TECHCONNECT TC2-HDMIW20 OWNERS MANUAL
Contents
1. HDMI Inputs type A 6 HDMI loop though Output type A source select affects this output Only active when Tx powered on 7 IR OUT plug IR blaster cable in here va 5 TC2 HDMIW20_manual_en RECEI VER Rx Mini USB power input 5V 2A 10W HDMI output type A Current Source indicator Source select button Power Button blue when on red when in standby ee a a amp 1 2 VISION a mM REMOTE CONTROL 1 Power Button 2 IR button toggles IR blaster frequency 38 47 56kHz to match source device frequency The default setting is 47kHz On screen display shows current frequency 3 INFO button press to show onscreen diagnostics information Press again to turn off 4 Source select button SOURCE 6 TC2 HDMIW20_manual_en WALL MOUNTI NG The Tx and Rx can be wall mounted DRY WALL INSTRUCTIONS i pi 3 4 DRILL 2 X HOLES IN WALL INSERT PLASTIC RAWL PLUGS INTO HOLES INSERT SCREWS INTO PLUGS LEAVE HEADS PROTRUDING HOOK INTO PLACE 47mm 1 8 7 TC2 HDMIW20_manual_en INSTALLATION Connecting Rx 1 PLUGIN TO POWER 2 CONNECT TO DISPLAY with included HDMI cable 3 TURN DISPLAY ON and select correct input Connecting Tx 1 CONNECT INPUTS from source devices 2 OPTIONAL CONNECT OUTPUT to local display if there is one 3 PLUGIN TO POWER power button backlight changes from red to blue When the Tx is powered on the Rx will automatically come out of stand2. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE All products are designed and imported into the EU by Vision who is wholly owned by Azlan Logistics Ltd Registered in England Nr 04625566 at Lion House 4 Pioneer Business Park Clifton Moor York YO30 4GH WEEE Registration GDOO46SY KoHS C DECLARATI ON OF ORIGI N All Vision products are made in the People s Republic of China PRC 2 TC2 HDMIW20 manual_ en USE ONLY DOMESTIC AC OUTLETS Connecting the unit to an outlet supplying a higher voltage may create a fire hazard HANDLE THE POWER CORD WITH CARE Do not disconnect the plug from the AC outlet by pulling the cord always pull the plug itself Pulling the cord may damage it If you do not intend to use your unit for any considerable length of time unplug the unit Do not place furniture or other heavy objects on the cord and try to avoid dropping heavy objects on it Do not tie a knot in the power cord Not only could the cord be damaged but a short circuit could also be caused with a conseguent fire hazard PLACE OF I NSTALLATI ON Avoid installing this product under the following conditions Moist or humid places e Places exposed to direct sunlight or close to heating equipment Extremely cold locations Places subject to excessive vibration or dust Poorly ventilated places Do not expose this product to dripping or splashing DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS PROD
3. 0 240v AC 50 60Hz 5 volt 2 amp 10 watt DC cable hard wired to transformer with round power connector Transformer integrated into plug Includes interchangeable plugs UK EU US AU DC tail length 1 2 m Transformer dimensions 64 x 41 x 33 mm 2 5 x 1 6 x 1 3 RECEIVER POWER SUPPLY 100 240v AC 50 60Hz 5 volt 2 amp 10 watt USB A socket Transformer integrated into plug Includes interchangeable plugs UK EU US AU Transformer dimensions 64 x 41 x 33 mm 2 5 x 1 6 x 1 3 ACCESSORIES INCLUDED 1 x USB A to 1 35 round pin cable 1 0 m 3 3 ft for transmitter PSU black 1 x USB A to mini USB B cable 450 mm 18 for receiver PSU black 1 x Remote Control with 2 x AAA batteries included black 1 x IR Emitter cable 1 5 m 4 9 ft three diodes black for transmitter 1 x HDMI Cable 1 5 m 4 9 ft black WARRANTY 2 year return to base COMPLIANCES RoHS WEEE CE EMC ORDER PART CODE TC2 HDMIW20 SAP 3223893 15 TC2 HDMIW20_manual_en WARRANTY This product comes with a 2 year return to base warranty effective from the date of purchase This warranty applies only to the original purchaser and is not transferable For the avoidance of doubt this will be taken from the information held by the appointed national distributor at the point of sale If the product is DOA dead on arrival you have 21 days from purchase date to notify the national distributor via your AV reseller The liability of the manufact
