MCC201/MCC201H User manual, 59300507, Rev002
Contents
1. Privilege Allowed Operations Remarks Admin All operations User ID admin Manager All operations except for user configuration User Live viewing and PTZ control Guest Live viewing only e Add User Press Add button The following window will appear Add User 1D Password Privilege Level Manager v Enter User ID and password Up to 15 characters and select Privilege Level MCC201 MCC201H User manual 4 Remote Configuration e 49 e Delete User Select the User to be deleted and press Delete button e Change Password Press Modify Password button The following window will appear Modify Password Madity Cancel j Enter the current password and then set a new password e Modify Privilege Level Press Modify Privilege button to change User level It is not allowed to change the privilege level of admin user Modify Privilege Level Modity Cancel Login Policy Authentication Type HTTP authentication based on RFC 2617 HTTP Authentication Basic and Digest Access Authentication is supported e Skip Login provides for convenient access to the server when authentication is not required When Skip Login is set to Enable login step is skipped The privilege level after login in this way is determined by the setting of Privilege Level after Login Skipped 50 e 4 Remote Configuration MCC201 MCC201H User manual 5 Decoder Configuration The unit can be also configured to a deco2. One way Streaming This encoder provides two kinds of one way unidirectional streaming based on UDP to clients RTP and MPEG TS Both are a kind of broadcasting where traffic from client to server is not generated at all RTP Real Time Transport Protocol is an Internet protocol used for transmitting single real time multimedia data such as audio and video to a select group of connected clients Normally RTSP uses RTP to format packets of multimedia content RTP menu is used when the RTP only streaming without RTSP connection RTP stream will be transmitted to the destination set The SDP Session Description Protocol file can be found in the server and a client can retrieve it using http connection Related settings are as follows Destination IP Set the IP Address of the destination system which will receive RTP stream If the system is decoder RTSP authentication information can be entered in the middle of RTSP URL as follows risp admin 12340192 168 10 100 554 video1 Destination Port Set the Port of the destination system which will receive RTP stream User Name Enter the User name that will be used as session name in the SDP file File Name Enter the file name that will be used as the name of the SDP file Then it can be accessed through http ServerAddress filename Mode RTP Destination IP 192 168 10 14 Destination Port 1026 0 1026 65534 Even number only User Name Office File Name ch0 sdp e MPEG TS
3. Sensor Beep Dalarmi LlAlarm2 Sensor2 Beep LlAlarm1 O Alarm2 Sensor Beep LlAlarm1 C Alarm2 Sensor4 lBeep Dalarmi Dalarm2 On Video Loss Beep Dalarmi L Alarm2 On Motion Beep Dalarm1 O Alarm2 On Disconnect On Disconnect Beep LlAlarm1 O Alarm2 Duration Beep synchronous E Alarm1 1sec KA Alarm2 1sec E The event configuration configures the actions for each event type Local section configures the actions for events from local self Decoder system and configuration activates local devices and Remote sections configures the actions for events from remote Encoder or IP Camera system The following table lists the possible actions for events Action Description Beep Outputs beep sound using the buzzer in the system Alarm1 Alarm2 Triggers alarm relay port E mail Sends E mail to the specified address AVI file can be attached FTP Upload AVI file to a specified FTP server Preset Moves the PTZ to associated preset position Sensori Sensor2 Configure the actions when the sensor 1 or 2 is activated Multiple actions can be set for a single event On Video Loss Configure the actions when video input signal is lost Multiple actions can be set for a single event MCC201 MCC201H User manual 5 Decoder Configuration e 55 e On Motion Configure the actions when motion is detected Multiple actions can be set for a single event e On Disconnect C
4. 2 Bl a B a EN E SAT SPEER Live View User 34 e A Remote Configuration MCC201 MCC201H User manual Serial Port Configuration Serial Protocol Two COM ports are available at MCC201 and MCC201H RS 232 and RS 422 485 See more information in appendix 6 e g wiring details Serial Port Configuration The serial ports can be configured as follows Note Each of the serial ports confiqurations must be same as the connecting device Mode Selection Bitrate 2400 4800 9600 19200 38400 57600 115200 bps Data Bits 5 6 7 8 bits Parity NONE EVEN ODD bit Stop Bit 1 2 bit PTZ PTZ Type Select the type of PTZ camera or receiver PTZID Since it is possible to control multiple PTZ cameras or receivers over single control line each camera or receiver will be assigned with unique ID Enter PTZ ID of a camera or receiver for control The ID value range can be between 0 and 255 PTZ Port Select the serial port used for PTZ camera control Sensor Type There are two sensor input ports on MCC201 Each of the sensor ports can be configured to the following Function Operation OFF Not used NO Normally Open The port is normally open and activated when closed NC Normally Closed The port is normally closed and activated when opened The function of the sensor port is set based on the type of the sensor connected MCC201 MCC201H User ma
5. 2500 kbps 32 10240 12 a High Profile Y O op O on O H264 9 MJPEG v 720x576 Scaling 5 VBR v v v Fine Use Motion Detection of O On ANSIOSO DORIA Edit O Enable Mode Set Disable Erase Apply Edited Area Sensitivity 0 for most sensitive Information Display SystemID Time Position Burnin OSD SystemID Time Position Font Size Color Brightness Contrast Hue Saturation Output Format Output Format a O op O on O off on Bottom O Top O of O on O op O on O Bottom Top O Small 8x8 O Middle 16x16 O Large 32x32 45 a 43 a 50 a 50 a PAL 720x576 v MCC201 MCC201H User manual 4 Remote Configuration Encode Note Some of the features are not available until the unit is connected to video signal Input Format Select the desired video input format according to the video source When in encoder mode the MCC201 supports analogue composite video PAL amp NTSC but also digital HDMI and HD SDI signals For the digital signals the dropdown menu is containing a selection of supported video resolutions Note MCC201H supports only HDMI and analogue video formats Input Deinterlace When operating with interlaced analogue video the deinterlacing function can set either ON or OFF Resolution Select video encoding
6. DAlarm1 L1Beep DAlarm1 Beep DAlarmi DAlarm2 C E mail synchronous 1sec S 1sec 25 25 465 1025 65535 Got OOn O Disable O Enable Preset Cem Clem Cem Clem Clem Clem Cem FTP Clem Hooda pog O 1 1 10 21 21 1025 65535 O Primary Video O Secondary Video O JPEG Capture 1 1 10 of O On 10 sec Max 300 300 sec Max 3600 s E i u No Preset No Preset No Preset No Preset No Preset v No Preset No Preset vw z Es ij e El 8 d No Preset v off O Primary Video O Secondary Video O JPEG Capture MCC201 MCC201H User manual 4 Remote Configuration This product has two sensor ports and two alarm ports When a decoder instead of a PC client is connected to encoder one system becomes a Local system and the other as a Remote system in general a system which is being used by the user is called as Local system Then actions for events can be configured for events from the remote system as well as for local system For example it is possible to turn on an alarm device in local center decoder system when a sensor device in remote end site encoder is triggered Local section configures the actions for events from local self system and configuration activates local devices and Remote sections configure the actions for events from remote peer system The following table lists the pos
