTED AS SHOWN ALIGN GROOVES IN CARRY HANDLE P ALIGN SLOTS BB ON BACK OF STORAGE RACK WITH RIBS AA ON BACK OF PRESSURE WASHER SLIDE STORAGE RACK DOWN UNTIL IT LOCKS INTO PLACE ALINE LAS LINEAS BB ATRAS DEL ALMA CENAMIENTO CON LAS LINEAS AA ATRAS DE LA LAVADORA DESLICE EL ALMACE NAMIENTO PARA ABAJO HASTA QUE ESTE SEGURO REMOVE AND DISCARD THE SHIPPING PLUG L FROM THE OUTLET K ON THE FRONT OF THE MACHINE EXTRAER EL TAPONES L DE TRANSPORTE DEL EMPALME DE LA M QUINA K Y ELIMINARLO CONNECT THE HIGH PRESSURE HOSE E TO THE MACHINE OUTLET K CONNECT EL TUBO DE ALTO PRESI N E A LA SALIDA DE LA M QUINA K CONNECT THE GARDEN HOSE Y TO THE CONNECTOR D ON THE FRONT OF THE MACHINE CONECTE LA MANGUERA DEL JARDIN Y AL CONECTOR D CORRESPONDIENTE ACOPLADO A LA ENTRADA DE LA MAQUINA INSERT THE SPRAY LANCE B R INTO THE GUN A TWIST SPRAY LANCE 90 COUNTERCLOCKWISE TO SECURELY LOCK IN PLACE PARA INSERTAR LA LANZA dq B R
9. Soap position S fig 4 5 Squeeze the trigger and the detergent will automatically be mixed with the water and dispensed from the nozzle NOTE When the Click N Clean nozzle is moved to the High Pressure Medium or High Pressure Wide Fan Spray position detergent will not be dispensed 6 When you have completed the use of detergent Fill and flush the detergent tank with clear water after use See Storage for correct procedure 7 See Storage section in this manual for proper shutdown and storage procedures Cleaning techniques When cleaning with the pressure washer some cleaning tasks can be solved with water alone but for most tasks it is advantageous to use a detergent A detergent ensures a quick soaking of the dirt allowing the high pressure water to penetrate and remove the dirt more effectively Application of detergent N CAUTION Avoid working on hot surfaces or in direct sunlight to mini mize the chance of the soap damaging painted surfaces A CAUTION Damage may occur to painted surface if soap is allowed to dry on the surface Wash and rinse a small section at a time 1 Apply the solution to a DRY work surface NOTE WETTING THE SURFACE FIRST IS NOT RECOMMENDED AS IT DILUTES THE DETERGENT AND REDUCES ITS CLEANING ABILITY On a vertical surface apply soap horizontally from side to side starting from the bottom to avoid streaking 2 Allow detergent to remain on the surface for a sho
10. aneously twisting the lance 90 clockwise It may help if you set the gun vertically on a flat surface with the lance pointing upwards 20 ENG
11. ckly Be thoroughly familiar with the ZN WARNING This unit was designed for specific applications It should not be modified and or used for any ee e controls application other than that which it was designed 4 Stay alert watch what you are doing NOTICE Always store your pressure 5 washer in a location where the temperature will not fall below 40 F 4 C freeze damage is not covered by Do not operate the product when fatigued or under the influence of alcohol or drugs the warranty 6 Keep operating area clear of all persons READ AND SAVE THESE 7 Do not overreach or stand on INSTRUCTIONS unstable support Keep good footing and balance at all times 8 Followthemaintenance instructions specified in the manual 4 ENG 10 Tt 12 13 14 15 16 17 18 19 20 21 This product is provided with a Ground Fault Circuit Interrupter built into the power cord plug If replacement of the plug or cord is needed use only identical replacement parts Do not touch plug or outlet with wet hands Avoid accidental starts Move Switch on unit to OFF position before connecting or disconnecting cord to electrical outlets Water spray must never be directed towards any electric wiring or directly towards the pressure washer machine itself or fatal electric shock may occur Never carry your pressure washer by the cord Do not pull on the cord to disconnect from the outlet
12. double insulated product nor should a means for grounding be added to the pressure washer Servicing a double insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the parts they replace A double insulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED The symbol above may also be marked on the product POWER SUPPLY AND ELECTRICAL INFO GROUND FAULT CIRCUIT INTERRUPTER PROTECTION The pressure washer is factory equipped with an electrical cord and a Ground Fault Circuit Interrupter GFCI power plug This cord should only be connected to an electrical outlet installed in accordance with local safety regulations NOTE The power supply must be 120 V 60 Hz and a minimum 15 amp dedicated circuit 6 ENG A Inspect cord before using Do not use if cord is damaged B Keep all connections dry and off the ground Do not touch plug with wet hands D The pressure washer is provided with a ground fault circuit interrupter built into the power plug If replacement of the plug or cord is needed use only identical replacement parts Contact customer service for proper replacement parts A WARNING Test GFCI before each use DO NOT use pressure washer if test below fails GFCI Test Procedures 1 Plug GFCI into power receptacle Indica
