User`s manual
Contents
1. Update FW It allows carrying out the firmware update from the programmer Network options 1 Network name 2 o IES ID SN 4 ON LD rE 310 CI System 1 SW version info 2 Date Time 3 Read LOG file 4 Delete LOG file TPE 310 CI Global Update It allows carrying out the update of all the modules that are interconnected at the same time Factory default This option restores the values by default of the transmodulator 16 TFF 310 Cl version_en_2 0 FTE maxima User s manual TFF 310 Cl 3 SD Backup This option allows saving and loading the configuration of the module in the PRO 300 programmer Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below SD BaACkupP Read from module Read from module 1 Read from module CFG 00 2 Write to module Freq 858000 Operation Finish OUTPUT Freq 474000 TEE 310 CI TEE 310 CI TEY 910 CI 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are speci2. Fte maximal TFF 310 CI USER S MANUAL User s manual TFF 310 Cl NOTE This user s guide is adapted to software version v 1 4 70f TFF 310 Cl dated 09 04 2014 For future software updates you can download the users guide from the following website http www ftemaximal com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed its level of operation 3 Never expose the device to leaking nor spattering 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk ln case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device befo
3. 4 Modulator Set Up This option allows configuring the DVB T DVB H modulator of the device Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6MHz and SMHz The BMHz option is only supported by DVB H standard FFT Mode Selection of the number of carriers used in the modulation Options 8K 4K and 2k The 4k option is only supported by DVB H standard Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Modulation Output modulation format 4 4 QAM 16 16 QAM 64 64 QAM Advanced settings Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration 5 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl 5 Set Output channel In this option you can configure the different parameters of the cable signal Channel standard It allows you to select the channelling of the cable signal standards Opti
4. Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 BW Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6 MHz and 5MHz The 5MHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration 10 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Output configuration Out TV In these options you can configure the output parameters of the terrestrial signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options O 15dB
5. and to get into the submenus we have to press OK button 1 Manual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters 1 This field shows the type of parameter that is selected at the moment Options Input Terr Out Terr Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press Cancel NO Terrestrial input Input Ter In this option you will be able to configure the input parameters of the terrestrial signal Freq MHz Input frequency of the multiplex that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 170 230 470 862 MHz BW Bandwidth Selection of the input signal Bandwidth 8MHz 7MHz and 6MHz Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format 4 4 QAM 16 16 QAM 64 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Gl Guard interval
6. receiver in order to be decoded In order to distribute the encoded channels freely you have to install the PCMCIA subscriber card in the Common Interface slot TERRESTRIAL STB i TERRESTRIAL STB Note In order to guarantee the right running of the different equipments of the installation we recommend you to provide the inputs and outputs which are not used with a 75Q load Accesories OUT Programmer l Mod PRO 201 C d 2003123 ind id Mod PRO 300 C d 2003127 STEE Wide band amplifier 47 862MHz T nalani Mod AMP 310 P errestrial antenna C d 2003520 19 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Chapter 2 Technical features TFF 310 Cl Ref 2003552 170 230 470 862 MHz COFDM 38 88 dBuV 750 DVB T 6 7 8 1 4 1 8 1 16 1 32 DVB T 2K 8K QPSK 16 QAM 64 QAM Female F connector lt 1 dB Modulation Error Ratio MER Typ 38 Min 36 Selectable format of output modulation DVB T DVB H Bandwidth MHz DVB T 6 7 8 DVB H 5 6 7 8 Mode DVB T 2k 8k DVB H 2k 4k 8k Output channels C2 C69 Output connectors Female F connector Output Level 80 dBuV Regulation margin 15 dB MIX Losses lt 1 dB Band spurious 60 dBc Programming Interface RJ 45 rar PRO 201 PRO 300 media Max EVO and media 9 Max MINI Yes 2 Slots 0 C 45 C Consumption 12V mA 300 15 Dimensions 75x265x150 mm Weight 1 4Kg Chapter 3 Declaration of conformity
