ImproX IXP20 Controller
Contents
1. IXP20 System Product Specification Catalogue The ImproX IXP20 is a fully featured stand alone Access Control System supporting up to 1 000 Tagholders and 5 000 transactions Designed for ease of use the IXP20 System allows for the real time monitoring and controlling of residential as well as small or medium commercial and industrial sites The IXP20 Controller built on either an ImproX iTT or iT RT Door Controller platform allows connection of 2 Readers direct to the Controller The System is easily expanded to up to 8 Doors all in Anti passback APB Mode The IXP20 System offers an easy upgrade path with a simple firmware change enabling it to be included in a larger IXP System Housed in an ABS Plastic cabinet the IXP20 Controller is available in 4 models to best suit your individual needs e Models ISC910 and ISC920 offer a cost effective Ethernet connection and an easy to use Web Interface These models only need an internet browser to interact with the Controller and offer the added ability to backup your Database to PC IXP20 Net also provides access to various Web based Reports e Models ISC911 and ISC921 do not need a PC connection Boasting a two and a half inch Graphics Touch Screen these models allow complete System configuration at the Controller in addition to the standard Web UI A Screen Lock and Password option ensure your settings remain secure The IXP20 Touch also provides access to various Co2. Global Corporation an ASSA ABLOY Group Brand e 16 step Auto tune allows for cable distances of up to 25 m 82 ft for Non keypad Antenna Readers and up to 16 m 53 ft for Keypad Antenna Readers e Connection to up to two Antenna Readers per Controller allowing Relaxed or Full Anti passback APB access EN impro technologies ACCESS CONTROL ISC920 and ISC921 ImproX iTRT Platform e Interfaces to the following ImproX Readers ImproX Multi discipline Readers ImproX Wiegand Reader e Offers full Wiegand Support e Interfaces with the ImproX RF Receiver e Peripheral read capability using the following Tags Slim Tags Omega Tags Mifare Standard Mifare Ultralite FeliCa Desfire HID iClass Philips HITAG 1 and Philips HITAG 2 CAUTION The IXP20 System does not support the use of HID 1346 Proxkey II Tags NOTE HID FeliCa and MIFARE are registered trademarks of HID Global Corporation an ASSA ABLOY Group Brand The Sony Corporation and Koninklijke Phillips Electronics N V respectively e Connection to up to two Readers or Third party Devices per Controller allowing Relaxed or Full Anti passback APB access Reading Range Tag The following Tag read ranges apply to the ISC911 and ISC921 models internal registration reader only Tag Type Typical Range mm Typical Range in Slim Tags Up to 25 Up to 1 Omega Tags Up to 25 Up to 1 Impro Trinary Tags Up to 25 Up to 1 HID 125 kHz Tag
3. Switch Reader Frequency Reader Read Capability 2 Independent single pole double throw SPDT Relays each with NO COM and NC contacts 10 A at 28 V DC 5 A at 220 V AC 12 A at 120 V AC 100 000 Minimum 1 Internal Switch 125 kHz Slim Tags Omega Tags Philips HITAG 1 Philips HITAG 2 and HID 125 kHz Tags CAUTION The IXP20 System does not support the use of HID 1346 Proxkey II Tags Electrical Specifications ImproX iTRT Platform Power Input Voltage 10 V DC to 30 V DC polarity sensitive Power Requirements ISC920 12 V DC with no peripherals connected and relays off 24 V DC with no peripherals connected and relays off Current mA Power W 75 0 90 40 0 96 Power Requirements ISC921 12 V DC with no peripherals connected and relays off 24 V DC with no peripherals connected and relays off Relay Power Requirements Permissible Input Supply Ripple Voltage Max Power Input Protection Current mA Power W 130 1 56 60 1 44 An additional 0 4 W per Relay in use 1V pp at 50 HZ Reverse polarity over voltage and over current protection are provided on the Terminal Real Time Clock Backup Battery RTC Battery Type Battery Life Ethernet Port Connection Protocol RS485 Terminal Bus Electrical Interface Baud Rate Data Format Communications Protocol Line Termination 1 x 3 V CR2032 Lithium cell battery 2 Years with power OFF 5 ye
