User Manual
Contents
1. 34003109u1uk one gt remote OneRemote converter Type 34003109 User Manual Operate with Beolink Technisat DIGIT ISIO S Technisat DIGIT ISIO S2 Technisat Digicorder HD S3 Daily use using Beo4 Beo5 or Beo6 eo OK 4 NAV GD 1 Zur ck a 4 Page up v Page down im TV RADIO E Option EEN SFI Go WWW 1 As the un shifted function of the coloured function buttons has been assigned to other functions they have to be preceded witha to retrieve their actual coloured functions Green function Yellow function Red function Blue function Timer Operating using Beolink1000 The OneRemote converter is best operated using a remote control with coloured buttons like the Beo4 but can also be operated with a Beolink1000 The key on the old Beolink1000 remote control from Bang amp Olufsen has the same function asthe key on newer remote controls Thus all operations in the table above is doable using a Beolink1000 remote control Simply replace the inthe table with a The Beolink1000 remote control is equipped with a few buttons not available on newer models and the coloured keys has to be entered using a two key sequence one gt remote Playback and recording Play press 1 sec EMH Play alternative Stop D Still Rew FF M Timer EEN Record Other operations M Text local E Menu alternativ D info MENU Menu Special operations GS a v P P2. Control LED indications Continous red or green flashing When power is applied to the EXT controller the LED will start flashing The flash indicates that the EXT controller has not received a command data from the TV since power on As soon as a command is received from the TV the LED will stop flashing and light solid red or green If the control LED continues flashing after you have selected the source on the TV where the cable is attached the socket does not include control data or the TV has not been set up correctly Refer to the TV s user manual LED colour The EXT controller will light red when it has detected a device that is powered on It will either flash or light solid red The EXT controller will light green when it is not connected to a device or if it is connected to a device that is powered off If not connected to the TV output socket of a device the EXT controller will not be able to measure if the device is powered on and therefore always light green LED short flash off During use the LED will light red or green depending on the powerstatus of the device When receiving a controldata from the TV the control LED will shortly go out to indicate this If a button is pressed on the TV s remotecontrol supposed to operate the device and the LED does not indicate this the TV has not been correctly set up
3. ECHA 4 PIP STOP 2 Zoom STOP 3 HDMI xm Power manuel Exit Special Beolink1000 operations GOTO SERE JNNA EA PLAY STORE aN EA NAV Zur ck SFI WWW Green Yellow Blue Red one gt remote Congratulations The EXT controller from www oneremote dk can fully operate your device using your Bang amp Olufsen remote control terminal via a Bang amp Olufsen TV Beo4 BeoS or Beo6 remote controls can be used Beolink 1000 can be used with reduced functionality This guide explains how This EXT controller is ready for use plug amp play See the opposite page regarding daily operation Some operations can be altered to improve interaction with other controllers or to your convenience Refer to the installation section further on if changes are needed one gt remote EXT controller When a scart type connected source is selected with a Bang amp Olufsen remote control the B amp O TV starts to parse control data from the remote control to the attached device via the scart cable The OneRemote EXT controller captures these data and converts these into IR data that can operate the specific device The converted IR data is being transmitted via a small IR emitter that has to placed in front of the device to be controlled Here it emits the same IR data into the front of the device that it was made to receive from its own remote control As an EXT controller operates on data received via th
4. T controller can be programmed with different options to fit different set ups An option programming is done by pressing a series of buttons in a special scheme that does not occur during daily use A programming must be ended within 10 seconds To abort an ongoing programming sequence press any other button than or the numeric buttons EKE tommy Power off option In some cases it is not wanted that the device automatically powers off when the TV is powered off Use this option to enable or disable this SO GEC GEC EOJ ECJ ETC A Device never powers off aSr ECE GTC ECI ECJ EGC EEA EEE Device powers off with TV Menu option Some B amp O TVs not only echoes the MENU button from the remote control to the device attached to the Scart socket It also opens the TV s own ON screen menu Use this option to avoid that the device acts on this command if your setup has this conflict Saree EC EGC EC EGC EGO m EE Use the MENU button S0 EC EC EEC EGC EGC EE ignore the Menu button Zap mode option The zapmode option makes it possible to exchange the functions of the up amp down buttons with the blue amp yellow buttons The factory setting of programme zapping and up down arrows Programme zapping Moving up down in on screen menus While using a Beolink 1000 or other older remote control without coloured buttons it is a little awkward to make a programme zap when option 91 is set This option reverses the use of the sets of a