7. Deleting services Decrypt services Decrypt services Decrypt services 1 Add services MS Lot 0 PID 200500 NETOX 2 Delete services Z Slor 2 All ThE SLO CI 1 310 CI ThE S10 CI Mux 0 1 Select the option Delete services 2 Select the slot where the service is 3 Select the service you want to through Up Down buttons Press OK going to be removed through Up delete with the Left Right keys Then to continue Down buttons then press OK press OK over Rem in order to remove it or press OK over All in order to delete all the services of the multiplex Cl menu From this option the access to the CAM menu is allowed select the slot is necessary Reset CAM This option allows the CAM initialization select the slot is necessary 18 TFF310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl 1 5 Accessories and example of installation TERRESTRIAL ANTENNA Weak signal AMP 310 P SPS 310 Filtered and Regenerated signal TFF 310 CI TERRESTRIAL STB TERRESTRIAL STB TERRESTRIAL STB Installation where we get a bad signal and high error rates in the output of the antenna This signal is injected in the headend formed by 6 TFF 310 Cl regenerators which will allow regenerating and or filtering the signal of 6 multiplex so later we can amplify them through and AMP 310 P and distribute them through the installation The distributed channel will need a terrestrial digital
8. Modulation Codificaci n FEC QPSK 16 QAM 64 QAM Note Only applicable for DVB H 1 2 2 3 Guard Interval 1 4 3 110 4 147 1 8 3 456 4 608 1 16 3 659 4 879 1 32 3 770 3 4 5 6 7 8 1 2 2 3 3 4 5 6 7 8 1 2 2 3 3 4 5 6 7 8 4 665 5 184 5 443 6 221 8 294 9 331 10 368 10 886 9 331 12 441 13 996 15 551 16 329 99 5 184 5 760 6 048 6 912 9 216 10 368 11 520 12 096 10 368 13 824 15 551 17 279 18 143 TFF 310 Cl 5 489 6 099 6 404 7 318 9 758 10 978 12 197 12 807 10 978 14 637 16 466 18 296 19 211 version_en_2 0 5 655 19 793 FTE maxima ESPANA Corrals Nous 77 Pol Industrial Can Roqueta 08202 Sabadell Barcelona Espa a Tel 34 93 729 27 00 Fax 34 93 729 30 73 infofOftemaximal com www ftemaximal com DEUTSCHLAND Zweigniederlassung Deutschland Furstenhof 68 59368 Werne Amtsgericht Dortmund HRB 21674 Ust ID Nr DE243384161 Tel 49 2389 92419 0 Fax 49 2389 92419 25 info ftemaximal de www ftemaximal com FRANCE Fte maximal France SAS 7 avenue du Pont de Tasset 74960 MEYTHET Tel 33 4 50 68 80 17 Fax 33 4 50 68 84 68 fte ftemaximal fr www ftemaximal com PORTUGAL Rua Jos Carlos Ary dos Santos A das Lebres Loures 2660 173 Santo Ant o do Tojal Tel 00 351 21 983 87 00 Fax 00 351 21 983 87 09 ftemaximal ftemaximal pt www ftemaximal com Fle maximal ITALIA Via Edison 29
9. included in the output multiplex Adding Removing services Adding Services TEE EE El TRE SO CT BW usage DEER Delete services gt Add services 1 Select the option Add services through Up Down buttons Press OK to continue Deleting Services TEE SALTO CTI BW usage gt Delete services Add services 083 1 Select the option Delete services through Up Down buttons Press OK to continue TEP KE SE LEE DU PTD OSSO mola TV Add 2 Select one of the multiplex services you want to add through Left Right keys and select the Add button to include the service in the multiplex FEE SI CI Sue pu Mo PID 03587 mola TV Rem ALL 2 Select the service you want to delete with the Left Right keys Then press OK over Rem in order to remove it or press OK over All in order to delete all the services of the multiplex 192 TFF 310 Cl Operation finish 3 A window will appear and it will let you know that the operation made has been correct Ee SAT Operation finish 3 A window will appear and it will let you know that the operation made has been correct version_en_2 0 FTE maximal User s manual TFF 310 Cl A Output service name This option allows editing the services name and changing it By means the bottoms Left Right the service to edit is selected pressing OK the edition mode is on placing the cursor over the digit the value c
10. present Once the error or the alert disappears the led will change into orange because the error alert is stored in the registration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green orange red Once you leave the programming mode the led will turn into the corresponding operating mode 9 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Stages of TFF 310 Cl regenerator Input DVB T COFDM Reception of a terrestrial multiplex with a typical error rate in the output of the antenna Service 1 Service 3 FTA Service 4 Service 8 Case 1 Regeneration Case 2 Filtering Regeneration Signal regeneration and possibility of making a services filtering If the multiplex has encoded channels in order to distribute them freely you have to install the PCMCIA subscriber card in the Common Interface slot DVB T COFDM 47 MHz 862 MHz Contiguration of the channel and output parameters of a multiplex with a corrected error rate 1 4 Programming TFF 310 Cl has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector You can make the programming through the PRO 201 PRO 300 programmers and also through the mediaMAX EVO and mediaMAX MINI field strength meter 1 4 1 Programming modes With mediaMAX EVO mediaMAX