7. Input port of video encoder accordingly Note HD SDI not available on MCC201H Connecting with Analogue Camera Connect a camera to the encoder BNC video Input port Decoder System Connect a monitor to HDMI or COMPOSITE BNC output of the decoder Connecting Audio Audio is full duplex It is possible to set the mode as Tx only Rx only or Tx Rx Connect audio input and output ports to audio devices accordingly e The Audio signal required is line level so audio equipment with an amp mixer or other amplifier should be used Connecting Serial Ports For camera control PTZ controller keyboard and receiver can be connected to serial ports Two corresponding serial ports in encoder and decoder which are connected in connected in 1 to 1 fashion works in pass through mode This means that commands at a local system s COM1 port will be transparently passed to the remote system s COM1 port Also a command at a local system COM2 port will pass to the remote system s COM2 port Connecting Sensor and Alarm Connect sensor and alarm devices to corresponding terminals accordingly Connecting Power After confirming the power source connect power adaptor and connect the 12VDC connector to the system 8 e 2 Installation MCC201 MCC201H User manual Check the system start up Once the power is supplied to the camera it will start booting The system will boot up to an operating mode after approximately 40 60 seconds Th
8. a secondary video stream The secondary video can be viewed on Live View window by selecting Secondary on Video selection Dual Encode Algorithm Select H 264 or MJPEG for the secondary streaming Both CBR and VBR modes are available However the MJPEG is supported only by the VBR mode and hence the video quality level needs to be assigned MCC201 MCC201H User manual 4 Remote Configuration e 23 Motion Detection Use Motion Detection Determine to use Motion Detection function e Motion Detection Area Editing Configure regions for motion detection Regions of arbitrary shape can be configured by the following steps 1 Select Enable on Edit tab 2 Select editing Mode Set is for including cells to motion detection region and Erase is for excluding 3 Select cells using the right button of the mouse Multiple cells can be selected conveniently by press and dragging 4 Press Apply Edited Area to save the editing Motion Detection Use Motion Detection O Off 9 On H c cni mi m m ml 14 F mI 4 J 4 IS H EE B 1063 HI BE E mE El B m BH l E i l E BEEEEEER EP ILL EEN E BEBHBBHEB Edit O Enable Disable Mode O Set O Erase Sensitivity D for most sensitive cx z 5 Sensitivity Sensitivity is the condition to trigger an event of motion detection The value determines the sensitivity of the motion detection within a block the smaller the more sensitive It is sele
9. new folder Enter the file name on Filename field 2 Press Start button to start to record EA 3 Press Stop button to stop to record Folder P 1_storag 4 AVI file named IP address hh mm ss or File name IP Filename Cross Road address hh mm ss will be generated in the specified folder depending on MN whether the path specified a folder or a prefix of the file name Display Buffer 1 e Display Buffer Set the number of video frames to be buffered before being displayed on web browser Larger value results in smoother video by sacrificing the latency A setting of 10 15 frames can be used generally for most situations 14 e 3 System Operation MCC201 MCC201H User manual Initialization of IP address If needed the IP address of the device can be restored to factory default values by using the reset button on the rear side of the MCC device 1 While system is in operation press the reset button for more than 5 seconds 2 The device shall reboot see the led indicators 3 Once the device has completed the reboot and has restarted the default IP address settings are as follows e IP mode Fixed IP e IP address 192 168 10 100 e Subnet mask 255 255 255 0 e Gateway 192 168 10 1 e Base port 2222 e HTTP port 80 MCC201 MCC201H User manual 3 System Operation 15 4 Remote Configuration Remote setting is available by using web browser Enter IP address of camera and then a live vie
10. operation If a different port is configured in the SMTP server this port needs to be changed accordingly Sender Address Enter an account registered in the SMTP server A Authentication on SMTP server Specify if the E mail server requires authentication for E mail sending 1D amp password When the server requires authentication ID and Password of an E mail account need to be entered Destination address Enter Destination address More than one address can be entered by delimiting comma or semi colon Destination address can take up to 63 characters Video Clip Attaching Video clip stored at the moment of event can be attached as an AVI or JPEG file format When dual encoding is enabled Primary video Secondary video H 264 only or JPEG Capture can be selected The duration of video clip can be configured with Pre Event Time and Post Event Time in Event Record section Number of Frame The number of JPEG frames is configured This setting is applicable only when JPEG Capture is selected A E mail Test E mail sending can be tested with this button Please note that configured settings should be saved first by pressing Apply button before using E mail Test function One of the following messages will come as a result of the test Message Description E mail sent successfully Test E mail has been sent successfully Reception in the client can be checked Failed to connect SMTP se
11. resolution Scaling option is used when encoding resolution is different from input resolution Without scaling option the input video is cropped according to defined encoding resolution If scaling is enabled the input video is adjusted to match the encoding resolution Framerate Determine the maximum number of frames per second for the video stream 1 2 3 4 5 6 8 10 15 20 25 and 30 60 frame rate can be selected Preference Available video bit rate controls are CBR for constant bit rate and VBR for variable bit rate CBR mode presents a fixed bit rate defined for the video stream in the network The user must define a fixed value on the bitrate field VBR mode presents a variable bit rate and corresponds the changes on the video content When VBR mode is selected the user have to define the desired video quality level not bitrate Quality Select the video quality level for the VBR mode Available levels are Ultra fine Very fine Fine Normal Below normal Economy Poor and Very poor Quality mode VBR encoding tries to encode every frame in a constant quality Therefore resulting bitrate may vary a lot depending on the complexity or activity changes in the input video It is preferred when constant video quality is required and network bandwidth is enough for delivering the stream of highly varying bitrate 22 e 4 Remote Configuration MCC201 MCC201H User manual e Bitrate Determine bitrate value be
12. the firmware upgrade Be patient the process may take several minutes Version Enc V1 102D 001 Board ID 47 Now Downloading Please wait Upgrade D cckskim update_fwihvsSys102C_ Browse Now Upgrading Please wait a minute 18 4 Remote Configuration MCC201 MCC201H User manual Config Backup and Restore e Backup All the device settings can be stored into a backup file for a later use such as recovery or setting a spare part unit Restore Stored configuration can be browsed and restored The server is rebooted once Config Restore button is pressed Time e Start Time Displays the date and time for the last system startup e Current Time Current date and time Enter a new date and time and press Set Current Time button to update date and time Time Format Change the time format Selectable time formats are as below YYYY MM DD hh mm ss Ex 2010 4 11 18 18 42 DD MM YYYY hh mm ss Ex 11 4 2010 18 18 42 MM DD YYYY hh mm ss Ex 4 11 2010 18 18 42 e Time Zone Select the desired time zone for the system Depending on the time zone Daylight Saving Time will work automatically A time zone is a region of the earth that has uniform standard time usually referred to as the local time By convention time zones compute their local time as an offset from UTC Coordinated Universal Time In casual use GMT Greenwich Mean Time can be considered equivalent to UTC Local tim
