Gala lineralor s Manual
Contents
1. Sliding Gate Operator User s Manual SL600AC L SL600AC L SLIDING GATE OPERATOR 1 Products introduction please read the instructions carefully before proceeding MCU is supplied to control the gate operator Keypad single button interface Photo beam safety beam interface User can select Auto close function Manual key release design for emergency purposes Gate operator has auto reverse function and the reverse power can change by user 2 Important safety information Carefully read and follow all safety precautions and warning before attempting to install and use this automatic gate operator Make sure the Power supply AC220V or AC110V of the gate operator is suitable for the power supply in your area 3 Main technical parameters Rated output power of motor Remote control operating distance 30m Frequency 433 92mHz Remote control mode Single button Output shaft height 48mm Max gate weight 600Kg Output torque Magnetic limit switch Limit switch Noise lt 56dB Duty cycle S2 15 minutes extra remote control 25 Environmental temperature 20 C 50 C 4 Mechanical Installation The SL600AC L will handle gate weighting up to 600kg and up to 12m if the proper installation procedures have been followed i The SL600AC L gate operator operates by forcing a drive rack by a drive gear The entire configuration is shown in the diagram below The2. light k LED 12 indicate the Open limit switch status if the switch is connected the LED will light All these LED position see the Fig 8 10 Maintenance 11 Check the door once a month The door should be carefully checked for balgnce The door must be in good working order We suggest for safety reasons photocells be used on all gates Disconnect from mains supply before replacing bulb Be sure to read the entire manual before attempting to perform any installation or service to the door operator Our company reserves the right to change the design and specification without prior notification Troubleshooting Solutions Trouble Possible causes The door fails to open and close LED display does not light 1 Make sure that power is ON 2 Replace fuse 1 obstructions 2 Make sure the infrared sensor function is disabling 1 Power is OFF 2 Fuse burn 1 Infrared beam is Remove obstructed 2 Infrared sensor function is enabling but the sensor has not been installed The door can open fails to close 1 Replace the Remote oe level may be battery inside the transmitter does 2 Transmiter code is transmitter not work 2 Reprogram the lost transmitter The transmitter operating distance is too short Battery level may be low Replace battery Packing list f After receiving
3. ok Remote control The remote control works in a single channel mode It has four buttons See Fig 12 Remote transmitter The function of button 1 button 2 button3 are the same and button 4 is pedestrian mode With each press of the remote control button 1 2 and 3 which has been programmed the gate will close stop open or stop cycle Remote Pedestrian button After you learn the transmitter you press the remote button 4 the door will open 1 meter when the door is closed You can program learn button 1 button 2 and button 3 individually If you learn button the button 1 and button 4 are enable if you learn button 2 too the button 2 and button 4 are enable the button 1 is disable Button 4 Fig 12 Remote transmitter Adding extra remote controls Learn Remove the cover press and hold the learn button 1 Fig 8 more than 2 seconds then the LED of LEARN Fig 8 will be on then press the remote control button which you want to use the LED will turn on about 2 seconds and then turn off again The leaming process is finished Up to 25 remote controls may be used Erase remote controls To erase all existing remote controls press and hold learn button S1 the LED of LEARN will turns on release the button until the LED turns off This indicates that all the remote controls have been erased completely Verify open direction If the gate does not move in the desired direction then y
4. the function successfully otherwise repeat the above Setup instruction until your device responds to your expected function 2 If the gate can not be moved please check whether the gate is obstructed or the gate is too weight Activities Covered in this section 5 Remote transmitter With each Press of the button the gate will close stop open or stop cycle Single button mode Three button mode external button switch not supply press OPEN button the gate opens Press STOP button the gate stops Press CLOSE button the gate closes Single button mode external button switch keypad not supply With each press of the button the gate will close stop open or stop cycle Auto close function This feature can be selected to make the gate stay open for some seconds before it automatically closes The auto close time can be adjusted to between 12 24 and 36 seconds Safe guard Infrared photocell If infrared beam is interrupted during Closing the gate will reverse and go Open immediately This feature will not function if the gate is in fully opened and closed positions or during opening Open priority The gate will return to open if press OPEN button of external button switch during closing Limit switch The switch is used to accurately stop the gate in the opened and closed Positions If the gate stops at Opened position when the limit switch is reached the gate will not move if you pr