11. strength meter TFF 310 Cl has two Common Interface slots TFF 310 Cl 1 Two colored led It indicates the different states of the device 9 Cl Common Interface 5 3 OUT This connector supplies the modulated channel according to the selected standard in the module and mixes it with all the signals that it 6 receives throught the MIX connector 4 MIX Input of mixing of the module 5 ANT IN To connect to the antenna or to the LOOP OUT output of the e 7 previous module 6 LOOP OUT To connect to the ANT IN input of the next module 8 7 RS 232 Ethernet connector to cascade modules with the RCM 310 telecontrol unit with the RJ45 RJ45 cable provided 8 PRO 201 Ethernet connector to make the programming with the programmer 9 DC connectors It has two connectors for connecting between modules 9 3 4 States of two colored leds 1 Initialization mode Green main application charged Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is
12. you wish to include in the output multiplex 3 LCN Once you have tuned a multiplex and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex TFF 310 CI 4 Network options 14 TFF310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Adding Services Output services 1 Add services 2 Delete services BW usage Tre 310 CT Mux 0 1 Select the option Add services through Up Down buttons Press OK to continue Deleting Services Output services 1 Add services 2 Delete services BW usage Tre 310 CT Mux 0 1 Select the option Delete services through Up Down buttons Press OK to continue Output services PID 200500 1 Add ANTENA 3 BW usage Tee 310 CT Mux 0 2 Select one of the multiplex services you want to add through Left Right keys and select the Add button to include the service in the multiplex Output services PID 00500 ANTENA 3 2 ALI BW usage 035 TEE 310 Cl Mux 0 2 Select the service you want to delete with the Left Right keys Then press OK over Rem in order to Output services Operation finish wew 310 CT Mux 0 3 A window will appear and it will let you know that the operation made has been correct Output services Operation fimasia Tee 310 Cl Mux 0 3 A window will appear and it will let you know that the op
13. 42040 Calerno di Sant llario d Enza RE Tel 00 39 05 22 90 97 01 Fax 00 39 05 22 90 97 48 infoOfte it www ftemaximal com UNITED ARAB EMIRATES P O Box 262442 BOUTIQUE VILLA 06 2nd Floor BEHIND KNOWLEDGE VILLAGE MEDIA CITY Dubai UAE Tel 00 971 4 4385509 Fax 00 971 4 4385508 info ftemaximal com www ftemaximal com
14. 745 15 612 16 086 3 4 14 929 16 588 17 564 18 096 5 6 16 588 18 431 19 516 20 107 7 8 1 2 2 3 3 4 5 6 7 8 Useful channel capacity 7 MHz Modulation QPSK 16 QAM 64 QAM FEC codification 1 2 2 3 3 4 5 6 7 8 1 2 2 3 3 4 17 418 14 929 19 906 22 394 24 882 26 126 1 4 4 354 5 806 6 532 7 257 7 62 8 709 11 612 13 063 19 353 16 588 22 118 24 882 27 647 29 029 Guard Interval 1 8 4 838 6 451 7 257 8 064 8 467 9 676 12 902 14 515 20 491 17 564 23 419 26 346 29 273 30 737 1 16 5 123 6 83 7 684 8 538 8 965 10 246 13 661 15 369 1 32 15 834 5 6 14 515 16 127 17 076 17 594 7 8 1 2 2 3 15 24 13 063 17 418 16 934 14 515 19 353 17 93 15 369 20 491 18 473 15 834 3 4 5 6 7 8 Useful channel capacity 6 MHz Modulation QPSK 16 QAM FEC codification 1 2 2 3 3 4 5 6 7 8 1 2 2 3 3 4 5 6 7 8 172 2 3 3 4 19 595 21 772 22 861 21 772 24 191 25 401 Guard Interval 1 8 4 147 5 529 6 291 6 912 7 257 8 294 11 059 12 441 13 824 14 515 12 441 16 588 18 662 23 053 25 614 26 895 1 16 4 391 5 855 6 587 7 318 7 684 8 782 11 709 13 173 14 637 15 369 13 173 17 564 19 76 21 112 23 751 289 27 71 1 32 5 6 7 8 20 735 21 772 21 955 23 053 20 358 22 62 23 751 Useful channel capacity 6 MHz
15. CAM It allows making a reset in the CAM CAM watchdog system In cases where the encoded services stop working you can use one of the following options Disabled No actions will me made in the CAM Retry When it is detected that the decryption of the CAM has been lost the rights will be sent systematically until the decryption gets back Reset As soon as the loss of decryption of the CAM is detected a reset will be made 9 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Both Once the loss of decryption of the CAM is detected the rights will be sent several times until the decryption gets back In cases where it does not get back the module will make a reset of the CAM CAM Reset after It makes a reset of the CAM alter a set period of time Options 0 5 min 10 min 15 min Cl daily reset time Time when the CAM is resetting when this option is enabled PRO 201 Note From PRO 201 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter When you connect the PRO 201 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the regenerator We have to use the Up and Down buttons of the keyboard in order to move to the different options
