Intimidator Spot LED 350
Contents
1. Power Out PMX Out Power In DMX In Fuse Holder Intimidator Spot LED 350 User Manual Rev 5 Page 5 of 20 154 in 392mm AC Power The Intimidator Spot LED 350 has an auto ranging power supply and it can work with an input voltage range of 100 240 VAC 50 60 Hz To determine the product s power requirements circuit breaker power outlet and wiring use the current value listed on the label affixed to the product s back panel or refer to the product s specifications chart The listed current rating indicates the product s average current draw under normal conditions i Always connect the product to a protected circuit circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Fuse Replacement IN Disconnect the product from power before replacing the fuse 1 Disconnect this product from power 2 Using Phillips 2 head screwdriver unscrew the fuse holder cap from the housing 3 Remove the blown fuse 4 Replace with a good fuse of the same type and rating 5 Screw the fuse holder cap back in place and reconnect power AN Always replace a blown fuse with one of the same type and2. 1135 119 Orange Dark Blue 120 127 Dark Blue White 128 5 191 Color cycling rainbow with increasing speed 192 255 Reverse color cycling rainbow with increasing speed Gobo Wheel 0 7 60 8 1 40 47 48 35 56 63 064 071 Gobo 7 shake from slow to fast 072 5 079 Gobo 6 shake from slow to fast 080 087 Gobo 5 shake from slow to fast 088 095 Gobo 4 shake from slow to fast 096 103 Gobo 3 shake from slow to fast 104 111 Gobo 2 shake from slow to fast 1128 119 Gobo 1 shake from slow to fast 120 127 Open 128 amp 191 Cycle effect with increasing speed 192 255 Reverse cycle effect with increasing speed Page 12 of 20 Intimidator Spot LED 350 User Manual Rev 5 DMX Channel Assignments and Values cont 14 CH cont Channel Function Value Setting Gobo Rotation 000 063 Indexing 064 147 Rotation effect with increasing speed 148 231 Reverse rotation effect with increasing speed 232 255 Gobo bounce Prism 000 007 Open 008 012 Prism on 013 130 Prism rotation with increasing speed 131 247 Reverse prism rotation with increasing speed 248 255 Prism effect 10 Focus 000 255 Motor focus zoom out to Zoom in T Dimmer 000
3. will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number The RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility FedEx packing or double boxing are recommended CHAUVET reserves the right to use its own discretion to repair or replace returned product s World Headquarters United Kingdom amp Ireland CHAUVET CHAUVET Europe Ltd General Information General Information Address 5200 NW 108th Avenue Address Unit 1C Sunrise FL 33351 Brookhill Road Industrial Estate Voice 954 577 4455 Pinxton Nottingham UK Fax 954 929 5560 NG16 6NT Toli free 800 762 1084 Voice 44 0 1773 511115 Fax 44 0 1773 511110 Technical Support Technical Support Voice 954 577 4455 Press 4 Emai uktech chauvetliahting com Fax 954 756 8015 Email tech chauvetlighting com World Wide Web www chauvetlighting com World Wide Web www chauvetlighting co uk Intimidator Spot LED 350 User Manual Rev 5 Page 19 of 20 6 TECHNICAL SPECIFICATIONS Dimensions and Weight Power Light Source Photo Optic Thermal DMX Ordering
4. Length Width Height 10 6 in 268 mm 13 4 in 340 mm 184 in 392 mm Note Dimensions in inches rounded to the nearest decimal digit Power Supply Type Switching internal Parameter Consumption Operating Power linking units Fuse Power I O Power input connector Power output connector Power Cord plug Type LED Color White Parameter luminance 12 Zoom angle Strobe Rate Pan amp Tilt Pan Tit Ranges Gobo Size Maximum External Temp 104 F 40 C VO Connectors pin XLR Product Name Intimidator Spot LED 350 Range 100 240 V 50 60 Hz 120 V 60 Hz 272W 22A 3 units F3A 250V USMoridwide IEC Edison Edison US Power TOW 17 A Quantity 1 9490 Ix 2417 0 20 Hz 540 540 360 180 Pan 24 mm outside 20 mm image 1 1 mm thickness Cooling System Convection Connector Type Sockets Item Code 08010463 Weight 22 7 Ibs 10 3 kg Voltage Selection Auto ranging 230 V 50 Hz 285W 12A 7 units F3A 250V UK Europe IEC IEC Local plug Lifespan 50 000 hours Current 350 mA 270 270 180 90 Tit Channel Range 8 14 Item Number INTSPOTLED350 Page 20 of 20 Intimidator Spot LED 350 User Manual Rev 5