13. ease read the manual and pay attention to these symbols AN DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury ZAWARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury NOTICE Indicates a practice not related to personal injury which if not avoided may result in property damage CONSUMER SAFETY INFORMATION AN WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm In addition some cleaning products and dust contain chemicals know to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling IMPORTANT SAFETY INSTRUCTIONS N WARNING Please read this A WARNING When using this product entire manual before attempting basic precautions should always be to assemble operate or install the followed including the following product If you have any questions 4 Read all the instructions before regarding the product please contact using the product our customer service department at www power washer us or 2 To reduce the risk of injury do not 1 800 381 0999 operate near children or animals 3 Know how to stop the product and bleed pressures qui
14. ed in duration to one year on all components excluding the spray gun high pressure hose lance and ground fault circuit interrupter GFCI which are only covered for 90 days effective from the date of retail purchase and is not transferable This warranty excludes incidental consequential damages and failures due to misuse abuse or normal wear and tear This warranty applies only to products used in consumer home applications This warranty does not apply to commercial or rental applications This warranty gives you specific rights and you may also have other rights which vary from state to state 16 ENG TROUBLE SHOOTING GUIDE OPERATIONAL ISSUE POSSIBLE CAUSE SOLUTION Detergent is not dispensing Detergent is not pressure washer approved Use only detergents degreasers waxes and other cleaning solutions that are designed specifically for pressure washers Cleaners in this category will clearly state on the label that they are meant for use in pressure washers Do NOT use any other type of cleaning solution in your pressure washer Never use bleach ammonia any type of acid or hot water in your machine The suction tube has become disconnected clogged or kinked Ensure the clear suction tube is not damaged and is properly connected to the detergent nozzle Reconnect clean or replace the tube as needed Detergent nozzle is clogged with debris Clean the nozzle according to the ins
15. her cleaners Do not use bleach chlorine or any cleaners containing acids Always follow manufacturer s label recommendations for proper use of cleaners Always protect eyes skin and respiratory system from cleaners The pressure washer should not be used in areas where gas vapors may be present An electric spark could cause an explosion or fire To minimize the amount of water getting into the pressure washer the unit should be placed as far as possible from the cleaning site during operation To prevent accidental discharge the spray gun should be secured by locking the trigger when not in use To allow free air circulation the pressure washer should NOT be covered during operation Never touch grasp or attempt to cover a pinhole or similar water leak on the high pressure hose The stream of water IS under high pressure and WILL penetrate skin Use only hoses and accessories rated for pressure higher than your pressure washer s psi Never use with any other manufacturer s accessories or components 31 Never defeat the safety features of this product 32 Do not operate machine with missing broken or unauthorized parts 33 Never spray flammable liquids or use pressure washer in areas containing combustible dust liquid or vapors A WARNING Risk of injection or injury Do not direct discharge stream at persons SAVE THESE INSTRUCTIONS SAFETY FEATURES AUTOMATIC TOTAL STOP The pressure
16. ose from reel or hook if applicable Replace garden hose if necessary Water inlet Remove the filter screen O from the water filter screen inlet M and clean it thoroughly Replace the is clogged filter screen Extension cord We do not recommend the use of extension is too long or cords with your pressure washer If you wire gauge must use an extension cord verify that it is too small meets the minimum requirements listed in the Extension Cord paragraph under the Power Supply amp Electrical Info in this manual 18 ENG OPERATIONAL POSSIBLE SOLUTION ISSUE CAUSE No water Nozzle is Clean the nozzle according to the instructions coming out clogged provided in the Nozzle paragraph under of nozzle Maintenance section of this manual Water inlet Remove the filter screen O from the water filter screen inlet M and clean it thoroughly Replace the is clogged filter screen Kink in the Use a maximum garden hose length of garden hose 50 ft 15 2 m city water or 25 ft 7 5 m or hose is well water Ensure the garden hose is laid wrapped ona jout flat and does not have any kinks or storage wheel leaks Unwrap garden hose from reel or hook if applicable Replace garden hose if necessary Spray Gun Gun safety lock Release safety lock according to instructions Trigger will is engaged provided in the Starting paragraph under NOT Move Operation in this manual Unit will Unit is not Verify tha