4. 76p 1280x720p 50Hz 1280x720p 59 94 60Hz 1920x1080i 50Hz 1920x1080i 59 94 60Hz 1920x1080p 50Hz 1920x1080p 59 94 60Hz 1920x1080p 23 98 24Hz 1920x1080p 25Hz 1080p 24 1920x1080p 29 97 30Hz 640x480 59 94 72 809Hz DVi only VGA 800x600 60 317 72 188Hz DVi only SVGA 1024x768 60 70 069Hz DVi only XGA 1280x768 60 Hz DVi only WXGA 1280x1024 60 Hz DVi only SXGA 1600x1200 60 Hz DVi only UXGA 720p 1080i 1080p 60 11 TC2 HDMIW20_manual_en If Tx LED continues to flash slower than no signal mode and there is no video or video is poor then the resolution is not supported Supported Mandatory CEA 3D Video Format Timings 1280x720p 50Hz Top and Bottom u 1920x1080p 23 98 24Hz Frame packing If the RX status LED continues to flash slower than no signal mode or on screen display shows MER check if display supports 3D format Try switching the 3D video format on the source SUPPORTED AUDI O BIT RATES e Digital Audio from HDMI inputs Up to 6Mbit s bit rate e Supports AC3 and DTS e Supports 2 channel PCM audio 16 24 bits audio sample with 32 96KHz sampling rate ES YES 24 bits Y 12 TC2 HDMIW20_manual_en TROUBLESHOOTI NG If your system is not operating properly please refer to the following information Power indicators not lighting up No video displayed on display e Check if the power plugs of transmitter receiver are
5. UCT MOVING THE UNIT Before moving the unit be sure to pull out the power cord from the AC outlet and disconnect the interconnection cords with other units WARNING SIGNS If you detect an abnormal smell or smoke turn this product off immediately and unplug the power cord Contact your reseller or Vision PACKAGING Save all packing material It is essential for shipping in the event the unit ever needs repair IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY TRADEMARK HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks of HDMI Licensing LLC 3 TC2 HDMIW20_manual_en SPECI AL WARNI NGS Never use this product near an aircraft or medical facility It can cause interference Use of product in the following locations may result in abnormal video and audio output e Product installed in the walls made of concrete e Product situated near refrigerator Microwave oven or other metal items e A cluttered room where the wireless signals may be blocked This product has been tested and manufactured to comply with each country s safety rules however there is no guarantee that interference will not occur in some scenarios If interference happens adjust distance between transmitter and receiver Optimal range between transmitter and receiver is between 2 and 7 meters line of sight This product may interfere 5GHz wireless devices If int
6. ams and or equipment may be made at any time and without notice Such changes will be incorporated into new editions of the User Manual 16 TC2 HDMIW20 manual_ en
7. arance and Personalisation Display Screen Resolution 3 _ Change source on Tx 9 TC2 HDMIW20_manual_en INFO Press INFO button on remote control to see on screen display e Signal Quality e Source e Channel e Resolution NOTE The status of the Tx HDMI output cannot be displayed on the on screen display Press INFO button again to turn on screen display off STATUS INDI CATORS Rx Power Rx Status Rx OSD Display LED LED i off Standby Power saving Solid Red ised i Boot up 15 20 seconds for Flashing Flashing system boot up Blue to i Searching If system can t Flashing Flashing available establish link over 80s Blue reg ge a channels after initialization cs R Wireless No input from selected Solid Blue Flashing linked source Quickly Mode Video format not Solid Blue Flashing recognized Slowly Video format Solid Blue Solid Blue recognized 10 TC2 HDMIW20_manual_en NOTE 1 If link does not establish the transmitter may be out of range Adjust distance between Tx and Rx The maximum video transmission range for 1080p content is up to 20m 66 feet in line of sight LOS The minimum range is 2m 6 5 feet NOTE 3 If no video displayed and on screen display says Not Supported Format adjust resolution and frame rate on source device SUPPORTED RESOLUTI ONS Supported Resolutions Resolution 640x480p 59 94 60Hz 720x480p 59 94Hz 480p 720x480p 60Hz 720x576p 50Hz 5