5. do the following 1 Press lt MODE ESC gt repeatedly until 001 shows on the display 2 Press ENTER 3 Use UP or DOWN to select the starting address 4 Press ENTER The Intimidator Spot LED 350 has two DMX personalities an 8 channel personality and a 14 channel personality To choose which DMX personality to use follow the steps below 1 Press lt MODE ESC gt repeatedly until either 14CH to choose the 14 channel personality or 8CH to choose the 8 channel personality shows on the display 2 Press ENTER Intimidator Spot LED 350 User Manual Rev 5 Page 11 of 20 DMX Channel Assignments and Values 14 CH Channel Function Value Setting 1 Pan 000 255 0 540 Fine Pan 000 5 255 Fine control of panning Tit 000 255 0 270 Fine Tilt 000 255 Fine control of tilting PISIS Speed 000 255 Pan Tilt speed fast to slow Color Wheel 000 006 White 007 5 013 Yellow 014 020 Pink 021 5 027 Green 028 5 034 Red 035 041 Light Blue 042 048 Kelly Green 049 5 055 Orange 056 5 063 Dark Blue 064 070 White Yellow 071 077 Yellow Pink 078 5 084 Pink Green 085 091 Green Red 092 098 Red Light Blue 099 amp 105 Light Blue Kelly Green 106 5 112 Kelly Green Orange
6. in place and remove the gobo from the gobo plate 8 Inserta new gobo and hold it in place with the expansion ring 9 To re insert the new gobos slide the tip of the gobo holder under the pressure plate near the center of the gobo wheel 10 Push the gobo holder assembly inwards DO NOT force the gobo holder into the gobo wheel slot Slightly move the holder from side to side if needed to get it to seat properly If correctly installed the bottom of the holder will be flush with the gobo wheel 11 Push cover back into position Gobo Replacement Diagram Gobo Holder Removal Expansion Ring Gobo Holder Assembly Pressure plate Gobo Wheel Detail Views Intimidator Spot LED 350 User Manual Rev 5 Page 17 of 20 5 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can Mai lead to reduction of the light source s life To maintain optimum performance and jaintenanCe minimize wear you should clean your lighting products at least twice a month However be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency To dean the product follow the instructions below Unplug the product from power Wait until the product is cold Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents Clean all glass transparent surfaces with a mild soap
7. solution ammonia free glass cleaner or isopropyl alcohol Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue Softly drag any dirt or grime to the outside of the glass transparent surface Gently polish the glass transparent surfaces until they are free of haze and lint Always dry the glass transparent surfaces carefully after cleaning them Page 18 of 20 Intimidator Spot LED 350 User Manual Rev 5 Contact Us To return a product or request support In the U S contact CHAUVET World Headquarters see below Inthe UK or Ireland contact CHAUVET Europe Ltd see below In any other country DO NOT contact CHAUVET Contact your distributor See www chauvetlighting com for distributors outside the U S United Kingdom or Ireland Outside the U S United Kingdom or Ireland contact your distributor and follow their instructions on how to return CHAUVET products to them Visit our website for contact details Call the corresponding CHAUVET Technical Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return You must send the merchandise prepaid in its original box and with its original packing and accessories CHAUVET will not issue call tags Clearly label the package with the RMA number CHAUVET
