USER`S MANUAL CCTV TesterPro
Contents
1. Note a Don t input any power into the DC12 1A OUTPUT port of the CCTV tester to avoid destroy Page 20 Ver STP28V1 1 CCTV testerPRO User s Manual b Don t output this DC12V 1A power to the power input port of the CCTV tester to avoid destroy C When the requirement of the camera is higher than 1A the CCTV tester will enter protection mode Disconnect all the connections of the CCTV tester and then connect the CCTV tester with power adaptor to resume the CCTV tester 5 Audio input test Test the audio input from pickup devices AUDIO IN Connect the tester and pickup device with the gt aa Py Speaker audio cable Ver STP28V 1 1 Page 21 CCTV testerPRO User s Manual 6 Specification MODEL Signal mode Display LCD adjustment Video IN OUT Video Output Mode Video Level test Video signals measured in IRE or mV Communication Compatible with more than 20 protocols such as PELCO D P Samsung PTZ Protocol a Panasonic Lilin Yaan etc Baud Rate 150 300 600 1200 2400 4800 9600 19200bps Color bar generation Test UTP cable connection status and display in the screen Read UTP cable test the number of the test box Low Consumption Energy saving technology Working Temperature 10 C 50 C Working Humidity 30 90 Dimension Weight 166mmx95mmx48mm 293 Page 22 Ver STP28V1 1 CCTV testerPRO User s Manual The data above is only for reference and any change of them will not b2. L PIZ control ler TI e i 5 Video setting y ColorBar generator Cable tester Data monitor aia Device setting e E L 6 x l j 9 MODE SET POWER H 8 H 40 ENTER RETURN Ea AR 11 j OPEN CLOSE J 16 ae T 9 4 9 7 43 J b FAR NEAR 17 Y x RLE TT s Ws WIDE reve Ll 19 42 z TT S med f ze i 5 20 J CCTV Security Tester Pro Page 6 Ver STP28V1 1 The data reception indicator it lights red while the data is being received The data transmission indicator it lights red while the data is being transmitted The charge indicator it lights red while the battery is being charged As the charging is complete the indicator turns off automatically The display Icon of battery electricity it displays the electric quantity Main menu it shows main functions of CCTV testerPRO CCTV testerPRO User s Manual Sub menu Shows and sets the values of functions Long pressing it more than 2 seconds to turn on off the tester short pressing to turn on off the PTZ controller menu displaying Menu key it pops up the main menu constant press it or press the 3 or LY key can shift between functions Setup key press it or press left or right key to enter sub menu to set the parameters of functions Upward Select the item which will be set or add the value
3. Port a Baud b Press the or LX key to select the parameter Address Pan speed which we want to change the value TiltSpeed Set PS Get PS c Press ENTER key to save the change or press RETURN key to give up the change d Press SET key to exit the sub menu e Press POWER key to full screen the image Ver STP28V1 1 Page 13 CCTV testerPRO User s Manual A Protocol Select the protocol according to the protocol of the PTZ camera Up to 21 popular protocols are available like elco P Pelco D Samsung Yaan LiLin CSR600 etc B Port Select the communication port for the PTZ camera controlling RS232 422 485 C Baud Select the baudrate according to baudrate of the PTZ camera 150 300 19200bps D Address Set the ID according the ID of PTZ camera 0 254 E Pan Speed Set the pan speed of PTZ camera 0 63 F TiltSpeed Set the tilt speed of PTZ camera 0 63 G Set PS Setup preset position 0 128 a P T Z the camera to desired position b Press SET key to enter PTZ controller submenu c Move the yellow cursor to Set PS and then press lt 1 or gt key to select the preset position number d Press ENTER key to complete preset position setting or preset RETURN key to give up preset position setting Tips Press gt or lt 1 key to accelerate the value changing H Go PS Call the preset position 0 128 The PTZ camera will go to the desired preset position a Move the yellow curs
