User Manual - SmallAppliance.com
Contents
1. www krups com LP 2 gt el Sa IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following Read all instructions carefully eDo not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid eClose supervision is necessary when any appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to your nearest authorized KRUPS Ser vice Center for examination repair or adjustment see Guarantee of Performance eThe use of an accessory not evaluated for use with this appliance may cause injuries Do not use outdoors eDo not let cord hang over edge of table or counter or touch hot surfaces Do not place on or near a hot gas or electric burner or in a heated oven To disconnect turn switch to OFF then re2. Ground coffee not compacted enough Compact the ground coffee more Ground coffee old or too dry Use a fresh ground coffee The milk is not Nozzle blocked See paragraph leaks around the filter holder very foamy Maintenance Milk too old Use fresh milk Milk is lukewarm Put the milk in the refrigerator When using Measure badly Position it E S E coffee positioned correctly See paragraph Preparing an espresso with an ESE measure Filter holder not Tighten it until it in the ground coffee not compacted tightened locks click properly Lots of water Ground coffee Compact the ground coffee Insufficient quan tityof ground Increase the quantity of coffee ground coffee There is water The drip tray Empty itregularly around the is overflowing appliance Accessories You can obtain the following accessories from your retailer or from an approved KRUPS service center Filtration cartridge ref 088 Descaling kit ref 054 16 Krups Limited One Year Warranty Your KRUPS F927 is covered by the following warranty If within one year from date of purchase this KRUPS product fails to function because of defects in materials or workmanship KRUPS North America will at its option repair or replace the unit without charge provided the owner has a proof of date of purchase This warranty will be voi
3. Very loud noise from the pump No water in the ank Fill the tank 00 old or very dry Tank badly Press firmly on itted the tank Ground coffee Use freshly ground coffee Corrective actions Problems Likely causes Water does not run through No water in the ank Fill the tank Tank badly itted Press firmly on the tank The filter holder is blocked the ground coffee is 00 fine or too Clean the filter holder and the grille of the percolation head compacted See the para graph Mainte nance and try using a Coarser ground or less compacted coffee Grille of the Put the grille to percolation head soak in the is encrusted descaling solution See the paragraph Descaling Appliance needs See the descaling paragraph indicator light Descaling e1 is lit Espresso not hot enough The accessories are cold cups and filter holder Pre heat the accessories See the para graph Espresso function Water passes too too quickly Ground coffee coarse Try a finer ground coffee Insufficient quan tity of ground coffee Use the spoon supplied to measure out the coffee krups 15 Ground coffee not compacted Compact the ground coffee more The espresso has no head foam on the coffee Ground coffee too coarse Try using a finer ground coffee
4. suitable for your appliance e Do not use the appliance unless the drip tray and the grille are in place e Make sure the filter holder is correctly positioned before starting to make and do not remove the filter holder containing the ground coffee while water is passing through as the appliance is under pressure at that time e All KRUPS appliances are subjected to very strict quality controls Practical tests are done with some appliances selected at random which explains any signs of use Before first use 1 Fitting the filtration cartridge n e Assemble the 2 parts of the key n1 Unpack the cartridge and attach it to the key e Position the cartridge in the tank and screw in 1 then remove the key The cartridge change indicator c lets you know when to change the filtration cartridge place the left part of the notch over the figure indicating the month of first use the right part of the notch shows you the month to change the cartridge E g if the left part is on 1 January you must change it in 3 March Note e After each cartridge change perform a full rinse of the machine with half a tank of water see paragraph Rinsing the water system 2 Adjusting the limescale monitoring system Your appliance is equipped with a limescale monitoring system which lets you know when to perform descaling the indicator light marked fl e1 comes on To find out
