BMW09 - Sonic Electronix
Contents
1. However true Accessory power is very hard to find in this vehicle which is why the Nav TV CAN 2 Accessory C2A module is extremely useful for providing a source of true Accessory power for the BMW09 module 3 Page Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse of its product If you do not agree please discontinue use immediately and return product to place of purchase This product is intended for off road use and passenger entertainment only2. BMWO09 8 18 2010 Rev 1 0 Tony Yankovsky 100 NW 11 Street Boca Raton FL 33432 Tel 561 955 9770 Fax 561 955 9760 www nav tv com info nav tv com Interfacing the future BMW09 Video and camera integration for new 2009 and up iDrive CIC equipped BMW vehicles What s in the box Package Contents BMW0O9 Interface module ee eee o aa am Baa ees Power harness ama LCD out harness OSD keyboard OSD keyboard harness RGB NAVI harness Mode button and harness Optional for source select A V harness Note that due to manufacturing differences some harnesses and connectors may not appear exactly as pictured but the module will operate as stated Screen Removal Remove 2 Torx T10 screws at the top of the screen unit as shown circled in the accompanying photo Once the screws are removed there will be a gap between the top of the screen unit and the dashboard Push a small screwdriver gently into this gap and the screen should come out of its mounting with virtually no force Place a soft covering over the face of the screen and turn it over Remove the video harness from the side of the screen as shown circled in the accompanying photo The other harness is where the CAN connection will be made as well as the power connection for the optional CAN 2 Accessory module 1 Page Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misu
3. ble for misuse of its product If you do not agree please discontinue use immediately and return product to place of purchase This product is intended for off road use and passenger entertainment only OSD Keyboard functions OSD Keyboard Menu OSD Menu SEL Select source change UP Move up through menus Down Move down through menus Factory Mode This is not necessary in most installations however if certain settings need to be changed activate the video camera mode first then quickly press UP gt DOWN gt UP gt Menu in sequence and verify that Menu of Menu of FACTORY FACTORY see photo appears on the AR screen Ifa different Menu appears press Menu to exit then try pressing the keys quicker The main function of Factory Mode is to select the Reverse camera detection method between CAN default and the Gray wire Experimentation with the other functions is not encouraged as it may set a mode that may be difficult to recover from To change the Reverse detection a Enter the Factory Mode S NAVI MODEL Press the DOWN button to highlight BR eerie UTIL then press SEL FACTORY RESET Press DOWN until REAR SELECT is highlighted then press SEL Press DOWN then press SEL Press MENU twice to clear the menu MENU to Return SEL to Select from the screen LED Indicators v LED 1 is illuminated when the module is receiving power v LED 2 is illuminated when a video source or camera i
4. s in order Set the switches Up to enable the appropriate inputs or Down to disable them For instance if AV1 and AV2 are desired switches 2 and 3 should be up while 1 and 4 should be down Switch 5 Screen select Up is correct for most vehicles but if an image does not appear correctly or at all set this switch down Switch 6 Currently not used leave in the Up position Switch 7 Rear camera If a rear camera is being added set this switch Down otherwise set it Up Switch 8 Currently not used leave in the Up position Power connector pinout ACE Bw 1E GND Ch H i des laa pi CARL F CAKA CAET PO SAFE J oa LA REAR C Pin 1 Acc Red 12v accessory power Pin 2 Ground Black Pins 3 amp 4 CAN Hi Greeen Brown amp Low Green Optional Connect as per Step 5 of the Installation Instructions above Pins 5 amp 6 Not used Orange Purple Pin 7 Rear Gray If CAN will not be connected or does not work reliably connect to Reverse lights for backup camera and follow the procedure under OSD Keyboard to change the Reverse detection Source Select gt Press the Mode button to toggle through all available video inputs gt If CAN is connected hold the MENU button on the iDrive or steering wheel Down arrow for 3 seconds 2 Page Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held lia
5. s selected and video is present CAN Operation optional 1 Camera is automatically activated when the vehicle is in Reverse Gray wire is not needed Note Due to the enormous amount of CAN messages in the vehicle this function will not work reliably if any doors are open When testing the reverse camera operation over CAN please ensure that all doors are closed 2 Video source can be changed by holding either the iDrive Menu button or the steering wheel Down button for 3 seconds 3 On most vehicles split screen can be selected by holding the circle button on the steering wheel for 3 seconds while video camera is displayed This only needs to be done once then the setting is saved Note that some vehicles have a different button in that location right side of the wheel lower left button which should have the same function with this module On the 7 Series the Down arrow on the iDrive is used instead B PIP Operation with Parking Sensors PDC If the vehicle is equipped with parking sensors the module can provide a combination of sensors and camera on the screen When in camera mode the split screen button see above will cycle through various on screen combinations of Camera amp PDC as well as displaying only one of the two modes Note about Accessory Power Since the entertainment system in these vehicles can be on when the key is off it is important to use Accessory power when connecting something other than a camera
6. se of its product If you do not agree please discontinue use immediately and return product to place of purchase This product is intended for off road use and passenger entertainment only BMWO09 Interface Connectors S LED Mode gt LCD Out LCD In Power CAN RGB In A V In Out ENF Dipswitches _ SD Keyboard Installation Plug in the video cable from the vehicle into the LCD In port on the BMWO9 interface Connect the round LCD cable supplied with the BMWO 9 into the LCD Out port on the BMWO09 Connect the other end of the round LCD cable plug into the port on the navigation screen where the factory video cable was connected Connect the Black Ground wire leading from the main power harness of the BMW09 to chassis ground Connect the Red Acc 12v wire to a 12v accessory power source or Nav TV s CAN 2 Accessory module Optional but recommended Connect the CAN Hi and Low wires to the CAN wires on the screen s Power and CAN harness The vehicle s CAN wires are Orange Green Hi and Green Low NOTE Strip back the 2 CAN wires and wrap and solder the 2 CAN wires from the BMWO0O9 harness to the vehicle s CAN wires DO NOT CUT THE VEHICLE S CAN WIRES THIS MAY CAUSE CAN CORRUPTION IN THE VEHICLE Dip Switch settings 2 ne ne ee ee oe Disconnect BMW0O9 Power plug before making any DIP switch changes Switches 1 4 These switches enable disable the module s RGB and video input
Download Pdf Manuals
Related Search