13. the further configuration of the device is not prohibited and all other device settings are available in a normal fashion Live View controls TELESTE Live View Setup Video Select MCC201 Primary O Secondary Vies SES TELESTE 20 00 2008 10880842 O 50 10096 Full Screen Digital Zoom PTZ Control MEC201 gl Ze Sensor input 7 Q Alarm output Q Q Snapshot Talk dor Oon File Record Folder Filename Start Display Buffer 1 12 e 3 System Operation MCC201 MCC201H User manual e Video Select Select the Video stream to be viewed Primary or Secondary This camera is capable of dual streaming primary streaming and secondary streaming Video will be displayed according to the resolution set on video configuration If dual streaming Use Dual Encode Menu in Video page is not activated secondary video is not available e View Size Adjust the Screen size Screen size is initially adjusted according to the compression resolution If you click 5096 icon the whole screen size will be reduced to half size e Digital Zoom Digital Zoom ai c Control the Digital zoom on the screen The more the camera zooms in the smaller the square of control panel is il gt Position of the image can be changed by moving position of the square E W a If you press x1 the screen will return to the normal size e PTZ Control Optical Zoom amp Digital zo
14. too small to display OSD text in large text Output Format When in encoder mode the input video signal is available for local monitoring and previewing either on the composite video output BNC out or on the digital output HDMI out Note The preview video is captured before entering the encoding engine of the device Select the output format for the monitor preview according to the video output and monitor specification The available preview modes are e NTSC 720 x 480 e PAL 720 x 576 e 720p60 1280 x 720 e 1080i60 1920 x 1080 e 720p50 1280 x 720 e 1080 50 1920 x 1080 e 1080i59 94 1920 x 1080 e 720p59 94 1280 x 720 e 1080p30 1920 x 1080 MCC201 MCC201H User manual 4 Remote Configuration e 25 Audio Configuration Setup System Video Audio Network Serial Event Audio Algorithm Algorithm 9 G 711 OAAC Mode Mode Tx amp Rx Y Input Gain Input Gain Audio Output Audio Output 9 Decoded Audio O Loopback Algorithm Algorithm Select the audio algorithm G 711 or AAC Live View Preset Record User Apply 25 G 711 and AAC from client to server direction are supported Thus bidirectional audio communication is supported e Bitrate Select the bitrate between 64Kbps and 128kbps when AAC is selected The sampling rate is fixed to 8KHz and 32KHz for G 711 and AAC respectively Note When two MCC units are connected together encoder decoder the audio settings should
15. 01H User manual System Connections MCC201 operates as one of two modes as Encoder or Decoder MCC201 systems can be connected in either 1 to 1 fashion where one encoder is connected one decoder or 1 to many fashion where one encoder connected to many decoders Following chart shows data status of video audio and serial data on each mode System Mode Video Audio Serial Data Encoder Transmit Transmit Receive Transmit Receive Decoder Receive Transmit Receive Transmit Receive Therefore the system modes are defined by the video communication and all system modes are capable of bi directional transmission of audio or serial data Topology Generally the encoder and a decoder are connected in 1 to 1 mode To support specific situation 1 to multiple connection is also supported 1 1 Connection Unidirectional Transmission Site Remote Center The most commonly used configuration is 1 to 1 connection An encoder is installed at a site where video images can be transmitted and a decoder is installed at a center location to receive and view the video images on monitors Audio and serial data are transferred in either direction A decoder and encoder can be connected by setting the encoder s address at the decoder s remote IP MCC201 MCC201H User manual 1 Introduction e 5 e 1 N Connection Unidirectional Transmission Site Remote Center In this configuration a site can be moni
16. 35 Set the SNMP Trap Destination Port SNMP is not used by setting O value Multicast e Multicast IP The Multicast menu is used for configuring the multicast IP address to which media stream is delivered when a client such as a Decoder VMS or NVR software is connected in multicast mode The multicast IP address selection range is between 224 0 0 0 and 239 255 255 255 The selection can be used only when media protocol is set to Multicast DDNS Recommended setting is none Check IP Disable If Check IP Disable is selected it will skip to check its own IP In Fixed IP mode the set IP will be registered on DDNS server In DHCP mode dynamically assigned IP will be registered on DDNS server Normally Check IP Disable should be unchecked in order to obtain public IP in the network 32 4 Remote Configuration MCC201 MCC201H User manual Bitrate control When there are more than one client connected to the camera due to bandwidth difference among the clients some of them do not have enough bandwidth to receive encoded stream completely In this case it is possible to select the way to stream video to clients as following Frame Drop Mode Encoding is performed strictly according to video settings When a client is connected through a network with less bandwidth it may not receive all the frames That is frames are dropped on sending module if the network is bottlenecked Suppression Mode Encoding bitrate and frame rate
17. Authentication of O On One way Streaming Mode Off ba SNMP SNMP Listen port 161 0 161 102565535 SNMP Trap Destination IP 0 0 0 0 SNMP Trap Destination Port 162 0 162 102565535 Multicast Multicast IP 224 10 0 0 224 0 0 0 239 255 255 255 DDNS DDNS Server 9 None O TrueDNS O DynDNS O Vdyn O Check IP Disable Bitrate Control Flow Control Mode Frame Drop Mode E IP Filtering Setup IP Filtering Setup Address Information Current IP 192 168 26 30 Current Domain Not RegisteredB MAC Address 00 1C 63 A6 11 11 Connecting 28 e 4 Remote Configuration MCC201 MCC201H User manual Local e IP mode Select the IP mode Fixed IP or DHCP Dynamic Host Configuration Protocol Depending on the selected mode further configuration items come as follows IP Mode Selection Description Local IP Fixed IP address Fixed IP Local Gateway Gateway IP address Local Subnet Subnet mask DHCP N A el NS Obtain DNS server address automatically Get DNS server address automatically when IP mode is DHCP Use the following DNS server addresses Enter the DNS server IP address manually Primary DNS server Secondary DNS server Ipv6 Ipv6 Address Enter the designated Ipv6 address Ipv6 Subnet Prefix Length Enter the bit number of Ipv6 Subnet Ipv6 Default Gateway Enter the designated lpv6 gateway e Ipv6 Link
18. C Alarm Signal Output Type NO NC Contact Signals Connection to External Device ALARM 2 NO TYPE 58 e 6 Appendix MCC201 MCC201H User manual Appendix B Serial Port RS 232 Port e Port Type 8 PIN Pin Arrangement Pin Description Pin No Pin Name Description 1 TX RS232 TX Transmit 2 RX RS232 RX Receive 3 GND Ground RS 422 485 Port Port Type 4PIN RS 422 485 TERMINALS Pin Diagram Pin Description Pin No Pin Name Description 1 RX RS422 RX 2 RX RS422 RX 3 TX RS422 TX or RS485 TRX It is selectable by S W Setup 4 TX RS422 TX or RS485 TRX It is selectable by S W Setup MCC201 MCC201H User manual 6 Appendix 59 TELESTE Legal declarations Copyright 2015 Teleste Corporation All rights reserved TELESTE is a registered trademark of Teleste Corporation Other product and service marks are property of their respective owners This document is protected by copyright laws Unauthorized distribution or reproduction of this document is strictly prohibited Teleste reserves the right to make changes to any of the products described in this document without notice and all specifications are subject to change without notice Current product specifications are stated in the latest versions of detailed product specifications To the maximum extent permitted by applicable law under no circumstances shall Te
19. Local Display Ipv6 Link Local MCC201 MCC201H User manual 4 Remote Configuration e 29 Port Base Port 1025 65535 Enter the Base Port number Network base port is use for communication with remote clients In order for camera and remote systems decoder or VMS NVR software to be connected the port number must be identically configured in camera side and client side HTTP Port 80 1025 65535 Enter HTTP port used for web based connection HTTPS Port 443 1025 65535 Enter HTTPS port used for secured HTTP connection RTSP Port 554 1025 65535 Enter RTSP port used for RTSP based connection The default RTSP port is 554 RTSP Real Time Streaming Protocol is a standard for media streaming between server and client Discovery UPNP By setting UPNP to ON it allows the discovery by the client according to UPNP Universal Plug and Play protocol Zeroconf By setting Zeroconf to ON it allows the discovery by the client according to Zeroconf protocol WS Discovery Discovery function based on web service is enabled It allows the discovery by Client SW which is supporting Onvif Authentication RTSP Authentication If RTSP Authentication set to ON user in the client side is asked to enter User ID and Password e HTTP API Authentication When HTTP API authentication set to ON HTTP Authentication is asked for all clients which use HTTP API 30 4 Remote Configuration MCC201 MCC201H User manual
