User`s Manual Rev. Ori
Contents
1. Step B Connect the VGA Cable to the LM VGA port and route the VGA cable through the cable exit hole of KS base stand to the system VGA port on the I O plate Part 12 LM TM 3010 HS for HS Series To mount LM 3010 HS on the back of the terminal please do the following steps to tilt LCD panel Step A Release the top cover on the HS system top I O plate Step Adjust the rear bracket of 2 display to its adequate angle connect one VGA cable end at the 2 display VGA port the other at the VGA port on the top I O plate by routing thru the cable exit hole Apply carefully the 4 small screws that come along with the 2nd display series to the back of this terminal at the screw hole circled in the below picture Step C Close the rear bracket cable cover as illustrated C Note Do not overdo the tightening or unrecoverable thread damage will occur LM TM 3114 3114 B 3115 3115 B Series A TILTING LCD PANEL Please do the following steps to tilt LCD panel Step A Hold and push downward the main unit indicated Part 13 E B Step B Tilt the neck at its right position for most suitable angle for best view effect and convenience in cable connection disconnection B CABLE ROUTING Please do the following steps to remove the cable cover for Gen 7 slim base model Step A Release the base cover Step B Release the base stand neck cover Step C Route the cable to th2. For VGA signals beyond the supported display modes there will be a message Of Range on the middle of screen Maximum supported color depth for 10 and 14 monitor model is 18 bits or 262 144 colors Color depth 15 is 24 bits or Supported display modes are illustrated in the table Part 17 Horizontal Display Resolution Refresh Rate Hz Frequency KHz 640 400 70 37 9 60 31 5 640 480 72 37 9 75 37 5 720 400 70 37 9 56 35 1 60 37 9 800 600 72 481 75 46 9 60 48 4 1024 768 70 56 5 75 60 1366 768 60 47 7 Note Only the LM TM 3014 3114 series is supported for the optimal 1366 768 resolution SPECIFICATION Display LM TM 3014 series LCD Panel 14 TFT LCD Resolution 1366 H x 768 V Active Area mm 309 399 H x 173 952 V Pixel Pitch mm 0 2265 H x 0 2265 V Pixel Arrangement RGB Vertical Stripe Viewing Angle Typical 20 45 45 45 degree U D L R Contrast Ratio Typical 650 1 Response Time Typical 4 ms Rising 6 ms Falling Brightness Typical 200 cd m Touch Touch Type Bezel free resistive for TM3014 Interface USB for TM3014 General Specification Part 18 Display Interface VGA Power Supply 12V from Posiflex terminal VGA port Display LM TM 3015 series LCD Panel 15 0 TFT LCD Resolution 1024 H x 768 V Act
3. manual image settings display for user to manually configure Clock and Phase Phase and clock settings tweak how the VGA analog input of your LCD monitor receives the information coming from your terminal graphics card and optimize screen resolution ES IMAGE PROPERTY There are 2 icons in this submenu mage RGB intensity When this item is selected there will show a customized window display for user to adjust RGB intensity Press button to increase color intensity Press button to decrease color intensity Press OSD EXT to save exit 3 Information Show Resolution Refresh Rate amp Product Details When this item is selected there will show a Part 16 compact product detail about resolution and refresh rate for demonstration e Menu Language Change Language of Menu When this item is selected there will show a multilingual menu for user to opt for desired language option Frangais Italiano MEPR Espa ol LES Deutsch E Menu Position reserved Note This Menu Position is reserved Factory Default When this item is selected there will show a Factory Default menu for user to restore to original monitor settings below E Accessibility When this item is selected there will show an Accessibility menu for user to change menu time out setting EXIT Exit OSD setup with all adjustment saved SUPPORTED DISPLAY MODES
4. 366x768 For XT LM 3014F B pixels series LM 3014F B KS 14 NA d 1024x768 For KS pixels series TM 3014F 14 Yes val 1024x768 For XT TM 3014F B pixels series TM 3014F KS 14 Yes a 1024x768 For KS pixels series TM 3014F B KS 14 Yes JE 1024x768 For KS pixels series LM 3015F KS 9 7 N A Y 1024x768 For KS pixels series LM 3015F B KS 9 7 N A Y 1024x768 For KS pixels series LM 3015F 15 N A a 1024x768 For XT LM 3015F B pixels series LM 3110 9 7 N A Y 1024x768 LM 3110 B pixels TM 3110 9 7 Yes a 1024x768 TM 3110 B pixels LM 3114 14 NA a 1366x768 LM 3114 B pixels TM 3114 14 Yes Pa 1366x768 TM 3114 B pixels LM 3115 15 N A Pa 1024x768 LM 3115 B pixels TM 3115 15 Yes Y 1024x768 TM 3115 B pixels ll FEATURES e Bezel free monitor e High quality TFT LCD panel e Easy maintenance structure allowing easy cleaning and tilt adjustment e VESA mounting supported for all series Part 2 e Support power supply through VGA cable from Posiflex POS Terminal adaptor Power Setup Notice For rear mount device it is designed for use with a Posiflex system In such application it can utilize power support from the Posiflex system Standalone device is equipped with its power CARTON CONTENTS 1 Monitor Touch Monitor VGA cable ON UC User s Manual USB signal cable for TM series only A Posiflex information CD for all TM series Optional DC 12V power adaptor amp power cord IV