16. CONFORMITY DECLARATION WE FTE MAXIMAL DECLARE THAT THE PRODUCT TFF 310 CI IS IN CONFORMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company 20 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl ATACHMENT Depending on the configured parameters we are going to obtain one particular channel capacity output useful bit rate In order to make an estimation of this output bits rate we have to take into account the following parameters Symbol duration Ts For signals of 8 MHz Mode 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 896 us 448 us 224 us Guard Interval 1 4 1 8 1 4 1 8 1 4 1 8 1 16 1 32 1 4 1 8 1 16 1 32 For signals of 7 MHz For signals of 6 MHz For signals of 5 MHz Modo 8K 6817 carrier 4K 8409 carrier 2K 1705 carrier Symbol duration 1433 6 us 597 3 us 298 6 us Guard Interval 1 4 1 8 1 16 1 32 1 4 1 8 1 16 1 32 1 4 1 8 1 16 1 32 22 4us 89 6us Modulation Modulation QPSK 16 QAM 64 QAM Number of bits per symbol 4 FFI Mode EAS FFT Mode 2K 6048 3024 1512 6817 3409 1705 Bits rate calculation total Tb orai fs b L Where Fs Symbols frequency symbols sec fs 1 Ts Ts Symbol duration Symbol Time Guard Interval time b Number of bits per symbol depending on the modulation L Number o
17. E maximal User s manual TFF 310 Cl Bandwidth limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will have this state by default Always It selects the services automatically every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode is deactivated the services have to be manually selected Advanced settings Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is recommended to configure a value different from TS ID for each one of the output multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net Tables It allows modifying the value of the following information tables of the DVB NIT SDT PAT Services Change service name lt allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes HDSimulCast In cases where we receive in an installation the same channel in high definition and in standard definit
18. MINI field strength Through PRO 201or PRO 300 the programming is made meter you can carry out the programming of all the module by module modules consecutively as long as they are interconnected with each other through the RJ 45 cable supplied with each unit 3 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl 1 4 2 Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201 and PRO 300 mediaMAX EVO mediaMAX MINI In order to start programming the TFF 310 Cl regenerator you will have to go to Tools option through the key 8 of your field strength meter and to select the Transmodulator Prog option Then it will proceed to recognize the module and to show the main menu In the Transmodulator Prog are shown the different configuration options that this tool offers 1 Select Device The field strength meter allows making the programming of one or several regenerator s and or transmodulator s from only one module Without interconnection of modules Interconnection of several modules you can select which An only module connected module you wish to program 4 TFF 310CIl version_en_2 0 FTE maximal User s manual TFF 310 Cl 2 Device Status In the option Device Status are specified the main parameters of the module at this moment Front End lt indicates whe
19. Summary table Terrestrial input Terrestrial output TV output Frequency Modulation RF Channel Bandwidth BW Invert Spectrum Inversion RF Level Guard Interval Gl Bandwidth BW Tx Mode FFT Mode FEC Mode 2 Auto This option allows saving and loading the configuration of the module in the PRO 201 programmer Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 11 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl 3 Con
20. ded when the value of Noise Margin is lower than the set value NM high limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the regenerator System information It allows you to visualize the basic information of the module model no of series firmware version etc Settings This option allows saving and loading the configuration of the module carrying out firmware update or making an adjustment of the time and date of the module Clock Set Date and time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Alias Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none manual mode 6 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Se
