User`s manual
Contents
1. A amp o m 3 5mm audio in plug Connect to audio device W Getting started 1 Charging the receiver IKBTI2 comes with a built in rechargeable battery prior to using it it is recommended to charge the battery fully for the first time When the receiver is low power red LED flashes once and the receiver emits three tones every 20 seconds Please recharge the battery of the receiver Connect the charger to a standard power outlet and the charger plug to the charging jack of the receiver Red LED is on while charging It takes about 2 5 hours to charge the battery fully When charging has completed red LED will be off Remarks 1 If the receiver can t be turned off you can charge it to turn it off 2 Please don t attempt to take out the battery from the speaker as this might damage it e DESV Warning 1 The battery is recyclable 2 Batteries battery pack or batteries installed shall not be exposed to excessive heat place such as sunshine fire or the like 2 Turning on off the receiver Function Operation LED indicator Power on Press and hold MFB button for 3 5 seconds Blue LED is on for 1 second Power off Press and hold MFB button for 3 5 seconds Red LED is on for 1 second 3 Pairing with Bluetooth devices How to enter pairing mode Function Operation LED Indication tone indicator Enter pairing mode Ensure the receiver is turned off LED Two DU tones2. 5 After successful pairing and connecting blue LED of the receiver will flash twice quickly every 5 seconds Remarks The pairing password of the receiver is 0000 So the receiver can only pair with a Bluetooth transmitter whose pairing password is 0000 If pairing still fails after several tries please refer to the Bluetooth transmitter s user s manual for further information 4 4 Music playback Connect IKBT12 to an speaker and a Bluetooth music device at the same time now you can enjoy music wirelessly Speakers e to Pura with 3 5mm audio in jack Function Status of IKBT12 Operation Pause Playing music Short press MFB button once Play Pausing Short press MFB button once Remarks The music will automatically pause when you dial a phone number or there is an incoming call IKBTI2 hasn t a microphone so you need to switch the call to the mobile phone The music will automatically play when the call is ended 5 LED indicator LED indicator Status of IKBT12 LED flashes red and blue alternately Pairing mode Blue LED flashes once every 2 seconds Standby mode and not connected Blue LED flashes twice every 5 seconds Connected Red LED flashes once every 20 seconds Low power Care and maintenance Read the following recommendations before using the receiver Following these you will be able to enjoy the pr
3. 1 Bluetooth profiles A2DP and AVRCP Bluetooth frequency range 2 402GHz 2 480GHz Operating distance 10 meters Class II Charging input voltage current DC 5V 300mA Standby time 230 hours Working time Up to 12 hours Dimensions 45x33x8mm Weight 14g Notes 1 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
4. other they will no need to re pair next time Every time the receiver is turned on it will automatically connect to last connected device If you want to pair it with other devices please turn off the Bluetooth function of last connected devices first and pair the receiver with the new device according to steps 1 6 mentioned above When the reveiver is turned on and doesn t connect to any devices press MFB button twice it will automatically connect to the last connected device When the receiver and the mobile phone are out of effective range to disconnected they can connect to each other automatically once going back to effective range If the Bluetooth version of your mobile phone is V2 1 or above it will no need to enter PIN No when the receiver pairs with the mobile phone Pairing with Bluetooth transmitter You can connect the receiver with a Bluetooth transmitter to enjoy music wirelessly Hereby take BTTO10 Bluetooth transmitter for iPod not included for example The pairing procedures are as follows 1 Place the receiver and the Bluetooth transmitter where they are easily viewable by no more than meter apart 2 Enter the receiver s pairing mode Please refer to How to enter pairing mode 3 Turn on the Bluetooth transmitter It will automatically search for Bluetooth devices and send a pairing request 4 When the receiver requests to enter a PIN No the transmitter will response 0000 automatically
5. ikross User s manual IKBT12 Bluetooth Stereo Music Audio Receiver B Before Use sisiocsscavsscecivocssctsescocesessseusocsncesesdoasisosscedessaeseesscsescosactseosseveuses 1 1 About IKBT12 M 2 System requitements isses estesa ee UERTRERARTRM PESE Y PRG s Hes janes Pa ISE ex 1 3 Overview Of IKBT 12 rice cadnndinssiteecadeadnerivaaasesenassduivisbesnseantadsdaanastyabeesens 1 E Gettin Started 1 Charging the receiver 2 Turning on off the TECOIVER iiie rasoirs ets xe eire t es oae deua steaevedeess eadssngane iei 2 3 Pairing with Bluetooth devices 3 4 Music playback 5 FUB Db MEN 5 Welcome to use this Bluetooth stereo receiver IKROSS IKBT12 Please read this user s manual carefully before use W Before use 1 About IKBT12 IKBTI2 is a stereo Bluetooth receiver You can use an common audio device with 3 5mm audio in jack for playing back any stereo Bluetooth enabled device s music after plugging in IKBT12 The product comes with a built in rechargeable battery it can be usded for about 12 hours after being charged fully 2 System requirements Audio device with 3 5mm audio in jack such as speakers radios etc Bluetooth transmitting device supporting A2DP profile such as Bluetooth mobile phones Bluetooth MP3s etc 3 Overview of IKBT12 MFB button Power on off pair music pause play Charging jack DC 5V LED indicator Indicate current status
6. oduct for many years Do not expose the receiver to liquid moisture or humidity to avoid the product s internal circuit being affected Don t use abrasive cleaning solvents to clean the receiver Do not expose the receiver to extremely high or low temperature as this will shorten the life of electronic devices destroy the battery or distort certain plastic parts Don t dispose of the receiver in a fire as it will result in an explosion Don t bring the receiver into contact with sharp objects as this will cause scratches and damages Don t let the receiver fall down onto the floor The internal circuit might get damaged Don t attempt to disassemble the receiver as it may get damaged if you are not professional If you do not plan to use the receiver for a long time please store it in a dry place that is free from extreme temperatures and dust In case the receiver doesn t function properly send it to the store you bought it The staff will help you to solve the problem 1 2 FAQs What to do when IKBT12 can t be turned on Please charge the IKBT12 What to do when BTR001 can t pair and connect to a Bluetooth device a Make sure the Bluetooth device is placed within 5 meters b Ensure IKBT12 has entered pairing mode 3 What to do when IKBT12 can t be turned off Please charge the IKBTI2 for about 2 seconds 6 W Specifications Bluetooth version Bluetooth V2
7. otherwise turn it off first and flashes red then press and hold MFB button and blue for 6 7 seconds until LED alternately flashes red and blue alternately Remark The pairing mode will last 2 minutes the receiver IKBT12 will switch to standby mode automatically if no devices can be connected within 2 minutes Pairing with Bluetooth mobile phone Ensure your mobile phone supports A2DP profile The pairing procedures will vary depending on different models of mobile phones Please refer to your mobile phone user s manual for further information The general pairing procedures are as follows 1 Place the receiver and Bluetooth mobile phone where they are easily viewable by no more than meter apart 2 Enter the receiver s pairing mode please refer to How to enter pairing mode 3 Activate your mobile phone s Bluetooth function and set your mobile phone to search for Bluetooth devices within range and select ikross from the list of devices shown 4 According to the indication enter password or PIN No 0000 5 If prompted by your mobile phone to connect select Yes This will vary among mobile phone models 6 After successful connecting blue LED flashes twice quickly every 5 seconds Remarks If no devices can be connected within 5 minutes the receiver will then turn off automatically in order to save power After successful pairing the receiver and the mobile phone will remember each
Download Pdf Manuals
Related Search