8. 255 0 100 12 Shutter 000 amp 003 Closed 004 007 Open 008 076 Strobe effect with increasing speed O77 145 Pulse strobe 446 215 Random shutter 216 255 Open 13 Control Functions 000 007 No function 008 015 Blackout while pan ti moving 016 023 Blackout while moving color wheel 024 031 Blackout while moving gobo wheel 032 039 Disable blackout while panitil moving color wheel 040 047 Disable blackout while panitilUmoving gobo wheel 048 055 Disable blackout while moving all options 056 095 No function 096 103 Reset pan 104 6 111 Reset tit 112 119 Reset color wheel 120 127 Reset gobo wheel 128 135 Reset gobo rotation 136 143 Reset prism 144 151 Reset focus 182 159 Reset all channels 160 255 No function D Movement Macros 000 5 007 No function 008 023 Movement macro 1 024 039 Movement macro 2 040 055 Movement macro 3 056 071 Movement macro 4 072 087 Movement macro 5 088 103 Movement macro 6 104 119 Movement macro 7 120 135 Movement macro 8 136 151 Sound controlled program 1 182 167 Sound controlled program 2 168 183 Sound controlled pr
9. INTIMIDATOR SPOT LED 350 User Manual Valve Innovation Performance Green Thinking TABLE OF CONTENTS 1 Before You Begin What Is Included Unpacking Instructions Claims Text Conventions Symbols Document Information Product at a Glance Safety Notes 2 Introduction Product Overview Product Dimensions 3 Setup AC Power Fuse Replacement Power Linking Mounting Orientation Rigging 4 Operation Control Panel Operation Menu Map Configuration DMX Starting Address DMX Personalities 3 DMX Channel Assignments and Values TA OB iios decreta a tarte 12 DMX Channel Assignments and Values cont 43 Bree 14 Configuration Standalone Sound Active Mode Automatic Mode Manual Pan Tilt Operation Pan Tilt Angle Restrict Display Master Slave Mode Reset Software Password Channel Changing Gobos 5 Technical Information Product Maintenance Returns Contact Us 6 Technical Spe Page 2 of 20 Intimidator Spot LED 350 User Manual Rev 5 1 BEFORE YOU BEGIN What IS _Intimidator Spot LED 350 Warranty Card Included Power Cord Quick Reference Guide Unpacking Carefully unpack the product immediately and check the container to make sure all the Instructions Parts are in the package and are in good condition Claims f the box or the contents the
10. e are several options for adjustment Parameter Programming Steps Description Pan Adjust P128 Manually adjust the pan angle Tilt Adjust 1128 Manually adjust the tilt angle Gobo Wheel Adjust G128 Manually adjust the gobo wheel Color Wheel Adjust C128 Manually adjust the color wheel Focus Adjust F128 Manually adjust the focus Prism Adjust L000 Manually adjust the prism Lamp Brightness Adjust 4000 Manually adjust the starting brightness of the lamp Page 16 of 20 Intimidator Spot LED 350 User Manual Rev 5 Changing To change the gobos in the Intimidator Spot LED 350 do not remove the gobo wheel Simply Gobos jun off and disconnect product from power outlet 2 Place the product on a flat level surface with the front facing up 3 Access the gobo plate by removing the cover on the moving head By hand gently pry up the right side then push right with the indented handles NOTE If you expose the driver board you are on the wrong side of the head Replace the cover immediately and remove the cover on the opposite side of the moving head 4 Rotate the gobo wheel until the gobo that needs replacing is accessible 5 Separate the gobo holder assembly away from the gobo wheel by pushing it forward and up Be careful not to push the gobo out of the gobo plate 6 Extract the gobo holder by pulling it backwards out of the product 7 On a flat surface remove the expansion ring that holds the gobo
11. e of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product The product is for indoor use only IP20 To prevent risk of fire or shock do not expose the product to rain or moisture Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots on the product s housing are blocked Never connect the product to a dimmer Make sure to replace the fuse with another of the same type and rating Never carry the product from the power cord or any moving part Always use the hanging mounting bracket or the handles The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center 9 Keep this User Manual for future use If you sell the product to another user be sure to give this document to the next owner Page 4 of 20 Intimidator Spot LED 350 User Manual Rev 5 2 INTRODUCTION Product Overview Control Panel and Safety Loop Button Menu
