Manual - Amazon Web Services
Contents
1. ADJ Products LLC Every Flash Kling Batten has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during ship ping If the carton appears to be damaged carefully inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The Flash Kling Batten is a LED pixel panel for low resolution video displays This LED panel is controlled via Kling Net or Art Net Recommended control solutions Arkaos Media Master Express Media Master Pro and LED Master software s sold sepa rately Dynamic effects can be played on it which makes it a great system for night clubs Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning2. ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Follow Us On Junostraat 2 f t Mu 6468 EW Kerkrade Netherlands facebook com americandj service adjgroup eu www adj com twitter com americandj youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 99 4 15 User Instructions 2015 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe
3. Flash Kling Batten Daisy Chaining Units Do not daisy chain more than 50 Panels when connecting directly to a computer To daisy chain more than 50 Panels you must use a Eth ernet Switch When using a Ethernet Switch do not daisy chain more than 50 Panels from a single network port of the Ethernet Switch A maximum 2 output network ports of the Ethernet Switch can be used So the system can control 100 Panels maximum no more See the directions under the connection diagrams on page 6 Flash Kling Batten Daisy Chaining Units Kling Net Art Net_ Standard CAT Cable With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 12 fixtures maximum After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 5 Flash Kling Batten Connections JL Standard CAT Cable f 6 1 g 6 l Standard CAT Cable 7 i a E7 0 H Standard CAT Cable 0 O i B 6 f Standard CAT Cabl Standard CAT Cable Standard CAT Cable Kling Net Art Net Kling Net Art Net 1 2 3 When connecting you must use a CAT 5 Straight Network cable When connecting you must use a CAT 5 Straight Network cable Kling Net Art Net Standard CAT Cable 3 Maxi
4. To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 2 General Instructions Flash Kling Batten To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Features Flash Kling Batten CAT 5 Straight Network Cable included Kling Net and Art Net Compatible Recommended control solu tions Arkaos Media Master Express Media Master Pro and LED Master software s sold separately 160 x 0 164W SMD RGB LED s Flash Kling Batten Warranty Registration The Flash Kling Batten carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be freight pre paid and acc
5. e to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output Cleaning 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Flash Kling Batten Listed below are a few common problems the user may encounter with solutions Trouble Shooting No light output from the unit 1 Be sure the LED indicator on the back of the unit is on and in a solid state Unit is not receiving data 1 Check the LED indictator Same LED as the Power indicator If the LED is flashing you re a receiving data When moving your mouse arrow around in the grid the LED will flash if you are receiving data 2 Be sure you are using a CAT 5 Straight Network cable If problems are not resolved Contact ADJ for service 1 800 322 6337 ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 7 Flash Kling Batten Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required vo
6. ility to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180 day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 90 Day Limited Warranty e ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 8 Flash Kling Batten Locate the fuse holder at the end of the base opposite end of the eithernet connection Using a phillips head screwdriver remove the fuse holder Remove the used fuse and replace with a matching fuse Insert the fuse holder and fuse into the unit and secure the fuse holder Fuse Replacement Flash Kling Batten Du
7. lt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short e Disconnect from main power before making any type of connection e Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 7 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture
8. mum 2 output network ports of the Ethernet Switch can be used So the system can control 100pcs panels maximum n a E f o 0 Standard CAT Cable 0 a E 6 Standard CAT Cable 2 Do not daisy chain more than 50pcs LED panels from a single network port of the Ethernet Switch Installation method 2 g 9 Note Do not daisy chain more than 50pcs LED panels from the computer and use an Ethernet Switch if more than 50pcs LED lights are being controlled Note 1 The Ethernet Switch must be Gigabit Switch Installation method 1 ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 6
9. ompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ customer sup port for a R A number Flash Kling Batten DMX Workshop DMX WORKSHOP alternative software option to configure network settings DMxX Workshop is a fully featured network management analy sis configuration and diagnostics tool for Art Net networks It can be used to configure the Ethernet network settings on this fixture remotely such as the IP Address Subnet Mask and the DMX Uni verse This software application is Windows XP and Windows 7 compatible and is free of charge and available via download See link below http artisticlicence com index php mode products amp sub overview amp action amp product_id 351 ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 3 Flash Kling Batten Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is
10. parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inab
11. should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 4 Flash Kling Batten Operation Control Using Kling net or Art Net 1 Install one of the recommended operating softwares onto your computer Recommended softwares Arkaos Media Master Express Media Master Pro or LED Master Sold Separately Connect the panels via CAT 5 Straight Network cable When creating your own custom cable use RJ45 Straight Network cable Map the fixtures using KlingNetMapper or Art Net Mapper Control the fixtures using ArKaos or Art Net software Please refer to the media playback software user manual for further instruc tions Note ArKaos Kling Net requires a gigabit 1000 mbps Ethernet card and network router for a smoother operation N AW Connecting to Power and Data When connecting to power the LED indicator on the bottom of the unit should glow a solid red if the unit is receiving power When the unit is receiving a data signal the LED indicator will flash yellow Note The LED indicator may only flash when pressing the mouse and moving the indicator arrow around in the grid
12. sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective
13. unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank you Flash Kling Batten Specifications Model Flash Kling Batten SPECIFICATIONS LEDs 160 x 0 164W 3 in 1 LEDs Working Position Any safe working position Voltage 100V 240V 50 60Hz Power Draw 54W Full On Units Linked Together 50 Units Max Power Cord Daisy Chain 12 Units Max Beam Angle 120 Degrees Weight 7 27 bs 3 3 Kgs Dimensions 39 25 L x 4 W x 5 5 H 1000 L x 104 W x 140 H mm Warranty 2 Year 730 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 10 Flash Kling Batten Notes ADJ Products LLC www adj com Flash Kling Batten Instruction Manual Page 9 Flash Kling Batten Introduction Unpacking Thank you for purchasing the Flash Kling Batten by
Download Pdf Manuals
Related Search