MEGA GO PAR64 RGBA
Contents
1. buttons to adjust the sound sensitivity R G B A Press either one of these buttons and the press the or to adjust the brightness Press the Flash Button to activate strobing and use the or to adjust the Flash rate and Use these buttons to adjust the flash rate speed of the Auto Run mode sound sensitivity and the intensity output of the RGB colors These buttons are also used to scroll through the different static colors auto run programs and sound active programs ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 15 MEGA GO PAR64 RGBA 1 Channel Mode COLOR MACROS Please see the color macro chart page 20 COLOR MACROS Please see the color macro chart page 20 DIMMER 0 100 RED 0 100 GREEN 0 100 BLUE 0 100 AMBER 0 100 MEGA GO PAR64 RGBA 5 Channel Mode 0 100 r 0 100 BLUE 0 100 AMBER 0 100 MASTER DIMMER 0 100 ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 16 MEGA GO PAR64 RGBA 6 Channel Mode MEGA GO PAR64 RGBA 8 Channel Mode 0 255 0 100 0 100 0 255 0 100 0 100 0 255 0 100 0 100 DT ll sen AMBER 4 AMBER 0 255 0 100 Rare 0 100 Ep MASTER DIMMER 5 COLOR MACROS 0 255 0 100 0 255 Please see the color macro chart page 20 0 255 COLOR MACROS STROBING PROGRAM SPEED SOUND A Please see the color macro chart page 202. Power Cord Daisy Chain 30 Fixtures Max Fuse 2 Amp Weight 5lbs 2 2Kgs Dimensions 10 5 L x 10 25 W x 4 5 H 262 x 260 x 110mm Colors RGB Color Mixing DMX Channels 7 DMX Modes 1 Channel Mode 2 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode 7 Channel Mode amp 8 Channel Mode Warranty 2 Year 730 days Limited Warranty This depends on charging frequency See Warranty page for details Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 823 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 te 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On facebook com americandj twitter com americandj youtube com adjlighting
3. Rev 4 14 User Instructions MEGA GO PAR64 RGBA Introduction Unpacking Thank you for purchasing the MEGA GO PAR64 RGBA by ADJ Products LLC Every MEGA GO PAR64 RGBA has been thoroughly tested and has been shipped in perfect operating condi tion Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged care fully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free cus tomer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The MEGA GO PAR64 RGBA is a rechargeable lithium battery powered DMX intelligent LED par fixture This unit give you the freedom to set up your fixture where ever you wish without the restric tions of power The built in battery will keep charge for up to 8 hours full on from a full single charge This fixture can be used in a stand alone mode or connected in a Master Slave configuration This wash has five operating modes Sound Active mode Auto Run mode RGB mode Static Color mode and DMX control mode Customer Support ADJ Products LLC provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us
4. 251 255 165 35 1 0 0 0 Channels 1 2 3 amp 4 will not work when Channel 5 is being used MEGA GO PAR64 RGBA Photometric Chart When using Channels 1 5 Channel 6 will control strobing oR D30 426 143 57 4 32 4 a 4 When using Channel 7 values 8 135 Channel 6 will control the speed of the programs Channel G D30 1089 366 148 78 4 5 will control the Fade time of the programs 8 D30 872 303 125 64 8 an lux _A D30 294 74 1 30 2 16 6 92 J When using Channel 7 values 136 255 Channel 6 will control the sound sensitivity Sound sen Leesa D30 at oe 2 l se ne En sitivity control will start working after Channel 6 is past the DMX value of 31 es N y SS BS Beat aS a ee gt a Raa eel 1 13m rs as ee 2 25m 0 1 0 2 0 3 0 4 0 5 0 Distance m ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 19 ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 20 MEGA GO PAR64 RGBA Battery Status amp Charging Battery Status This function is used to check the life status of the battery Plug the fixture in and press the MODE button until bXXX is displayed XXX represents an number between 000 and 100 The number that is displayed is the remaining battery life If b is displayed it means the battery is dead or you are running the unit on AC power Please do not let the battery fully die this severly shortens the l
5. SENSITIVITY Channels 1 2 3 amp 4 will not work when Channel 6 is being NOTHING used STROBING SLOW FAST PROGRAM SPEED SLOW FAST MEGA GO PAR64 RGBA 7 Channel Mode SOUND SENSITIVITY OFF RED PROGRAMS SOUND ACTIVITY 0 100 OFF 2 GREEN PROGRAM 1 0 100 PROGRAM 2 BLUE PROGRAM 3 0 100 PROGRAM 4 AMBER PROGRAM 5 0 100 PROGRAM 6 e COLOR MACROS PROGRAM 7 0 255 Please see the color macro chart page 20 PROGRAM 8 STROBING PROGRAM 9 NOTHING PROGRAM 10 16 255 STROBING SLOW FAST PROGRAM 11 MASTER DIMMER PROGRAM 12 0 100 PROGRAM 13 Channels 1 2 3 amp 4 will not work when Channel 5 is being PROGRAM 14 used 120 127 PROGRAM 15 ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 17 ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 18 MEGA GO PAR64 RGBA 8 Channel Mode MEGA GO PAR64 RGBA Color Macro Chart Kakau Value Function Color DMX RGBA COLOR INTENSITY Color DMX RGBA COLOR INTENSITY No VAULE RED GREEN BLUE AMBER No VAULE RED GREEN BLUE AMBER PROGRAMS SOUND ACTIVITY Color 0 20 0 0 0 0 Color25 136 140 254 5 97 128 135 PROGRAM 16 ot 0 Color2 21 25 255 0 0 0 Color26 141 145 175 77 13 lo 136 143 SOUND MODE 1 T 26 30 0 255 0 0 cae 146 150 119 130 199 Jo 144 151 SOUND MODE 2 Colors 31 35 0 lo 25
