User Manual - Safe-T-Pull
Contents
1. For your safety NEVER use the Safe T Pull ORIGINAL for pulling on unauthorized products Close the Pin extend the Pin Cylinder to lock in the Truck Hitch Lower the Safe T Pull ORIGINAL so that the springs are not under tension WARNING Leaving the puller arm raised while pulling may damage your centering springs Remove the downed vehicle from its location to a suitable location To hook up back the Safe T Pull Pro under the Truck Hitch Lift the puller arm into the hitch loop and close the latch pin Page 9 of 15 Unhooking e Open the lock pin retract the Pin Cylinder Lower the Safe T Pull ORIGINAL extend the lift cylinder If there is tension between the hook pin of the puller and pulling loop of the Truck Hitch the puller may not lower In this case a decrease in ground speed by the pulling vehicle may be required to free the pulling arm from the Truck Hitch Once the Safe T Pull ORIGINAL is clear of the Truck Hitch raise the pulling arm up retract the lift cylinder to keep it from dragging on the ground Ss ar To unhook open the latch pin lower the puller arm and drive away NOTE Your warranty will be void if you use a Safe T Pull Original with unauthorized products 5 Technical Information Product Maintenance For proper operation ensure the following equipment is in proper operating condition Hydraulic system Check hydraulic fluid in the pulling vehicle to make sure levels are adequa2. stickers should be replaced if worn or unreadable TYPICAL BOTH SIDES 1 5 de t e U nim Presa yo Sranan ae 1 00 1 00 40 00 SAFE T PULL ORIGINAL PULLER STICKER KIT ITEM NO PART NUMBER DESCRIPTION QTY 151 XP 290 STP COMMON PULLER LABEL MOVING HYD 152 J XP 291 STP ORIGINAL PULLER LABEL ORIGINAL LABEL BOM 3 1 5 3 XP 292 STP COMMON PULLER LABEL PINCH POINT SPRING 154 XP 293 STP ORIGINAL PULLER LABEL SERIAL NUMBER Page 13 of 15 7 Troubleshooting and FAQs 1 Does the Safe T Pull ORIGINAL come with everything I need to use it Yes all Safe T Pull products come ready for use On the hydraulic hoses we install 7 pioneer fittings for quick coupling All the required fasteners hardware and hydraulic lines are included NOTE Hydraulic lines will be empty when you receive your Safe T Pull ORIGINAL Fill lines before use 2 What tools will I need to install the Safe T Pull ORIGINAL Recommended tools e Lifting device fork lift skid steer cherry picker e Rubber mallet Sand hammer e 9 16 wrench WARNING All lifting equipment must be rated for 1 000 pounds 453 5kg or more 3 How do I hook up the Safe T Pull ORIGINAL to the tractor e Use a lifting device to align the tongue of the Safe T Pull ORIGINAL into your tractor s drawbar e Slide your tractor s pin into the drawbar a rubber mallet sand hammer may be needed e Push your four 4 hydraulic hoses into your tractor s port
3. this document from Safe T Pull Inc by calling your nearest dealer during their business hours What Is Included e Safe T Pull ORIGINAL Puller Tube e Safe T Pull ORIGINAL Bull Pull Tongue e Two 2 Centering springs Claims If the packaging or the material inside the packaging the product and included accessories appear damaged from shipping or show signs of mishandling upon receipt notify the carrier immediately not Safe T Pull Inc Failure to do so in a timely manner may invalidate your claim with the carrier In addition keep the container and all the packing material for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with Safe T Pull Inc immediately after receiving the merchandise Self contained hydraulics No Vertical Lift No Max pulling load 160 000lbs Shock absorbing mechanism Yes Self centering mechanism Springs and Cables numbers based off grade 5 hardware Page 3 of 15 Contact Us Email sales safe t pull net Mail Safe T Pull P O Box 94 Park River ND 58270 Safety Information Please read the following Safety Notes carefully before working with the product The Notes include important safety information about installation usage and maintenance All personnel working on with or near a Safe T Pull ORIGINAL must wear safety toed shoes safety glasses reflective safety vest protective gloves and hard hat The Sa
