DVPro T10 - T2
Contents
1. re BOA Quick Installation Guide at 55 e DVPro T10 T2 Body MODE SELECT e Power cable POWER ACCESS FAIL e Thunderbolt 2 cable O Oo Oo C C e Screw Pack O e Quick Installation Guide e User Manual CD CD R e USB3 Cable Thunderbolt 2 cable lt Side View gt Attention P User Manual J User Manual CD CD R Power cable USB3 cable Installation Guide Overview of Setup method POWER Switch Power ON OFF Switch For Drive installation if needed To facilitate easy configuration of DVT10T2 a LCD Keypad is designed on Follow the below instruction to install or replace disk drive the front panel for parameter setup The default configuration and parameters HDD Access FAIL LED are designed to RAID6 mode To avoid malfunction parameters and configu BLUE Flash upon access Orange ON indicates an error Step 1 Step 2 ration could not be changed on use Open the small door on top of the front When TRAID x RECOVERING 0 shown on LCD i 7 the FAIL LED on means the HDD is under rebuilding Loosen the left side rear screws Use hand or screw driver to loosen panel to manipu2. World s leading Thunderbolt 2 RAID 6 Storage BIOS High Capacity Quiet and High Performance 10 x 3 5 SATA Drive Support a e DVPro T10 T2 Quick Installation Guide Thunderbolt 2 model Warranty Information N Introduction DVPro T10 T2 model This Quick Installation Guide QIG describes the packing content and installation guide line for DVPro T10 T2 Thunderbolt 2 model It also explains the function of each connector and button It is served as a quick startup for basic configuration and the details can be found on User Manual CD R BIOS AP and its resellers are not liable for any data or information lost or possible software error due to adoption of the product We do not take any responsibility of damage and or system eee ewe malfunction due to our product storage device ro Producer Yonezawa Shigeru ee ee e failure or for any of the problems caused as a ublisner nc Quick Installation Guide 6F 6A No 5 Sec 3 New Taipei Blvd Xinzhuang Dist Attention result It is recommended to always backup your New Taipei City 242 Taiwan data Thunderbolt 2 model TEL 886 2 8522 8393 FAX 886 2 8522 8323 Email partner biosap com tw Website www biosap com tw Me J Packing List The box should contain the DVPro T10 T2 and below accessories Name and Function of each part lt Front View gt DVPro T10 T2 Packing List Dy Eron
3. late operational LCD panel lt Rear View gt rear view and open the side panel the thumb screw of disk drive tray POWER LED Power ON LED indicator Begin to use Ko va ACCESS LED There are two ways to configure the DVT10T2 setting either by Web GUI or Host Access LED indicator LCD and keypad operation Most parameters cannot be changed during normal operation to avoid possible corruption or _ 9 DAIL al LED indicat controller error indicator malfunction To start with the parameter setting both ARRAY EARAMETERS OZCZCZEZSRSSOK SETTING DOBBZEO RO RSS Mode and Select buttons have to be pressed and jij O MODE Button hold at power on till the LCD showing Array Parame OaS gt 1 Parameter Initialization Power on Initialization ter Setting i 2 Configure parameters g 3 Stop buzzer alarm Buzzer stopped immediately by pushing one time After then one can change parameters value from Web GUI or LCD button CECROBORORCEORORORCS SELECT Button panel To quickly setup the unit press Mode button to roll among different ES LOLEZA ZOOO Setup Parameter parameters and Select button to choose their values After change press LCD Display Mode and Select at the same time to save modified parameters Er ORE Message display screen Show status of the system For details of each parameter and its meanings please refer to User Manual wearer Show pa
4. le uncompleted data Thunderbolt Connector Thunderbolt 2 for host or cascade INIT Button Get four screws from the screw 4 A Attention Reserved for Controller Setup without front operational panel bag and tightly screw them all e Thuderbolt cannot be enabled while USB3 Fan Module eSATA is enabled Fan 1 e To have each LUN mapping to eSATA and USB3 two LUN mapping and SWAP mode Fan Module should be configured Fan 2 Drive Module Disk Drive module 0 to 9 Upper left one is number 0 and right is 1
5. rameters while doing configuration CD Step 3 Prepare a flat operating table for following operation Put the disk drive perpen diculous to the flat table with the drive connector toward bottom drive connec tor side facing you With thumb screw of drive tray on left hand side slide down the tray carefully till it touches down the flat table RORSRSEEROKO Power Inlet ORG O OROROROROQ OFO AC Power Inlet The default setting might be varied for different configuration upon number ERRER RR of pre installed drives and capacity Following parameters saved please turn S S z OSR ex eSATA3 Connector CBO OB ORE SARASA eSATA 6G host connector off the power then press and hold the Mode button about 3 seconds while BORORORORORORORORORO turning on power to initialize the configured setting New configuration or QR ERO RERERORE ROBE RES USB3 Connector parameters will be effective after initialization process BOSORSEOLCEZOROZOO USB3 host connector BRERERERARERERARER EQ CORO OOOHOO ana aaia EENE Cn OHOO OOOHOO Ethernet Port Attention Initialization process assumes data aligned to its RAID distribution CKO RO KOKORO REKERE KO RJ45 Fast Ethernet port for Web GUI management 5 OK Geox and will enforce current parameters to RAID controller If the unit had corrupt Z ed data during last operation the unit will be treated as normal despite of Thunderbolt Connector Thunderbolt 2 for host or cascade possib
Download Pdf Manuals
Related Search