6. The MEGA GO PAR64 RGBA has 7 DMX channel modes please see page 12 13 for the different modes The DMX address is set on the back panel of the MEGA GO PAR64 RGBA Your unit and your DMX con troller require a standard 3 pin XLR connector for data input and data output Figure 1 We recom mend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on S either end of the cable Also remember that DMX Figure 1 cable must be daisy chained and cannot be split ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 8 MEGA GO PAR64 RGBA Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 i XLR Male Socket XLR Female Socket 1 1 1 Ground 2 Cold 1 1 1 i I L Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con ne
7. The battery pack is constructed in a way that no short circuit will occur which may cause smoke or fire 3 3 Do No Disassemble the Batteries 1 Never disassemble the batteries Doing this may cause a internal short circuit in the battery which may lead to harmful fumes fire explosion or other prob lems 2 Electrolyte Gel is harmful Electrolyte Gel should not leak from the LIR battery Should the electrolyte gel come into contact with the skin or eyes flush the ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 5 MEGA GO PAR64 RGBA Battery Precautions area of contact immediately with fresh water and seek medical attention immediately 3 4 Do Not Expose the Battery to Heat or Fire Never incinerate or dispose of the batteries in fire This may cause an explosion which would be very dangerous 3 5 Do Not Expose the Battery to water or liquids Never soak drop the batteries in liquids such as water seawa ter drinks such as soft drinks juices coffee or other 3 6 Battery Replacement For battery replacement please contact ADJ customer support 800 322 6337 3 7 Do Not use a damaged Battery The battery could be damaged during shipping caused by shock Should the battery be found damaged including dam ages to the plastic casing of the battery deformation of the battery package smelling of an electrolyte or leakage of the electrolyte gel or other DO NOT use the battery A battery with a odor o
8. outside of the return pack age A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the ship ping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by con tacting our customer support team on our customer support number All packages returned to the service department not displaying a R A number on the outside of the package will be returned to the shipper MEGA GO PAR64 RGBA The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp CUELA ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 3 MEGA GO PAR64 RGBA Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the
9. s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published This warranty was revised after December 1 2012 MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 23 MEGA GO PAR64 RGBA Specifications Model MEGA GO PAR64 RGBA Voltage 100V 240V 50 60Hz Battery Life 8 Hours Full On Full Charge Battery Lifetime Average Lifetime is 500 Charges LEDs 177 x 10mm LED s 36 Red 54 Green 53 Blue amp 34 Amber Beam Angle 30 Degrees Working Position Any safe working position Power Draw 22W
10. 5 o Color 151 155 147 164 22 0 152 159 SOUND MODE 3 Colors 36 40 0 0 0 255 Color29 156 160 88 2 163 lo 160 167 SOUND MODE 4 Color6 41 45 255 255 0 0 Color30 161 165 0 38 86 0 Color7 46 50 255 0 255 o Color31 166 170 0 42 208 o 168 175 SOUND MODE 5 Colors 51 55 255 0 0 255 Color32 171 175 _ 52 48 209 o Color9 56 60 0 255 255 o Color33 176 180 1 34 201 0 176 183 SOUND MODE 6 Colorl0 61 65 0 255 0 255 Color34 181 185 0 45 212 0 Colorl1 66 70 0 0 255 255 Color35 186 190 0 21 192 Jo 184 191 SOUND MODE 7 192 199 SOUND MODE 8 cir ns a es fas_fo eas ni fo so olor i olor 200 207 SOUND MODE 9 Colorl4 81 85 0 255 255 255 Color38 201 205 0 97 166 0 208 215 SOUND MODE 10 Colorl5 86 90 255 0 255 255 Color39 206 210 1 00 167 0 Colorl6 91 95 255 255 255 255 Color40 211 215 0 40 86 0 216 223 SOUND MODE 11 Color 7 96 100 255 206 143 Jo Color41 216 220 209 219 182 Jo Colorl8 101 105 254 177 153 0 Color42 221 225 42 165 85 0 224 231 SOUND MODE 12 iia SOUND MORE TS coed iis oa ees e e olor 115 5 5 olor4 235 107 240 247 SOUND MODE 14 Color21 116 120 254 121 0 0 Color45 236 240 107 156 231 o 248 255 SOUND MODE 15 Color22 121 125 176 17 0 0 Color46 241 245 165 198 247 o Color23 126 130 96 0 11 0 Color47 246 250 0 0 189 o 1 255 D mn Color24 131 135 234 139 171 o Color48