5. Check that the voltage rating of your appliance does in fact match that of your electrical system e Only connect the appliance to an earthed socket Any connection error will render the guarantee null and void e Your appliance is intended solely for domestic and indoor use e Unplug your appliance as soon as you have finished using it and when you are cleaning it e Never use your appliance if it is not working correctly or if it has been damaged If this happens contact an approved KRUPS service center see list in the service booklet e Any intervention apart from normal cleaning and maintenance by the customer must be carried out by an approved KRUPS service center e Never place the appliance the power cord or the plug in water or in any other liquid e Do not allow the power cord to hang down within the reach of children e The power cord must never be close to or in contact with the hot parts of your appliance close to a source of heat or resting on a sharp edge e Never unplug the appliance by pulling on the cord e If the power cord or the plug are damaged do not use the appliance In order to avoid any risk these must be replaced by an approved KRUPS service center see list in the service booklet e Do not place the appliance on a hot surface such as a hotplate and do not use it close to an open flame e For your own safety you should use only the KRUPS accessories and spare parts which are
6. that you descale your espresso in order to guarantee its continued operation You must descale your appliance when the indicator light HH e1 is lit see Before first use section e Descale your espresso at regular intervals using citric or tartaric acid We do however advise you to use the Krups descaling accessory reference 054 which 14 Krups is available from approved Krups service centers You must never under any circumstances use classic sulphamic acid or other products containing this acid as there is a risk of damaging the appliance Carefully check the composition of the descaling products you intend to use Then use the following method e Remove the filtration cartridge n by unscrewing it using the key n1 e Unscrew the grille of the percolation head and clean it 13 e Dissolve 2 tablespoons of descaling product or half a sachet of accessory 054 in half a litre of lukewarm water and pour it all into the empty water tank e Press the on off control e2 and its indicator light will flash e Turn the tap 11 to the dy position e Place a container under the nozzle i2 8 If necessary adjust the height of the grille support 4 The tip must not touch the bottom of the container so as not to obstruct the passage of the water As soon as the appliance reaches the right temperature the indicator light of the control e2 stops flashing e Press the L c
7. ation as many times as necessary to empty half the tank e Empty the container regularly and repeat the operation e Then move the container under the nozzle 12 and turn the tap 11 to the dy position elf necessary wait for the indicator light of the on off control D e2 to become steady and press the M control e5 e Turn the function selector d to the J position and allow the water contained in the tank to run through The tip of the nozzle i2 must not touch the bottom of the container e Once the container is full turn the function selector d to the W position e Empty the container then resume the operation until the tank has been completely emptied e At the end of the operation turn the function selector d to the W position press the ML control e5 and press the on off control D e2 to turn off the appliance 10 Krups Using the various functions of your espresso Important Appliance ready When using the various functions after pressing the control e2 the indicator lights of the other controls may be either on or off This has nothing to do with the progress of the operation The important thing is to wait for the indicator light of the on off control O e2 to stop flashing Interrupting operations in progress when the water tank b is empty The appliance stops and all the indicator lights flash for about 5 seconds w
8. ction in memory and to complete he adjustment procedure Note If you do nothing for 10 seconds the adjustment procedure stops automatically and the changes are not recorded 3 Rinsing the water system Rinse the water system with one or two tanks of water as follows e Remove the lid a take out the tank b and fill it with water 2 e Replace the tank positioning it firmly so as to open the connecting valve situated below the tank and replace the lid e Plug in the appliance KRUPS e Press the on off switch D e2 and its indicator light will flash e Fit the filter holder without coffee onto the percolation head make sure that the slot in the pivoting ring f catches on the left engage the handle of the filter holder in the slot and turn the assembly to the right until it locks click 3 e Turn the function selector d to the W position e Place as large a container as possible below the filter holder You can adjust the height of the grille depending on the size of the container To raise or lower the grille pull horizontally on the support k choose one of the 3 positions and slide the support k horizontally onto the drip tray I 4 As soon as the appliance reaches the right temperature the indicator light of the on off control D e2 becomes fixed w e Press the Up control e7 to start the water running e Repeat this last oper