5. e scart cable it will function only when attached to a B amp O TV If both the B amp O TV and the device are equipped with DVI and or HDMI sockets a suitable cable can be added to improve the picture quality The EXT cable will still be needed for control data and maybe also the sound Refer to the user manuals for both the TV and the device about correct installation of HDMI DVI cables In a setup with link rooms all rooms will be able to operate the device via the link system With a OneRemote OneWay or TwoWay cable the device can be placed up to 25 metres away from the TV It could be placed in another room under a sofa or where ever it suits as operation is handled via the Scartcable If both the TV and the device are equipped with a HDMI connection a HDMI cable can be added to improve picture and sound quality one gt remote OneRemote operation in a B amp O system To be able to operate the device correctly with a B amp O remote control the user has to be familiar with operations with the original remote control as described in the device s user manual B amp O remote controls are not equipped with many keys so we have designed a layout that works logically even when shifting between different devices To get a common layout for many devices we therefore needed to redefine a few of the beo4 buttons to other functions Coloured buttons To make room for direct access to important functions we have moved the col
6. oured buttons to a lower layer To send a red button command must be pressed before the red button willsend the actual red command The same goes with the other 3 coloured buttons This way we are able to assign other functions to the coloured buttons when they are pressed directly In a OneRemote environment the coloured buttons is mostly assigned to these operations a Guide EPG or similar Back Backup Return or similar y D Programme zapping P P Channel up down or CH CH Programme stepping up down manoeuvring in menus Most set top boxes or TV s has 4 arrow buttons for moving up down left and right in on screen menus In addition they have separate programme stepping buttons for zapping through programmes B amp O remote control does not have separate buttons for programme zapping We therefore have chosen the blue and the yellow buttons to function as programme stepping buttons The four up down left and right buttons have been assigned for manoeuvring in on screen menus in our basic setup It is possible to use the up and down arrow for programme stepping refer to the installation section Go and Stop shifted operation Some of the buttons has two or three functions To get to these they have to be preceded with or The buttons that has been assigned secondary functions on this controller can be seen in the operating table on page 2 one gt remote Option programming The OneRemote EX
7. rrows one gt remote Some people find it more comfortable to use the up down arrows for programme zapping and therefore also benefits from this option using a Beo4 or BeoS keyed EC EC Evel ECOJ GCI E EE Yel ow Blue is programme Zap aSr EC Eke Eve EGC EGC E EE Uo Down is Programme Zap Installation troubleshooting The OneRemote EXT cable must be connected to the devices TV scart output socket and a scart input socket on the TV Then the IR emitter must be stuck in a way that it can emit IR light in to the devices IR receiver that normally receives the IR light emitted from the devices own remote control Only scart input sockets can be used that are able to send out linkdata to the EXT controller Also the TV must be programmed to send out data to the scart socket which is done in the TV s Sources menu Refer to the TV s user manual The EXT controller emulates DVD VMEM VTAPE SAT DTV VAUX and other sources There is no programming needed on the EXT controller The scartplug in that end of the EXT cable where the power supply and the IR emitter cable is attached MUST be inserted in to the devices TV output If not the EXT controller might not be able to power on and off the device correctly The EXT cable is equipped with a control LED build in to the scartplug that is inserted in to the device This LED assists in faultfinding if something is not operating correctly one gt remote
Download Pdf Manuals
Related Search