20. User manual MCC201 MCC201H H 264 Encoder decoder This manual provides information on installation setup and operation of the video server as well as troubleshooting tips Video Networks MCC201 MCC201H User manual 59300507 rev002 Table of Content HAM eurer e O TO 1 About this Manual ii A A A A AAA EE eens 1 pce LE 1 leie Leen e 2 Part Nam s an FUNCIONS scende GAMA is a 3 SYSTEM CONMECHONS tte EE 5 a 8 3 System Opt EE 11 Remote Video Monta Ue Mesue 11 LIVE VIEW CONTO ee AA EE ee 12 Initialization ot IP addres Suaa NEEN ENEE rane ete dE E IRE ERE SERE ORE AER ARD 15 4 Remote Conflg ratiori eie t eoe eer eto ett aper AEN SP ERR ef EN EA ROUES yr ere teen 16 SYSTEM OR MEI UE EIB eise tete Moe ete e o th ttt e Mc ea ss tes 17 Audio Configuration jede aede di 26 NetWork GortflguratiOE zs ice eee oret te Perret te reed eee re Fe UT eh e Eae Feb edel ere dare aes 28 Serlali COMfGULATION err EE m 34 EVENT CON QUAN ace d AAA AAA sah Se de Rd ne E RAE i ded dS 37 PTZ Configuration A A RI IUE pero 42 Record Configura ON EE 43 5 Decoder Config 51 le lee CL BEE 51 Kette site UT EE 53 Event Configuratio e ECT 55 DISplay CONTGUIATION EE 56 e ee E TEE 57 Legal Declaration iaa EE 60 MCC201 MCC201H User manual e 1 Introduction About this manual This User Manual provides information on installation setup and operation of the MCC201 and MCC201H as well as troubleshooting tips Features MCC201 i
21. are adjusted not to drop any frames when the network bandwidths to some clients are limited In this case all clients can be affected by the averaged bitrate and frame rate Address Information Followed network information is displayed Read only IP Address The IP address for the video server either defined fixed address or address assigned by the DHCP Domain Name In case the video server is registered at DDNS server the registered domain name is displayed MAC Address Display the MAC address of the video server In case the video server is registered at DDNS server the MAC address is used in DDNS registration Connecting Client IP Addresses that are currently connected to system are listed MCC201 MCC201H User manual 4 Remote Configuration e 33 Serial Configuration Setup System Video Audio Network Serial Event Preset Record Serial COM1 RS 232 Port Protocol RS 232 v Bitrate 9600bps v Data Bit 8Bits v Parity None v Stop Bit 1Bits m COM RS 422 485 Port Protocol RS 485 Bitrate 2400bps Data Bit 8Bits v Parity None v Stop Bit 1Bits v PTZ PTZ Type Pelco D Mi PTZ ID 1 PTZ Port COM2 b Sensor Type Sensor 1 Oof 9N O ON C Sensor2 Oof OG N O ON C Sensor Schedule Select O Sensor On Sensor 1 0 11 2 3 415 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 VON HI TUE MIB WED MIB EE ETE LE EPEELT ECO TA BIEBEHBHENBI ERE MOE IE DAA ANNA Sensor
22. be identical 26 e A Remote Configuration MCC201 MCC201H User manual Mode e Select audio operation mode Mode Action Off No operation Tx Only Transmit only Rx Only Receive only Tx amp Rx Transmit and Receive Input Gain e Set audio input gain from 0 to 31 Audio Output Configure the audio source to be played on audio output port Decoded Audio Audio stream from client is played Loopback Audio data from audio input port is loop backed to the audio output port MCC201 MCC201H User manual 4 Remote Configuration 27 Network Configuration Setup Live View System Video Audio Network Serial Event Preset Record User Network Apply Local IP Mode Fixed IP Local IP 192 168 26 30 Local Gateway 192 168 10 1 Local Subnet 255 255 0 0 DNS Obtain DNS server address automatically Use the following DNS server addresses Primary DNS Server 0 0 0 0 Secondary DNS Server 0 0 0 0 IPv6 IPv6 Address IPv6 Subnet Prefix Length IPv6 Default Gateway IPv6 LinkLocal fe80 21c 63ff fea6 1111 64 e Port Base Port 2222 1025 65535 HTTP Port 80 80 1025 65535 HTTPS Port 443 443 1025 65535 RTSP Port 554 554 1025 65535 Discovery UPNP Q of O On Zerocont O Off O On WS Discovery O of O On Authentication RTSP Authentication Off O On HTTPAPI
23. ctable from 0 to 10 Information Display System ID and or server time can be display over the video window in Internet Explorer Each item can be turn on or off separately and position also can be configured This information is displayed after the video is decompressed 24 e A Remote Configuration MCC201 MCC201H User manual Burnin OSD Insert text for System ID and enable timestamp date amp time for the streamed video The information is added on top of video before encoding System ID and time respectively can be turned on or off in the video Position and Font size can be configured also System ID for Burnin OSD exists independently from normal System ID Note That size of Burnin OSD display varies according to the encoding resolution setting This is inevitable because Burnin OSD is inserted to the frames before encoding is performed The following table describes the rule for Burnin OSD display 1920x1080 2048x1536 2560x1600 2592x1936 Resolution Small 8x8 Middle 16x16 Large 32x32 352x480 352x240 352x576 352x288 2 1 0 720x480 720x240 720x576 720x288 2 2 1 640x480 800x600 1024 x 768 1280x720 1280 x 960 1280x1024 1440x900 1600x900 1680x1050 1920x1056 2 2 2 2 Both System ID and Time are displayed 1 Either System ID or Time can be displayed When both are enabled System ID is displayed 0 No items are displayed This is because video area is
24. der operation On the following pages are presented some major differences on the configuration settings compared to encoder operation Note When turning the operation from an encoder to a decoder requires a selection of the system mode and reboot of the device Once the Apply button is pressed a windows dialogue will appear to confirm the restart System Configuration Setup Live View System Video Audio Network Serial Event Preset Display User System General System ID Video Server Language English k Firmware Version Dec V1 103C 006 Board ID 93 Upgrade Firmware Upgrade Config Backup amp Restore Backup Config Backup Restore Config Restore Time Start Time 2011 06 23 16 41 36 Current Time 2011 06 23 16 50 51 Time Format YYYY MM DD hh mm ss E Time Zone GMT 12 00 International Date Line West vj O Automatically synchronize with NTP server NTP Server Name Reboot MCC201 MCC201H User manual 5 Decoder Configuration e 51 Video Configuration TELESTE Setup Live View System Video Audio Network Serial Event Preset Display User Video Apply Output Format Output Format PAL 720x576 e e I zu 1 Buffering 4 Output Format When MCC is used as a decoder only the basic video resolution formats are supported on the device outputs The list of formats is shown below TELESTE Setup Live View System Vide
25. e green LED on the Ethernet port will flash indicating the system is ready e Encoder LED Display PWR STATUS LINK DATA e e O O Red Green OFF OFF Blinking These LEDs show that the camera is connected but a decoder is not connected Once the encoder is connected to a decoder color of LINK LED will turn into green color and DATA LED will blink as video or audio transmissions occur Decoder LED Display PWR STATUS LINK DATA e e o O Red Green OFF Blinking These LEDs show that the Decoder has started without connecting to an encoder Once an encoder is connected the color of LINK LED will be turned to green and the DATA LED will blink as video or audio data transmissions occur MCC201 MCC201H User manual 2 Installation 9 Description of LEDs System status can be monitored with LED display LED State Description Off Power off PWR Red Power on Green blinking Normally operating Red System failure Needs diagnostics Constant change of colors between NTSC PAL setting does not match with input video Red and Green signal Red blinking Failed to obtain IP address in DHCP mode STATUS Constant change of colors between Green blinking 2 times Failed to register on DDNS server and Red blinking once Green blinking Red blinks Video loss in Encoder system once every 5 seconds Constant change of colors Formatting USB storage device Green Ora