9. d if malfunction was caused by damage to the product by accident misuse use on frequency or voltage other than marked on the product and or described in the instructions abuse including tampering damage in transit or use for commercial purposes This warranty gives you specific legal rights and you may also have other rights which may vary from state to state GUARANTEE OF PERFORMANCE This fine KRUPS product is manufactured according to a rigid code of quality standards and with minimum care should provide quality service However should the need arise for repairs or for replacement parts within or after the warranty period please call our CONSUMER SERVICE DEPARTMENT USA 800 526 5377 24 hours a day 7 days a week Canada 905 669 0114 Monday Friday 8 00 a m 4 30 p m You will be provided with specific instruction on how to get your product repaired The department will also be able to answer any general product questions you may have Before calling the Consumer Service Department please have the type number of your KRUPS appliance available You must have this information before calling our Consumer Ser vice Department so that we may better answer your questions The type number can be located by looking at the bottom of your appliance This product is Type F927 Any general correspondance can be addressed to USA KRUPS North America Inc P O Box 3900 Peoria IL 61612 Canada KRUPS Service 20 Calda
10. e on off control e2 until the indicator lights come on Release the controls All the indicator lights will flash then go out The scaling monitoring system has taken note of the descaling operation which has just been performed During future use of the machine the H indicator light e1 will remain off until it is again time to descale the machine Notes In the case of serious scaling soak the the grille of the percolation head for 5 minutes in 1 3 of the mixture obtained during the first run through Then rinse and dry it If necessary this operation can also be performed with the steam nozzle e To do this dismantle the nozzle as instructed in the paragraph Maintenance and soak the scaled parts for 5 minutes in 1 3 of the mixture obtained during the first run through Rinse the various parts thoroughly before replacing them Problems likely causes and corrective actions The appliance is not hot enough Wait for the indicator light e2 to stop flashing Leak of coffee around the filter holder The filter holder is not fitted correctly See paragraph Rinsing the water system There is still some coffee on the edge of the filter Clean around the filter and the seal The seal of the Clean the seal percolation head with a damp is dirty cloth The seal of the Contact an percolation head is defective approved KRUPS service center
11. e cups see paragraph Rinsing the water system e The quantity of coffee is already preprogrammed for the preparation of one or two cups To change the pre programmed quantity of coffee refer to the paragraph Programming cup filling Preparing an espresso Your appliance allows you to prepare an espresso using either ground coffee or an ESE measure e Fill the water tank b e Press the on off control e2 and its indicator light will flash e Turn the function selector d to the position UD a Preparing an espresso with ground coffee e Align the arrow located on the filter holder with the desired position by turning the selection ring h1 5 W 1 cup WY 2 cups e Put ground coffee into the filter holder pressing the ground coffee down firmly with the back of the spoon 1 measuring spoon m 1 cup 5 e Clean the edges of the filter holder e Put the filter holder in place 3 e Place one or two espresso cups beneath the filter holder If necessary adjust the height of the grille support 4 As soon as the appliance reaches the right temperature the indicator light on the on off control e2 stops flashing e Press the control e6 OD or the control e7 tp Extraction stops automatically when the preprogrammed quantity of coffee is obtained e Take out the filter holder and remove the ground coffee by pressing the eject
12. e grille support 4 As soon as the appliance reaches the right temperature the indicator light of the on off control D e2 stops flashing e Press the control e6 JP Extraction stops automatically once the preprogrammed quantity of coffee has been obtained e Remove the filter holder and throw away the used measure by pressing the ejection control h2 6 krups 11 Notes To obtain a shorter coffee it is possible to interrupt the automatic cycle at any time by pressing the control e6 To obtain a longer coffee it is possible to prolong extraction after the machine has stopped automatically by holding down the control e6 2 STEAM FUNCTION With the auto cappuccino accessory i you can easily obtain more or less frothy milk to make a cappuccino a caf creme or a hot chocolate heat thick liquids for example soup Practical tips Cappuccino 1 3 coffee 1 3 hot milk 1 3 milk foam Caf cr me 1 2 coffee 1 2 less foamy hot milk Hot chocolate 1 cup of hot milk more or less foamy depending on your taste into which you mix chocolate powder Preparing steam function e Fill the water tank b e Press the control D e2 and its indicator light will flash As soon as the appliance reaches the right temperature the indicator light of the control e2 stops flashing e Press the dy control e4 The indicator light of the on o
