USER MANUAL - Kramer Electronics
Contents
1. 5 1 Connecting to the VS 161H Using the RS 232 Connection 5 2 Connecting to the VS 161H Using Ethernet 6 Operating the VS 161H 16x1 HDMI Switcher 6 1 The PC and DVD Modes 6 2 Acquiring the EDID 6 3 Locking and Unlocking the Front Panel 6 4 Resetting the Device to Factory Default Values 6 5 Upgrading the Firmware 7 Technical Specifications 8 Default Communication Parameters 9 Kramer Protocol 2000 Figures Figure 1 VS 161H 16x1 HDMI Switcher Front and Rear Panels Figure 2 Connecting the VS 161H 16x1 HDMI Switcher Figure 3 Crossed Cable RS 232 Connection Figure 4 Straight Cable RS 232 Connection with a Null Modem Adapter Figure 5 Local Area Connection Properties Window Figure 6 Internet Protocol Version 4 Properties Window Figure 7 Internet Protocol Version 6 Properties Window Figure 8 Internet Protocol Properties Window ao oo NNNODOOOOCODMON OP WNHNDND N a oo Introduction Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 14 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROU2. a full connection of the D sub connector Because the null modem adapter which already includes the flow control jumpering described in Method A above only requires pins 2 3 and 5 to be connected you are free to decide whether to connect only these 3 pins or all 9 pins Null Mod Nutodem to PC Figure 4 Straight Cable RS 232 Connection with a Null Modem Adapter Connecting to the VS 161H Using Ethernet You can connect the VS 161H via the Ethernet using a crossover cable see Section 5 2 2 for direct connection to the PC or a straight through cable see Section 5 2 3 for connection via a network hub or network router After connecting the Ethernet port you have to install and configure your Ethernet Port For detailed instructions see the Ethernet Configuration FC 11 guide pdf file in the technical support section at http www kramerelectronics com VS 161H Connecting the VS 161H 16x1 HDMI Switcher 5 2 1 5 2 2 VS 161H Configuring the Ethernet Port After connecting the Ethernet port you have to install and configure it For detailed instructions on how to install and configure your Ethernet port see the Ethernet Configuration FC 11 guide pdf on our Web site at http www kramerelectronics com Connecting the Ethernet Port directly to a PC You can connect the Ethernet port of the VS 161H directly to the Ethernet port on your PC using a crossover cable with RJ 45 connectors This type o
3. recommended range OPERATING TEMPERATURE STORAGE TEMPERATURE HUMIDITY T CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload the circuit s When connecting the machine to the supply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for information For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine 0 to 40 C 32 to 104 F 40 to 70 C 40 to 158 F 10 to 90 RHL non condensing VS 161H Installing in a Rack To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the
4. requirements of your IT system 5 Click Properties The Internet Protocol Properties window relevant to your IT system appears as shown in Figure 6 or Figure 7 VS 161H Connecting the VS 161H 16x1 HDMI Switcher General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Use the following IP address IP address Subnet mask Default gate Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server El Validate settings upon exit Figure 6 Internet Protocol Version 4 Properties Window cen You can get IPv6 settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IPv6 settings Obtain an IPv6 address automatically Use the following IPv6 address IPv6 address Subnet prefix length Default gat yt Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server C Validate settings upon exit Figure 7 Internet Protocol Version 6 Properties Window VS 161H Connecting the VS 161H 16x1 HDMI Switcher ease 5 2 3 6 Select Use the following IP Address for stat
5. screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the rack rails and insert the proper screws not provided through each of the four holes in the rack ears Note In some models the front panel may feature built in rack ears Detachable rack ears can be removed for desktop use Always mount the machine in the rack before you attach any cables or connect the machine to the power If you are using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions available from our Web site 5 Connecting the VS 161H 16x1 HDMI Switcher Always switch off the power to each device before connecting it to your VS 161H After connecting your VS 161H connect its power and then switch on the power to each device HDMI Multimedia Player f J DVD Player a I HDMI Set Top Box Plasma Source DVD Player Display Figure 2 Connecting the VS 161H 16x1 HDMI Switcher Ea VS 161H Connecting the VS 161H 16x1 HDMI Switcher 5 1 To connect the VS 161H 16x1 HDMI Switcher as illustrated in the example in Figure 2 1 If required Set the appropriate INPUTS to the DVD PC mode Acquire the EDID 2 Connect the HDMI sources as follows A multimedia player to INPUT 1 A set top box to INPUT 2 A DVD player to INPUT 6 A DVD player to INPU
6. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and r
7. KRAMER ELECTRONICS LTD USER MANUAL MODEL Vs 161H 16x1 HDMI Switcher P N 2900 000665 Rev 4 Els E VS 161H Quick Start Guide This guide helps you install and use your product for the first time For more detailed information go to http Awww kramerelectronics com support product_downloads asp to download the latest manual or scan the QR code on the left Step 1 Check what s in the box The VS 161H 16x1 HDMI Switcher 1 Quick start guide IR remote control transmitter with batteries yf 1 Set of ear racks a Power cord 4 Rubber feet Step 2 Install the VS 161H To rack mount the machine attach both ear brackets to the machine by removing the three screws from each side of the machine and replacing those screws through the ear brackets or place the machine on a table Step 3 Connect inputs and outputs Step 4 Connect the power Connect AC power to the rear of the VS 161H switch on its power and then switch on the power on each device Step 5 Operate the VS 161H Acquire the EDID from Set the device to either the PC mode default or DVD o A connected output mode O The default EDID on an unconnected output Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 3 1 Defining the VS 161H 16x1 HDMI Switcher 4 Installing in a Rack 5 Connecting the VS 161H 16x1 HDMI Switcher
8. P 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Video Products GROUP 12 Digital Signage GROUP 13 Audio and GROUP 14 Collaboration Congratulations on purchasing your Kramer VS 161H 16x1 HDMI Switcher This product is ideal for e Conference room presentations e Rental and staging Note The Kramer VS 161H is identical to the VS 161HDMI just the name has changed by replacing the suffix HDMI by H according to the HDMI Guideline 2 1 2 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate i Go to http www kramerelectronics com support product_downloads asp Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cable
9. T 16 3 Connect the OUTPUT HDMI connector to an HDMI acceptor for example a plasma display 4 f required connect a PC and or controller to the RS 232 port and or the Ethernet port 5 Connect the power cord and power the device on Note The Mute button flashes if the EDID of the device connected to the output is different from the EDID which is currently stored Connecting to the VS 161H Using the RS 232 Connection You can connect to the unit via a crossed RS 232 connection using for example a PC A crossed cable or null modem is required as shown in method A and B respectively If a shielded cable is used connect the shield to pin 5 Method A Figure 3 Connect the RS 232 9 pin D sub port on the unit via a crossed cable only pin 2 to pin 3 pin 3 to pin 2 and pin 5 to pin 5 need be connected to the RS 232 9 pin D sub port on the PC Note There is no need to connect any other pins Connecting the VS 161H 16x1 HDMI Switcher 5 2 Figure 3 Crossed Cable RS 232 Connection Hardware flow control is not required for this unit In the rare case where a controller requires hardware flow control short pin 1 to 7 and 8 and pin 4 to 6 on the controller side Method B Figure 4 Connect the RS 232 9 pin D sub port on the unit via a straight flat cable to the null modem adapter and connect the null modem adapter to the RS 232 9 pin D sub port on the PC The straight cable usually contains all nine wires for