12. he Intimidator Spot LED 350 to Restrict 2chieve the effect you like To select which pan angle to use do the following 1 Press MODE ESC repeatedly until PASA shows on the display 2 Press UP or DOWN to select either 540 PA54 360 PA36 or 180 PA18 3 Press ENTER To select which tilt angle to use do the following 1 Press lt MODE ESC gt repeatedly until Ti27 shows on the display 2 Press UP or DOWN to select either 270 Ti27 180 Ti18 or 90 Ti 9 3 Press ENTER Display You are able to flip the LED display for easy readability in any mounting situation To select your display angle 1 Press MODE ESC repeatedly until diS shows on the display 2 Press UP or DOWN to select normal display mode diS or inverse display mode r dis 3 Press ENTER Intimidator Spot LED 350 User Manual Rev 5 Page 15 of 20 Master Slave The Master Slave mode allows a single Intimidator Spot LED 350 unit the master to Mode control the actions of one or more Intimidator Spot LED 350 units the slaves without the need of a DMX controller The master unit will be set to operate in either Automatic or Sound Active mode while the slave units will be set to operate in Slave Mode Once set and connected the slave units will operate in unison with the master unit Configure the units as indicated below Slave units 4 Press lt MODE ESC gt repeatedly unti
13. l Pan operation an Inverse Pan rPAn Inverse Pan operation Normal Tilt tiL Normal Tilt operation i Inverse Tilt FtiL Inverse Tit operation Normal dis Display Display Change the LCD display text position Inverse a f rdis Display 14 Channel ie 44CH Channel Mode Selects the DMX personality 8 Channel do Mode Pan 540 PASA Manual Pan Pan 360 PA36 Select Pan angle restrictions Restrict Pan 180 PAIS Tilt 270 Ti27 Manual Tilt Tilt 180 Ti18 Select Tilt angle restrictions Restrict Tilt 90 Tis Reset Est Resets fixture Load Load Load factory defaults Page 10 of 20 Intimidator Spot LED 350 User Manual Rev 5 Configuration DMX Starting Address DMX Personal Set the product in DMX mode to control with a DMX controller 1 Connect the product to a suitable power outlet 2 Turn the product on 3 Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels The Intimidator Spot LED 350 uses up to 14 DMX channels in its 14 channel DMX mode which defines the highest configurable address to 499 If you are not familiar with the DMX protocol download the DMX Primer from www chauvetlighting com To select the starting address
14. l SLAv shows on the display 2 Press ENTER to accept 3 Set the DMX address to 001 4 Connect the DMX input of the first slave unit to the DMX output of the master unit 5 Connect the DMX input of the subsequent slave units to the DMX output of the previous slave unit 6 Finish setting and connecting all the slave units Master unit 1 Set the master unit to operate in either Automatic or Sound mode 2 Make the master unit the first unit in the DMX daisy chain Configure all the slave units before connecting the master unit to the DMX daisy chain Never connect a DMX controller to a DMX string configured for Master Slave operation because the controller may interfere with the signals from the master unit Do not connect more than 31 slave units to the master unit Reset Software To reset the software on the Intimidator Spot LED 350 do the following 1 Press lt MODE ESC gt repeatedly until rESt shows on the display 2 Press ENTER The product will reset all settings in the software to the default factory settings Password The Intimidator Spot LED 350 contains a password protected mode which allows you to calibrate and troubleshoot any small issues you may have during normal operation Channel er to access this mode do the following 1 Press and hold lt MODE ESC gt for at least 10 seconds 2 Use the UP and DOWN buttons to enter the password 2323 3 Press ENTER In this mode ther