4. connecting condition and the sequence of wires will be 1 3 2 6 3 1 4 4 5 5 6 2 7 7 00 displayed as well as the serial number of the cable tester kit Data monitor r 5 Data Monitor Port 485 Baud 4800 EPs oG a Captures the protocol from the controlling system and display AO 00 00 00 00 Beha Ne O do cas command data It is helpful to debug and maintain RS485 AO 00 00 04 40 00 AO 00 00 00 00 0 communication AO 00 00 40 00 AQ 00 00 00 00 6 Device setting Auto poweroff Set the parameters of the CCTV testerPRO Auto poweroff Keypad tone Language English Brichtness 7 Keypad tone Language Brightness Not saved Enter to apply Page 12 Ver STP28V1 1 CCTV testerPRO User s Manual 3 3 PTZ Controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position The following connections should be confirmed before use a The Video In interface of the CCTV testerPRO and the output interface of camera b Data A of the CCTV testerPRO and A of the PTZ camera or controlling device data B of the instrument and B of the PTZ camera or controlling device Note Don t connect communications interface with a circuit the voltage higher than 6V L S D y G gt 4 y e V PTZ controller a Press SET key to enter the sub menu of PTZ controller
5. on Continuously press at least 2 seconds to power on off the CCTV testerPRO When the CCTV testerPRO is powered on press MODE key the main menu will pop up Colorbar generator Cable tester Data monitor Device setting NO video input 3 2 Menu amp Functions Press MODE key continuously or press the A or 154 key to select the function PTZ controller Video settings Colorbar generator LAN cable tester Data monitors Device setting and enter corresponding function setting sub menu Press SET key to set the parameters in function sub menu Note When the CCTV testerPRO is powered on it will return to the function which is being operated before it is turned off PTZ controller 1 PTZ controller Display the input video images Pan tilt the P T unit and zoom in out the image Setup the controlling parameters like protocol communication port baud rate PTZ ID pan tilt speed set and call preset position Baud Address Pan Speed Tilt Speed Set PS Go PS Ver STP28V1 1 Page 11 CCTV testerPRO User s Manual 2 Video setting Adjust the LCD brightness Contrast Color saturation Contrast Saturation Video Format displaying and Video level testing Colorbar generator 3 Colorbar generator Output or receive seven different forms of video color bar to tester monitor cable or other equipment Cable tester 4 Cable tester Test LAN cable or telephone cable Remote kit c The
6. t use the detergent to clean and the dry cloth is suggested to use If the dirt is not easy to remove the soft cloth with water or neutral detergent can be used but the cloth should be tweaked sufficiently Ver STP28V1 1 Page 3 CCTV testerPRO User s Manual 2 Introduction The CCTV testerPRO is developed for the On Site installation and maintenance of video monitoring system It can be used for displaying video controlling PTZ generating images capturing data of RS485 and testing LAN cable etc Its functions easy operation and portability makes it simple for the CCTV technician to install and maintain CCTV system improving work efficiency and get the labor cost down 2 1 Features B 2 8 TFT LCD 960 H x240 V resolution Video Level testing video signals measured in IRE or mV DC12V 1A power output for camera Audio input test testing the audio signal from pickup devices PTZ control Pan tilts the P T unit zooms in out the lens adjusts the focus aperture and sets and calls the preset position B Video displaying Automatically adapts and displays the video format of NTSC PAL LCD Brightness Contrast Color Saturation are adjustable W Video Generating The PAL NTSC multi system colorbar video generator seven system switchable transmit receive seven system colorful imagines B Data analyst Captures and analyzes RS485 controlling data to help the technician to find out the problem B Cable testing It is p
7. USER S MANUAL CCTV TesterPro Ver STP28V1 1 2009 5 CCTV testerPRO User s Manual Thank you for purchasing the CCTV security tester Please read the manual before using the CCTV testerPRO and use properly For using the CCTV testerPRO safely please first read the Safety Information carefully in the manual The manual should be kept well in case of reference Keep the S N label for after sale service within warranty period Product without S N label will be charged for repair service If there is any question or problem while using the CCTV testerPRO or damages occurred on the product please contact our technical Department Ver STP28V1 1 Page 1 CCTV testerPRO User s Manual Table of Content 1 Safety Information ei nner nner 3 2 H Ras L BL UNO Ns E AA e 4 Qo T Ie 4 2 2 CCTV testerP RO KIIS saracsrassnantnantcnnnnnrannanere ere sere e io encantada 5 2 97 Front Pag settee ences e a S A EEEE 6 2A L LR 8 20 Installing the Batlerye 5 2222 e eae ARS 9 3 OPC hallo Near EEE ARS 11 Sol POWER OM OM a sae betes 11 Soe Menu Se IF UNCIIOINS ZEE SERRE EE 11 39 RTZ CO Moller iS 13 cr LS LR T e EOS 16 3 0 Colorb r generator SS SR REEE EEE EEE 16 3 0 Cable UGS TGT EE ERT EE 17 Of Wald MORMON sasesssssesessse eases ROSAS RARE 18 3 6 Device seting r re e A ann sana nnnaseanrereaneddncss 18 39 Address SGT Haara SEH 19 4 DG 12V POWER Output r seer one ananassae 20 S Audi
