FVA 5M1 XS
Contents
1. Oven Thermostat Knob Oven Operation Light Figure Oven Thermostat Light 17 4 2 USING THE OVEN PART OF THE APPLIANCE Oven Function Control Knob To select the desired cooking function turn the knob to the related symbol Figure 3 the details of the oven functions have been explained in Table 1 and next part Oven Thermostat Knob After cooking function set desired temperature can be adjusted by oven thermostat knob figure 4 and oven start to operate timer must be adjusted if available Thermostat signal light will be on or off according to thermostat operation 10 E Figure 3 Figure 4 4 3 USING THE OVEN FUNCTION CONTROL BUTTON Table 1 The oven light the red warning light and the fan will be turned on Performs the function of defrosting the frozen foods The oven s thermostat and warning lights and the lower and upper heating elements will be switched on The oven s thermostat and warning lights the fan and the lower and upper heating elements will be switched on The oven s thermostat and warning lights the grill heater function will be switched on The oven s thermostat and warning lights the upper heating element the grill heater and the fan function will be switched on Availability of the functions explained below vary depending on the product model Defrost Function2. top panel of p Built in oven oven L J m Insert the oven into cabinet by pushing it forward Open the oven door and insert 2 screws in the holes located on the oven frame While the product frame touches the wooden surface of cabinet tighten the screws 7 The dimensions and material of the cabinet in which the oven will be installed must be correct and resistant to increases in temperature In a correct installation contact with electrical or insulated parts must be prevented Insulating parts need to be fitted in a way to ensure that they cannot be removed by using any kind of tool Installing the appliance in the close vicinity of a refrigerator or a deep freezer is not recommended Otherwise the performance of the above mentioned appliances will be negatively affected due to emanating heat After removing your oven from its packaging be sure that the oven is not harmed In case you suspect of any damage to the appliance do not use it immeditely contact Authorized Service 3 3 WIRING AND SAFETY OF BUILT_IN OVEN The instructions given below must be followed without fail during wiring The earthing cable must be connected via the screw with the earthing mark Supply cable connection must be as shown in Figure 6 If there is no earthed outlet conforming to regulations in the installation environment call the Authorized Service immediately The earthed outlet must be in close vicinity of the applianc
3. LITIN O FVA 5M1 XS OPERATING AND INSTALLATION INSTRUCTIONS OF BUILT IN OVEN Dear Customer We take offering quality products more than your expactation as goal offers you the products produced in modern facilities carefully and particularly tested for quality Your manual is prepared in order to help you to use your appliance that is manufactured by the most recent technology with confidence and maximum efficiency Before use of your appliance carefully read this guide that includes the basic information for right and safe installation maintenance and use Contact to the nearest Authorized Service for mounting of your product Contents 1 Presentation and size of product 2 Warnings 3 Preparation for installation and use 4 Using the oven 5 Cleaning and maintenance of your product 6 Service and Transport PART 1 PRESENTATION AND SIZE OF PRODUCT Built in Oven LIST OF COMPONENTS 1 Control panel 8 Wire Grill 2 Handle 9 Racks 3 Oven Door 10 Oven Light 4 Child Lock 11 Turbo Heating Element behind the plate 5 Tray 12 Fan behind the plate 6 Lower Heating Element behind the plate 13 Air Outlet Shutters 7 Upper Heating Element behind the plate PART 2 WARNINGS BEFORE STARTING TO USE THE APPLIANCE PLEASE TAKE ALL ESSENTIAL SAFETY MEASURES AND THROUGHLY READ THE USER MANU
4. Turn your oven s thermostat knob so it will point to this temperature value After a preheating period of 5 minutes put your food into the oven After the cooking turn off the oven function control knob and the thermostat knob and cancel the timer program Take the cooked baked food out of the oven place it on a safe place and ensure that the oven completely cools off by keeping the oven door open As the oven will be hot stay away from the oven and keep your children away as well 12 vvv Grill and Fan Function At this function ensuring complete frying by working together the fan the grill For grills put the foods on the grill and the grill on the highest rack After placing the oven tray on the 3 rack you can start the grill operation The tray placed on the 3 rack will ensure that the oil dropping from the foods will be collected When grilling the oven door must be closed and the oven temperaure should be adjusted to 190 Turn your oven s thermostat knob so it will point to this temperature value After a preheating period of 5 minutes put your foods into the oven After the cooking turn off the oven function control knob and the thermostat knob and cancel the timer program Take the cooked baked food out of the oven place it on a safe place and ensurethat the oven completely cools off by keeping the oven door open As the oven will be hot stay away from the oven and keep your children away as well ENERG