26. e is UTC plus the current time zone offset for the considered location MCC201 MCC201H User manual 4 Remote Configuration e 19 Automatically synchronize with NTP server Synchronize the camera time with an NTP server using NTP network time protocol Name of the NTP server should be registered on NTP server Name The Network Time Protocol NTP is a protocol for synchronizing the clocks of computer systems over packet switched variable latency data networks It is designed particularly to resist the effects of variable latency by using a jitter buffer Reboot To reboot the video server operation Do not press the Reboot button unless the server needs a reboot Factory Reset Allsettings including user accounts and logs are cleared Factory Reset except network settings e Allthe settings except for current network settings are changed to default values 20 e 4 Remote Configuration MCC201 MCC201H User manual Video Configuration TELESTE System Video Video Encode Input Format Input deinterlace Resolution Framerate Preference Quality Bitrate Frame Interval H 264 Profile Dual Encode Use Dual Encode Dual Encode Algorithm Resolution Framerate Preference Quality Motion Detection Audio Setup Live View Network Serial Event PTZ Record User Composite PAL O op O On Oo 720x576 Scaling 25 CBR S lt lt lt Very fine
27. ecorded data by serious of events happening continuously can be merged to a single AVI file depending on pre post event time setting The size of file is limited to 10 200MB or 10 minutes In case of continuous recording AVI files are created in series and the size of each is limited to 10 200MB or 10 minutes e Search Actual recording a file currently being recorded doesn t appear until it is completed In case of Continuous recording a file will be shown after 10 minutes from the start of recording for a file is generated every 10 minutes 1 Press Search Page button on the Record setup page Dates with recording data will be shown as follows Search Page 2008 03 03 TIKILA 2 First choose the date for search and the list of AVI files will be shown 3 The file name shows the date and time Date Begin Time End Time avi Root gt gt 2008 03 03 O File Name Size 080303_165722_165731 avi 1 30 M 080303_165355_165608 avi 22 51 M EJ 080303_165143_165213 avi 4 48 M HIKOI 4 Press Root to move back to the page with date list 46 e 4 Remote Configuration MCC201 MCC201H User manual e Playback 1 Selecting an AVI file will show a dialog for opening or saving the file Do you want to open or save this file Name 080303 165143 165213 avi Type Video Clip 3 27MB AY open 11 save Gei While files from the Intemet can be useful some files can potentially 9 harm your computer If
28. ently it supports only video e Media Protocol Select protocol used for transmission of audio and video data between remote system and decoder The decoder system or VMS can choose media protocol among TCP UDP and Multicast e Remote Address Address of the remote system to connect Port Port of the remote system to connect e Remote Channel The channel can be selectable when the remote system has more than multiple video channels e Use Streaming Server Decoder system has the settings to connect to Encoder or IP Camera via the Streaming Server To connect to Encoder or IP Camera via Streaming Server Use Streaming Server of Remote group in Network page should be set to On and information of the Streaming Server SS needs to be configured appropriately SSIP address IP address of Streaming server SS port Enter Port number that is set when registering Streaming server SSID Enter Streaming Server ID SS password Enter Streaming Server Password Remote Remote Type Normal E Media Protocol TCP v Remote Address 192 168 10 243 Port 2222 Remote Channel Channel 1 ze Use Streaming Server 9 of O On SS IP Address 0 0 0 0 SS Port 2222 SS ID admin SS Password eee 54 e 5 Decoder Configuration MCC201 MCC201H User manual Event Configuration Setup Live View System Video Audio Network Serial Event Preset Display User Event Apply Local Sensor Bgeep Dalarmi C Alarm2 Sensor Beep lAlarm1 O Alarm2 Remote
29. es are supported Continuous Event Disconnect In case of Event recording event types can be selected among several events Selected event type is used for configuring the schedule table Up to 4 event types can be configured and each event type can be a combination of sensor video loss and motion event Pre event Time Specify the duration of recording before an event happens Post event Time Specify the duration after the event is cleared Schedule Table Actual recording mode is determined by Schedule Table where recording mode configured by day of a week and hour Each of recording mode configures the recording operation as follows Record off No recording Continuous Records continuously Disconnect Recording is started when the system loses the connection to its last client Decoder VMS NVR etc When there are multiple clients and one of the client is disconnected this doesn t happen Event Type Records when an event configured in Event Type setting happens Checking status of recording Recording status can be checked on the main view page Live View Setup Video Select Primary Secondary View Size O 5096 O 100 MCC201 MCC201H User manual 4 Remote Configuration e 45 Search and Playback Recorded video and audio data can be saved as AVI format in the disk In general one AVI file is created for an event in case of event based recording However it is possible that r
30. ess Save Label button 42 e A Remote Configuration MCC201 MCC201H User manual Record Configuration TELESTE Setup Live View System Video Audio Network Serial Event PTZ Record User Record Disk Information No disk Disk size Free space General Use Record off O Use Disk O Use FTP Event Type Event Type 1 _ sensor1 Sensor2 Motion video Loss Event Type 2 Sensor1 Sensor2 Motion L video Loss Event Type 3 _ sensor1 L Sensor2 C Motion L Video Loss Event Type 4 Sensort Sensor2 L Motion LI Video Loss Pre event Time Post event Time Schedule Table Record Of O Continuous Disconnect Select Event Type 1 O Event Type 2 Event Type 3 O Event Type 4 L o 1 2 3 4 5 o 8 9 to r1 12 13 14 15 16 17 18 t9 20 2 12223 TUE FRI MCC201 MCC201H User manual 4 Remote Configuration e 43 DISK SD memory can be used and at least 1GB size is recommended Either EXT3 or FAT32 file system can be used A disk with either EXT3 or FAT32 file system can be read in Linux PC However only disk with FAT32 file system can be read in Windows PC Less than 4Mbps of video bit rate is recommended when you record and monitor video simultaneously since frame dropping may happen due to performance limitation Disk information Be sure to restart the system after connecting an SD card During booting the system reads status of disk and initializes it Once the initializatio
31. is a standard format for transmission and storage of audio video and data 7 and is used in broadcast systems such as DVB and ATSC Transport Stream is specified in MPEG 2 Part 1 Systems formally known as ISO IEC standard 13818 1 or ITU T Rec H 222 0 Transport stream specifies a container format encapsulating packetized elementary streams with error correction and stream synchronization features for maintaining transmission integrity when the signal is degraded As MPEG TS itself supports only AAC as the audio algorithm only video is streamed when audio algorithm is set to G 711 MCC201 MCC201H User manual 4 Remote Configuration e 31 Related settings are as follows Destination IP Set the IP Address of the destination system which will receive MPEG TS stream Destination Port Set the Port of the destination system which will receive MPEG TS stream Mode MPEG TS Destination IP 192 168 10 14 Destination Port 1026 0 1026 65534 Even number only SNMP Setup for using SNMP Simple Network Management Protocol It is compatible to both SNMPv1 and SNMPvec Settings for using SNMP Simple Network Management Protocol are as following e SNMP Listen Port 0 161 1025 65535 The port is for connecting external devices when system operates as a SNMP client SNMP is not used by setting O value e SNMP Trap Destination IP Set the SNMP Trap Destination IP e SNMP Trap Destination Port 0 162 1025 655