4. GINAL Ensure all hydraulic components are in proper working condition on the pulling vehicle Periodically check for oil leaks and worn hoses Keep contaminants from hydraulic oil and replace filters regularly Lubricate cylinder rods with protective lubricant to avoid rusting Page 4 of 15 2 Introduction Product Dimensions Length 9 4 Width 10 Height 2 5 Weight 393lbs 3 Setup Assembly If your Safe T Pull ORIGINAL has been palletized assembly is required After unpacking follow these steps to assembly your Safe T Pull ORIGINAL Unpacking Instructions Before discarding any packaging be sure all included parts are accounted for Remove all strapping and or banding on the package Assembly Steps Slide the tongue assembly into the puller tube assembly and fasten it with four 4 34 bolts lock washers and nuts Note be sure the item isn t upside down See the diagrams below BE SURE THE RING ON THE BULL PULL IS DOWN Installation Recommended Tools Lifting device fork lift skid steer cherry picker WARNING All equipment must be rated for 1 000 pounds 453 5kg or more Page 5 of 15 Installation Instructions e Use a lifting device to align the Bull Pull of the Safe T Pull ORIGINAL between your tractor s drawbar and hammer strap Slide your tractor s pin into the drawbar and lay the opposite end of the puller straight out from the tractor and let it rest upon the ground SU
5. PPORT THIS END WITH LIFTING DEVICE SUPPORT THIS END ON GROUND e Push your four 4 hydraulic hoses into your tractor s ports o CAUTION Ensure that all hydraulic equipment is in proper working order Visit the Safety Information section in this document for more information e Use your tractor s hydraulics to extend the both cylinders fully KEEP OTHERS AWAY Page 6 of 15 e Attach the two blue centering springs to a sturdy location on your tractor It is best to install them 3 up and 3 apart from the Safe T Pull ORIGINAL tongue See diagram below o NOTE The top two mounts on a three point hitch work well 36 DESIRED WIDTH Page 7 of 15 Attach the two ends of the included steel cable through the centering springs using the included cable clamps Be sure the cable is tight and even on both sides to ensure proper alignment Be sure to install the saddle side onto the live end of the cable Unpin the free end of the lift cylinder and insert the steel cable loop into it Replace the pin into the lift cylinder With all personnel clear run the hydraulics to be sure the puller is straight off the back of the tractor when raised If you need to make any adjustments lower the puller all the way to the ground to relieve all spring pressure before you loosen any clamps WARNING Failure to do so can cause serious injury or even death Raise the puller arm and check to make sure the height of the hook pin is high enough for yo
6. SAFESLULE Original User Manual amp Install Guide Safe T Pull Inc Page 1 of 15 TABLE OF CONTINENTS ToBetore YOU BOON aosseti on tM A M putas va S esa adu EU ees C Pie e ed 3 DREO IE SAR Re ee CCE Te PME 3 Wpatisincluded roc PN 3 doro Cn gee ede aie 3 deo fole Uc RETE 4 Sae dWNOtBSo caet wd ted MEM Lem LA ULIS 4 VAN AU O COU CUOM m ER 5 Product DIMCNSIONS iss use a edant dus E aes octamer A AEE 5 DAI 00710 RT ORT eee TERED eT T 5 vtile I 5 Unbdaeknho TDSteU CHIDDS usto oct petri eraot tacta et epe cra lec iet PEU Ed 5 Mistal TON mana UD D 5 AMO DOV OU ON EE Em 9 ODCTOCUOIMNINSTFUCTOINS en 9 5 lechnical Orna ON xoci vetet bemtet ea ttv ERR es E aii 10 Product Manteau doas duel ta esit ipaa E 10 6 Technical SPECICATION S eae esae te bue RUP editis dr et a 11 SDeCITIGOLllOns ss cvv eir n ue d E D iom PU D DIS 11 Replacement Part NUMDETS aao de t ob recta dina a 12 Z Trouble Shooting and FAQS ossis etu esi enis ave ede embed 14 Page 2 of 15 1 Before You Begin Disclaimer The information and specifications contained in this document are subject to change without notice Safe T Pull Inc assumes no responsibility or liability for any errors or omissions that may appear in this manual Safe T Pull Inc reserves the right to update the existing document or to create a new document to correct any errors or omissions You can receive the latest version of
7. TE Freight shipments to some parts of the country may take up to a week or more Page 15 of 15