4. ars with power ON 5 years storage with Battery Tab in place Standard Ethernet RJ45 connector 10 100 Base T half or full duplex ImproX Proprietary Protocol RS485 38 400 8 data bits no parity 1 stop bit ImproX Secure Communications Protocol Provision is made for line termination Reader Options Reader 1 Wiegand and Reader 2 Wiegand allow connection to the ImproX Multi discipline Readers and Wiegand Readers The function is selectable via the DIP switches Power Output Modes Supported Baud Rate Data Format Electrical Interface Communications Protocol Digital Inputs General Input Type Detection Resistance Range Protection Range Door Lock Input Type Protection Range Relays Relay Output Contact Ratings Operations General Anti tamper Switch Reader Frequency Reader Read Capability 12 V DC and 5 V DC selectable at maximum 200 mA Tag PIN code or Reason Code 9 600 8 data bits no parity 1 stop bit TTL Full Duplex ImproX Proprietary Protocol 4 Dry contact inputs lt 2 kOhm 15 V continuous 2 Dry contact inputs 15 V continuous 2 Relays Form C each with NO COM and NC contacts 10 A at 28 V DC 5 A at 220 V AC 10 A at 120 V AC 100 000 Minimum 1 Internal Switch 125 kHz and 13 56 MHz Slim Tags Omega Tags Mifare Standard Mifare Ultralite FeliCa Desfire HID iClass Philips HITAG 1 and Philips HITAG 2 CAUTION T
5. he IXP20 System does not support the use of HID 1346 Proxkey II Tags NOTE Because of the way standard Wiegand Readers handle HID Tag codes IXP20 Sites using standard Wiegand Readers can only support one of two options HID Tags only or other 125 kHz Tag types such as Slim Tags Omega Tags Philips HITAG 1 and Philips HITAG 2 depending on the Reader For HID Tags only set the DIP switch to Wiegand Open Format and the Wiegand Reader to HID Raw Mode For any other Tag type set the DIP switch to Wiegand 26 bit 44 bit For more information refer to the Installation Manual for the IXP20 Controller iTRT Platform If you need a combination of HID Tags and other Tag types make use of the ImproX Multi discipline Readers User Interfaces Touch Screen ISC911 and ISC921 Only Type Resolution Colour Back lighting Buzzer Volume and Tone Thin Film Transistor Liquid Crystal Display TFT LCD 240 x 320 Pixels 65 K Colour Screen Permanently on Single tone with a 3 step adjustable volume Page 3 Controller Status Indicator Status LED Upgrade Mode RS485 Communications Failure Diagnostic Indicators Relay 2 Relay 1 Reader 2 RTE 2 Reader 2 DOS 1 Reader 1 RTE 2 Reader 1 DOS 1 RS485 RX RS485 TX Locked Unlocked Enet Act Ethernet Activity Enet Spd Ethernet Speed Enet Lnk Ethernet Link Related Information Continuous Red Flashing Red Steady Flashing Red I
6. nnas attached Input Voltage 12 V DC with Antennas attached Input Voltage 24 V DC with Antennas attached Relay Power Requirements Permissible Input Supply Ripple Voltage Max Power Input Protection Current mA Power W 140 1 68 65 156 150 1 8 75 1 8 An additional 0 4 W per Relay in use 1V pp at 50 Hz Reverse polarity over voltage and over current protection are provided on the Terminal Real Time Clock Backup Battery RTC Battery Type Battery Life Ethernet Port Connection Protocol RS485 Terminal Bus Electrical Interface Baud Rate Data Format Communications Protocol Line Termination R8485 Unit Status Reader Options Antenna Port Digital Inputs Input Type Detection Resistance Range Protection Range Door Lock Input Type Protection Range 1 x 3 V CR2032 Lithium cell battery 2 Years with power OFF 5 years with power ON 5 years storage with Battery Tab in place Standard Ethernet RJ45 connector 10 100 Base T half or full duplex ImproX Proprietary Protocol RS485 38 400 8 data bits no parity 1 stop bit ImproX Secure Communications Protocol Provision is made for line termination Slave 2 Fully functional Antenna Reader Ports 4 Dry contact Digital Inputs lt 2 kOhm 15 V continuous 2 Dry contact inputs 15 V continuous Page 2 Relays Relay Output Contact Ratings Operations General Anti tamper
7. ntermittent Continuous Red on activation of the Relay Continuous Red on activation of the Relay Continuous Green on detected contact closure Continuous Green on detected contact closure Continuous Green on detected contact closure Continuous Green on detected contact closure Flashing Green as per incoming data Flashing Red as per outgoing data Continuous Green when locked Continuous Green when unlocked Flashing Red LED Continuous Red for 100 Mbps Default Off for 10 Mbps Continuous Red on connection to network For extra information relating to this product refer to the IXP20 Controller ImproX iTT Platform Hardware Installation Manual ISC304 0 0 GB XX IXP20 Controller ImproX iTRT Platform Hardware Installation Manual ISC304 0 0 GB XxX IXP20 Touch User Manual ISC305 0 0 GB XX IXP20 Net User Manual ISC306 0 0 GB XX Ordering Information Order the IXP20 Controller using the following Part Numbers ISC910 1 0 GB XX ImproX IXP20 Twin Antenna Controller with Web Interface ISC911 5 0 GB XX ImproX IXP20 Twin Antenna Controller with Touch Screen ISC920 0 0 GB XX ImproX IXP20 Twin Reader Controller with Web Interface ISC921 5 0 GB XX ImproX IXP20 Twin Reader Controller with Touch Screen Warranty Details CAUTION We reserve the right to nullify the products warranty where you have not properly installed the Metal oxide Varistors This product conforms to ou