11. WN buttons to scroll through the DMX Channel modes The Channel modes are listed below To run the 1 Channel Mode press the MODE button until Ch01 ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 12 MEGA GO PAR64 RGBA Operating Instructions is displayed This is the 1 Channel DMX Mode To run the 2 Channel Mode press the MODE button until Ch02 is displayed This is the 2 Channel DMX Mode To run the 4 Channel Mode press the MODE button until Ch04 is displayed This is the 4 Channel DMX Mode To run the 5 Channel Mode press the MODE button until Ch05 is displayed This is the 5 Channel DMX Mode To run the 6 Channel Mode press the MODE button until Ch06 is displayed This is the 6 Channel DMX Mode To run the 7 Channel Mode press the MODE button until Ch07 is displayed This is the 7 Channel DMX Mode To run the 8 Channel Mode press the MODE button until Ch08 is displayed This is the 8 Channel DMX Mode Please see pages 16 19 for DMX values and traits After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX control ler ADJ RFC Remote Control On Off This function is used to activate and deactivate the ADJ RFC Remote Control When this function is activated you can control the fixture using the ADJ RFC Please see page 15 for the controls and func tions 1 Plug the fixture in and press the MODE
12. button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until rFXX is displayed XX repre sents either on or oF 3 Press the UP or DOWN buttons to either activate the remote func tion On or deactivate it Off oS Default Running Mode This is a default running mode When this mode is activated all modes will return to their default settings 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until dEFA is displayed 3 Press the UP and DOWN buttons simultaneously Press the MODE button to exit ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 13 MEGA GO PAR64 RGBA Operating Instructions Battery Life This menu is used to check display the battery life 1 Plug the fixture in and press the MODE button until bXXX is dis played XXX represents a number between 0 100 The number that is displayed is the remaining battery life If b is displayed it means either the battery is dead or your running the unit on AC power MEGA GO PAR64 RGBA Master Slave Configuration Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the con trolling unit and the others will react to the controlling
13. cted between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 0 and interference It is always advisable A p to connect a DMX terminal Resistance XLR Pin Configuration 1 1 2 Cold 1 Ground 1 Pin 1 Ground 1 s e i i Pin 2 Data Compliment negative 1 1 Pin 3 Data True positive and PIN S DMX 4 of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Data Compliment signal Pin 2 Data True signal Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 9 MEGA GO PAR64 RGBA Operating Instructions Operating Power There are two ways to supply power to this unit batte
14. ctive mode The unit will react to sound chasing through the built in programs e Auto Run Mode There are 16 Auto Run programs to choose from Static Color Mode There are 47 colors to choose from e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 10 MEGA GO PAR64 RGBA Operating Instructions as the ADJ Show Designer RGBA Dimmer Mode 1 Plug the fixture in and press the MODE button until 2 When r XXX is displayed you are in Red dimming mode Press the UP and DOWN buttons to adjust intensity 3 When G XXX is displayed you are in Green dimming mode Press the UP and DOWN buttons to adjust intensity 4 When b XXX is displayed you are in Blue dimming mode Press the UP and DOWN buttons to adjust intensity 5 When u XXX is displayed you are in Amber dimming mode Press the UP and DOWN buttons to adjust intensity 6 After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP but ton to enter the Flash strobe mode 7 FS XX will be displayed this is Flash mode The Flash can be adjusted between FS 00 flash off to FS 15 fastest flash Sound Active Mode In this mode the MEGA GO PAR64 RGBA will react to sound and chase through the different colors 1 Plug th
15. e fixture in and press the MODE button until SoXX is dis played XX represents the sound active mode 1 15 currently displayed 2 The fixture will now change via sound 3 Press the SET UP button to adjust the sound sensitivity SJ X should be displayed Use the UP or DOWN buttons to adjust the sensitivity SJ 1 is the lowest sensitivity SJ 8 is the highest Auto Run Mode In this mode the MEGA GO PAR64 RGBA will run 1 of 16 auto pro grams The auto run program can be either a fade program or a sim ple color change program 1 Plug the fixture in and press the MODE button until APXX is dis played XX represents the program number 1 16 currently dis played 2 After you have chosen your desired program you need to decide if you would like the program to fade through colors or simply change Press the SET UP button until either SP XX color ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 11 MEGA GO PAR64 RGBA Operating Instructions change or F XX color fade is displayed 3 If you select color change use the UP and DOWN buttons to adjust the speed between SP 01 slowest and SP 99 fastest Once you have set your desired color change speed press the SET UP button to move on to F XX color fade Use the UP or DOWN buttons to set the color fade speed to F 00 This means the color fade is off and the fixture will now color c