5. You can start the defrost operation by putting the frozen food into oven and bringing the knob to the indicated mark This function does not cook bake the food it only helps defrost it within a short time Put the food to be defrosted on the wire rack that you will place on the third rack support from the bottom Figure 5 To collect the water to accumulate due to the melting ice insert an oven tray into the lower rack Figure 5 11 ES Lower Upper Heating Element Function Static Coking In this type of cooking which is described as the traditional method the heat emanating evenly from the lower and upper resistors into the oven ensures even cooking of the lower and upper side of the food that you are cooking Adjust the thermostat knob of your oven to a temperature recommended on the cooking table for the cooking operation you will perform A preheating of the oven for about 10 minutes is recommended Leave a food to cook which is placed in a suitable container for the recommended duration This position is a preferred function in making cakes sponge cakes pastry baked pasta lasagne pizza After a cooking baking turn off the oven function control knob and the thermostat knob and cancel the timer program if available Take the cooked bake food out of the oven place iton a safe place and ensure that the oven copmletely cools off by keeping the oven door open As the oven will be hot stay away fr
6. AL This appliance has been designed for domestic use as built in furniture After removing the packaging make sure to check if there is any damage to the appliance If there is any damage never attempt to use the appliance and immediately contact your Authorized Service As packaging materials need to be collected immediately and put out of reach The appliance must be installed and put in operation by an authorised technician under the conditions provided by the manufacturer in this manual The manufacturer cannot be held responsible for any damage that might occur due to faulty installation Before connecting your appliance to the mains at home make sure to check the conformity of voltage and gas settings which are specified on the information sticker attached to the appliance and or packaking with the usage conditions available Do not operate the oven before itis fully installed Be sure that all of its buttons are turned off when the appliance is not in use Be sure that the supply cable is not wedged during the installation of the appliance Ifthe supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Before replacing the oven illuminating light turn off the power to the appliance Switch off the appliance before cleaning maintenance work etc Some parts of the appliance may preserve their heat for a long time please wait untill the parts pri
7. LWAYS USE ORIGINAL SPARE PARTS AND CALL ONLY AUTHORIZED SERVICE PERSONNEL SHOULD YOU NEED HELP Pay attention to the following when using your appliance Be careful to connect your appliance to an earthed power outlet or line Do not place the power cord of your appliance near any heated spot Do not pass it near the hob Contact the nearest Authorized Service in the event any damage occurs to the power cord For the models with timers make sure to adjust the time at first run or in case of a power failure Heat and moisture will form in your cooking environment Throughly ventilate your kitchen When you first run your oven a certain smell will be emanated arising from the insulation materials and the heater elements For this reason before using your oven run it empty at maximum temperature for 45 minutes At the same time you need to property ventilate the environment in which the oven is installed Do not touch the interior and the heater when using the oven part of the applianca asit wil be hot After switching off the heater do not touch it with your hand before itis completely cooled off Do not put flammable and combustible materials into the oven Do not place combustibles including any pressured container paper plastic and fabric near the hob surface Be careful when using the oven part of the appliance as the oven surface can be hot Keep children away from the oven While the front door is open do not let children climb
8. Y SAVING During use of electrical cookers itis required to use saucepans having flat bases Choose a cookware of proper size Using a lid will reduce cooking times Minimize the amount of liquid or fat to reduce cooking times When liquid starts boling reduce the temperature setting Oven door should not be opened often during cooking period 13 4 4 USING THE MECHANIC TIMER Mechanical Minute Minder Set the desired cooking time by turning timer button clockwise At the end of this time period timer will make a beep sound but the oven continues working In order to turn the oven off you must take the switch and thermostat of the oven to closed position Figure 6 50 p 30 4 0 Figure 6 14 19 5 UBYOIYO 15901 YIM YOOD NN doyo ERE wu p 1 o o Ee 2 Si 3ddfi 83M01 1 0 08 00 002 811 0 15 4 5 ACCESSORIES USED IN THE OVEN It is recommended that you use the containers indicated on the table depending on the food you will cook in your oven you can also use glass containers cake cutters special oven trays suiatble for use in your oven available in the market Pay attention to the information given by the mufacturer firm concerning this issue If small sized containers are used place this container on the inner grill wire so it will be precisely on the middle of the wire The information given below should be
9. ase Tape the cooker on upper parts hats and heads and saucepan carriers to the cooking panels Place a paper between the upper cover and cooking panel cover the upper cover than tape to the side surfaces of oven Tape carboard or paper onto the front cover on interior glass of oven as it will be suitable to the trays for the wire grill and trays in your oven not damage to the oven s cover during transport Also tape the oven s covers to the side walls If does not have the original Take measure for external surfaces glass and paintes surfaces of oven against possible blows 19 The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 52040966 01 11 ROOO