8. by If the transmitter is powered off the receiver will switch to Standby after 10 minutes automatically Connecting IR Blasters It is possible to point your source remote control at the Rx and it will relay the IR signal back to the source s wirelessly 1 CONNECT IR EMITTER TO TX Cable has 3 x IR emitter diodes inline to control up to three source devices Position them directly over the IR receivers on the source equipment NOTE 1 The IR sensors support 36 56kHz NEC RC5 RC6 signal protocol The default setting is 47kHz Some devices may not be supported 8 TC2 HDMIW20_manual_en OPERATI ON 1 CHECK REMOTE CONTROL Ensure the 2 x AAA batteries are loaded into the remote control 2 TURN POWER ON When mains power is turned on the Tx and Rx will automatically turn on e They can be powered on in any order e f both in standby both need to be turned on manually 3 TURN POWER OFF e Pressing Rx or Remote control power button turns Rx off but leaves Tx on so that the pass through on Tx continues to work io Te oN e Pressing Tx power button will turn both off ot t A lor As soon as they are both on the blue power light will flash for 15 20 seconds while the link is established then it will stay on NOT WORKI NG If you don t have an image ensure 1 Even when there is no link an on screen display will be output from the receiver 2 The computer is set to duplicate or extend the desktop Control Panel Appe
9. erference occurs configure your 5GHz router to 2 4 GHz band only FEDERAL COMMUNI CATI ONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules This equipment generates uses and can radiate radio frequency energy and may in extreme cases cause harmful interference to radio communications If this happens the user should try e Relocating the receiving antenna e Increasing the separation between the equipment and receiver e Connect the equipment to a different power circuit RADIATION EXPOSURE STATEMENT This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body 4 TC2 HDMIW20_manual_en INTRODUCTION This product transmits uncompressed 1080p 60 Hz video and audio content to a display wirelessly It uses 4 9 GHz 5 9 GHz frequencies and it adjusts frequency automatically to avoid interference It has built in Omni directional antennas and transmits up to 20 meters 66 feet LOS Line of sight with no latency TRANSMITTER Tx 1 Current Source indicator 2 Source select button 3 Power standby button blue on red off purple Tx on Rx off f L INJIN i cu MOR 2 4 Power Input 5V 2A 10W with 3 5x1 35 round connector
10. nstallation innovation TECHCONNECT TC2 HDMI W20 OWNERS MANUAL www visionaudiovisual com techconnect tc2 hdmiw20 1 TC2 HDMIW20 manual_ en DECLARATI ON OF CONFORMI TY Where applicable Vision products are certified and comply with all Known local regulations to a CB Certification standard Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries The product described in this owner manual is in compliance with RoHS EU directive 2002 95 EC and WEEE EU directive 2002 96 EC standards This product should be returned to the place of purchase at the end of its useful life for recycling WARNI NGS RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVI CEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL user to the presence of uninsulated dangerous voltage within the product s enclosure that may be h The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the of sufficient magnitude to constitute a risk of electric shock to persons important operating and maintenance servicing instructions in the literature accompanying the 1 The exclamation point within an equilateral triangle is intended to alert the user to the presence of appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