16. e voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The MEGA GO PAR64 RGBA can be controlled via DMX 512 protocol
17. f electrolyte or a gel leakage should be placed away from fire to avoid fire or explosion 4 Battery Storage When storing the battery it should be stored at room tempera ture with a charge of at least 50 We recommend that during long periods of storage that the battery be charged every 6 months Doing this will prolong the life of the battery and will also make sure that the battery charge does not fall below the 30 mark 5 Other Chemical Reaction Because batteries utilize a chemical reaction battery per formance will deteriorate over time even if stored for a long period of time without being used In addition if the various usage conditions such as charge discharge ambient tempera ture etc are not maintained within the specified ranges the ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 6 MEGA GO PAR64 RGBA Battery Precautions life expectancy of the battery maybe shortened or the device in which the battery is used may be damaged by electrolyte gel leakage If the batteries cannot maintain a charge for long periods of time even when they are charged correctly this may indicate it is time to change the battery 6 Battery Disposal Please dispose of battery according to local regulations ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 7 MEGA GO PAR64 RGBA Set Up Power Supply The ADJ MEGA GO PAR64 RGBA contains a auto matic voltage switch which will auto sense th
18. hange at the speed you have set To run the fixture in color fade reverse the instructions Set your color fade speed and set the color change speed to SP 01 Static Color Mode 1 Plug the fixture in and press the MODE button until CLXX is displayed 2 There are 47 colors to choose from Select your desired color by pressing the UP and DOWN buttons After you have selected your desired color you can activate strobing by pressing the SET UP button to enter the Flash strobe mode 3 FS XX will be displayed this is Flash mode The Flash can be adjusted between FS 00 flash off to FS 15 fastest flash DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your fixtures as spot lights The MEGA GO PAR64 RGBA has 7 DMX modes 1 Channel mode 2 Channel mode 4 Channel mode 5 Channel mode 6 Channel mode 7 Channel mode and a 8 Channel mode See pages 16 19 for each modes DMX traits 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 Torun your fixture in DMX mode press the MODE button until d XXX is displayed XXX represents the current displayed ad dress Use the UP or DOWN buttons to select your desired DMX address then press the SETUP button to select your DMX Channel mode 3 Use the UP or DO
19. ife of the battery Try to not let the battery fall below 30 charge Example f b050 is displayed the battery is at half life If b025 is displayed the battery is at 25 life NOTE When the battery is charging or if the battery life is below 30 the digital display will flash NOTE After 20 seconds of inactivity the display will revert back to the battery life display Battery Recharge To recharge the battery plug the supplied AC cord into the AC input on the side of the unit and plug the other end into a matching power supply It takes about 6 5 hours to reach full charge The display will STOP flashing when the unit reaches 100 charge Note When unplugging the unit from charging and then applying power via battery there will be a minimal charge drop For a faster recharge put the Load Switch in the Off position and the Battery Switch in the ON position ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 21 MEGA GO PAR64 RGBA Fuse Replacement Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse MEGA GO PAR64 RGBA Trouble Shooting Listed below are a few common
20. on the web at www adj com for any comments or sugges tions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 2 MEGA GO PAR64 RGBA Features e Rechargeable Lithium Battery e Mulit Colors e Five Operating Modes e Electronic Dimming 0 100 e Built in Microphone e DMX 512 protocol 3 Pin DMX Connection 7 DMX Modes 1 Channel Mode 2 Channel Mode 4 Channel Mode 5 Channel Mode 6 Channel Mode 7 Channel Mode and 8 Channel Mode e ADJ RFC compatiable Not Included Power Cord Daisy Chain See page 14 MEGA GO PAR64 RGBA Warranty Registration The MEGA GO PAR64 RGBA carries a 2 year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the
21. orth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon it s products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer
22. power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed Never plug this unit in to a dimmer pack e Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 22 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power
23. problems the user may encounter with solutions Unit not responding to DMX 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the right connectors it does matter which way the inputs and outputs are connected Unit does not respond to sound 1 Quiet or high pitched sounds will not activate the unit 2 Make sure that Sound Active mode is activated MEGA GO PAR64 RGBA Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew Cleaning ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 22 MEGA GO PAR64 RGBA Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the