5. EL Please do the following steps to tilt LCD panel Step A Hold and push downward the main unit a Step B Tilt the neck at its right position for most suitable angle for best view effect and convenience in cable connection disconnection B CONNECTING ALL CABLES With the LCD monitor touch monitor panel turned to most backward position the main I O connector area will be easily accessible at bottom side of the main unit Please first note orientations of every existing cable connection and then connect every cable properly before any further reconfiguration of cable connections Part 11 C OPENING PLASTIC NECK COVER To route through base please observe the below side view pictures of the base trunk and release the triangle marked hooks to remove the plastic neck cover D CABLE ROUTING IN BASE For cable routing in the mini slim base please refer to the picture below Have all cables pass through the oval hole on the trunk as triangle marked to come out of the arrowed cable exit hole on the base rear side of trunk Then connect all the cables ends to main unit LM TM 3010 KS for KS Series Please do the following steps to install LM TM 3010 KS Step A Fasten the 4 screws onto the upper rear bracket of KS series machine Then Hold the LM 3210 KS monitor with bracket aim to join the upper rear bracket then fasten the 3 screws onto the indicated holes
6. LM TM 30xx 31xx Series POSIFLEX LCD Monitor User s Manual rev ori FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application ABOUT THIS MANUAL This manual assists the user to utilize the Touch Monitor TM LM 30xx 31xx series This product provides exquisite touch control capability over a stable and adjustable LCD monitor with minimal footprint The manufacturer of the LM TM30xx 31xx series monitor heartily apologizes to the user for reserving the right to change or to mod
7. Nevertheless you can also download the Manager from our website 1 Visit us at http www posiflex com and click Support on the main menu bar Part 20
8. PARTS IDENTIFICATION LED INDICATOR STATUS Color Working Stand by Off Status Model LM TM 3010 Series Green Orange None LM TM 3014 Series Green Orange None LM TM 3015 Series Blue Green None LM TM 3110 Series Green Orange None LM TM 3114 Series Green Orange None LM TM 3115 Series Blue Green None LM TM 3010 Series Main Unit mm Display Screen Part 3 LM TM 3014 3114 3114 Series Display Screen LM TM 3015 3115 Series 4 Main Unit 4 mm Display Screen 4 BE LED Indicator B REAR VIEW LM TM 3010 3014 3015 Series VESA Mount Holes OSD Control Hinge Button A utton Area LM TM 3010 3014 3015 Series Joint Bracket for XT series POS system Part 4 LM TM 3010 HS Joint Bracket for HS series POS system LM TM Joint Bracket for KS Stand alone LM TM 3110 3110 B VESA Mount Holes Main Unit Hinge OSD Control Button Area Plastic Neck Cover Base Stand Cable Exit Hole Part 5 Stand alone LM TM 3114 Series VESA Mount Side Mount Cover Holes Hinge OSD Control SS Button Area Plastic Neck Jem Cover Cable Exit Cable Exit Hole Part 6 Stand alone LM TM 3115 Series VESA Mount Side Mount Cover Holes Hinge Plastic Neck Cover OSD Control Button Area _ Base Stand Cable E
9. e circled holes A VI OSD Menu Introduction Power amp OSD buttons The buttons at the right side of LCD monitor are for the OSD On Screen Display control operations and LCD screen power control as in the below picture and are explained below OSD button To enter OSD menu EXT button To Exit the option functions 4 button To increase setting auto tune feature Part 14 D button To decrease setting To turn the monitor power ON OFF Note button indicates an Auto Tune feature to automatically optimize image below utomatic Optimizing image please walt AC11 OSD functions MAIN MENU There are a total of 6 icons in this menu aM oq GI Once one icon is selected it will be displayed in inverted color to indicate its relationship with the submenu below On the physical panel side bar of LCD monitor display pressing EXT button will shift the selected icon one by one from left to right and then wrap around to the leftmost part Press OSD button to enter the selected sub menu Items in sub menu are illustrated below Press to adjust BRIGHTNESS CONTRAST ADJUST SUBMENU There are 2 icons in this submenu BRIGHTNESS ADJUST When this item is selected there will be only the brightness icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to increase brightness intensit