17. perable 4 Turnthe machine OFF and squeeze the trigger to release the trapped pressure inside of the machine 5 Remove both the garden hose and high pressure hose from the unit 6 Disconnect the lance from the gun 7 Turn ON the machine and allow it to run for 5 seconds This will clear out most of the water trapped in the pump 8 Unplug machine 9 Wrap high pressure hose and power supply cord onto storage rack and snap power supply cord into place as shown Ss CX y 10 Store the machine and accessories in a dry climate controlled environment Do not store the machine or accessories in a place where the temperature could drop below 40 F 4 C ZA DANGER Risk of fluid injection When using replacement lances or guns with this pressure washer DO NOT use a lance and or lance gun combination that is shorter in length than what was provided with this pressure washer as measured from the nozzle end of the lance to the gun trigger NOTICE The use of any other accessory not recommended for use with this tool could be hazardous Use only accessories rated equal to or greater than the rating of the pressure washer 14 ENG SPECIFICATIONS Model 11BDE 210 PSI Max 1700 psi GPM Max 1 4 gpm Electrical Requirements 120V 15 A 60 Hz Electrical Cord 35 ft 10 6 m High Pressure Hose 23 ft 0 6 m Minimum Amp Source 15A Presure of Inle
18. r us or 1 800 381 0999 What is covered Replacement parts and labor Please note that we reserve the right to repair or replace the product as we deem appropriate What is not covered This warranty does not include such parts as nozzles which must be replaced as part of normal maintenance of the equipment rather than as the result of a defect Transportation charges to warranty center for defective products Transportation charges to consumer for repaired products Damages caused by abuse accident improper repair or failure to perform normal maintenance Use of improper chemicals or noncompliance with the operator manual s instructions Sales outside of the United States or Canada Any other expense including consequential damages incidental damages or incidental expenses including damage to property Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty does not cover damage resulting from failure to observe any of the following conditions 1 The inlet water pressure must be between 20 and 100 p s i 2 The inlet water temperature must not exceed 90 F 32 C 3 The unit should not be stored in areas where temperatures may drop below 40 F 4 C 15 ENG Implied Warranties Any implied warranties including the implied warranties of merchantability and fitness for a particular purpose are limit
19. re Inch The unit of measure for water pressure Also used for air pressure hydraulic pressure etc GPM Gallons Per Minute The unit of measure for the flow rate of water CU Cleaning Units GPM multiplied by PSI GPM x PSI CU Detergent Injection System Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness Water Supply All pressure washers must have a source of water The minimum requirements for a water supply are 20 psi and 5 gallons per minute If your water source is a well the garden hose length can only be 30 ft 9 m max AA WARNING To reduce the possibility of contamination always protect against backflow when connected to a potable water system A DANGER Risk of fluid injection and laceration When using the high pressure setting DO NOT allow the high pressure spray to come in contact with unprotected skin eyes or with any pets or animals Serious injury will occur e Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh which could result in amputation or other serious injury 9 ENG Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT See a physician immediately PRESSURE WASHER OPERATING FEATURES CLICK N CLEAN SPRAY LANCE Fig 4 AN WARNING Do not move the nozzle to adjust spray while the trigger is squeezed The
20. rt time before rinsing 3 Rinse with clean water under high pressure On a vertical surface first rinse from the bottom up then rinse from the top down Hold nozzle 6 8 in 15 20 cm from the work surface at a 45 angle using the flat spray as a peeling tool rather than a scrub brush NOTE Ensure that the detergent injection system is completely clean prior to switching from one detergent to another STARTING FIG 8 14 A DANGER Risk of injury from spray Always engage the trigger lock when gun is not in use Failure to do so could cause accidental spraying A WARNING Risk of Injury Do not direct discharge stream at self or others A WARNING Risk of unsafe operation Stand on a stable surface and grip gun spray wand firmly with both hands 11 ENG 1 Connect the high pressure hose E to the machine outlet K Ensure the threads are aligned properly and the connection is secure Se ISS 2 Connect the garden hose Y to the connector D on the front of the machine Before connecting run water through the garden hose not supplied to flush out any foreign matter NOTE If your water source is a well the garden hose length can only be 30 ft maximum Gei Insert the spray lance B R into the gun A by pushing firmly and simultaneously twisting a 1 4 of a turn counterclockwise until locked into place securely locked into place it could be ejec
