IKON LED
Contents
1. Fax 823 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution This may cause eye damage Avoid looking directly into the light source Use sensible precaution Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE do not discard the shipping carton in the trash Please recycle when ever possible ADJ Products LLC www adj com Ikon LED User Manual Page 2 ikon LED Warranty Registration The Ikon LED carries a three year 1095 days limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ customer support for a R A number Ikon LED Precautions Safety Issue This unit may blow the fuse if the maximum allotted load of 2 amps is reached If the fuse needs replacement please see fuse replacement on page 5 Be sure the local power outlet match the required voltage of the unit Disconnect from main power before making any type of connection Do not remove the cover2. purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period sp
3. the speed Ikon LED Gobo Replacement The Ikon LED comes with a replaceable gobo This gobo can be inter changed at any time and allows you to customize your system To replace gobo 1 Unscrew the two screws located at the bottom that secure the gobo housing 2 Remove the gobo housing 3 Once the gobo housing has been removed remove the retaining ring that holds the gobo in This can easily be done using needle nose pliers Remove and replace the gobo with your desired replacement Reinsert the retainer ring and make sure the ring rests firmly against the gobo Slide the gobo assembly back into place and secure the housing with two screws amp on ADJ Products LLC www adj com Ikon LED User Manual Page 5 Ikon LED Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 4 fixtures maximum After 4 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures Ikon LED Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Fuse Replacement I
4. 5 13 User Instructions Ikon LED Introduction To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Unpacking Thank you for purchasing the Ikon LED by ADJ Products LLC Every Ikon LED has been thoroughly tested and has been shipped in perfect operat ing condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your unit for any damage and be sure all equipment necessary to operate the system has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return the unit to your dealer without first contacting customer support Customer Support ADJ Products LLC provides a toll free customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions For service related issue please con tact ADJ Products LLC Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337
5. Weight Gobos Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info adj com A D J Supply Europe B V Junostraat 2 te 6468 EW Kerkrade Netherlands service adj eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On facebook com americandj twitter com americandj youtube com adjlighting
6. e structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp Ikon LED Photometric Chart CUELA N lux25 4500 1000 456 268 172 lux32 C 3180 819 375 197 123 lux43 C 1930 459 212 134 87 Distance m 0 1 2 3 4 5 ADJ Products LLC www adj com Ikon LED User Manual Page 4 Ikon LED Remote Control This is an optional way to control this unit First you must link the remote control to the unit Do this by pressing the small code button located on the rear of the unit Press this button for 5 seconds until the green LED glows now press the Stand By button on the remote control If the unit blacksout the controller linked to the unit To erase the code press the code button for 3 seconds while the green LED is glowing do not press any buttons on the remote control Stand By Press this button to blackout the unit Up Dimmer Down Dimmer Press either of the buttons to adjust the output intensity Once you have pressed your disired button use buttons 0 7 to adjust the output intensity Up Rotate Down Rotate Press either of the buttons to adjust the rota tion speed Once you have pressed your disired button use buttons 0 7 to adjust
7. ecified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage dir
8. ect or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L ED Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Ikon LED User Manual Page 7 Ikon LED Specifications Model Ikon LED Voltage 100 240V 50 60Hz Power Consumption 83 6W Power Cord Daisy Chain 4 Fixtures Max LED 1 x 60W Colors White Beam Angle 25 32 or 43 Degrees Dimensions 9 5 L x 8 W x 8 5 H 236 x 227 x 215mm 8 Lbs 3 6 Kgs Size 54mm Viewable 33mm Fuse 7 Amp Duty Cycle None Warranty Three Year 1095 Days Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source
9. kon LED Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing Clean the external optics with glass cleaner and a soft cloth every 20 days Clean the internal optics with glass cleaner and a soft cloth every 30 60 days Always be sure to dry all parts completely before plugging the unit back in Cleaning N o Ikon LED No light output from the unit 1 Be sure the fuse has not popped The fuse is located on the rear panel Trouble Shooting ADJ Products LLC www adj com Ikon LED User Manual Page 6 Ikon LED Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of
10. s designed for mobile DJ s clubs bands roller rinks and any arena that requires a compact light weight easy to use unit This fixture is also suitable for theaters studios retail stores and other similar locations Power Supply The ADJ Ikon LED contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere Operation This fixture is designed to operate as a stand alone rotating gobo projector there is no need of a DMX controller It has been tested and there is no assembly necessary The Ikon LED is ready to be plugged in out of the box When this fixture is plugged in the unit will project the included gobo Using the bottom knob located at the back of the unit you can make the control the gobo rotation speed and rotation direction The top knob will let you control output intensity After plugging the unit if there is no LED output check the fuse If the fuse has not popped please contact customer support for further instructions This fixture features a light weight case design and an adjustable hanging bracket Ikon LED The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that th
11. under any conditions There are no user serviceable parts inside Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall To reduce the risk of electrical shock or fire do not expose this unit rain or moisture This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the fixture Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short The fixture should be serviced by qualified service personnel when A The power cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The fixture does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Ikon LED User Manual Page 3 ikon LED Operation Introduction The ADJ Ikon LED is a rotating gobo projector This fixture i
Download Pdf Manuals
Related Search