10. at are specific per input the PC mode default and the DVD mode e The PC mode is used when connecting a computer or several computers to one or more of the inputs via a DVI to HDMI converter cable for example the Kramer HDMI DVI Gold Plated Cable in various lengths This is the default mode e The DVD mode is used when connecting a DVD or several DVDs to the inputs When in the PC mode the input has access to the EDID default or acquired to prevent the computer from resetting if an output is not connected In the DVD mode the EDID of the connected output is available only when the input to which the DVD is connected is switched to the output The PC mode and the DVD mode can be applied to a single input or to several inputs For example if you want to connect a computer to INPUT 1 another computer to INPUT 2 and DVD machines to all the other inputs from INPUT 3 to INPUT 16 set INPUT 1 and INPUT 2 to the PC mode and all the other inputs to the DVD mode To set the inputs to either the PC or the DVD mode 1 Turn the power off rating the VS 161H 16x1 HDMI Switcher 6 2 2 Press the PANEL LOCK button while turning the POWER on again The INPUT buttons flash simultaneously 3 Keep pressing and holding the PANEL LOCK button for a few seconds and then release it The PANEL LOCK button flashes If an input button lights this indicates that that input is set to the DVD mode If no input button lights this indicates tha
11. eturn the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com Disconnect the unit from the power e supply before opening and servicing IMINO P N 2900 SAFETY WARNING Rev 4
12. f connection is recommended for identifying the VS 161H with the factory configured default IP address After connecting the VS 161H to the Ethernet port configure your PC as follows 1 Click Start gt Control Panel gt Network and Sharing Center 2 Click Change Adapter Settings 3 Highlight the network adapter you want to use to connect to the device and click Change settings of this connection The Local Area Connection Properties window for the selected network adapter appears as shown in Figure 5 Connecting the VS 161H 16x1 HDMI Switcher W Sharing Connect using Intel R 82579V Gigabit Network Connection This connection uses the following items o Client for Microsoft Networks E Microsoft Network Monitor 3 Driver Z QoS Packet Scheduler d2 File and Printer Sharing for Microsoft Networks E Intemet Protocol 6 4 Intemet Protocol Version 4 TCP IPv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Install Uninstall Properties Descripti TCP IP version 6 The latest version of the intemet protocol that provides communication across diverse interconnected networks K K K K K K K K Figure 5 Local Area Connection Properties Window 4 Highlight either Internet Protocol Version 6 TCP IPv6 or Internet Protocol Version 4 TCP IPv4 depending on the
13. ic IP addressing and fill in the details as shown in Figure 8 For TCP IPv4 you can use any IP address in the range 192 168 1 1 to 192 168 1 255 excluding 192 168 1 39 that is provided by your IT department General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 1 2 Subnet mask 255 255 255 0 Default gateway E Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit Figure 8 Internet Protocol Properties Window 7 Click OK 8 Click Close Connecting the Ethernet Port via a Network Hub You can connect the Ethernet port of the VS 161H to the Ethernet port on a network hub or using a straight through cable with RJ 45 connectors VS 161H Connecting the VS 161H 16x1 HDMI Switcher 6 1 Operating the VS 161H 16x1 HDMI Switcher This section describes e The PC and DVD modes see Section 6 1 e Acquiring the EDID see Section 6 2 e Locking and unlocking the front panel buttons see Section 6 3 e Resetting to the factory default values see Section 6 4 e Upgrading the firmware see Section 6 5 The PC and DVD Modes The VS 161H has two operation modes th
