Manual SP-4000
Contents
1. DC TO AC POWER INVERTER 4000W DC12V or 24V to AC220V 240V Instruction Manual Please read user manual before use USEFUL APPLICATIONS RUN NOTEBOOK COMPUTERS RADIOS TVS VCRS LAMPS FANS FAX DRILL MICROWAVE OVEN OVEN ETC SPECIFICATION INPUT VOLTAGE RANGE DC 10 15 12 DC 20 30 24V INPUT FULL LOAD CURRENT 400A 12V 200A 24V STANDBY INPUT CURRENT lt 0 9A 12V lt 0 8A 24V OUTPUT VOLTAGE AC 220V 240V OUTPUT WAVEFORM MODIFY SINE WAVE OUTPUT FREQUENCY 50Hz or 60Hz CONTINUE OUTPUT POWER 4000W PEAK OUTPUT POWER 8000W EFFICIENCY 85 90 BATTERY LOW PRE ALARM 10 5 0 5V 12V 21 1V 24V BATTERY LOW SHUTDOWN 10 0 5V 12V 20 1V 24V THERMAL PROTECT 60 5 C MICROCONTROLLER OVERLOAD PROTECT YES MICROCONTROLLER OUTPUT SHORT PROTECT YES MICROCONTROLLER BATTERY EX 12V 24V PROTECT YES MICROCONTROLLER BATTERY POLARITY PROTECT YES BY FUSE FUSE 25A 24PCS 12V 15A 24PCS 24V DIMENSION L W H mm 500 169 152 WEIGHT 10 4 KG TROUBLESHOOTING IF THE INVERTER DOES NOT APPEAR TO BE FUNCTIONING PROPERLY THERE ARE SEVERAL REASONS WHY THE INVERTER MAY NOT BE RESPONDING 1 POOR CONTACT CLEAN CONTACT PARTS THOROUGHLY 2 RECEPTACVLE HAS NO POWER CHECK CAR FUSE REPLACE DAMAGED FUSE CHECK RECEPTACLE WIRING REPAIR IF NECESSARY 3 FUSE IS BLOWN THE FUSE IS LOCATED INSIDE THE P C B REPLACE FUSE WITH A FUSE OF EQUIVALENT VALUE 4 OVE2. RLOAD CAUSED AC OUTPUT REDUCE REDUCE THE WATTAGE OF YOUR LOAD TO LOWER THAN 4000 WATTS 5 THERMAL CAUSED AC OUTPUT REDUCE UNDER HEAVY LOADS FOR EXTENDED PERIODS OF TIME THE AC INVERTER WILL REDUCE OUTPUT TO PREVENT DAMAGE TO EXCESS HEAT IF THIS HAPPENS PLASE PROCEED AS BELOW A SWITCH OFF THE POWER SWITCH OF THIS INVERTER B DECREASE LOAD OF THIS MACHINE I E DISCONNECT SOME OF THE APPLIANCES OR WAIT UNTIL THIS INVERTER BECOME COOL C SWITCH ON THE POWER SWITCH OFF THIS INVERTER 6 LOW BATTERY SHUTDOWN RECHARGE YOUR BATTERY AND RESUME OPERATION CAUTION ALWAYS PLACE THE INVERTER IN AN ENVIRONMENT WHICH IS A WELL VENTILATED B NOT EXPOSED TO DIRECT SUNLIGHT OR HEAT SOURCE C OUT OF REACH FROM CHILDREN D AWAY FROM WATER MOISTURE OIL OR GREASE E AWAY FROM ANY FLAMMABLE SUBSTANCE AC OUTPUT LOAD AND INPUT DCV INDICATOR WITH LED DISPLAY 100 30 ma 15 75 28 14 50 26 13 24 12 25 22 M11 0 20 10 LOAD DCV REMOTE CONTROL TERMINAL OUTLET AC OUTLET 3 POWER SWITCHor 4acs0tz 3 RED AC OUTPUT SOCKET TERMINAL CAUTION DO NOT REVERSE INPUT USE RED BATTERY CORD TO CONNECT OF A DC BATTERY TO TERMINAL AND THEN USE BLACK BATTERY CORD TO CONNECT BATTERY TO TERMINAL coo BATTERY CHASSI
3. S EARTH THE CHASSIS EARTH LUG SHOULD BE CONNECTED TO AN EARTH POINT WHICH WILL VARY DEPENDING ON WHER THE POWER INVERTER IS INSTALLED IN A VEHICLE CONNECT THE CHASSIS GROUND LUG TO THE CHASSIS OF THE VEHICLE IN A BOAT CONNECT TO THE BOAT S GROUD SYSTEM IN A FIXED LOCATION CONNECT TO EARTH 8 gt roma E 5 BLACK SL chassis GROUND LUG WHEN CONNECTED TO ANY APPLIANCE BE SURE TO TURN ON INVERTER FIRST AND THEN TURN ON THE POWER SWITCH OF THE APPLIANCE IF THE TOTAL WATTS OF ELECTRICAL APPLIANCES EXCEEDS THE OUTPUT CAPACITY OF INVERTER OR AFTER OPERATING FOR A PERIOD OF TIME IF THE TEMPERATURE OF THE INVERTER REACHES 60 DEG C THE INVERTER SHALL BE REDUCED AC OUTPUT BY THE PROTECTION CIRCUIT fs E 25 0 A alo 1 WARNING SIGNAL LOW BATTERY PRE ALARM BI Bl OVER HEATING PRE ALARM OVER LOAD PRE ALARM REMOTE CONTROL OPERATION WHEN CONNECTED TO ANY APPLIANCE BE SURE TO TURN ON INVERTER FIRST AND THEN CONNECT WITH THE REMOTE CONTROL WELL AND TURN ON THE SWITCH OF REMOTE CONTROL TURN ON OFF SECONDL
4. Y REMOTE CONTROL POWER ON OFF AC OUTLET Y XWARNING gt FLUORESCENT LAMP DO NOT USE THIS DEVICE WITH FLUORESCENT LAMPS FITTED WITH POWER FACTOR CAPACITORS IF YOU WOULD LIKE TO USE IT PLEASE REMOVE THE POWER FACTOR CAPACITOR FROM FLUORESCENT LAMP BEFORE USING Glow switch a ew mm les er 2 B Lamp ch Power Factor Capacitor Lf BALLASTS
Download Pdf Manuals
Related Search