8. ULL ORIGINAL PULLER ITEM NO PART NUMBER DESCRIPTION EAT P 002 STP ORIGINAL PULLER TUBE WELDMENT CP 003 STP COMMON PULLER LOCKING PIN WELDMENT E E XP 002 STP COMMON PULLER HITCH PIN LOCKING CYLINDER 4 JXP 005 STP ORIGINAL PULLER LIFT CYLINDER m 5 RP 15009 STP ORIGINAL PULLER SPRING BULL PULL MOUNT ASSEMBLY 6 o1 STP ORIGINAL PULLER BULL PULL O 1 7 XP 100 HBOLT 0 7500 10x2 75x1 75 8 XP 101 l1WO75 5 0 0 S 4 9 XP02 HNUTO 7500 10 0 0 4 10 XP 103 HBOLT 1 0000 8x7x2 5 n pe j wio O O 2 L2 xs nro E 13 XP 178 STP COMMON HYDRAULIC HOSE ASSEMBLY 8 LONG W ENDS 14 XP 179 STP COMMON HYDRAULIC HOSE ASSEMBLY 9 LONG W ENDS STP ORIGINAL PULLER SPRING CABLE ASSEMBLY 16 XP 180 STP COMMON HYDRAULIC HOSE ASSEMBLY 10 LONG W ENDS STP COMMON HYDRAULIC HOSE ASSEMBLY 11 LONG W ENDS 18 XP 169 STP ORIGINAL PULLER CABLE SPRING 1500LBS RATED ji jl I P im Page 12 of 15 BOM 2 SAFE T PULL ORIGINAL PULLER SPRING BULL PULL MOUNT ITEM NO PART NUMBER DESCRIPTION RP 15003 STP ORIGINAL PULLER SPRING BULL TONGUE WELDMENT 1 XP 114 STP COMMON PULLER D20 SPRING 353 3 CP 134 STP COMMON PULLER SPRING STOP PLATE 4 CP 15132 STP COMMON PULLER SPRING TONGUE CAP PLATE FP 181 STP PRO PULLER SPRING KEY D20 353 SPRING 6 CP 15180 STP COMMON PULLER 353 SPRING BACK PLATE Warning All
9. ear out faster than others 7 Is there something to cushion the pull The Safe T Pull has a shock absorbing compression spring built into the internals of the pulling arm This technology allows the puller to flex and absorb the jerk upon take off acting like a nylon rope without the dangers and limitations 8 Canlorder replacement parts if something were to wear out Yes Please contact your local dealer or manufacturer representative for ordering your replacement parts Most of our parts are made in house and are in stock 9 How soon can expect my Safe T Pull ORIGINAL Once the order has been placed with your dealer or manufacturer representative we will do our best to get your product to you as quickly as possible Most of our orders will ship same day However during our busy season September thru November production may be backed up by over two weeks To avoid any delays it is best to place orders early NOTE Freight shipments to some parts of the country may take up to a week or more 10 How soon can I expect my Safe T Pull replacement parts Once the order has been placed with your dealer or manufacturer representative we will do our best to get your product to you as quickly as possible All of our replacement parts are in stock and will usually be shipped same day There is a risk of parts being out of stock during our busy season September thru November To avoid any delays it is best to place orders early NO
10. fe T Pull ORIGINAL may raise or lower unexpectedly When servicing the Safe T Pull ORIGINAL be sure the pulling vehicle is OFF and the puller arm is in the lowered position Rules for safe hydraulic operation Park hydraulic machinery where children cannot reach it If your pulling vehicle has hydraulic flow control capabilities usually measured in GPM decrease the flow to 2 GPM This is the minimum amount to operate a Safe T Pull ORIGINAL Block the Safe T Pull ORIGINAL when you must work on the system while raised do not rely solely on the hydraulic lift Avoid servicing the hydraulic system while the machine engine is running Do not remove cylinders until the Safe T Pull ORIGINAL is resting on the ground or securely on safety stands or blocks shut off engine Before disconnecting hydraulic hoses relieve all hydraulic pressure Be sure all hose connections are tight and hoses are not damaged Use a non volatile cleaning solvent to wash parts Three common hydraulic system hazards 1 Burns from very hot high pressure fluid 2 Injuries and illness from flailing hydraulic lines 3 Hydraulic fluid injection into the body Ways to prevent hazards from occurring When attempting to detect pinhole leaks in hydraulic hoses run a piece of cardboard or wood along the hose NEVER touch hydraulic hoses when they are under pressure Never connect a low pressure hose cylinder or other aftermarket equipment to the Safe T Pull ORI