5. en tighten the chain bolt to the chain bracket Thread up the chain by adjusting the chain bolt Cut the chain to length if necessary Make sure that the chain is Perfectly aligned with the chain holes on the chain box Tighten the chain by tightening the chain bolts at either end See illustration below Fig 5 5 Adjustment SL600AC L SLIDING GATE OPERATOR Magnetic limit switch To ensure safety it is recommended to install limit switches at both ends of the gate to prevent the gate from sliding out of the rails The rails must be installed horizontally install the limit block as shown in Fig 6 The magnetic of limit switch and blocks are used to control the position of the gate i Release the gear with the key and push the sliding gate manually to pre determine the position fix the block to the rack and lock the gear by push up the release bar Moving the gate electrically adjust the block to the proper position until the position of the opening and closing meet the requirement Gate operator Sliding gate SL600AC_ L SLIDING GATE OPERATOR Nut Spring washer Nut M6X65 Fig 6 Manual operation In case of power failure use key unlock the lock and pull down the release bar about 90 degree to open or close gate manually use the release key as follow gt Fit the supplied key in the lock Tum the key and pull down the release bar ab
6. ess OPEN button If the gate stops at closed Position when the limit switch is reached the gate will not move if you press CLOSE buttdn The device is installed with a thermal protector the thermal protector will switch off the motor automatically in case of the temperatur is higher than 120 C and switch on the motor automatically when the temperature is lower than 85 C 5 C Don t stop in the door moving the first circle after power on because the operator learns the position of soft stop 9 LED indicate a LED of Power indicated the input power b LED of LEARN indicated the transmitter learn status c LED 1 indicate the CLOSE external button if the button is pressed the LED will light d LED 2 indicate the OPEN external button if the button is pressed the LED will light e LED 3 indicate the STOP external button if the button is pressed the LED will light f LED 5 indicate the o s c external button if the button is Pressed the LED will light 9 LED 6 indicate the pedestrian switch external button if the button is Pressed the LED will light h LED 7 indicate the infrared Sensor status if the output is connected the LED will light i LED 9 indicate the Loop detector status if the output is connected the LED will light 12 SL600AC L SLIDING GATE OPERATOR j LED 10 indicate the Close limit switch status if the switch is connected the LED will
7. gate operator must be installed on the inside of the gate SL600AC_ L SLIDING GATE OPERATOR WN a x N AAN AAS Chain bracket Input power Fig 1 The SL600AC L Chain driven Gate Operator operates by forcing a Straight piece of chain through its chain box This length of chain is extended between two chain brackets located at opposite ends of the gate The entire Configuration is shown in the pack list Gate preparation Be Sure the gate is properly installed and slides smoothly before installing the SLE00AC L sliding gate operator The gate must be plumb level and move freely Conduit In order to protect the cable use PVC conduit for low voltage power cable and control wires Conduit must be Preset into the concrete when it is Poured Wires within the conduit shall be located or protected so that no damage can result from contact with any rough or sharp part Concrete Pad The base unit of the gate operator requires a concrete Pad in order to maintain Proper stability The concrete pad should be approximately 24 600mm x 12 300mm x 18 460mm deep in order to provide for adequate operation f Once the gate is mounted adequately electrical power is available and the concrete pad is poured you are ready to proceed Anchors You can use the anchors that are provided with the operator 3 anchor bolts 4 anchors washers and nuts These anchors must be set int
8. o the concrete when it is poured or you can use wedge anchors 1 4 x 4 Operator Base Mount the gate operator base to the concrete pad The distance between the gate and the base should be no more than 2 64mm Verify that the operator is leveled properly SL600AC L SLIDING GATE OPERATOR Fig 2 Fig 2A Operator base Operator Mount the gate operator to the base using 4 2 M8x70mm 48 bolts and washers Make sure there is no more than 1 8 2mm of space between the cover and the chain box Check the operator and make sure it is lined up with the gate f Chain Brackets Use the appropriate bolts to attach the chain bracket to the frame of the gate If the gate is of square frame style 3 SL600AC L SLIDING GATE OPERATOR use the square bolts shown bracket Master link Chain bolt Spring washer 8 lut M8 Plain washer 8 Fig 3 If the gate is of round frame Style use the round bolts shown bracket 8 Master link Chain bolt e48 Spring wash jut M8 Spring washer 6 Plain washer 8 Fig 4 Chain Close the gate and attach a chain bolt to the piece of chain that comes with the chain box using enclosure master links Tighten the chain bolt to the bracket with washers and nuts Pull the chain through the chain wheel box to the other chain bracket at the opposite end of the gate Connect the other end of the chain and the chain bolt and _ th