14. itcher for HDMI signals In particular the VS 161H features e Support for up to 1 65Gbps bandwidth per graphic channel Suitable for resolutions up to UXGA at 60Hz and for all HD resolutions e HDCP support High Definition Digital Content Protection e HDMI support HDMI V1 3 with Lip Sync and CEC e EDID PassThru that passes EDID HDCP signals from source to display e A Mute button to disconnect the output e A Panel Lock button to prevent unwanted tampering with the buttons on the front panel e Installation in 1U of a standard 19 professional rack enclosure You can control the VS 161H using the front panel buttons or remotely via e RS 232 RS 485 serial commands transmitted by a PC touch screen system or other serial controller e The Kramer RC IR3 infrared remote control transmitter e APC connected to the Ethernet port on the device via a LAN J94DUMS INAH HL9L SA 94 Hulu yad HLOL SA 3 1 Defining the VS 161H 16x1 HDMI Switcher Figure 1 defines the front and rear panels of the VS 161H 16x1 HDMI Switcher Figure 1 VS 161H 16x1 HDMI Switcher Front and Rear Panels l Feature l Function 6 INPUTHDMI Connectors si Connect to the HDMI sources from 1 to 16 7 8 9 7 Connect to a PC serial controller see Section 5 1 Installing in a Rack This section provides instructions for rack mounting the unit Before installing in a rack be sure that the environment is within the
15. its Similarly if a function is performed via the machine s keyboard then these bits are set with the INSTRUCTION NO which was performed The instruction codes are defined according to the table below INSTRUCTION NO is the value to be set for N5 NO 2nd BYTE Bit 7 Defined as 1 16 10 INPUT When switching ie instruction codes 1 and 2 the INPUT 7 bits is set as the input number which is to be switched Similarly if switching is done via the machine s front panel then these bits are set with the INPUT NUMBER which was switched For other operations these bits are defined according to the table 3rd BYTE Bit 7 Defined as 1 O6 00 OUTPUT When switching ie instruction codes 1 and 2 the OUTPUT 7 bits is set as the output number which is to be switched Similarly if switching is done via the machine s front panel then these bits are set with the OUTPUT NUMBER which was switched For other operations these bits are defined according to the table 4th BYTE Bit 7 Defined as 1 Bit 5 Don t care OVR Machine number override M4 MO MACHINE NUMBER Used to address machines in a system via their machine numbers When several machines are controlled from a single serial port they are usually configured together with each machine having an individual machine number If the OVR bit is set then all machine numbers accept implement the command and the addressed machine replies Fo
16. mer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a re
17. nt from the EDID which is currently stored 6 3 Locking and Unlocking the Front Panel To lock and unlock the front panel buttons 1 Press and hold the Panel Lock button until the button lights The front panel buttons are locked 2 Press and hold the Panel Lock button again until the button no longer lights The front panel buttons are unlocked 6 4 Resetting the Device to Factory Default Values To reset to factory default values 1 Turn the VS 161H off 2 Press and hold the Reset button on the rear panel while turning the device on 3 After approximately five seconds release the Reset button The device is reset to its factory default values see Section 6 4 6 5 Upgrading the Firmware For instructions on upgrading the firmware see Upgrading the VS 161H Firmware Using the K Upload Software 161H Operating the VS 161H 16x1 HDMI Switcher 7 ESS Technical Specifications NPUTS BANDWIDTH COMPLIANCE WITH HDMI STANDARD RESOLUTION POWER CONSUMPTION CONTROLS OPERATING TEMPERATURE STORAGE TEMPERATURE HUMIDITY DIMENSIONS WEIGHT INCLUDED ACCESSORIES OPTIONS 16 HDMI connectors 1 HDMI connector Supports up to 1 65Gbps bandwidth per graphic channel Supports HDMI and HDCP Up to UXGA 1080p 90 240VAC 50 60Hz 22VA RS 232 Ethernet 19 x7 x 1U W D H 2 5kg 5 5Ibs approx Power cord null modem adapter rack ears IR remote control Kramer HDMI cable
18. r a single machine controlled via the serial port always set M4 MO 1 and make sure that the machine itself is configured as MACHINE NUMBER 1 VS 161H Kramer Protocol 2000 S 161H Instruction Codes for Protocol 2000 Instruction Definition for Specific Instruction Description SWITCH VIDEO Set equal to video input which is toSet equal to video output which is to be switched be switched 0 disconnect 0 to all the outputs BO LOCK FRONT PANEL p Panel unlocked p R li Panel locked NOTES on the above table NOTE 2 These are bi directional definitions That is if the switcher receives the code it performs the instruction and if the instruction is performed due to a keystroke operation on the front panel then these codes are sent For example if the HEX code 01 85 88 83 was sent from the PC then the switcher machine 3 switches input 5 to output 8 If the user switched input 1 to output 7 via the front panel keypad then the switcher sends HEX codes 41 81 87 83 to the PC When the PC sends one of the commands in this group to the switcher then if the instruction is valid the switcher replies by sending to the PC the same four bytes that it was sent except for the first byte where the DESTINATION bit is set high NOTE 15 When the OVR bit 4th byte is set then the video commands have universal meaning For example instruction 1 SWITCH VIDEO cause