24. product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set f
25. ry power or AC power AC Power To run the unit using AC power plug the unit into a power source and put the Load Switch into the ON position When using AC power make sure the Battery Switch is in the OFF position e Battery Power To run the unit using Battery power put the Load and Battery Switches in the ON position LED Display On Off To set the LED display to turn off after 10 seconds press the MODE button until don is displayed press the UP button to display doff Now the display will disappear after 10s Press any button to turn the display on again Be advised though that the display will turn off automatically after 10 seconds To set the display press the MODE button until dXX is displayed Use the UP or DOWN buttons to select either don LED display on at all times doFF LED display shuts off after 10 seconds LED Display Inversion Follow these instructions to flip the display 180 so that the display can be read upside down 1 Plug the fixture in and press the MODE button until dXX is dis played XX represents either on or OFF 2 Press the SET UP button until Stnd is displayed 3 Press the UP or DOWN buttons to reverse the display 180 Operating Modes The MEGA GO PAR64 RGBA has five operating modes RGBA Mode Choose one of the four colors to remain static or adjust the intensity of each color to make your desired color e Sound A
26. supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 4 MEGA GO PAR64 RGBA Battery Precautions 1 Handling of Batteries 1 1 Do Not Short Circuit the Battery Try to never short circuit the battery It generates a very high current which could cause the battery to overheat which may result in electrolyte gel leakage harmful fumes or explosion The LIR tabs may easily short circuit by placing them on con ductive surface A short circuit may lead to heat build up and damage of the battery An appropriate circuitry with PCM is employed to protect accidental short circuit of the battery pack 1 2 Mechanical shock Droping the unit impact hit bending etc may cause failure or shortend life of the LIR battery 3 Other 3 1 Battery connection 1 Direct soldering of wire leads or devices to the battery is strictly prohibited 2 Lead tabs with pre soldered wiring shall be spot welded to the batteries Direct soldering may cause damage of compo nents such as separator and insulator by heat build up 3 2 Prevention of short circuit within a battery pack There is enough insulation layers between wiring and the bat teries to provide extra safety protection
27. t To use the remote you must first activate the fixtures receiver to activate the receiv er please see the instructions on page 13 BLACKOUT Pressing this button will blackout the fixture Press and hold this button for 3 seconds to return to default settings and default running mode AUTO RUN This button will run 1 of 16 automatic programs You can scroll through the 16 programs using the and buttons You can control the speed of the programs by pressing the SPEED button and then pressing the and buttons You can control the fade speed of the Auto Run by pressing the FLASH button and then pressing the and buttons PROGRAM SELECTION This button will activate the static color mode Use the or to scroll through the 47 colors Once you have found your color you can press the Flash Button to activate strobing and use the or to adjust the Flash rate FLASH This button will activate the flash strobe effect or adjust the sound sensitivity while in sound active mode You can adjust the flash speed or sound sensitivity level by pressing the and buttons SPEED Press this button and use the amp buttons to adjust the speed of the Auto run SOUND ACTIVE This button activates sound active mode Use the or to scroll through the 15 sound active programs Press the FLASH button and use the amp
28. units built in programs Any unit can act as a Master or as a Slave however only one unit can be programmed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that the Male XLR connector is the input and the Female XLR connector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 Set the Slave unit to DMX adressing and then connect the Slave unit to the Master 3 Set the Master unit to your desired mode of operation The Slave unit will now follow the Master MEGA GO PAR64 RGBA Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 30 fixtures maximum After 30 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures NOTE Fixtures cannot be power cord daisy chained and run by battery power ADJ Products LLC www adj com MEGA GO PAR64 RGBA User Manual Page 14 MEGA GO PAR64 RGBA ADJ RFC Operation The ADJ RFC remote sold seperately has many different functions and allows you to control your MEGA GO PAR64 RGBA from long distance The ADJ RFC remote can control your system up to 150 f
Download Pdf Manuals
Related Search