10. ay Do not move away from the hob while cooking with fat or oil Flaring may occur in case of overheating Never pour water into flaring oil In order to choke the resulting flame close the lid of the pot or the pan and immediately switch off the hob In order to cook in your oven the oven function and temperature setting butttons need to be adjusted and the oven timer if avaible needs to be programmed Otherwise the oven will not operate While the oven door or drawer is open do not place anything on it You may disturb the balance of the appliance or break the door Unplug your appliance when it is not in use Protect your appliance from atmospheric effects Do not leave it under the effects of the sun rain snow dust etc PART 3 PREPARATION FOR INSTALLATION AND USE Manufactured with best quality parts and materials this modern functional and practical oven will meet your needs in all respects Make sure to read the manual to obtain successful results and not to experience any problems in the future The information given below contain rules that are necessary for correct positioning and service operations They should be read without fail especially by the technician who will position the appliance CONTACT THE AUTHORIZED SERVICE FORINSTALLATION OF YOUR OVEN 3 1 CHOOSING A PLACE FOR THE OVEN There are several points to pay attention to when choosing a place for your oven Make sure to take into account our recommendations
11. below in order to prevent any problems and dangerous situations which might occur later When choosing a place for the oven attention should be paid that there are no flammable or combustible materials in the close vicinity such as curtains oil cloth etc which quickly catch fire Furnitures surrounding the oven must be made of materials resistant to heat more than 50 C of the room temperature Required changes to wall cabinets and exhaust fans above the built in combined product as well as minimum heights from the oven board are shown in Figure 1 Accordingly the exhaust fan should be at a minimum height of 65 cm from the hob board If there is no exhaust fan the height should not be less than 70 cm Min 60 cm gt EXHAUST FAN d 3 o I E o io Min 42 cm Min 70 cm Without Hoo Figure 1 3 2 INSTALLATION OF BUILT_IN OVEN Cabinet cut out sizes Eu You can use either cabinet 1 orcabinet2cutoutsizes A DETAIL LI 1 LI 1 LI 1 1 1 1 Li a Minimum 40mm The wooden part be extended up zt to cut out depth M See eee Wooden part 2777 BDETAL 2 2 Countertop Built in hob M M 4 Distance between 25mm countertop d A control panel C DET IL Mounting Control in 50mm 7 Screw N panel Distance between countertop snd 1
12. e Never use an extension cord The supply cable should not contact the product s hot surface In case of any damage to the supply cable make sure to call the Authorized Service The cable must be replaced by the Authorized Service Wiring of the appliance must be performed by the Authorized Service HO5VV F type supply cable must be used Faulty wiring may damage the appliance Such a damage will not be covered under the warranty The appliance is designed to connect to 220 240V electricty is different than the value given above call the Authorized Service immediately The Manucaturer Firm declares that its bears no responsibility whatsover for any kind of damage and loss arising from not complying with safety norms 3 4 WIRING AND SAFETY OF THE FOR BUILT IN OVEN Wiring of the appliance must be performed by the Authorized Service The appliance is designed to connect to 220 240V and 380 415V 3N electricity If the mains electricity is different than the value given above call the Authorized Service immediately Connection of the appliance must be as shown in Figure 2 The appliance is designed for fixed connection to the mains There is to install an all pole disconnector inside they supply circuit with a contact openning of at least 3mm rated 32A delay functioning type BROWN YELLOW GREEN Figure 2 PART 4 USING THE OVEN 4 1 CONTROL PANEL Built_in Oven Oven Function Control Knob Mechanic Timer
13. implemented for enamelled containers If the food to be cooked does not completely cover the oven tray if the food is taken out of the deep freezer or if the tray is used to collect the dripping juices of the foods during the grill operation deformation might be observed on the tray due to high temperatures forming during the cooking frying operation This is normal physical state thay results during the heat transfer Do not leave a glass tray or container in a cold environment immediately after cooking in them Do not place them on cold and wet surfaces Ensure that they slowly cool off placing them on a dry piece of cloth Otherwise the glass tray or container might break If you are going to perform a grill operation in your oven we recommend that use use the grill on tray supplied together with your product if your product includes this equipment This way splattering and dripping oils will not make the oven interior dirty If you are going to use the large wire grill insert a tray into one of the lower racks to avoid accumulation of the oils To make cleaning easier add some water into it as well In a grilling operation use the 3 Orthe 4 rack and ail the grill to prevent the food to be grilled from sticking to the grill rack rack rack rack rack Wire grid Used for grills or placing different containers other than the cooking tray Shallow tray Used for baking pastry
14. ire cleaning However depending on usage it is recommended that you replace them after a certain period of time 5 2 MAINTENANCE Replacing the Oven Light The change of oven lamp must be done by authorized technician The rating of the bulb should be 230V 25Watt Type E14 T300 before changing the lamp the oven should be plugged off and it should be cool The lamp design is specific for the use in household cooking appliances and it is not suitable for household room illumination 18 PART 6 SERVICE AND TRANSPORT 6 1 REQUIREMENTS BEFORE CONTAINING TO SERVICE If the oven does not operate The oven may be plugged off there has been a black out On models fitted with a timer time may not be regulated If the oven does not heat The heat may be not adjusted with oven s heater control switch If the interior lighting lamp does not light The electricitiy must be controlled It must be controlled whether the lamps are defective If they are defective you can change them as following the guide Cooking if lower upper part does not cook equally Control the shelf locations cooking period and heat values according to the manual Except these if you still have any problem with your product please call to the Authorized Service 6 2 INFORMATION RELATED TO TRANSPORT If you need any transport Keep the original case of product and carry it with its original case when need to be carried Follow the transport signs on c