19. s for example the C HM HM series the C HM DM series and or our HDMI over fiber optics C FOHM FOHM series Specifications are subject to change without notice at http Awww kramerelectronics com VS 161H Technical Specifications 8 Default Communication Parameters RS 232 Protocol 2000 Baud Rate 9600 Data Bits Stop Bits E Parity Command Format Hex Example Output 1 to Input 1 0x01 0x81 0x81 0x81 Ethernet Default Settings Reset Settings IP Address 192 168 1 39 Power cycle the device while holding in the TCP Port 5000 Factory Reset button located on the rear panel of the unit UDP Port 50000 VS 161H Default Communication Parameters 9 Kramer Protocol 2000 The Kramer Protocol 2 000 RS 232 RS 485 communication uses four bytes of information as defined below All the values in the table are decimal unless otherwise stated MSB LSB 0 D N5 N4 N3 N2 N1 NO 7 6 5 4 3 2 1 0 1st byte INPUT 1 l6 15 l4 13 12 n lo 7 6 5 4 3 2 1 0 2nd byte 1 O6 05 04 03 02 01 o0 7 6 5 4 3 2 1 0 3rd byte 1 OVR X M4 M3 M2 M1 M0 7 6 5 4 3 2 1 0 4th byte 1st BYTE Bit 7 Defined as 0 D DESTINATION 0 for sending information to the switchers from the PC 1 for sending to the PC from the switcher N5 NO INSTRUCTION The function that is to be performed by the switcher s is defined by the INSTRUCTION 6 b
20. s all units including audio data etc to switch Similarly if a machine is in FOLLOW mode it performs any video instruction Kramer Protocol 2000 LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technolog
21. s in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer VS 161H away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the power cord that is supplied with the unit Warning Do not open the unit High voltages can cause electrical shock Servicing by qualified personnel only Warning Disconnect the power and unplug the unit from the wall before installing VS 161H Getting Started 2 3 Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at Attp www kramerelectronics com support recycling Overview The Kramer VS 161H is a high quality sw
22. t that input is set to the PC mode 4 Toggle between the PC mode input button not lit and the DVD mode input button lights by pressing that input 5 Press the PANEL LOCK button to exit this mode 6 You can connect a computer to the input s that is set to the PC mode and a DVD to the input s that is set to the DVD mode The following table summarizes the differences between the PC mode and the DVD mode PC Mode DVD Mode The input is connected to a The input is connected to a multimedia application such as a computer DVD a set top box and so on The EDID is available at all times The EDID is available only when that input is connected to an to prevent computer reset output The input EDID source is the The input EDID source is acquired directly from the connected default EDID or an acquired EDID output see Section 6 2 Acquiring the EDID The acquired EDID is used when an input is set to the PC mode To acquire the EDID 1 Turn the POWER off 2 Press the PANEL LOCK button and the INPUT 16 button while turning the POWER on again The INPUT buttons flash in sequence until the unit has completed reading the EDID 3 Release the PANEL LOCK and INPUT 16 buttons If an output was connected the output EDID is read to all the inputs If an output was not connected to the machine the default EDID is read to the inputs Note The Mute button flashes if the EDID of the device connected to the output is differe
23. turn authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product Ifitis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MER
24. y and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kra
Download Pdf Manuals
Related Search