13. ff control e2 flashes a Foaming milk e Pour the milk into the tank i4 For best results use cold fresh whole or semi skimmed milk e Place the tank i4 with its lid on the support 15 e Insert the flexible tube i3 into the opening in the lid of the tank The tube must touch the bottom of the container 8 e Turn the tap i1 to the position obtain a fine smooth foam 9a e To obtain less frothy milk turn the tap 11 towards the top of the scale 9b urn to 12 Krups e Place a cup under the nozzle i2 8 If necessary adjust the height of the grille support 4 As soon as the appliance reaches the right temperature the indicator light e2 stops flashing e Turn the function selector d to the dy position until you obtain the required quantity of foamy milk e Turn the function selector d to the JB position and remove the cup Note e Keep the tank i4 containing any unused milk in the fridge b Heating thick liquids e g soup e Turn the tap 11 to the dy position e Immerse the nozzle 12 in the liquid to be reheated 10 If necessary adjust the height of the grille support 4 The tip of the nozzle must not touch the bottom of the container so as not to obstruct the passage of the steam As soon as the appliance reaches the right temperature the indicator light e2 stops flashing e Turn the function selector d to the dy p
14. hen the water tank b is empty e Fill it and resume the last operation in progress Automatic appliance switch off If the appliance is plugged in and the control e2 is activated if no operation is performed for 2 hours the appliance switches itself off automatically all the indicator lights go out To restart the appliance press the control e2 1 ESPRESSO FUNCTION Espresso coffee Espresso coffee is richer in flavour and stronger than a normal coffee It is drunk from small pre heated espresso cups The hot water passes through the ground coffee to obtain this delicious black foamy coffee which has an invigorating effect You can recognize the espresso by its characteristic flavour and its typical foam But this requires high pressure and an excellent espresso coffee which has been well roasted and correctly ground If you are unable to buy ground espresso coffee use a coffee grinder to grind your own beans This coffee must not be ground too fine It should be slightly grainy If it is too fine you run the risk of blocking the grilles of the percolation head and of the filter To guarantee a completely successful espresso it is also necessary to use fresh water i e which has not been standing open to the air for a long time without any odor of chlorine and at a cold enough temperature Tips e For best results preheat the accessories filter holder and cups by running water directly into th
15. in memory and to end the programming procedure If you do not press the memo control e3 within 10 seconds programming stops automatically and the changes are not recorded Maintenance e Unplug the appliance and allow it to cool e Never wash the accessories for your espresso in the dishwasher e Clean the body of the appliance with a damp cloth After use the water tank must be emptied The drip tray I e Each time an espresso is prepared the drip tray fills with water This is perfectly normal If there is any water in the fill indicator 11 you must then empty the drip tray e Remove the grille and its support 11 and empty the drip tray l e If necessary clean the drip tray the grille and its support with water and a little non abrasive dish detergent rinse and dry When reassembling put back the plastic block situated at the back of the tray 12 The percolation head and the filter holder Please note These may be burning hot These must be cleaned after every use All you need to do is run a damp cloth over the percolation head and clean the other accessories with water and a little non abrasive dish detergent Rinse and dry e If the percolation head becomes heavily encrusted unscrew its grille using a coin clean it and replace it tightening it firmly 13 e If the filter holder becomes heavily encrusted unscrew its grille using a coin clean it and replace it tightening i