15. marily exposed to heat cool off before touching them Do not keep flammable items substances near the appliance while itis in use When operating other electrical devices near the appliance pay attention that their cables do not come into contact with heated parts When the appliance is not in use make sure that the buttons are in 0 off position Your appliance needs sufficient air circulation while it is operating Carefully read the part of this manual where installation procedures are explained and make sure the relevant conditions are satisfied This operating manual has been prepared jointly for multiple models Some of the specifications explained in the manual may not be included in your appliance Pay attention to the explanations with illustrations while reading the manual 3 During use the appliance becomes hot Care should be taken to avoid touching heating elements inside the oven WARNING Accessible parts may become hot during use Young children should be kept away This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance FOR THE EFFICIENCY AND SAFETY OF THE APPLIANCE WE RECOMMEND THAT YOU A
16. om the oven and keep your children away as well Fan and the Lower Upper Heating Element Function This is the position where the air is coming from the lower and upper heating elements is circulated into the oven by the fan motor and blade Adjust the thermostat knob of your oven to temperature recommended on the cooking table for the cooking operation yo will perform Turn the oven knob so it will point to the symbol of this funtion adjust the oven timer to the recommended time for cooking and preheat the oven for about 10 minutes The food placed in a suitable container is put into the oven and the operation is started This position is position where usually very good results are obtained in baking pastry All parts of the foods will be cooked evenly in this position Suitable for cooking with one tray After the cooking baking turn off the oven function control knob and the temperature setting knob and cancel the timer program if available Take the cooked baked food out of the oven place it on a safe place and ensure that the oven completely cools off by keeping the oven door open As the oven will be hot stay away from the oven and keep your children away as well Grill Function This function is used for grills the grill operation The tray placed on the 3 Rack will ensure that the oil dropping from he foods will be collected When grilling the oven door must be closed and the oven temperature should be adjusted to 190
17. on the door or sit on it The values indicated on the printed documents found the product are values obtained laboratory environment according to relevant standarts These values may vary according to the usage and environment conditions of product Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface which may result in shaterring of the glass Do notuse steam cleaners for cleaning the oven WARNING Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock For hobs the appliance is not intended to be operated by means of an external timer or separate remote control system Once the cooking has been completed the cooling fan continues to operate until the oven has cooled down sufficiently Your appliance is produced in conformity with the relevant safety instructions relating to electrical appliances Maintanance and repair works must be performed only by Authorized Service technicians trained by the manufacturer firm Installation and repair works performed without observing the rules may be dangerous The outer surfaces is heated while your appliance is operating The elements heating the inner surface of the oven and the steam out are extremely hot These sections will continue to preserve their heat for certain while even if the appliance is switched off Never touch the hot surfaces Keep children aw
18. such as flans etc Deep tray Used for baking stews Figure 7 16 Pan anti tilting wire e Tolocate grid correctly in the cavity put it to any rack and push the grid up to the end The pan anti tilting wire must be placed inside ofthe cavitiy PART 5 CLEANING AND MAINTENANCE OF YOUR OVEN 5 1 CLEANING Before starting to clean your oven be sure that all control buttons are off and your appliance is cooled off Unplug the appliance Do not use cleaning materials containing particles that might scratch the enamelled and painted parts of your oven Use cream cleaners or liquid cleaners which do not contain particles As they might ahrm the surfaces do not use caustic creams abrasive cleaning powders rough wire wool or hard tools In the event the excess liquids spilling over your oven should burn it may cause a damage to the enamel Immediately clean up the split liquids Do not use steam cleaners for cleaning the oven Cleaning the interior of the oven Make sure to unplug the oven before starting to clean it You will obtain best results if you clean the oven interior while the oven is slightly warm Wipe your oven with a soft piece of cloth dampened with soap water after each use Then wipe it again this time with a wetted cloth and wipe it dry Acomplete cleaning using dry and powder type cleaners For product with catalytic enamel frames the rear and side walls of the inner frame do not requ
Download Pdf Manuals
Related Search