8. automatically change between NTSC and PAL and the Video Level will automatically change between IRE Institute of Radio Engineers and mV NTSC signals measured in IRE units PAL signals measured in mV The Video Level should be within the indicated range Levels that are too low will result in a dim picture with reduced dynamic range A Video Level that is too high will result in washed out pictures with decreased The CCTV testerPRO will display Normal when video levels are 1000mV 20 Exceed or Weak will be displayed when video level out of 1000mV 20 3 5 Colorbar generator Output video at any mode Output or receive seven different forms of video color bar to test monitor video cable or other equipment Colorbar generator Page 16 Ver STP28V1 1 CCTV testerPRO User s Manual a oil key to select the parameter which we want to change the value b Press the LX J key to change the value c Press ENTER key to save the change or press RETURN key to give up the change 3 6 Cable Tester Test LAN cable or telephone cable Connect LAN cable or telephone cable with the CCTV testerPRO and cable tester And then the connecting status cable type and the sequence of wires will be displayed as well as the serial number of the cable tester kit Cable tester co Y Cable tester Cable tester R TT Cable tester d EEN 3S DONA WH On Wh D NO 00 wn 0 4 GD KP La KM A Cable Crossed ethe
9. e auto running functions by calling preset position effective for some brands of PTZ camera Call preset 33 Open Auto flip function Call preset 34 Reset zero point of PTZ camera Call preset 64 Enter the main menu of the PTZ camera Call preset 95 Enter the main menu of the PTZ camera or stop the PATTERN recording Call preset 96 Run pattern 1 Call preset 97 Run preset tour 1 Call preset 98 Run frame Scan Call preset 99 Run Auto scan Go PS 4 098 Go PS e 099 Ver STP28V 1 1 Run Frame scanning Call the preset point 098 Run Auto scanning Call the preset point 099 Page 15 CCTV testerPRO User s Manual 3 4 Video Setting User can customize the brightness contrast and saturation of the LCD according to the using environment the CCTV tester auto display the format PAL NTSC of video input and analysis the input video signal level Contrast Saturation a Press the A or key to select the parameter which we want to change the value b Press the or gt key to change the value Press ENTER key to save the change or press RETUR key to give up the change c The Video Format and Video Level will be displayed in the lower portion of the screen If there is no video signal at the Video IN port of the CCTV TesterPRO the type of NTSC or PAL and Video Level will not be displayed Depending on the type of camera connected to the CCTV testerPRO the Video Format will
10. e informed in advance For more detailed technical inquiries please feel free to call the Technical Department of our company Products certification C Fe Ver STP28V1 1 Page 23
11. o Input 1 tent meenn are seater AAARARNAAS 21 G Specifications EEE 22 Page 2 Ver STP28V1 1 CCTV testerPRO User s Manual 1 Safety Information Notice B The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital gas station etc To prevent the functional decline or failure the product should not be sprinkled or damped The exposed part of the tester should not be touched by the dust and liquid During transportation and use it is highly recommended to avoid the violent collision and vibration of the tester lest damaging components and causing failure Don t leave the tester alone while charging and recharging If the battery is found severely hot the tester should be powered off from the electric source at once The test should not be charged over 8 hours Don t use the tester where the humidity is high Once the tester is damp power off immediately and move away other cables connected The tester should not be use in the environment with the flammable gas Do not disassembly the instrument since no component inside can be repaired by the user If the disassembly is necessary indeed please contact with the technician of our company The instrument should not be used under the environment with strong electromagnetic interference Don t touch the tester with wet hands or waterish things Don
