FRE-301R quick start main copy
Contents
1. then automatically restart self levelled Setting Y axis slope This sets a grade in the Y axis Procedure switch ON the FRE 301R then auto levels Press the Manual button on laser s keypad bottom left hand side amp the green LED illuminates Using the up amp down Arrow buttons set the slope fall required as measured on your staff The same buttons can be found on the Remote Control cont To return to Auto level switch the Manual button to OFF green LED turns off The Laser will wait to find true level then automatically restart self levelled Setting both X amp Y axis slope dual grade Proceed as above but use all four arrow buttons as required Automatic Drift System ADS Operated via bottom right hand yellow button showing a picture of a tilted instrument Once the FRE 301R is ON and rotating in the auto self levelled mode the automatic drift system can be activated Press the button amp the green LED will flash continually ADS is now ON If the Laser is knocked or caught by a gust of wind for example the laser head will stop rotating and the green ADS LED will flash quickly in alarm condition Check all is OK press the ADS button again amp the laser will reset to AUTO level IMPORTANT NOTE The ADS function cannot be set when Grading Remote Control amp Laser Detector Remote Control is pictured on the left Remote Control Fit the supplied 2pc x AA alkaline ba2. Quick Start FRE 301R INSTRUCTIONS Instrument colours may vary from P R Engineering Ltd www laser level co uk Tel 01246 269777 Thank you for purchasing the Fukuda FRE 301R RED beam rotary laser kit These instructions are intended to explain the quick basics to operating this equipment Please read them in conjunction with the Manufacturer s User Manual included in the kit If you need any more help advice or the instrument requires calibration or repair then please contact our Service Dept on tel 01246 269 777 or fax 01246 260 007 We would be pleased to help Power source This is a special battery pack located in the base of the laser Remove amp refit via a central screw finger tight no tools are required It contains 4pc x sealed for life Ni MH type C 4000mAh 1 2V cells Please note that this battery pack can be charged either in or outside of the laser The Mains Charger supplied will charge most batteries in around 7 hours to give around 40 hrs of continuous use It takes 4 to 5 charge discharge cycles for these battery packs to reach their maximum capacity Mains Charger The general procedure to adopt is use the laser during the day amp charge up overnight You cannot damage the system by over charging the batteries When plugged into a 230V mains supply the red LED flashes every 1 sec Connect to the rubber protected socket located in the corner base of the battery pack amp this LED should be ON conti
3. en used with the supplied Laser Detector Even with its bright Red beam a detector will still be required for most outdoor work SCAN function for Interior setting out The top button on the right of the keypad is the Scan function The User can set a Dot or 10 45 90 180 degree lines as required amp use the two buttons top left hand side of the keypad to move these lines around the room AS THIS LASER AUTO LEVELS BOTH HORIZONTALLY amp VERTICALLY all the control settings above operate in either mode Grading This is a DUAL GRADE facility laser level This means that the FRE 301R can be switched to Manual to over ride the level sensors and then the User can set a grade incline slope in the X axis only Y axis only or both together The max settable slope is an approx fall of 1m over 10m For X amp Y alignment please see the case markings on the TOP of the laser body where an arrow points in the direction of the axis being set Setting a single axis slope This sets a grade in the X axis Procedure switch ON the FRE 301R then auto levels Press the Manual button on laser s keypad bottom left hand side amp the green LED illuminates Using the left amp right Arrow buttons set the slope fall required as measured on your staff The same buttons can be found on the Remote Control To return to Auto level switch the Manual button to OFF green LED turns off The Laser will wait to find true level
4. k area General Advice This is an accurate measuring device so to give good service look after it Prevent the FRE 301R from receiving severe knocks bangs or vibration Store the laser amp its accessories in the supplied carry case If wet dry before storing amp keep in storage temperatures between 5 30 deg Gs Remove all batteries before long term storage to prevent internal damage Key Specifications Laser accuracy 3mm 30m Operating range 20m visible or 300m diameter with detector IR Remote control range 20m for full details see main Manufacturer s User Manual There are NO User Serviceable Parts This would void the warranty We offer a full Back up service including repairs calibration amp usage advice Accessories for the various Trades are also available on request eg Tripods staffs screeding poles amp wall brackets etc Please contact us P R Engineering Ltd Unit 35 Bridge Business Centre Beresford Way CHESTERFIELD S41 9FG England Tel 01246 269777 Fax 01246 260007 sales laser level co uk www laser level co uk kkkkkkkkkkkkkkkkk
5. nuously ie Red LED charging Green LED sufficient charge to operate Even though the Green light is ON we still recommend a full 8 hour charge The FRE 301R can be operated with the charger connected to the mains supply if required On receipt of your new laser we suggest charging the batteries fully overnight A Spare Battery holder is an optional extra amp used as a back up power source Four type C 1 5V Alkaline batteries can be used instead or in an emergency but do NOT attempt to recharge them otherwise serious damage will occur Positioning the Laser Mount the FRE 301R on a generally level firm surface or 5 8 threaded Tripod To operate correctly this surface must be within 5 deg of true horizontal The laser can be used Indoors or Outdoors where it is waterproof to IP54 Controls Power ON OFF is via the black button The laser takes approx 15 to 25 seconds to auto level amp then the head rotates amp projects a visible red laser beam The rotational speed is variable in 4 increments Adjust head speed using the yellow speed control button right hand side in centre amp when pressed it stops the red dot then increases the head s rotational speed in 4 steps up to a maximum speed of 600rpm For Interior work we suggest using slower speeds where the laser beam is easier to see by eye but for Exterior Groundworks run the FRE 301R its maximum speed of 600rpm which gives the best working range wh
6. tteries taking care with correct polarity The Remote s keypad can set the following functions 1 Rotating speed in increments slow for Indoors fast max for Outdoors 2 Scan angles in increments 3 Scan line position around the room 4 Auto Manual grade settings via top middle button 5 Four ARROW buttons to set required X Y grades TIP it is often better to use the Remote Control rather than the instrument s keypad because then you do not disturb the laser s sensitive mechanism Detector Fit the supplied 9V battery polarity marked Power up via ON OFF button The top button switches the sounder volume ON or OFF if required The middle button sets coarse 2mm or fine 1mm red pick up window resolution A rear LCD repeats the main front display Note the case markings amp setting notches You can use the detector with or without its staff mounting bracket Detector Procedure face towards rotating laser amp find rotating laser beam via the red pick up window If the sun is low in the sky amp shining into the red window shield it with a cupped hand to prevent false readings Positioning the FRE 301R itself in full sun is no problem but the detector window can in some instances be affected by direct bright sunlight or reflections So please take extra care SAFETY PRECAUTIONS Comply with class 2 laser operating safety procedures See main Manual Display a Laser Safety Notice in the wor
Download Pdf Manuals
Related Search