21. djusting the identification parameters of multiplex Network name Associated name to the network TSID Identification value of Transport Stream Give a different value of TSID for each output multiplex configured is recommended NID Identification value of the network ONID Original identification value of the network Tables This option allows modifying the value of the following information DVB service tables NIT SDT PAT 2 System In System option the information concerning the regenerator is given SW version info It allows you to visualize the basic information of the module model firmware version etc Date Time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Read LOG file It allows reading the registered events in the module System Read LOG file N 00000 04 07 14 1 SW version info 2 Date Time 3 Read LOG file 4 Delete LOG file Status o 1018 124090 28 Low FE noise margin Tere 310 CI TEF 310 CI 1 Select the option Read LOG file through Up Down buttons Press OK to continue 2 A new window will appear It will show the information about the registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment
22. ee different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connected an error message will be shown reminding that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory Save programs to USB This option allows copying the programs stored in the external USB 2 0 storage device Write Alias lt allows saving the alias of the module in the program Options Yes No 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex Add Remove services It allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the available space in the output multiplex As you add more services the space available will decrease Once you have tuned a multiplex in the Input Set Up section and you have selected the DVB T DVB H modulator configuration in the Modulator Set Up section you can make the assignment of the services that are go
23. eration made has been correct remove it or press OK over All in order to delete all the services of the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services A Output service name This option allows editing the services name and changing it By means the bottoms Left Right the service to edit is selected pressing OK the edition mode is on placing the cursor over the digit the value could be changed by means the bottoms Up Down One time finished the changes are saved pressing OK LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services 15 TFF310 CI version_en_2 0 FTE maxima User s manual TFF 310 Cl Network Option This option allows a
24. f data carriers depending of FFT mode Bits rate calculation useful T se al T botal Codif rge Codif y ed Salomon FEC Cod FEC Codification 1 2 2 3 3 4 5 6 7 8 Reed Salomon Cod Codification made by the means of Reed Salomon algorithm 188 204 Case study example For example in the case of a DVB T transmission in Spain the configured parameters would be the following 8k mode 2 3 FEC 1 4 guard intervals 64QAM constellation for an 8 MHz channel and using the previous formula you will get the following channel useful capacity TD seni 19 905 Mbps Note As you select a configuration with a higher output channel capacity the protection grade against mistakes gets proportionally decreased Next it is shown the channel capacity for systems without hierarchy in all the cases of constellation guard interval and codification relation for transmissions of 8MHz 7MHz 6MHz y 5MHz DVB H The useful capacity channel is identical for modes 2k 4k DVB H and 8k 91 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 CI Useful channel capacity 8 MHz Modulation FEC codification 1 2 4 976 Guard Interval 5 529 5 855 1 32 6 032 2 3 6 635 7 373 7 806 8 043 3 4 5 6 7 465 8 294 8 294 9 216 8 782 9 758 9 048 10 053 7 8 8 709 9 676 10 246 10 556 1 2 9 953 11 059 11 709 12 064 2 3 13 271 14
25. fied below SD Backup Write to module Write to module 1 Read from module EEG 00 2 Write to module Freq 858000 Operation finish EIS pur Freq 474000 a 310 CI DEE 310 CI TEE S10 CI 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 4 CAM This option allows selecting which services are decrypted and enabling the access to the CAM parameters CAM 1 Decrypt services 256i menu 3 Reset CAM TFE 310 CI Decrypt services From this option you can add or remove manually the services that are being decoded by the card ES TFF310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Addingservices Decrypt services Decrypt services Decrypt services PID 00500 NEOX i Slee 2 Delete services 1 Add oS lence 1 EES TFE 3L0 CT Tee 310 CI Mux 0 EE 310 CI 1 Select the option Add services 2 Select one of the multiplex services 3 Select the slot where the service is through Up Down buttons Press OK you want to add through Left Right going to be decrypted through Up to continue keys and select the Add button to Down buttons then press OK include the service in the multiplex