11. properly inserted into a functioning power outlet First steps Check the HDMI connection on the Tx Check the HDMI cable on the RX Select the HDMI as input source on source Check the POWER and INFO lights on Rx Power LED flashing blue OSD displayed S 4 levels looping e Ensure the transmission range is correct POWER LED solid blue slow flashing SOURCE LED OSD displayed BD e Check video resolution and frame rate on source and adjust e Connect source directly to display to check it works POWER LED solid blue STATUS LED flashing quickly OSD displayed i S E e Txis plugged in to source device properly and powered on e Check display setting for your PC have been set to clone mode Projector out mode or dual display mode to enable external display 13 TC2 HDMIW20_manual_en Check video resolution on source device is compatible Poor image guality or Ensure the transmission distance is less than 20m 66 feet line of intermittent video sight Check audio system is not muted and correct input is selected Check PC audio settings to ensure output is set to HDMI out No audio Check PC audio volume Ensure bit rate of audio from the source device can be supported Try re connecting Tx No audio and or video Reboot Tx to re synchronize the display setting when PC resuming Please try to reboot your PC or laptop from sleep Check location of IR emitter It should be line of sight of receiver on sou
12. rce device IR Blaster not Press IR button on remote to change freguency controlling source OSD displayed Be Check the display supports 3D No 3D video output If Rx is connected to AV Receiver check it supports 3D Check the video output setting of Source 3D video format not supported Switch 3D video format to HDMI 1 4a mandatory 3D format 14 TC2 HDMIW20 manual_ en SPECI FI CATI ONS TRANSMITTER DIMENSIONS 182 x 97 x 32 mm 7 2 x 3 8 x 1 3 length x width x height RECEIVER DIMENSIONS 95 x 95 x 32 mm 3 7 x 3 7 x 1 3 length x width x height PRODUCT WEIGHT 400 g 88 Ibs set CONSTRUCTION MATERIAL Plastic COLOUR White TECHNICAL DETAILS Maximum Video Format Supported 1920x1200 1080P 60Hz 3D Data transfer rate 40 Mhz channel 3Gbps 1080P 60Hz Data transfer rate 20 Mhz channel 1 5Gbps 1080P 30Hz Video HDMI 1 3 with HDCP 1 2 Audio Up to 6 Mbps AC3 and DTS 2 Channel PCM 24 bits up to 96kHz Operating Temperature Range 0 40 C Operating Humidity Range lt 80 RH no condensation Transmitter Power Consumption 10 watts Receiver Power Consumption 7 5 watts Latency lt 1ms Maximum distance 20 m 66 feet Encryption 128 bit AES TRANSMITTER CONNECTIVITY 2 x HDMI type A inputs 1 x HDMI type A output 1 x IR OUT Minijack 1 x DC power round pin type RECEIVER CONNECTIVITY 1 x HDMI type A output 1 x DC Power Mini USB B TRANSMITTER POWER SUPPLY 10
13. urer and its appointed service company is limited to the cost of repair and or replacement of the faulty unit under warranty except for death or injury EU85 374 EEC This warranty protects you against the following Failure of any components including the power supply Damage when the product is first removed from its packaging if reported within 24 hours of purchase If you find you do have a problem with this product you should contact the AV reseller you purchased this product from The original purchaser is responsible for shipment of the product to the manufacturer s appointed service centre for repair We will endeavour to return repaired units within 5 working days however this may not always be possible in which case it will be returned as soon as practicably possible In line with our WEEE commitments the manufacturer endeavours to replace the faulty parts of the product rather than replacing the whole unit This warranty does not protect this product against faults caused by abuse misuse incorrect installation unstable or faulty power input which might be caused by ignoring the guidelines set out in this manual LEGAL DISCLAIMER Because we are committed to improving our products the details above may change without prior warning This User Manual is published without warranty and any improvements or changes to the User Manual necessitated by typographical errors inaccuracies of current information or improvements to progr
Download Pdf Manuals
Related Search