11. s o CAUTION Ensure that all hydraulic equipment is in proper working order Visit the Safety Information section in this document for more information e Use your tractor s hydraulics to extend the lift cylinder e Attach the two included centering springs to a sturdy location on your tractor o NOTE The top two mounts on a three point hitch work well e Attach the two ends of the included steel cable to the centering springs using the included cable clamps e Unpin the free end of the lift cylinder and insert the steel cable into it Replace the pin into the lift cylinder e With the puller arm still lowered adjust the slack in the steel cable until it becomes taught e Be sure to keep hoses and personnel away from all pinch points during operation e Follow all guidelines covered in the Safety Information section of this document 4 My draw bar is only 3 wide with a 1 72 pin will the Safe T Pull ORIGINAL work Yes you will have to use a bushing on your pin to avoid unnecessary wear Page 14 of 15 5 My draw bar is 5 wide with 2 3 4 pin will the Safe T Pull ORIGINAL work Yes you will have to use a 2 pin and use bushings on your drawbar 6 How long should I expect my Safe T Pull ORIGINAL to last Forever The first Safe T Pulls are over 20 years old and are still in use Depending on how well your Safe T Pull ORIGINAL is cared for and how often it is used very few parts will need to be replaced Some replacement parts will w
12. te Check hydraulic hoses for cuts cracks pressure bubbles or other damage NOTE Steel braiding should NEVER be visible Check hydraulic fittings for dents cuts leaks or other signs of damage Check to make sure all hydraulic hoses are securely fastened to their correct fittings Check to make sure all hydraulic cylinders pins are secured with correctly installed hitch clips and or bolts Steel Cable Check to make sure the steel cable is in good condition with no cuts nicks frays or other damage Check to make sure all cable clamps are securely tightened and installed correctly Page 10 of 15 Centering springs e Check to make sure both centering springs are securely fastened e Check to make sure both centering springs are in good physical condition with no cuts scratches or scrapes e Check to make sure the spring is fully retracted without any tension on them When the puller arm is resting on the ground no gap should be visible If any gap is visible your spring has exceeded its maximum weight limit and should be replaced immediately Grease e Grease the Bull Pull hitch 6 Technical Specifications Specifications Dimensions Length 9 4 Width 10 Height 2 5 Weight 383lbs Hydraulic Power Source Pull vehicle System Voltage N A Max psi 3000 psi Page 11 of 15 Replacement Parts Contact your authorized dealer or manufacturer representative to order replacement parts BOM 1 SAFE T P
13. ur application WARNING Keep clear of pinch points when operating Injury or death may occur Page 8 of 15 4 Operation Instructions Pre Operation Maintenance Before every operation of your Safe T Pull ORIGINAL an inspection and pre operation maintenance should be done to ensure all components are in operating order 1 Check hydraulic fluid in the pulling vehicle to make sure levels are adequate 2 Check hydraulic hoses for cuts cracks pressure bubbles or other damage NOTE Steel braiding should NEVER be visible 3 Check hydraulic fittings for dents cuts leaks or other signs of damage Check to make sure all hydraulic hoses are securely fastened to their correct fittings 5 Checkto make sure all hydraulic cylinders pins are secured with correctly installed hitch clips and or bolts 6 Grease the Bull Pull hitch p NOTE f your Safe T Pull ORIGINAL is being used continuously pre operation maintenance should be done before EVERY shift change Operation Instructions Hooking up Be sure ALL persons are clear of the operating area With the Safe T Pull ORIGINAL arm in the lowered position back the pulling vehicle up to the stuck vehicle A decrease in engine RPMs may be necessary for more precise control Once the Safe T Pull OIGINAL s hook pin is directly under the Safe T Pull Truck Hitch pulling loop raise the Safe T Pull ORIGINAL up retract the lift cylinder and into the Truck Hitch pulling loop WARNING
Download Pdf Manuals
Related Search