26. fig In Config option the information concerning the regenerator is given ERR 310 Cl Global Update gt Read LOG file Delete LOG tile Read log It allows reading the registered events in the module TEE Si T N 200001 Starus 00 107 07 14 Oas TSAN System Ok TRE SCT TER SIT ET Global Update OK to Show LOG gt Read LOG file Pelete LOG file 1 Select the option Read LOG file through Up Down buttons Press OK to continue 3 A new window will appear It will show the information about the registered events in the module Press the following keys in order to scroll up and down the screen up down 2 Press OK again to show the log file Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the transmodulator Update FW It allows carrying out the firmware update from the programmer Net name Name associated to the net TSID Identification value of Transport Stream Give a different value of TSID for each output multiplex configured is recommended NID Net identification value ONID Original Net identification value Output services This option allows making the selection of the services that you wish to include in the output multiplex Once you have tuned a multiplex and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be
27. ing to be included in the output multiplex Adding Removing services J TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Adding services 1 Select Service to add option 2 Select one of the multiplex 3 Once you have chosen the services you want to add service select the Add Rem button to include the service in the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Excessive capacity It is recommended to remove services Recomendad capacity lower to 85 Removing services 1 Select the Service to remove 2 Select one of the multiplex 3 Once you have chosen the option services you want to remove service select the Add Rem button to remove the service in the multiplex Remove all services It allows removing all the services included in the multiplex Modify LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services 8 TFF 310 Cl version_en_2 0 FT
28. ion the HD Simulcast function allows to exchange the position of the LCN of both channels If the user has a device compatible to HD Simulcast and the module has been correctly configured when tuning the standard definition channel it will move to its position in high definition automatically This option allows modifying manually the position of the LCN exchanging the standard position into the high definition position In the first line you have to select the high definition service and in the second line you have to select the same service but in standard definition Change in Service ID From this position you can change the PID Number of the chosen service Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Hotbird 13 E Eutelsat 13 E Astra 19 2 E Astra 28 2 E 2 2 Astra Satellite Network 28 2 E Nilesat 7 W 2048 2048 Nilesat 101 Hispasat 30 W 33 33 Hispasat Network 1 9 Common Interface This option allows checking the information and configuring the parameters regarding the conditional access CI Menu From here you can reach the menu of the card inserted in the CAM Decryption From this option you can add or remove manually the services that are being decoded by the card Remove all decrypted services From this option you can remove all the services that are decoding the conditional access card Reset
29. nd Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update of all the modules that are interconnected at the same time Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices It allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allows making values by default to all the interconnected modules T Program management New program This option allows creating a program with the current configuration of a module or group of modules Load program It allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules Working disk With this option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among thr
30. ons BG BG PAL BG IT LL M NTSC PAL M PAL N PAL DK PAL I BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated signal Options O 15dB Calibration Allows the realization of two tests in order to verify the correct running of the device Deactivate output It allows activating or deactivating the output of regenerator Switch output to CW It allows activating or deactivating the DVB T DVB H modulation allowing visualizing the carrier without modulation in the selected frequency 6 System This option provides information of the regenerator System logfile In this field are indicated the registered events in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device NM low Limit dB An event of error will be recor
31. or example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H EE 310 CI codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration Output configuration Out TV In these options you can configure the output parameters of the terrestrial out py signal 1 RF Channel RF Channel MHz Output frequency of terrestrial modulation In order to 2 RF Level introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value TFF 310 CT Options 47 862 Mhz RF Level Regulation of the output level of the modulated signal Options O 15dB Summary table Terrestrial input Terrestrial output TV output Frequency Modulation RF Channel Bandwidth BW Invert Spectrum Inversion RF Level Guard Interval GI Bandwidth BW Tx Mode FFT Mode FEC Mode Services configuration This option allows configuring the features of the output services Services config Output services This option allows making the selection of the services that 5 Output serv Name