12. of the parameter Tilt the PTZ upward Leftward Enter the sub menu or select the parameter whose value will be changed Reduce the value of the parameter Pan the PTZ left Rightward Enter the sub menu or select the parameter whose value will be changed Add the value of the parameter Pan the PTZ right Downward Select the item which will be set or reduce the value of the parameter Tilt the PTZ downward Confirm Open Confirm the setting of parameters open the aperture Return Close Return or cancel while setting parameters of the menu close the aperture Near focus Focus the image nearby Far focus Focus the image faraway TELE zoom in the image Ver STP28V 1 1 Page 7 CCTV testerPRO User s Manual 2 4 Side view S w Top View Right Side DC12V1A power output output DC12V power for camera 2 2 2 2 2 2 2 2 3 4 5 l 7 8 9 l 30 Video output BNC output interface Outputs the video 2 Video input BNC input interface Inputs the video 31 RS485 422 Interface RS485 RS422 communication for the PTZ Page 8 Ver STP28V1 1 CCTV testerPRO User s Manual 2 5 Installing the Battery The tester has built in lithium ion polymer rechargeable battery The battery cable inside battery cabin should be disconnected for safety during transportation s gt Prior to the use of the instrument
13. or to Go PS and then press lt or 5 key to select the preset position number b Press ENTER key to complete preset position calling or preset RETURN key to give up preset position calling Tips Press gt or lt key to accelerate the value changing The way of calling the OSD menu and preset of the PTZ camera may vary with control systems from different manufacturers Please read the operation manual of control system manufacturer for details The way of calling OSD provided for reference is calling preset 64 a Move the yellow cursor to PTZ controller to enter PTZ controller mode b Press SET key to enter PTZ controller sub menu Press A or ka key to move the yellow cursor to Go PS Page 14 Ver STP28V1 1 CCTV testerPRO User s Manual C Press lt or gt key to select the preset number 64 and then press ENTER key to call OSD menu of the PTZ controller Go PS E 064 OSD Menu of Dome For reference only MAIN MENU DISPLAY SETUP CAMERA SETUP CONTROL SETUP CAMERA MASK SET PROGRAM PAL CAMERA CAM DEFAULT SET DOME RESET EXIT 1 2 3 4 5 6 7 8 9 O o NN AU A UU Nel OSD menu of dome Call the preset point 064 MAIN MENU Display configuration Set camera parameters Set PTZ controlling Set privacy mask Set auto running functions PAL NTSC Switch Restore the default settings Reset the dome Exit the main menu 8 Operat
14. owerful in testing LAN cable measuring the connecting status displaying the sequence of connection and the NO of the LAN cable B Miulti interface and Multi baudrate Support RS232 RS485 and RS422 interface baud rate ranging from 150 600 to 19200bps B Multi protocol Supports more than twenty PTZ protocols For example PELCO P PELCO D SAMSUNG etc PTZ address scanning search up the ID of PTZ camera Lithium Ion Polymer Battery 3 7V DC2800mAh The device employs advanced power control and protection circuit The device is high power efficient energy saving and environmental protection It can last 15 hours for normal use after charging for 4 hours Page 4 Ver STP28V1 1 CCTV testerPRO User s Manual 2 2 CCTV testerPRO Kits Professional design light and portability video display and data control are deliberately integrated which makes the instrument so simple practicable easy for use that the training is almost unnecessary for an operator to be skillful 1 CCTV testerPRO 3 LAN Cable Tester 5 BNC Cable 6 Safety cord 7 RS485 data cable Lithium Ion Polymer Battery 8 Instruction Manual 2 Power Supply 5V 2A Ver STP28V1 1 Page 5 CCTV testerPRO User s Manual 2 3 Front Panel 3 2 se 7 1 4 h lt I gt R gt xB E CCTV TesterPro 7
15. rching up WIDE The tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning Ver STP28V 1 1 Page 19 CCTV testerPRO User s Manual FAR The tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Press button the tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up Press re manual single step decreasing button the tester will search up the ID step by step from 256 to 1 When the ID is searched the PTZ camera will stop panning Press button the tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop searching up Press manual single step incremental button the tester will search up the ID step by step from 1 to 256 When the ID is searched the PTZ camera will stop panning Press the direction control button to adjust Speed Dome Camera preset button to quit from the address scanning function menu 4 DC12V 1A power output Power the camera with DC12V 1A power output from the tester It is helpful for demo and testing where there is no power supply available Video Cable SEY tomo E 7 lt 4 Power Cable DC 12V 1A OUTPUT Camera rr V VIDEO IN