21. rupter Protection paragraph under Power Supply amp Electrical Info in this manual To order a replacement GFCI or for GFCI installation instructions please contact our customer service department at www power washer us or by calling 1 800 381 0999 Spray gun Improperly Verify all components gun lance high lance or high connected pressure hose are properly connected pressure hose accessory according to instructions provided in this leaking water manual Leaking oil NOTE A small amount of leakage is normal water from If oil water leakage from pump is excessive pump please locate the specific source of the leak and contact our customer service department Contact our customer service department at www power washer us or 1 800 381 0999 NOTE Have the pressure washer present when calling with this issue Low surging pressure or motor does not stop when spray gun trigger is released NOTE The Pressure washer is NOT receiving a full volume of incoming water The machine requires a pressurized water source capable of sustaining a minimum of 20 psi at 5 gpm Faucet is not Verify incoming water supply faucet is open fully open at the maximum setting Garden hose Use a maximum garden hose length of is too long or 50 ft 15 2 m city water or 25 ft 7 5 m it is kinked well water Ensure the garden hose is laid restricted out flat and does not have any kinks or leaks Unwrap garden h
22. screen filter with warm water to clean e Replace screen filter and garden hose connector immediately to prevent any foreign matter from entering the pump N CAUTION Do not damage the screen filter while removing or cleaning Any foreign particles entering the pump may damage the pump 13 ENG COOLING SYSTEM The air vents located in and around the pressure washer must be kept clean and free of any obstructions to ensure proper air cooling of the motor during operation Z WARNING Prevent water from penetrating the vents of the pressure washer to minimize the risk of damage to the machine and to reduce the risk of shock to the operator STORAGE A CAUTION Prior to moving the unit always disconnect the garden hose via the garden hose connector CAUTION Always store your pressure washer in a location where the temperature will not fall below 40 F 4 C The pump in this machine is susceptible to permanent damage if frozen FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY END OF USE AND WINTER STORAGE INSTRUCTIONS 1 When finished using the pressure washer you must first drain and rinse the detergent tank 2 Run the pressure washer in low pressure until all of the soap is drained from the detergent tank 3 Pour clear water into the tank and run it through on low pressure as though it were detergent NOTICE Failure to clean properly will cause bottle or suction tube to become clogged and ino
23. t Water 20 100 psi Inlet Water cold tap Soap Consumption Rate 1096 max Water flow and maximum pressure ratings determined in accordance with PWMA standard PW101 SERVICE INFORMATION Do not return this product to your retailer Please contact our customer service department at www power washer us or 1 800 381 0999 LIMITED WARRANTY Limited Warranty This product is warranted against defects in material and workmanship for a period of one year on all components excluding the spray gun high pressure hose lances nozzles and ground fault circuit interrupter GFCI which are only covered for 90 days effective from the date of retail purchase and is not transferable This warranty excludes incidental consequential damages and failures due to misuse abuse or normal wear and tear This warranty applies only to products used in consumer home applications This warranty does not apply to commercial or rental applications This warranty gives you specific rights and you may also have other rights which vary from state to state Please complete and return the enclosed Customer Information Card Return of this card is not required to validate this warranty A store issued receipt or credit card statement showing the purchase date is an acceptable warranty validation Please retain one of these documents in your records If you have any questions please contact our customer service department at www power washe
24. t the On Off Switch l is fully NOT start turned ON engaged in the ON position NOTE Unit will only start and run when trigger GFCI Plug is Confirm the GFCI plug is reset and functioning not reset according to instructions provided in Ground is depressed and water is spraying Fault Circuit Interrupter Protection paragraph under Power Supply amp Electrical info in this manual Motor stops working during normal operation NOTE Motor s thermal overload switch is tripping because the motor is overheated Allow the motor to cool for 20 minutes before troubleshooting and the switch will automatically reset Extension cord We do not recommend the use of extension is too long or cords with your pressure washer If you wire gauge must use an extension cord verify that it is too small meets the minimum requirements listed in the Extension Cord paragraph under the Power Supply amp Electrical Info in this manual Nozzle is Clean the nozzle according to the instructions clogged provided in the Nozzle paragraph under Maintenance section of this manual Defective Turn unit OFF disconnect incoming water Spray Gun from unit and remove the gun and hose assembly Aim pressure washer away from the electrical outlet reconnect incoming water and switch the unit into the ON position If the motor starts and water flows steadily out of the front and you have verified that the nozzle is not clogged