32. ould be changed by means the bottoms Up Down Once finish the changes are saved pressing OK LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes A Decrypt services From this option you can add or remove manually the services that are being decoded by the card Delete services Add services Reset CAM This option allows the CAM initialization select the slot is necessary CI menu From this option the access to the CAM menu is allowed select the slot is necessary Date Time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firmware version etc Global Update It allows carrying out the update of all the modules that are interconnected at the same time Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to
33. re handling the connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content be S lt S Pl d 2 x Bridge F male F male DC Cable TFF 310 Cable 12 cm PIN to PIN RJ45 RJ45 Stopper sch WE TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl 1 3 Description and connections The module TFF 310 Cl is used for the reception of free channels that obey the DVB T standards Each module allows the reception of a complete multiplex in DVB T COFDM and its subsequent regeneration in a new multiplex Besides it offers the possibility of selecting the services that you wish to add in the new multiplex A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any interference problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of PRO 201 PRO 300 or the EVO or MINI series of field strength meter and they are monitored in the display of programmer or on the screen of field
34. the possible variability of the bits rate of the inputs services Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services PRO 300 A When you connect the PRO 300 programmer it will proceed to recognize Note From PRO 300 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter Main menu the module and to show the main menu In the main menu are shown the different options for configuring the regenerator We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button 1 I O configuration Inside the I O configuration menu there are specified the different options for setting up the input output and modulation parameters In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press Cancel Terrestrial input Input Ter In this option you will be able to configure the input parameters of the terrestrial signal Freq MHz Input frequency of the mul
35. ther the module is hooked or without signal Input bit rate Transfers of data in the terrestrial tuner input Output bit rate Transfer of data in the module output BER before and after Viterbi It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm MER Parameter that indicates the quality of the input modulated digital signal expressed in dB Noise Margin It indicates the difference between the value of current C N and the value of C N at the point of pixilation of the signal that is the quantity of dBs of C N measure that are needed to lose the input signal Temperature lt indicates the current temperature of the module in degrees 3 Set Front End In this option you will be able to configure the input parameters of the terrestrial signal Channel Input channel of the multiplex that you wish to tune When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C5 C12 021 C69 Frequency MHz Input frequency of the multiplex that you wish to tune When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 170 230 470 862 MHz Bandwidth Selection of the input signal Bandwidth 8MHz 7MHz and 6MHz
36. tiplex that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 170 230 470 862 MHz 1 I O configuration 2 System 3 SD Backup 4 CAM TEE 310 CI Y O eee O L Input Ter 2 Out Ter 3 Our TY A Services contig TPE 310 CI Opel 570000 8 MHz 1 Freq 2 Bandwith Tee 310 CI BW Bandwidth Selection of the input signal Bandwidth 8MHz 7MHz and 6MHz 13 TFF 310 Cl version_en_2 0 FTE maximal User s manual TFF 310 Cl Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Out tex Modulation Output modulation format 4 QAM 16 QAM 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in 1 Modulation the modulation 2 Invert Gl Guard interval Allows selecting the guard interval of the modulation 3 GI 1 4 1 8 1 16 and 1 32 4 Bandwith BW Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6MHz and SMHz The SMHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 F
Download Pdf Manuals
Related Search