32. lease note that configured settings should be saved first by pressing Apply button before using FTP Test function One of the following messages will come as a result of the test Message Description FTP connection tested The connection to the FTP server is successful successfully The connection to the FTP server failed It is necessary to check Failed to connect FTP server if the server is reachable and server address and port are correct The server is reachable but authentication failed Authentication failed SE ID and or password need to be checked File upload failed The user of the ID is not allowed for Failed t load fil A pret ete writing into the directory or FTP server can be full Failed to delete the test file The user of the ID doesn t have Failed t fil A the privilege for file deletion MCC201 MCC201H User manual 4 Remote Configuration e 41 PTZ TELESTE Setup Live View System Video Audio Network Serial Event PTZ Record User PTZ Zoom In Focus Near Focus Fa Menu On Preset Select Preset Number SelectPreset YV Event Holding Time sec 0 255 Apply Event Holding Time Edit Label Select Preset First Save Label Group Select Group Number Group 1 wl Modify Group Auto Parking Parking time 0 sec 0 3600 0 0f Parking action Preset e Select preset and insert the name of preset Setcamera position for the preset and pr
33. leste be responsible for any loss of data or income or any special incidental consequential or indirect damages howsoever caused The contents of this document are provided as is Except as required by applicable law no warranties of any kind either express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose are made in relation to the accuracy reliability or contents of this document Teleste reserves the right to revise this document or withdraw it at any time without notice CE 9 Teleste Corporation P O Box 323 FI 20101 Turku Street address Telestenkatu 1 20660 Littoinen FINLAND www teleste com
34. n of a disk is finished the status of disk is shown on Record page of web based setup System Video Audio Record Cisk informatio Setup Live View Network Serial Event Preset Record User Camera e nting and Recovering Bk Disk size 3 73 G ee space Unknow Refer to the chart for checking the status of disk Disk status Disk error detected No disk Searching Disk information Mounting and Recovering Disk Disk format needed Unknown disk type detected USB Disk available Disk removed or in abnormal state Disk is not connected to the system Checking the status of disk Refresh the page and wait until the status is changed Performing recovery process when disk damage is found It takes from seconds to minutes for recovering Disk is attached but the type of the file system is unknown or damaged Available to be used for recording Disk is detached during operation or there is damage on the file system If it happens while disk is connected it is recommended to format the disk 44 4 Remote Configuration MCC201 MCC201H User manual General e Use record Off Recording function will not be used when Off is selected Use Disk Recording will be enabled and data will be written to a disk Use FTP Recording will be enabled and data will be uploaded to an FTP server In this mode FTP upload by event is automatically disabled Event Type Three recording mod
35. nge Red color in turn Off No connection to remote system Green Connected to a remote system LINK Red blinking Decoder only trying to connect to an Encoder Illegal connection Orange i cii unsupported combination of system modes Green Data transmission in progress DATA Red Data loss Off No data transmission 10 e 2 Installation MCC201 MCC201H User manual 3 System Operation Remote Video Monitoring There are two ways to monitor video when the center system and MCC201 are connected In order for a proper operation an IP address must be set accordingly Default IP Address http 192 168 10 100 Default ID admin Default Password 1234 Video Monitoring with Decoder System Once the encoder IP address is set in the remote IP address section of the decoder the decoder system will connect to the encoder system and start receiving the video images Normally a monitor connected to the decoder will display video images MCC201 MCC201H User manual 3 System Operation e 11 Video Monitoring using Internet Explorer When the MMC201 or MCC201H is managed by a Windows Explorer browser shortly after logging the OS will ask permission to install an Active X component publisher is Teleste Corporation to the user s computer This plug in component is needed in order to activate the Live View software video decoder as shown below Should you not accept the activation the video is not available within the browser However
36. nual 4 Remote Configuration e 35 Sensor Schedule m Choose Sensor OFF or Sensor ON and click the below schedule cells to make Sensor Schedule according to day of week and hour Click desired Cell to set schedule 92 516 7 8 9 110111112113 114115 116 17118 19 20 21 22 23 SUN MON TUE WED THU FRI SAT Click desired Time Line or Date Line to set schedule 0 1 2 3 4 5 6 7 8 9 ale 223 SUN Bi MON E TUE i WED D U H HHHHHHHHHHHHHHHHHHHH FRI SAT E To set cells in the schedule click below Empty Cell 36 e A Remote Configuration MCC201 MCC201H User manual Event Configuration System Event Local Sensor1 Sensor2 On Video Loss On Motion Remote Sensor Sensor2 Sensor3 Sensor4 On Disconnect On Disconnect Duration Beep Alarm1 Alarm2 E mail Notification Server Address Port Sender Address Authentication on SMTP server ID Password SSL Destination Address Video Clip Attaching Number of Frame FTP Upload Server Address Port ID Password FTP Filename FTP Base Directory Upload Video Number of Frame Continuous Upload Upload Duration Upload Interval Video Audio Setup Network Serial Event C E mail C E mail C E mail C E mail DAlarm2 DAlarm2 DAlarm2 DAlarm2 OBeep DAlarm1 OBeep DAlarm1 OBeep DAlarmi L1Beep DAlarm1 C E mail C E mail C E mail C E mail DAlarm2 DAlarm2 DAlarm2 DAlarm2 L1Beep DAlarmt L1Beep DAlarm1 OBeep
37. o Audio Network Serial Event PTZ Display User Video Apply Output Format NTSC 720x480 Output Format SREL TE 720p60 1280x720 Buffering 1080i60 1920x1080 P 720p50 1280x720 1080i50 1920x1080 1080i59 94 1920x1080 720p59 94 1280x720 1080p30 1920x1080 e Buffering You can store maximum 30 decoded frames temporarily by using buffering before displaying the frames Displaying stored frames is smoother than displaying in real time However displaying stored frames causes delay because of process of buffering 52 e 5 Decoder Configuration MCC201 MCC201H User manual Network Configuration Network configuration page has a section for specifying the remote system to be connected to MCC encoder or IP camera System Video Audio Network Network Local IP Mode Local IP Local Gateway Local Subnet DNS Setup Serial Fixed IP bd 192 168 26 33 192 168 10 1 255 255 0 0 Event Live View Preset Display User Apply Obtain DNS server address automatically Use the following DNS server addresses Primary DNS Server Secondary DNS Server Port Base Port HTTP Port HTTPS Port RTSP Port Discovery UPNP Zeroconf WS Discovery Authentication RTSP Authentication HTTPAPI Authentication RTP Session Use RTP Session Destination IP Destination Port User Name File Name SNMP SNMP Listen port SNMP Trap Destination IP SNMP Trap Destinati
38. om built in the camera PTZ Control Control PTZ and PTZ Control Panel is used for controlling external PTZ devices when the external PTZ devices are connected through serial port It is possible to make zooming control by Zoom in out buttons of PTZ control Panel In order to use digital zoom select Digital zoom ON in the Camera tab Stop Stop on going PTZ action A Focus Near Focus Far Auto Focus Adjust the focus of the lens Select Preset Set preset position and move to the specific preset position Goto Move to the selected preset entry if the preset entry is set Set Set the current position to the selected preset entry Clear Delete the selected preset entry Sensor Input Display the status of the sensor in real time This camera supports one sensor input When the sensor of the camera is working the sensor light turns red MCC201 MCC201H User manual 3 System Operation e 13 e Alarm Output Operate the alarm device by pressing the number icon This camera supports one alarm output A number icon indicates status of the alarm device e Snapshot Capture video images and store them as BMP or JPEG files e Talk Transfer audio from PC s mic to the camera e File Record Recording to an AVI file on Live View page is available AVI files are generated in the specified folder or in specified file name on the PC where web browser is running 1 Press Set button to select folder or create a