15. ntroller Sound Active To enable the Sound Active mode do the following Mode 1 Press MODE ESC repeatedly until one of the following shows on the display NASI NAFA NStS SLAv 2 Press UP or DOWN to select NStS 3 Press ENTER 4 Turn the music on and adjust the microphone sensitivity knob until the product starts responding to the beat of the music The product will only respond to low frequencies of music bass and drums Automatic Mode To enable the Automatic Mode 1 Press lt MODE ESC gt repeatedly until one of the following shows on the display NASI NAFA NStS SLAv 2 Press UP or DOWN to select NASI for a slow light show or NAFA for a fast light show 3 Press ENTER Manual Pan Tilt To select whether you want the Intimidator Spot LED 350 to operate with normal Operation Panning or inverted panning do the following 1 Press lt MODE ESC gt repeatedly until PAn shows on the display 2 Press UP or DOWN to select normal pan operation PAn or inverse pan operation r PAn 3 Press ENTER To select whether you want the Intimidator Spot LED 350 to operate with normal tiling or inverted tilting do the following 1 Press lt MODE ESC gt repeatedly until tiL shows on the display 2 Press UP or DOWN to select normal pan operation tiL or inverse pan operation r tiL 3 Press ENTER Pan Tilt Angle You are able to restrict the pan and tilt angles on t
16. ocument to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com Copyright 2012 CHAUVET All rights reserved Electronically published by CHAUVET in the United States of America Author Date Editor Date A Diaz mm S Diaz 91242 Intimidator Spot LED 350 User Manual Rev 5 Page 3 of 20 Product at a Use on Dimmer _ f Auto Programs Y Glance Outdoor Use fAuto ranging Power Supply Y Sound Activated v Replaceable Fuse Y DMX v User Serviceable S Master Slave v Duty cyce Safety Notes These notes include important information about the mounting usage and maintenance of this product read before using the product This product is not intended for permanent installation Always connect the product to a grounded circuit to avoid the risk of electrocution Always disconnect the product from power before cleaning or replacing the fuse Avoid direct eye exposure to the light source while the product is on Make sure the power cord is not crimped or damaged Never disconnect the product from power by pulling or tugging on the cord If mounting the product overhead always secure to a fastening device using a safety cable Make sure there are no flammable materials close to the product when operating Do not touch the product s housing when operating because it may be very hot A Always make sure that the voltag
17. ogram 3 184 199 Sound controlled program 4 200 215 Sound controlled program 5 216 231 Sound controlled program 6 282 247 Sound controlled program 7 248 255 Sound controlled program 8 Intimidator Spot LED 350 User Manual Rev 5 Page 13 of 20 8 CH Channel Function Value Setting 1 Pan 000 255 0 540 2 t 000 255 0 2707 Color Wheel 000 5 006 Write 007 amp 013 Yellow 014 020 Pink O21 5 027 Green 028 034 Red 035 041 Light Blue 042 5 048 Kelly Green 049 055 Orange 056 5 063 Dark Blue 064 5 070 White Yellow 071 077 Yellow Pink 078 084 Pink Green 085 5 091 Green Red 092 5 098 Red Light Blue 099 105 Light Blue Kelly Green 106 112 Kelly Green Orange 13e 119 Orange Dark Blue 120 127 Dark Blue White 128 5 191 Color cycling rainbow with increasing speed 192 255 Reverse color cycling with increasing speed Gobo Wheel 6 16 23 2431 d gt 6 40 47 56 63 064 071 Gobo 7 shake from slow to fast 072 amp 079 Gobo 6 shake from slow to fast 080 5 087 Gobo 5 shake from slow to fast 088 095 Gobo 4 shake from slow to fast 096 5 103 Gobo 3
18. product and included accessories appear damaged from shipping or show signs of mishandling notify the carrier immediately not CHAUVET Failure to report damage to the carrier immediately may invalidate your claim In addition keep the box and contents for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with CHAUVET within 7 days of delivery Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings menu option not to be modified Menu gt Settings A sequence of menu options to be followed ENTER A key to be pressed on the product s control panel ON A value to be entered or selected Symbols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Important installation or configuration information The product may not function correctly if this information is not used Useful information Document The information and specifications contained in this document are subject lo change without notice CHAUVET assumes no responsibilty or liability for any errors or Information omissions that may appear in this manual CHAUVET reserves the right to update the existing document or to create a new d