16. rnet gt Other Straight through Line Cross Line Open Line or Short Line Ver STP28V 1 1 Page 17 CCTV testerPRO User s Manual 3 7 Data monitor Capture the command data from RS485 controlling system Baud 4800 40 47 00 40 00 00 00 00 00 a Connect the RS485 or RS232 interface of controlling system with the RS485 or RS232 interface of the CCTV testerPRO In case of RS485 A to A B to B La G b Press SET key and then press or LJ key to select communication port according to the system connection Press SET key to save the change A d Press or L system and then press SET key to save the change and capture command data from J key to select the baud rate according to the baud rate of controlling controlling system e Press RETURN key to clear the screen 3 8 Device setting Set the parameters of the CCTV testerPRO Device setting d EEN Keypad tone ON Language English Brightness 7 Not saved Enter to apply Auto poweroff Setting the time of auto shut down Disable 5 10 60 Disable Disable the Auto poweroff function 5 means the CCTV will power off after 5 minutes when there is no any operation Keypad tone Open or close the beep of pressing keypad Language Select language of OSD menu Brightness Setting the brightness of OSD menu and background 0 7 Page g Ver STP28V1 1 CCTV testerPRO User s Manual a Press or b Press 1 or EEZ to change the
17. the battery cables inside the battery cabin should be well connected and the color of cables should be at the same side gt Usually it need not to disconnect the cable at the normal use pressing key continuously can power on or off the tester At the first time of use the batteries should be completely exhausted and then r recharged for 4 or 5 hours yy The Charge Indicator lights red when charging the battery The charge indicator turns off automatically when the charging is completed A Notice When the Charge Indicator turns off the battery is approximately 90 charged The charging time can be extended for about 1 hour and the charging time within 8 hours will not damage the battery A The tester can work as usual while it is being charged however But the charging time will be extended Press the RESET key at the right of the instrument to restore the default settings when the instrument works abnormally Unlock the battery cover by pushing horizontally as the direction illustrated Ver STP28V1 1 Page 9 CCTV testerPRO User s Manual A Warning Connect the terminal of the battery with the direction illustrated Please take care of the polarity of terminal The wires of the same color should be both at the one side N eS a Connect battery leads before use Lock the batteries by pressing as the direction illustrated Page 10 Ver STP28V1 1 CCTV testerPRO User s Manual 3 Operation 3 1 Power
18. value iv key to move the parameter we want to change c Press ENTER to save the change or press RETURN key to give up the change 3 9 PTZ address scanning Search up the ID of PTZ camera Note Please isolate the PTZ camera with other PTZ cameras before searching up Otherwise all the PTZ cameras in the same system will pan at the same time Press keys to Device setting menu Device setting N Prompt sound Language Brightness Address search Not saved Enter to apply ENTER S Press key to confirm after change Address search to on which add address scan sub menu Press to switch the sub menu as illustrated Note The system returns to OFF after shutdown and the Address search Protocol scan sub menu closes automatically Set ON again for next Port Baud use Address Press ser key to set protocol communication port Far Near Start search Wid Tele Adjust addr communication rate make them same as the PTZ camera Press or ar key the address values is constantly on the rise or decrease NEAR The tester will search up the ID quickly and continuously from 1 to 256 When the ID is searched the PTZ camera will pan right At this time please press any key to stop searching up FAR The tester will search up the ID quickly and continuously from 256 to 1 When the ID is searched the PTZ camera will pan left At this time please press any key to stop sea
Download Pdf Manuals
Related Search