39. on Port Remote Type Media Protocol Remote Address Port Remote Channel Use Streaming Server SS IP Address SS Port SS ID SS Password DDNS Server Address Information Current IP Current Domain 0 0 0 0 0 0 0 0 i222 Kf 80 k 554 K O of O On O of O On O of O On O of O On O of O On O of O On 0 0 0 0 EE 1025 65535 80 1025 65535 443 443 1025 65535 554 1025 65535 0 1026 65534 Even number only ch0 sdp 0 0 0 0 Normal TCP E v 161 0 161 1025 65535 0 162 102565535 192 168 26 102 2222 Channel 1 O of O On EI 0 0 0 0 2222 O None O TrueDNS O DynDNS O Vdyn O Check IP Disable 192 168 26 33 Not RegisteredB MAC Address 00 1C 63 A6 04 2E 1 192 168 10 71 0 0 Connecting gt 495 168 26 102 1 0 MCC201 MCC201H User manual 5 Decoder Configuration 53 e Remote Type Normal Connection for Encoder and decoder RTSP RTP Decoder system can make connection though RTSP protocol and get the stream via RTP It is also possible to make connection with other vendor s H 264 IP camera supporting standard RTSP RTP and standard H 264 algorithm To make RTSP connection set Hemote Type to RTSP enter the RTSP URL of remote system to Remote Address and RTSP access port number to Remote Port Curr
40. onfigure the actions when the link connection with peer system is disconnected Multiple actions can be set for a single event e Alarm and Beep activation duration Set the duration of alarm or beep activation in case of an event If it is set to continuous it will be in active state until an operator reset it manually Display Configuration Setup Live View System Video Audio Network Serial Event Preset Display User Display App Disconnect O Freeze O Black Screen LED Video v Disconnection Decoder system s output mode on disconnected state can be configured Freeze Video image of the last frame is shown when there is disconnection Black Screen Black Screen is shown when there is disconnection e LED Select from Video Audio and Serial to be indicated by Data LED When there is the selected data Video or Audio or Serial communication between the encoder and the decoder Data LED will indicate the status 56 e 5 Decoder Configuration MCC201 MCC201H User manual 6 Appendix Appendix A Sensor and Alarm Port Sensor Port Terminal Type Voltage Rating 150VAC Current Rating 2A Color Red Sensor Signal Input Type NO Contact Signals Connection to External Device ho MCC201 MCC201H User manual 6 Appendix 57 Alarm Port Terminal Type Voltage Rating 150VAC Current Rating 2A Relay Type Contact Rating 1A 30VDC Switching Power Max 30W 62 5VA Switching Voltage Max 60VD
41. re case sensitive YYYY year MM month DD day hh hour mm minute Ss second EVENT event type Sensor1 Motion ADDR address of the server Domain name when DDNS is used Otherwise IPaddress avi or jpg will be added automatically at the end of the filename depending on the type of video file FTP Base Directory Specify the name of the directory to be created in the FTP server It is valid only when Use Record is set to Use FTP on Record session Upload video Primary Video and Secondary Video H 264 only JPEG Capture can be selected for uploading The duration of video clip can be configured with Pre Event Time and Post Event Time in Event Record section Number of Frame Enter frame number of JPEG Capture from 1 to 10 40 e 4 Remote Configuration MCC201 MCC201H User manual e Continuous Upload Continuous upload On allows video clips to be transmitted regularly regardless of occurrence of events When this mode is turned on FTP upload by events is suppressed e Upload Duration Specify recording duration of a video clip to be transmitted Max 300 sec e Upload Interval Specify transmission interval Max 3600 sec Upload Duration is not included in Upload interval For example if Upload Interval is 60 seconds and Upload Duration is 20 seconds a video clip for 20 seconds is transmitted every 80 seconds e FTP Test FTP upload function can be tested with this button P
42. rver Authentication failed Connection to the SMTP server failed It is necessary to check if the server is reachable and server address and port are correct The server is reachable but authentication failed ID and or password need to be checked SMTP server rejected the mail The server is reachable but mail sending failed due to a reason other than authentication This error happens often when the server authenticates according to its own rule For example IP addresses of a specific range or addressed of a specific suffix are allowed MCC201 MCC201H User manual 4 Remote Configuration e 39 FTP Upload Specify the information to upload event information when FTP is selected as an event action Server Address Enter an address of an FTP server to receive video files Port Specify a port for FTP operation Port 21 is the default port in FTP operation If a different port is configured in the FTP server this port needs to be changed accordingly ID amp password Enter ID and Password for accessing the FTP server e FTP File name The names of files upload by FTP can be specified by user If a fixed name is specified the file is overwritten repeatedly Max length of a file name is 60 characters If the name is left blank file name is determined according to the internal rule implemented in the firmware The following macros are supported to form variable parts of file names The strings a
43. s a video and audio transmission system that provides broadcast quality audio and video based on IP networking MCC201 can operate either as an Encoder or as a Decoder the desired mode is user selectable MCC201H is a model variant which has all other functions available except HD SDI operation Video Highly efficient compression algorithm H 264 Baseline and High profiles amp MJPEG support Wide range of transmission rates Primary stream 32 kbps 10 Mbps secondary stream max 1 Mbps Various transmission modes CBR VBR Motion detection Support for analogue baseband video HDMI video and HD SDI video Note HD SDI video not available on MCC201H Audio Multi Transmission Mode Unidirectional Mode IP server to Client PC or Decoder Client PC or Decoder to IP server Bi directional Mode Network Fixed IP amp Dynamic IP DHCP support 1 1 1 N support e Multicasting e Automatic transmit rate control according to network conditions e OnVIF PSIA compliant Serial Data e RS 232 support e RS 422 4 w or RS 485 2 w support e Data pass through mode Serial data communication between Encoder Decoder MCC201 MCC201H User manual 1 Introduction e 1 Sensor and Alarm e Support direct connections of external sensor and alarm devices e Event Alarm c SB Connection to internal or external USB storage for remote access recording and playback User Interface System configuration by
44. sible actions for events Action Description Beep Triggers beep port Alarm out Triggers alarm relay port E mail Sends E mail to the specified address AVI file can be attached FTP Upload AVI file to a specified FTP server Preset Move to the Preset position Local amp Remote Event Configuration Sensor1 Sensor2 Configure the actions when the sensor is activated Multiple actions can be set for a single event On Video Loss Configure the actions when video input signal is lost Multiple actions can be set for a single event On Motion Configure the actions when motion is detected Multiple actions can be set for a single event On Disconnect Configure the actions when the link connection with peer system is disconnected Multiple actions can be set for a single event This event happens when the last client which has been receiving video from the camera loses the connection Alarm and Beep activation duration Set the duration of alarm or beep activation in case of an event If it is set to continuous it will be in active state until the operator resets it manually 38 4 Remote Configuration MCC201 MCC201H User manual E mail Notification Specify the information to send event information when E mail is selected as an event action Server Address Enter an address of mail SMTP server Port Specify a port for SMTP operation Port 25 is the default port in SMTP
