WaterLevV™ - American Best Pool Supply
Contents
1. 3 PVC T Fitting Garden Hose Adapter User s Manual and Installation Manual Remove contents from shipping packaging and verify contents are complete Before starting the installation verify that the pool is filled to the desired level Please see Figure A for typical system configuration Valve Unit Sensor Skimmer H a oe ee Return to Pool GT Figure A Hl Unit Specifications sensor Unit Power operation Operating Cycle Operating Range Model IGW 5000 Range Installation Warranty Valve control Unit Power Supply Rain tight outdoor type rating Operating Cycle Output Volume Operating Temperature Inlet Fitting Type Outlet Fitting Type Water pressure System Alarms Warranty Maintenance 9 VDC Valve supply voltage Level Check every 1 hour 40 F to 125 F 5 C to 55 C 75 ft 23 meters of cable Adjustable height 1 Year 120VAC 138mA 9VDC 1A 5 minute Valve on Time Approx 32 Gallons 120 Litres 40 F to 125 F 5 C to 55 C 3 4 Male Garden Hose Fitting Male 3 4 NPT 15 100 PSI Low Battery High Water No Flow Possible Leak 1 Year If the system no longer maintains the water level please check the following 1 Water Inlet screen may be blocked with dirt or debris Shut off the water source and remove Inlet connection then remove the 3 3 adapter The Dirt screen is located in the2. Inlet port remove clean and replace Reconnect the water connection and turn on the water source If Dirt Screen is not replaced damage to the valve may occur 2 Lose of Power e Verify that the Power Adapter is plugged and functioning e Power LED of the Valve Unit should be On Control Unit LED definition as follows LED No 1 Indicates Power On Status LED No 2 Indicates Data Received LED No 3 Indicates Valve activation LED No 4 Indicates Low Battery Alarm n a on the IGW 5000 LED No 5 Indicates High Level Alarm 4 Beeps every 6 minutes LED No 6 Indicates Water Flow Error Warble Tone every 7 minutes Control Valve Reset Switch definition Press Reset Button for 1 second to silence Alarms Hold Reset Button for 3 seconds to Reset Alarms Hold Reset Button for 3 seconds to Reset Water Valve System Seasonal Power down procedure Disconnect the Valve Units power source or Power Supply cable If you live in an area where Freezing is possible Disconnect Drain and or shut off the water source Sensor Installation Choose a location to install Sensor Bracket some possible locations are in the neck of the skimmer behind the skimmer weir or on any surface touching the water Keep in mind to keep the Sensor away from being hit or damaged from Childs play or other objects You can attach the Sensor Bracket with ABS Pipe Glue or with Stainless Steel screws supplied Install the Sensor in the Bracket and adjus
3. Notes W Fe Lig TED This product has been tested to the requirements of CAN CSA C22 2 No 61010 1 second edition including amendment 1 or a later version of the same standard incorporating the same level of testing requirements This product must be installed under the guidelines of the National Electric Code or the Canadian Electric code Note If used in a manner not specified by the manufacture the protection provided by the equipment may be impaired Distributed by ENERGY FOCUS INC 32000 Aurora Road Solon OH 44139 1 800 327 7877 Manufactured by WaterLevvV Inc Montreal Canada Rev 4 08042009 i b gt lt oe _ mt amp a eal eS o a E s a E u See oer ge m A AN ENERGY Focus COMPANY j www energyfocusinc com WaterLevV Installation Manual Model IGW 5000 Cabled Model Pool and Spa Water Level Monitoring System Thank you for purchasing the Industries newest and most technologically advanced Pool Spa water level monitoring system on the market Your new Pool Spa Water Level System is fully automatic The system incorporates several user alarms which indicate both Water Level or flow issues and System monitoring such as Low Battery monitoring and loss of water flow Please Read before Installation Systems Contents Sensor with 75ft cable Sensor Mounting Bracket Skimmer Lid Bracket Valve Control Unit with built in Check Valve 2 x 2 x
4. ally verify the Pool or Spa s water level every hour The system will automatically add water in 5 minute intervals whenever a low level is detected High Water Level monitoring If an extended High Water Level more than 12 hours is detected the system will alert you a Back Wash or drain may be required to lower the water level If the High Level is minor standard water dissipation over the following days will automatically reset High Level Alarm and the system will returns to normal status Low Battery Level detection not available on the IGW 5000 Water Flow monitoring The system automatically monitors Water flow If an extended loss of water flow is detected a Flow Alarm will be triggered This alarm also can detect a leak in the Pool an excessive number of low Level demands may indicate a leak Sensor LED definitions as follows YELLOW indicates LOW LEVEL Detection RED indicates HIGH LEVEL Detection GREEN indicates Send Data Figure J Apply Water source to verify there are no leeks Return Filter Control to normal position and turn on the Pool Pump Installation is now complete System Start up sensor Unit has a built in Start up mode which gives the Installer time 10 min to adjust the Sensor Level and visually see LED s display the Water Level Status If additional testing time is required simply remove and replace the Sensor back in its Bracket this will restart the start up
5. ed use standard GHT fitting to complete Inlet connection Figure
6. period Shut off the power to the Pool Pump and switch the Filter control to Drain or Back Wash Locate the return line from the Pool pump to the Pool Choose a location on the return line to cut and install T fitting See Figure F From Pump Return to Pool From Pump Glue T fitting with the 3 4 Fitting pointing vertically upwards Let glue set for one to two minutes See Figure Q Figure F Figure G Next apply 2 3 turns of plumber tape to the outlet of the Valve unit Thread Valve Unit into the 3 4 T fitting Tighten Valve by hand do not use Pliers or grips Power Source and Sensor Connections Remove the Blue Valve Cover then remove the Cable Clip by loosening the Phillips screw located on the outside of the Valve Unit Remove the Clip and install the Power Supply Cable and Sensor Cable Insert Connectors with Cable pointing upwards and then loop the cable downwards See Figure H Replace Cable Clip and tighten Philips Screw to lock the Power Cable in place Figure H Water Source Connection Install Garden Hose adapter to Valve Unit Inlet Attach the short side of the Fitting to the Valve and the longer side is to attach to your Water Source This connection is necessary to leave access the Water inlet Screen Filter for future cleaning See Figure Il amp J If a permanent Water source is preferr
7. t Sensor approximately 1 4 above Water level A Skimmer Lid Bracket is also supplied in the case that the Sensor is to be placed attached to the Skimmer Lid Here Figure B Skimmer Lid Bracket Figure C Skimmer Bracket can be installed with ABS compatible adhesives such as ABS Pipe Cement or Attach with Screws Sensor Cable Installation Once the location of the Sensor has been determined you will need to drill a hole as near the top edge of skimmer close above the Sensor Pass the Sensor wire through the Hole See Figure D a Place Sensor Here Figure D Install a Y PVC Electrical conduit between Skimmer and Valve Unit Location See Figure E i i i i ae a Fi F fi i J Fi ee f fi a P a _ T vl Figure E With the help of a cable fish gently pull the Sensor Cable through the conduit Seal the Cable Hole in the Skimmer with Silicon System Functions Sensor is in a Start up test mode for the first 10 minutes after Sensor is installed in the Sensor Bracket this will allow you to test the level by moving the Sensor unit up or down on the bracket to test Valve activation If further testing is required simply remove sensor and re insert back into the bracket this will restart the test mode See Sensor LED definitions on the Last Page Low Water Level monitoring The WaterLevV System will automatic
Download Pdf Manuals
Related Search