User Manual
Contents
1. 34003113u1uk one gt remote OneRemote converter Type 34003113 User Manual Operate with Beolink Panasonic DVDR HDD recorders with HDMI output Everyday use OK a 1 Drive select D 1 Return a CH 41 CH Hm Direct Navigator Hea Guide So Hm List MENU Functions 1 As the un shifted function of the coloured function buttons has been assigned to other functions they have to be preceded with a toretrieve their actual coloured functions Go a Green function Yellow function Go A Red function v Blue function Operating using a Beolink 1000 or other old remote controllers Older remote controls do not have coloured buttons and use is not logical As Beolink 1000 has no coloured buttons the Zapmode option needs to be set to make the the up down arrows serve as P and P See page 6 about option programming The button on older Bang amp Olufsen remote controls does the exact same operation as the button on never remote controls one gt remote Playback amp Recording Go EH D GO A um Hm li Play pause press 1 sec Play pause Stop Rew FF Previous next Timeslip Record Prog Check Other operations 806080 UT Display Functions alternativ Audio Power manuel Return Drive select Return Exit Green function Yellow function NA Ea PN Blue function NA Ei BA Red function one gt remote Congratulations The EX2. T controller from www oneremote dk can fully operate your Panasonic DVDR HDD receorder using your Bang amp Olufsen remote control terminal via a Bang amp Olufsen TV Beo4 BeoS or Beo6 remote controls can be used Beolink 1000 can be used with reduced functionality This guide explains how This EXT RCA controller is ready for use plug amp play See the opposite page regarding daily operation Some operations can be altered to improve interaction with other controllers or to your convenience Refer to the installation section further on if changes are needed one gt remote EXT RCA controller When a scart type connected source is selected with a Bang amp Olufsen remote control the B amp O TV starts to parse control data from the remote control to the attached device via the scart cable The OneRemote EXT RCA controller captures these data and converts these into IR data that can operate the specific device The converted IR data is being transmitted via a small R emitter that has to placed in front of the device to be controlled Here it emits the same IR data into the front of the device that it was made to receive from its own remote control Example of IR emitter placement As an EXT RCA controller operates on data received via the scart connection it will function only when attached to a B amp O TV If both the B amp O TV and the device are equipped with DVI and or HDMI sockets a suitable cable can b
3. e added to improve the picture quality The EXT cable will still be needed for control data and maybe also the sound Refer to the user manuals for both the TV and the device about correct installation of HDMI DVI cables In a setup with link rooms all rooms will be able to operate the device via the link system With a OneRemote OneWay or TwoWay cable the device can be placed up to 25 metres away from the TV It could be placed in another room under a sofa or where ever it suits as operation is handled via the Scartcable If both the TV and the device are equipped with a HDMI connection a HDMI cable can be added to improve picture and sound quality one gt remote OneRemote operation in a B amp O system To be able to operate the device correctly with a B amp O remote control the user has to be familiar with operations with the original remote control as described in the device s user manual B amp O remote controls are not equipped with many keys so we have designed a layout that works logically even when shifting between different devices To get a common layout for many devices we therefore needed to redefine a few of the beo4 buttons to other functions Coloured buttons To make room for direct access to important functions we have moved the coloured buttons to a lower layer To send a red button command must be pressed before the red button willsend the actual red command The same goes with the
4. me that does not occur during daily use A programming must be ended within 10 seconds To abort an ongoing programming sequence press any other button than or the numeric buttons HQ to ME Power off option In some cases it is not wanted that the device automatically powers off when the TV is powered off Use this option to enable or disable this SO GEC GC EOJ ECJ ECA A Device never powers off Sr EC GTC ECI ECJ GCA EEA EEE Device powers off with TV Menu option Some B amp O TVs not only echoes the MENU button from the remote control to the device attached to the Scart socket It also opens the TV s own ON screen menu Use this option to avoid that the device acts on this command if your setup has this conflict Sr ELI Er Er ECJ GCI ES Use the MENU button Sr ELI ECI Er ECJ EGC ES ignore the Menu button one gt remote Installation troubleshooting The OneRemote EXT RCA cable must be connected to a scart input socket on the TV Then the R emitter must be stuck in a way that it can emit IR light in to the devices IR receiver that normally receives the IR light emitted from the devices own remote control Only scart input sockets can be used that are able to send out linkdata to the EXT RCA controller Also the TV must be programmed to send out data to the scart socket which is done in the TV s Sources menu Refer to the TV s user manual The EXT RCA controller emulates DVD VMEM VTAPE SAT DTV VAUX and o
5. other 3 coloured buttons This way we are able to assign other functions to the coloured buttons when they are pressed directly In a OneRemote environment the coloured buttons is mostly assigned to these operations Ga Guide EPG or similar DD Back Backup Return or similar y D Programme zapping P P Channel up down or CH CH Programme stepping up down manoeuvring in menus Most set top boxes or TV s has 4 arrow buttons for moving up down left and right in on screen menus In addition they have separate programme stepping buttons for zapping through programmes B amp O remote control does not have separate buttons for programme zapping We therefore have chosen the blue and the yellow buttons to function as programme stepping buttons The four up down left and right buttons have been assigned for manoeuvring in on screen menus in our basic setup It is possible to use the up and down arrow for programme stepping refer to the installation section Go Record and Stop shifted operation Some of the buttons has two or three functions To get to these they have to be preceded with or The buttons that has been assigned secondary functions on this controller can be seen in the operating table on page 2 one gt remote Option programming The OneRemote EXT controller can be programmed with different options to fit different set ups An option programming is done by pressing a series of buttons in a special sche
6. ther sources There is no programming needed on the EXT controller The EXT RCA cable is equipped with a control LED build in to the scartplug that is inserted in to the device This LED assists in faultfinding if something is not operating correctly The EXT RCA converter measure if there is a video signal present via the yellow RCA plug This plug therefore needs to be inserted to the yellow Video out on the player The red and white RCA plug must be connected to the audio out sockets of the player if the TV is not connected with a HDMI cable Control LED indications Continous red or green flashing When power is applied to the EXT controller the LED will start flashing The flash indicates that the EXT controller has not received a command data from the TV since power on As soon as a command is received from the TV the LED will stop flashing and light solid red or green If the control LED continues flashing after you have selected the source on the TV where the cable is attached the socket does not include control data or the TV has not been set up correctly Refer to the TV s user manual LED colour The EXT controller will light red when it has detected a device that is powered on It will either flash or light solid red The EXT controller will light green when it is not connected to a device or if it is connected to a device that is powered off If not connected to the TV output socket of a device the EXT controller
7. will not be able to measure if the device is powered on and therefore always light green LED short flash off During use the LED will light red or green depending on the powerstatus of the device When receiving a controldata from the TV the control LED will shortly go out to indicate this If a button is pressed on the TV s remotecontrol supposed to operate the device and teh LED does not indicate this the TV has not been correctly set up
Download Pdf Manuals
Related Search