Decoded MSR Series
Contents
1. ON ON 3 Keyboard USB Type Carriage Return Selection CR Enable CR Disable SW 7 OFF ON 4 Sending SS ES Selection for KB USB and RS 232 Send Non Send SW 8 OFF ON C Right SW Block 1 KB USB and RS 232 Wedge Device Selection KB RS 232 SW 1 OFF ON 2 RS 232 Baud Rate Selection 1200 2400 4800 SW 2 OFF ON OFF SW 3 OFF OFF ON Special Output Data Format Single Track STX Data Checksum of Data x Dual Track STX Track 1 or Track 3 Data Checksum of Data STX Track 2 Data Checksum of Data Triple Track STX Track 1 Data Checksum of Data STX Track 2 Data Checksum of Data STX Track 3 Data Checksum of Data Note x STX Start Text ETX End Text 02 hex 03 hex DLE Data Link Escape 10 hex Data lt SS gt lt Card Data gt lt ES gt Please check lt SS gt and lt ES gt in Normal Output Data Format section2. 5 0 0 8 010 0 2 8 0 0 0 0 0 00 1 0 1 1 1 0 0 Dimensions 158mm L x 43mm W x 44mm H Weight 170g Cable length 1 5 meters Interface keyboard RS 232 or USB 4 LED INDICATORS 1 Green LED Power on indicator 2 Red LED Good read indicator After altering the switch set B Left SW Block 1 Track Data Out ut Selection ing you should turn on the power again SW 5 OFF 4 RS 232 Send CR LF Send CR Send CR LF SW 6 ON OFF 5 Track 2 Account number Only If selected the reader will send out the message before the first separator Character and discard the following message Enable Disable SW 7 ON OFF Track Track Any 1 Track 2 Track Track 1 amp 2 2 amp 3 SW 1 OFF ON OFF OFF ON SW 2 OFF OFF ON OFF OFF SW 3 OFF OFF OFF ON ON 6 Inter character Delay for MSR KB Series and Special Output Data Format for MSR RS 232 Series a For MSR KB USB Series 10 ms 2 Language and JIS 2 amp ALT Mode setting SW 8 ON U S Germany Spanish France Italy Swedish _JIS 2 SW 4 OFF ON OFF OFF ON OFF b For MSR RS 232 Series Special SW 5 OFF OFF ON OFF OFF ON SW 8 ON SW 6 OFF OFF OFF ON
3. Note 9V DC power input model should request to supplier e RS 232 connector D Sub 9 pin Female Pin 2 Wire Red Function TX 7 NORMAL OUTPUT DATA FORMAT 1 Single Track SS Card Data 2 Dual Track SS Track 1 or 3 Data SS Track 2 Data Triple Track SS Track 1 Data SS Track 2 Data SS Track 3 Data Notes 1 SS Start Sentinel for Track 1 for Track 2 or 3 2 ES End Sentinel for Track 1 2 or 3 3 lt Carriage Return Carriage Return can be set by Left SW 7 4 Selectable setting for SS ES and lt MAGNETIC STRIPE CARD READER oded MSR Series _ Contents 1 Introduction 2 Features 3 Specifications 4 LED Indicators 5 Switch Settings 6 Installation Steps 7 Normal Output Data Format MSR Color M beige B black Interface K Keyboard R RS 232 U USB Track 01 track 1 02 track 2 03 track 3 12 track 1 amp 2 23 track 2 amp 3 33 track 1 amp 2 amp 3 40 JIS 2 1 INTRODUCTION Welcome to use the Magnetic Stripe Card Reader The card reader is designed with keyboard emulator output or RS 232 serial interface This user s manual provides detailed information about the card reader include key features installation procedure specifications dip switch settings and output data format etc 2 FEATURES e Read data encoded on magnetic stripe cards that meet ISO sta
4. 6 INSTALLATION STEPS l For Keyboard Wedge Reader Step 1 Turn the computer system power off and unplug the keyboard cable Step2 Connect the keyboard cable into the short cable of the Reader Step3 Connect the long cable of the Reader into the keyboard input socket on the computer system Step4 Turn the computer system power on then you can hear a beep sound for confirming the reader s self test and Green LED will be lit to indicate that the Reader is ready for reading 2 For USB Reader Step 1 To make sure the Windows USB utility is available in your computer Step 2 Connect the MSR s USB cable to the USB port on the computer the Green LED will be lit to indicate the MSR is ready for operation For RS 232 Serial Reader Step 1 Turn the computer system power off Step 2 Connect the Reader s cable to the RS 232 port on the computer system Step3 Connect the DC power adapter to the power jack on the cable end of the Reader then plug the adapter into AC socket You can hear a beep sound for confirming the Reader s self test and Green LED will be lit to indicate that the Reader is ready for reading Step 4 Turn the system power on and run your application software include one driver utility to get the data from the serial port which connects with the Reader IAC power source Ldltdddddddddddddae e 5V DC power jack on the RS 232 cable end To be connected with 5V DC power cno adapter Inner pin is positive
5. ndards Bi directional card swipe and read capability Software and hardware modification is not required Single dual and triple tracks decoding available Switch selectable carriage return sending start end byte and track 2 account number Keyboard types and languages are selectable by DIP Switchs in Keyboard Wedge Reader RS 232 parameters are also selectable in Serial Reader Power is supplied by the computer to operate the Keyboard Wedge Reader one power retrieve cable is bundled to the Serial Reader Power up diagnostics Good read confirmation by beep sounds Full one year limited warranty Magnetic Head Life 300 000 passes minimum 1 000 000 passes version is available upon request 3 SPECIFICATIONS e Decording Method Two frequency coherent phase F2F compatible with ISO standard Swipe Speed 5 to 60 inch sec Power consumption 80 mA max at 5V DC Operating Temperature 0 50 C Humidity 10 90 relative Magnetic Head Life 300 000 passes minimum 5 SWITCH SETTINGS oO 2 3 RS 232 Data bit and Parity Selection Data bit 7 Parity Odd Data bit 7 Parity Even Data bit 8 Parity Even Data bit 8 Parity None SW 4 OFF ON OFF ON OFF ON ON Left SW Block A Default Settings Right SW Block ON 1 OFF 0 Switch Right SW Block Models 1 314 5 6 7 MSR KB USB 0 MSR RS 232 0 SW
Download Pdf Manuals
Related Search