9. ou will need to reverse the motor operating direction open the black plastic cover you can do this by exchanging wires MOT1 and MOT2 Open limit 13 of J5 and Close limit 11 of J5 8 Programming Process SL600AC L SLIDING GATE OPERATOR Adjust the DIP switch see Fig13B and table 1 iva nv Soft start N C limit switch ON ON i 1 Te 2 aA No soft start N O limit switch Fig 13A Fig 13B G8 ioy The autoclose time is 12 sec The autoclose time is 36 sec Doga goy The autoclose time is 24 sec The autociose time is disable Fig 13C Fig 13D Table 1 DIP switch adjust ON see No soft start mode Fig 13A OFF Soft start mode need to power on see Fig 13A reset ON N C limit switch spring limit see Fig 13B 7 Gening tirih OFF Buck N O limit switch magnetic limit SL600AC_ L SLIDING GATE OPERATOR When the 3 and 4 all OFF the Auto close function is disable When the 3 OFF and the 4 is ON auto close time is near 12 Sec when the 3 ON and the 4 is OFF auto close time is near 24 sec when the 3 and the 4 is all in ON Position the auto close time is near 36 sec see Fig 13C OFF see Fig 13D NOTE 1 You must follow the Operating instruction as above any wrong operation is not allowed during setting If your device responds to your requested function correctly you have set
10. out 90 to release the gear Note Do not exceed 90 be Careful not to use too much force otherwise the release bar will be ae Open and close the gate manually Note If the gate bumps the mounting post and cannot be electric opened move the gate a few inches by hand thus you can release the gate with pull the release bar open and close the gate manually dee enn sist sealer E ital m SL600AC L SLIDING GATE OPERATOR Fig 7 6 Wire Connecting Make sure that the power is OFF before making any electrical connections Remove the cover perform the wiring See Fig 8 and wiring notes for contro board and replace the cover again seage Lal q Open limit Close limit IGND COM infared senso 12VDC cong 2SCswitei gt Extral button switch Fig 8 SL600AC_ L SLIDING GATE OPERATOR Wiring notes of control board a Power Input terminal J3 PE Earth L Live N Neutral SL6O0AC L AC220V SL6O0AC L U AC110V b Caution light connect caution light wire to L and N of LAMP terminal J4 SL600AC L AC220V SL600ACU L AC110V c Output power supply 12VDC 7 of J5 COM 9 of J5 I R 8 of J5 is N C Infrared If the infrared beam is interrupted during closing the gate will reverse and open immediately The product is not factory equipped with an infrared device the infrared output signal must be N C From four terminal Form two terminal to the emitter powe
11. r supply to the receiver 12 24V AC DC Terminal J5 T Q 9 i Q JUMP 8 bias 7 p NC OR NO TX Emitter connecting Control board RX Receiver connecting Fig 9 infrared Schematic diagram d Three button switch single button switch keypad The SL600AC is equipped with interfaces for three button switch and single button switch keypad To install the keypad attach one lead of your keypad to 5 of terminal J2 and the other to the 4 COM The keypad will function in single channel mode For three button switch installation use the terminals for multi channel mode Connect open wire of external button switch to 1 OPEN of terminal J2 connect close wire of switch to 2 CLOSE connect stop wire of switch to 3 STOP connect common wire of switch to 4 COM terminal J2 terminal J2 2 Keypad b l 5 _ s 4 3 3 2 Single button 2 1 switch 1 or keypad Three button Control board Control board switch Fig 10A e Pedestrian switch Connect pedestrian switch wire to 4 and 6 terminal of J2 Press the switch the door will open 1 meter when the door is closed SL600AC_ L SLIDING GATE OPERATOR terminal J2 Switch 5 4 3 Pedestrian switch 1 i Control board terminal block Fig 10B Motor and capacitor Terminal J2 J4 MOT COM com MOT1 Positive direction MOT2 Opposite direction PE Protect Earth C and C capacitor If the door move di
12. rection is wrong please change the MOT1 and MOT2 of motor and change the block of limit Magnetic limit switch Terminal J6 terminal J4 Capacitor E Moit Vt ci co T PE Control board Control board terminal block Fig 11 f Loop detector interface Connect wire see the Fig 11A terminal J2 12 4 a 1o detector output LOOP 8 Loop detector Contro board terminal block Fig 11A The car through the loop the door will close itself when the door opened The car atrived the loop the door will reverse when the door closing and the door will auto closed after the car through the loop If the car stops on the loop the door can t close t SL600AC L SLIDING GATE OPERATOR 7 Tuning and operation a Adjust the Adjustable resistance see Fig 8 VR1 For motor working total time adjustment Clockwise rotation to increase counter clockwise rotation to reduce The total time can be set to 10 seconds as minimum and 90 seconds as maximum VR2 For brake force adjustment in limit position Clockwise rotation to increase counter clockwise rotation to reduce Rotate to minimum to cancel brake function in place VR3 For slow stop width adjustment Clockwise rotation to increase counter clockwise rotation to reduce VR4 For motor output force adjustment to keep safe usage Clockwise rotation to increase counter clockwise rotation to reduce Waming Motor force can not be set too large just drive the door is
13. the gate operator you should make an unpack inspection in which you should check whether the product was damaged If you have any problem please contact our dealer You should find the following items in our standard packing o em foa a s a operator OC 4 ot User s manual
Download Pdf Manuals
Related Search