16. ion control h2 6 Notes To obtain a shorter coffee it is possible to interrupt the automatic cycle at any time by pressing the control e6 or e7 To obtain a longer coffee it is possible to prolong extraction after the machine has stopped automatically by holding down the control e6 or e7 b Preparing an espresso with an ESE measure e Use only measures of the type ESE The E S E system was designed to make an Italian style ristretto pressed espresso for a quantity of coffee between 35 and 50 ml ESE for Easy Serving Espresso simplified preparation of espresso is a measure of selected coffee ground and compacted between two filter papers which makes it ready to use This system simplifies the preparation of an espresso by avoiding the measuring and compressing operations and facilitating the cleaning of the appliance It is neither intended nor recommended that you make a long coffee with these measures We advise that you take care not to deform the ESE measures during handling and storage e Align the arrow on the filter holder with the position 1 cup by turning the selection ring h1 5 e Place the measure in the filter holder fitted with its ESE filter If the measure has a tongue fold down the tongue towards the interior 7 e Put the filter holder in place 3 e Place a cup below the filter holder If necessary adjust the height of th
17. ized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Do not attempt to modify the plug in any way KRUPS 7 8 Thank you for choosing an appliance from the KRUPS range Description a Lid b Removable pivoting water tank c Change cartridge indicator d Function selector e Control panel el limescale indicator light Fl e2 On off switch OD e3 reminder control memo ed Steam control dy e5 Hot water control SL e6 1 cup of coffee control LP e7 2 cups of coffee control cB Swivelling collar g Percolation head h Filter holder h1 selection ring 1 cup ground coffee 1 dose ESE 2 cups ground coffee h2 ejection control i Auto cappuccino accessory 11 tap i2 nozzle i3 flexible tube i4 tank with lid i5 tank support j Grille k Adjustable grille support Drip tray 11 Fill indicator m Measuring spoon n Filtration cartridge n1 fitting key A e Read the instructions for use with care before using your appliance for the first time and retain them for future use any use which does not conform to the Safety instructions KRUPS instructions will absolve KRUPS from any liability e Never leave the appliance within reach of children without supervision The use of this appliance by young children or disabled persons must be supervised at all times e
18. move plug from wall outlet Do not use appliance for other than intended use eUse extreme caution when dispensing hot steam SAVE THESE INSTRUCTIONS 6 Krups CAUTION eThis appliance is for household use only Any servicing other than routine cleaning and user maintenance should be performed by authorized KRUPS service personnel only see Guarantee of Perfor mance eDo not immerse base in water eTo reduce the risk of fire or electric shock do not remove the base of the machine There are no user serviceable parts inside Repairs should be performed by authorized KRUPS service personnel only SPECIAL CORD SET INSTRUCTIONS Regarding your Cord Set A A short power supply cord is provided to reduce risks resulting from entanglement in a longer cord B Longer extension cords are available and may be used if proper care is exercised in their use C Ifa long extension cord is used 1 the marked electrical rating of the extension cord should meet or exceed the electrical rating of the appliance 2 if the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 the longer cord should be arranged so that it will not drape over the counter top or table top where it can be accessed by small children or readily tripped over D This appliance has a polarized plug one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit into a polar
19. ontrol e5 e Run through 1 3 of the mixture by turning the function selector d to the SL position e Then reset the function selector d to 2 and press the control e5 to deactivate the hot water function e Move the container under the percolation head Run through the second third of the mixture by pressing as many times as necessary on the W control e6 e Press the on off control D e2 to turn off the appliance and wait 10 to 15 minutes to allow the descaler to work e Then press the on off control D e2 and its indicator light will flash As soon as the appliance reaches the right temperature the indicator light e2 stops flashing e Press as many times as necessary on the W control e6 to allow the rest of the mixture to run through into the container placed beneath the percolation head e Run through two tanks of fresh water to rinse the percolation head and the nozzle See paragraph Rinsing the water system e Replace the grille on the percolation head see Maintenance section e Refit the filtration cartridge see Before first use section It is now necessary to inform the scale monitoring system that the descaling operation has been performed To do this The appliance must be plugged in but the on off control D e2 is not activated indicator light off e Press simultaneously on the gt control e7 and on th