19. rating Intimidator Spot LED 350 User Manual Rev 5 Page 7 of 20 Power Linking The product provides power linking via the IEC outlet located in the back of the unit Power Linking Diagram gt 3 Product Other products You can power link up to 3 Intimidator Spot LED 350 units on 120 VAC or up to 7 Intimidator Spot LED 350 units on 230 VAC The power linking diagram shown above corresponds to the North American version of the product ONLY If using the product in other markets you must consult with the local CHAUVET distributor as power linking connectors and requirements may differ in your country or region Page 8 of 20 Intimidator Spot LED 350 User Manual Rev 5 Mounting Orientation Rigging Mounting Diagram Before mounting the product read and follow the safety recommendations indicated in the Safety Notes The Intimidator Spot LED 350 may be mounted in any position however make sure adequate ventilation is provided around the product Before deciding on a location for the product always make sure there is easy access to the product for maintenance and programming purposes Make sure that the structure or surface onto which you are mounting the product can support the products weight See the Technical Specifications for weight information When mounting the product overhead always use a safety cable Mount the product
20. securely to a rigging point whether an elevated platform or a truss When rigging the product onto a truss you should use a mounting clamp of appropriate weight capacity When power linking multiple products you must always consider the length of the power linking cable and mount the products close enough for the cable to reach The rubber feet also serve as floor supports When mounting the product on the floor make sure that the product and cables are away from people and vehicles Bracket Attachment x2 Rubber Feet x4 Safety Loop Attachment Point Intimidator Spot LED 350 User Manual Rev 5 Page 9 of 20 4 OPERATION Control Panel To access the control panel functions use the four buttons located underneath the display Operation Button Function lt MODE ESC gt rel to find an operation mode or to back out of the current menu lt UP gt Press to scroll up the list of options or to find a higher value DOWN Press to scroll down the list of options or to find a lower value lt ENTER gt Press to activate a menu option or a selected value Menu Map Mode Programming Steps Description DMX Mode 001 512 Sets the DMX starting address SLAv Son Slave operating mode Operation NASL SLoU Automatic mode Slow program Modes NAFA FASt Automatic mode Fast program NStS SrUn Sound Aative mode x Normal Pan PAn Norma
21. shake from slow to fast 104 5111 Gobo 2 shake from slow to fast 1128 119 Gobo 1 shake from slow to fast 120 127 Open 128 amp 191 Cycle effect with increasing speed 192 255 Reverse cycle effect with increasing speed Gobo Rotation 000 5 063 Indexing 064 amp 147 Rotation effect with increasing speed 148 231 Reverse rotation effect with increasing speed 232 255 Gobo bounce Prism 000 5 007 Open 008 amp 012 Prism on 013 amp 130 Prism rotation with increasing speed 131 247 Reverse prism rotation with increasing speed 248 255 Prism effect Focus 000 255 Motor focus zoom out to zoom in Shutter 000 003 Closed 004 007 Open 008 5 076 Strobe effect wilh increasing speed 077 145 Pulse strobe 146 215 Random shutter 216 255 Open Page 14 of 20 Intimidator Spot LED 350 User Manual Rev 5 Configuration Set the product in one of the standalone modes to control without a DMX controller Standalone 1 Connect the product to a suitable power outlet 2 Tum the product on Never connect a product that is operating in any standalone mode either Automatic or Sound to a DMX string connected to a DMX controller Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the co
Download Pdf Manuals
Related Search