10. ify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com http www posiflex com tw http www posiflexusa com Copyright Posiflex Technology Inc 2014 TRADE MARKS AND SERVICE MARKS C POSIFLEX is a registered trademark of Posiflex Technology Inc P N 196009040 1 0 Other brand and product names are trademarks and registered trademarks and service marks of their respective owners l PRODUCT MODEL NUMBER Model Name Screen Touch Stand Rear Max Resolution MEMO Size Function Alone Cover Supported Mount LM 3010F HS 9 7 N A 1024 768 For HS pixels series LM 3010F B HS 9 7 N A a 1024x768 For HS pixels series LM 3010F KS 9 7 N A a 1024x768 For KS pixels series LM 3010F B KS 9 7 N A a 1024x768 For KS pixels series LM 3010F 9 7 N A fe 1024x768 For XT LM 3010F B pixels series TM 3010F 9 7 Yes Pa 1024x768 For XT TM 3010F B pixels series Part 1 TM 3010F HS 9 7 Yes Y 1024x768 For HS pixels series TM 3010F B HS 9 17 Yes 1024 768 For HS pixels series TM 3010F KS 9 7 Yes d 1024x768 For KS pixels series TM 3010F B KS 9 7 Yes 1024 768 pixels series LM 3014F 14 N A Y 1
11. ive Area mm 304 128 H x 228 096 V Pixel Pitch mm 0 297 H x 0 297 V Pixel Arrangement RGB Vertical Stripe Viewing Angle Typical 80 80 80 80 degree U D L R Contrast Ratio Typical 600 1 Response Time Typical 3 ms Rising 5 ms Falling Brightness Typical 250cd m2 Touch Touch Type Bezel free resistive for TM3015 Interface USB for TM3015 General Specification Display Interface VGA 12V 50W from Posiflex terminal VGA Power Supply port Display LM TM 3010 3110 series LCD Panel 9 7 TFT LCD Resolution 1024 H x 768 V Active Area mm 196 61 H x 147 46 V Pixel Pitch mm 0 192 H x 0 192 V Pixel Arrangement RGB Vertical Stripe Viewing Angle Typical 70 70 70 60 U D L R Part 19 Contrast Ratio Typical 500 1 Response Time Typical 20 ms Rising plus Falling Brightness Typical 270 cd m Touch Touch Type Bezel free resistive for TM3010 3110 Interface USB for TM3010 3110 General Specification Display Interface VGA Power Supply 12V 18W from Posiflex terminal VGA port USB Touch Manager USB Touch Manager for each type of touchscreen is available for user to set up touchscreen functions If your system is preloaded with the OS of your choice the Manager will be installed on your system
12. xit Cable Exit Hole C SIDE VIEW Rear Cover Mount LM TM 3010 3014 3015 Joint Bracket For XT series POS system Part 7 Rear Cover Mount LM TM 3010 HS Joint Bracket For HS series POS system Rear Cover Mount LM TM 3010 KS Joint Bracket For KS series POS system Stand alone LM TM 3110 3110 B Plastic Neck Cover Cover Part 8 E D BOTTOM VIEW Stand alone LM TM 3110 3110 B 3 Rubber Feet E PORT VIEW LM TM 3010 3110 Series DC IN Jack Power LED Indicator LM TM 3114 3014 Series DB 15 VGA Port USB A USB B Audio DCIN Power Type Port Type Port Line In Jack LED Option Indicator Part 9 DB 15 VGA Port LM TM 3015 3115 Series USB A USB B Audio DB 15 VGA Port Type Port Type Port Line In De UN Option V Hardware Installation LM TM 3010 3014 3015 Series for XT Series Please do the following steps to install LM TM 3010 3014 3015 series Step A Place the XT system on a soft pad and align the main unit along table to easily adjust the bracket of 2 LM LCD panel unit to the suitable angle for installation Step B Please locate the 4 holes on the rear side of the host system Step C Adjusting the bracket to the suitable angle please take the 2 LM LCD display bracket aim its 4 holes and tighten the indicated screws to the system Part 10 LM TM 3110 3110 B Series A TILTING LCD PAN
13. y Press button to decrease brightness intensity Press OSD EXT to save exit W CONTRAST ADJUST When this item is selected there will be only the contrast icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to increase contrast intensity Press button to decrease contrast intensity Press OSD EXT to save exit 88 IMAGE POSITION There are 2 icons in this submenu f Horizontal Position When this item is selected there will be only the position icon with an adjustment indication bar for user to adjust Press button to move image rightward for horizontally rightward positioning Press button to move Part 15 image leftward for horizontally leftward positioning Press OSD EXT to save exit Vertical Position When this item is selected there will be only the position icon with an adjustment indication bar for user to adjust Press button to move image upward for vertically upward positioning Press button to move image downward for vertically downward positioning Press OSD EXT to save exit mace SETUP There are 2 icons in this submenu t Image Setup When this item is selected there will show an automatic image setup screen to automatically optimize this image Optimizing imase please wait AC11 El Manual Image Setting When this item is selected there will show a
Download Pdf Manuals
Related Search