25. ted under high pressure during operation possibly causing injury or damage 4 Turn incoming water on and fully open valve to insure maximum water flow to machine Plug GFCI C into power receptacle Firmly press and release the TEST button X then press and release the RESET button W The light on the GFCI should be illuminated M Ensure the gun safety is unlocked and squeeze the trigger until the air has escaped and a steady flow of low pressure water is coming from the nozzle NOTE The power supply must be 120 V 60 Hz and a minimum 15 de 12 ENG Turn switch to ON position I Note that the motor will momentarily start then stop 8 Squeeze the trigger to start motor and begin pressure washing NOTE The motor only runs when the gun trigger is depressed and water is spraying SHUTTING DOWN See Storage section in this manual for proper shutdown and storage procedures MAINTENANCE ZN WARNING Risk of burn hazard When performing maintenance you may be exposed to hot surfaces water pressure or moving parts that can cause serious injury or death To ensure efficient operation and longer life of your pressure washer a routine maintenance schedule should be prepared and followed If the pressure washer is used in unusual conditions such as high temperatures or dusty conditions more frequent maintenance checks will be required
26. tor light should illuminate 2 Press test button X Light should turn off 3 Press reset button W for use Indicator light should illuminate o Do not use if above test fails NOTE The GFCI must be reset each time the pressure washer is connected to an electrical outlet Reset by simply pushing the reset button on the GFCI power plug EXTENSION CORDS Use only extension cords that are intended for outdoor use These extension cords are identified by a marking Acceptable for use with outdoor appliances store indoors while not in use Use only extension cords having an electrical rating not less than the rating of the product Do not use damaged extension cords Examine extension cord before using and replace if damaged Do not abuse extension cord and do not yank on any cord to disconnect Keep cord away from heat and sharp edges Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord When using an extension cord observe the specification below Cable Length Wire Gauge Up to 25 ft 7 5 m 12 AWG Outdoor AN WARNING To reduce the risk of electrocution keep all connections dry and off the ground Do not touch plug with wet hands SAVE THESE INSTRUCTIONS 7 ENG GET TO KNOW THE PRESSURE WASHER 2 2 o 2 NOTE Photographs and line
27. tructions provided in the Nozzle paragraph under the Maintenance section of this manual The Click N Clean B spray lance is not in the Low Pressure Soap position Follow the instructions provided in the Using Detergent paragraph under the Operation Instructions section of this manual Detergent to Water ratio The pressure washer draws detergent at a maximum 10 1 water to detergent ratio Most pressure washer detergents are concentrated within this range If you feel you are using more detergent than is required for the application you can dilute the detergent with regular tap water Circuit breaker trips or fuse blown in fuse box Circuit overload Verify that the circuit is rated at 15 amps or greater Ensure no other appliance is drawing power from the same circuit dedicated circuit Extension cord too long or wire gauge too small Nozzle partially blocked We do not recommend the use of extension cords with your pressure washer If you must use an extension cord verify that it meets the minimum requirements listed in the Extension Cord paragraph under the Power Supply amp Electrical Info in this manual Clean the nozzle according to the instructions provided in the Nozzle paragraph under the Maintenance section of this manual 17 ENG OPERATIONAL POSSIBLE SOLUTION ISSUE CAUSE GFCI Plug For GFCI reset procedure see Ground fault Malfunction Circuit Inter
28. washer is equipped with a stop device which will sense when the trigger on the gun is released It will open the power circuit to the motor and cause the pressure washer to stop A WARNING If Automatic Total Stop fails to operate DO NOT USE THE MACHINE Contact our customer service department Further use wvill damage the machine and or cause personal injury ZA WARNING The pressure washer is also equipped with a main power ON OFF switch located on the unit It should always be moved to the OFF position when the pressure washer is not being used to prevent possible injury or damage MOTOR OVERLOAD The electric motor in this pressure washer is equipped with an overload protection device which will automatically shut off the motor in the event the motor draws excessive current or overheats The device will automatically reset itself and resume normal operation after a short period of time GROUND FAULT CIRCUIT INTERRUPTER PROTECTION This pressure washer is provided with a Ground Fault Circuit Interrupter GFCI built into the plug of the power supply cord This device provides additional protection from the risk of electric shock Should replacement of the plug or cord become necessary use only identical replacement parts that include GFCI protection SERVICING A DOUBLE INSULATED APPLIANCE In a double insulated product two systems of insulation are provided instead of grounding No grounding means is provided on a
Download Pdf Manuals
Related Search