20. osition until the liquid is hot enough then reset the function selector d to the JB position and remove the container Important notes e After using the steam function press the dy control e4 to deactivate this function The appliance will cool itself down automatically until it reaches the correct temperature to return to the espresso function elf you do not press the dy control e4 within about 2 minutes after using the steam function the appliance will cool itself down automatically to return to the espresso function e The intermittent noise produced during the preparation of steam is caused by the pump being regulated and has nothing to do with the correct operation of the appliance e During and after operation of the appliance the nozzle i2 is very hot e We would recommend that you clean the auto cappuccino accessory immediately after use see Maintenance section 3 HOT WATER FUNCTION Warning In certain cases steam may come out of the nozzle before any hot water is obtained e Fill the water tank b e Press the control on off control D e2 and its indicator light will flash e Turn the tap 11 to the dy position e Place the container under the nozzle i2 8 If necessary adjust the height of the grille support 4 The tip must not touch the bottom of the container so as not to obstruct the passage of the water As soon as the appliance reaches
21. ri Rd Concord Ontario L4K 4N8 krups 17
22. t firmly 14 krups 13 The seal for the percolation head When you are not using your espresso do not leave the filter holder in the appliance in order to prevent wear on the seal e Clean the seal regularly using a damp cloth Auto cappuccino accessory After each use we advise you to rinse the auto cappuccino accessory as follows e Press the dj control e4 The indicator light e2 will flash e Turn the tap 11 to the 4 position e immerse the flexible tube i3 into the clean tank i4 1 3 full of water e Place a container under the nozzle i2 If necessary adjust the height of the grille support 4 The tip must not touch the bottom of the container so as not to obstruct the passage of the water As soon as the appliance reaches the right temperature the indicator light of the control e2 stops flashing e Turn the function selector d to the dy position e When all the water has run through turn the function selector d to the LW position and press the gy control e4 e Next clean the nozzle i2 with a damp cloth We advise you to completely dismantle the auto cappuccino accessory at regular intervals and clean it with water a little non abrasive dish detergent and a small brush Rinse and dry it before refitting it 15 Please note the direction of fitting the flexible tube engage the straight cut end in the auto cappuccino accessory Descaling It is vital
23. the hardness of the water in your area use the stick supplied with the appliance You will also find this stick in the KRUPS descaling accessory reference no 054 which is available from approved KRUPS service center The appliance is delivered with the pre set 3 as descaling interval Adjustment e Dip the stick in cold water for one second Shake off the excess water and work out the hardness according to the number of pink zones showing on the stick e Using the following table determine the adjustment you need to make depending on whether or not you are using the filtration cartridge n Pink zones Descaling interval on stick With filtration Without filtration cartridge cartridge 00 1 1 2 1 2 3 2 3 4 2 4 e Plug in the appliance e Press simultaneously on the memo control e3 and on the on off switch D e2 until the EJ indicator light e1 flashes Then release the controls The descaling interval selected is indicated by the number of indicator lights which are lit E g the interval 3 is indicated by the El indicator light e1 flashing and the lighting of 3 indicators on the control panel e Set the desired descaling interval by pressing he corresponding control nterval 1 PO control e6 nterval2 D control e7 nterval3 ML control e5 nterval 4 gl control e4 Press the memo control e3 to store your sele
24. the right temperature the indicator light of the control e2 stops flashing e Press the J control e5 e Turn the function selector d to the ML position e Once the quantity of water required is obtained turn the function selector d to the W position Notes e After using the hot water function press the M control e5 to deactivate this function The appliance will cool itself down automatically until it reaches the correct temperature to return to the espresso function e If you do not press the control e5 within about 2 minutes after using the hot water function the appliance will cool itself down automatically to return to the espresso function 4 PROGRAMMING CUP FILL This function allows you to programme the quantity of coffee you want for each of the espressos prepared The appliance is preprogrammed for a quantity of 50 ml per cup This programming is to be done while an espresso is being made e Prepare the appliance to make one or 2 cups of espresso see paragraph Espresso function As soon as the appliance reaches the right temperature the indicator light of the control O e2 stops flashing e Press the memo control e3 Its indicator light will flash e Hold down the control e6 D or the control e7 co until you obtain the desired quantity of espresso e Press again on the memo control e3 to store this quantity of coffee
Download Pdf Manuals
Related Search