45. tored from many remote center locations Maximum connections would be limited by the network bandwidth Functionally the VMS Video Management System software can replace the decoder Multicast Mode In the network supporting multicast mode if Multicast is setup as a system protocol you can use bandwidth efficiently regardless of the number of decoders In 1 N connection a large number of decoders can receive audio and video data from an encoder by using a single streaming transmission e Relaying Site IP server Remote Center 1 Remote Center 2 Ee Decoder E gt Decoder In this arrangement video and audio can be retransmitted from a center to another center The arrangement is useful when the network bandwidth at the site is limited while there is more than one center wanting to monitor the site 6 e 1 Introduction MCC201 MCC201H User manual e VMS Video Management System Site Remote Center CA E Site Remote Center Cia VMS Video Management System is a Windows based remote monitoring program to access multiple encoders for real time monitoring or control of the encoders and connected cameras A typical integration to VMS system is done via OnVIF interface MCC201 MCC201H User manual 1 Introduction 7 2 Installation Connecting Video e Connecting with Megapixel Camera Connect a camera which supports HDMI or HD SDI output to the HDMI or HD SDI
46. tween 32 10240 kbps Bitrate mode CBR encoding allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth In order to maintain the bitrate limit the video is dynamically controlled regardless the complexity or content changes on the incoming video eo Frame Interval The I frame interval can be selected between values 1 to 255 For example a value of 1 is meaning that every sent frame is l frame whereas a value of 25 is meaning that every 25th frame is an l frame e H 264 Profile Select H 264 Profile High Profile or Baseline Profile The standard defines various sets of capabilities which are referred to as profiles targeting specific classes of applications High Profile HiP The primary profile for broadcast and disc storage applications particularly for high definition television applications for example this is the profile adopted by the Blu ray Disc storage format and the DVB HDTV broadcast service Baseline Profile BP Primarily for low cost applications that require additional data loss robustness this profile is used in some videoconferencing and mobile applications This profile includes all features that are supported in the Constrained Baseline Profile plus three additional features that can be used for loss robustness or for other purposes such as low delay multi point video stream compositing Dual Encode Use Dual Encode Select ON to enable the dual encoding with
47. urrent Time 20 10 2015 11 20 44 Time Format DD MM YYYY hh mm ss v Time Zone GMT 02 00 Helsinki kyiv Riga Sofia Tallinn Vilnius Y Automatically adjust clock for Daylight Saving Time O Automatically synchronize with NTP server NTP Server Name pool ntp org Reboot Reboot Factory Reset MCC201 MCC201H User manual 4 Remote Configuration e 17 General System ID Enter System ID that is used as a camera title The set System ID is displayed with video image on Web browser The System ID is also transferred to remote software such as VMS and displayed on it e Burnin OSD System ID The text string added in here shall be inserted on top of video before encoding and it is permanently included with video stream Only alphanumeric and blank characters are allowed Position and size can be configured on Burnin OSD section of Video page Language Select the language to be used for web based configuration Firmware e Firmware version Displays the current firmware version e Board ID Displays the network board ID of the video server Upgrade For the firmware upgrade Press Browse button to select a firmware file from the computer or network drive Press Firmware Upgrade button to start to upgrade Messages for showing status downloading upgrading will be displayed Z Di The video server will reboot automatically after completing upgrade Note Do not switch the power off during
48. w screen appears as below Press Setup button located in the upper right area of the monitoring screen to go to the server setup For Remote Setting user should be authorized higher than manager level Enter IP address Press Setup button A 88 0 e Server x Live View Setup Video Select Primary Secondary View Size O 50 100 Digital Zoom r 4 The remote configuration window may be slightly different depends on the system modes Encoder Decoder The general explanation of the configuration in this manual is based on Encoder system and differences according to the modes will be clarified when needed The configurations are grouped into 10 categories System Video Audio Network Serial Event PTZ Record User and Camera Any configuration changes are not applied until Apply button is pressed Leaving the page without pressing Apply button any changes in the page will be discarded 16 4 Remote Configuration MCC201 MCC201H User manual System Configuration TELESTE Setup Live View System Video Audio Network Serial Event PTZ Record User System General System Mode System ID MCC201 Burnin OSD System ID alphanumeric characters only Language English v Side Pane Position 8 Let O Right Firmware Version V1 507B02 T720 Model 2000 222 Upgrade Browse Firmware Upgrade Config Backup Restore Backup Config Backup Restore Browse Time Start Time 20 10 2015 11 14 51 C
49. web browser Internet Explorer recommended High Reliability Reliable embedded system System recovery by watchdog functions Product and Accessories USER GUIDE MCC201 MCC201H User Manual Power adapter and Cable in CD 2 e 1 Introduction MCC201 MCC201H User manual Part Names and Functions Front View B 7 AUS PWR STATUS SENSOR ALARM 00 ET 00 NM LINK DATA AUDIO HDMI OUT HDMI IN ETHERNET MCC201 Position Description Function 1 Reset button Initialization of network setting 2 LEDs Display power On Off condition Link Status and data 3 USB USB 2 0 port for any USB device 4 Audio In Out Audio Input and Output 5 Sensor Sensor Input 6 Alarm Alarm or Relay Output 7 HDMI In Out HDMI Video Input and Output 8 LAN Ethernet 10 100Base TX electrical Ethernet interface MCC201 MCC201H User manual 1 Introduction Rear View ot T X RS 422 485 TIR X X RS 232 um 0000 COMPOSITE HD SD SDI Position Description Function 1 POWER In DC 12V power input 2 RS 422 485 Serial port for PTZ control and etc 3 RS 232 Serial port for PTZ control and etc 4 Composite Out Composite Video Output 5 Composite In Composite Video Input 6 HD SD SDI Out HD SD SDI Video Output MCC201H not in use 7 HD SD SDI In HD SD SDI Video Input MCC201H not in use 4 1 Introduction MCC201 MCC2
50. you do not trust the source do not open or save this file What s the risk 2 Pressing Save button the file will be stored in the PC The AVI file can be played with Windows Media Player 3 If you press Open in the dialog the file will be downloaded and played automatically with Media Player 4 Another connection through web is disabled during downloading and it is also not allowed to download two AVI files at the same time MCC201 MCC201H User manual 4 Remote Configuration e 47 e Deletion of data 1 f you want to delete recorded files select the files by checking the item in front of each file and press Press Delete button Delete button Root gt gt 2008 03 03 Delete O File Name Size O 080303_165722_165731 avi 1 30 M O 080303 165355 165608 avi 22 51 M E 080303_165143_165213 avi 4 48 M i i gt Lot 2 ltis possible to delete multiple files at once 48 e 4 Remote Configuration MCC201 MCC201H User manual User Configuration Setup Live View System Video Audio Network Serial Event Preset Record User User User List ID Privilege Level admin Admin Modify Password Modify Privilege Login Policy Skip Login O Disable O Enable Privilege Level After Login Skipped Apply User List e User can be registered and privilege level of a user can be specified User configuration is allowed only to admin user Max 16 users can be registered and each user can have one of four privileges
Download Pdf Manuals
Related Search