8. ntroller based Reports Key Features General e Operates at 10 to 30 V DC e System support for up to 8 Doors on the RS485 Terminal Bus e Supports up to 1 000 Tagholders ImproX IXP20 System ISC910 1 0 GB XX ISC911 5 0 GB XX ISC920 0 0 GB XX ISC921 5 0 GB XX General Continued e Support for up to 3 Tags per Tagholder e Buffers up to 5 000 Transactions e 2 Reader Fixed Addresses reserved for the Controller e Support for up to 16 Reader Fixed Addresses allowing for connection of up to 8 Terminals e An RS485 Terminal Communications Bus allowing connection to the ImproX iTT Intelligent Twin Antenna Terminal and the ImproxX iTRT Intelligent Twin Reader Terminal e Uses AES 128 bit Encryption through a Diffie Hellman key exchange to ensure secure communications e A TCP IP Bus which links the System Controller to the Host PC e End of Line EOL Sensing on Door Open Sensor DOS Inputs e Anexcellent user interface consisting of 14 LED Diagnostic Indicators e Two independent single pole double throw SPDT Relay Outputs that allow you to interface to door strikes magnetic locks and other third party devices for example alarm panels or lighting e Four Digital Inputs including two Door Open Sensor DOS and two Request to Exit RTE Inputs e Added ability to interface with Motor and Solenoid Locks e Connects to the PC using a standard Ethernet cable e A Firmware Upgrade Utility downloadable f
9. r Warranty details on www impro net Page 4 IXP20 NET TCP IP Up to 8 Door Controllers per System Controller RS485 gt DC IXP20 TOUCH Up to 8 Door Controllers per System Controller Figure 1 IXP20 System Overview SYSTEM Controller The IXP20 Controller is available as an IXP20 Touch Touch Screen Interface or an IXP20 Net Web Interface DOOR Controllers The following Door Controllers are compatible with the IXP20 System Each Door Controller is compatible with specific Readers Always select the correct Readers for the chosen Door Controller DOOR Readers Each Door Controller is compatible with specific Readers Please refer to your chosen Door Controller s Product Specification Catalogue for a full list of compatible Readers Page 5 This Product Specification Catalogue applies to the ImproX IXP20 System ISC910 1 0 GB 03 ISC911 5 0 GB 03 ISC920 0 0 GB 03 and ISC921 5 0 GB 03 The last two digits of the Impro stock code point to the issue status of the document or product IXP20 Controller Product Specification Catalogue LATEST ISSUE ISC353 0 0 GB 05 Issue 06 July 2011 IXP20Sys psc en 06 docx Page 6
10. rom Web to upgrade Firmware while installed on site without removal of the Controller e 3 Year Warranty on Hardware e Support for up to 18 Holidays e Daylight Savings Support e Support for up to 8 Tagholder Access Groups e Allows for Batch Loading of Tags e User configurable Tag loading Template e When used with a Keypad Reader System support includes Reason Codes Personal Access Codes PAC PIN codes e Stores all information locally on the Controller e Allows you to save the entire Database to the PC for backup and restore purposes e Offers the following Reports Access Report Status Report Audit Report Hours Worked Report e Supports 1 Anti passback APB Zone e The IXP20 Web UI allows export of CSV data from the Web browser e The IXP20 Web UI works with both Windows Internet Explorer 8 and above or alternatively Firefox 3 and above e The IXP20 Touch allows you to carry out registration of 125 kHz and 13 56 MHz Tags using the Controller s internal Reader e IXP20 Touch Controllers also include the Web UI ISC910 and ISC911 ImproX iTT Platform e Interfaces with the full range of ImproX 125 kHz Antenna Readers e Antenna Reader read capability using the following Tags Slim Tags Omega Tags Philips HITAG 1 Philips HITAG 2 and HID 125 kHz Tags CAUTION The IXP20 System does not support the use of HID 1346 Proxkey II Tags NOTE HID is a registered trademark of HID
11. s Up to 25 Up to 1 HID iCLASS Tags Up to 25 Up to 1 FeliCa Credit Card Tags Up to 25 Up to 1 MIFARE Credit Card Tags Up to 25 Up to 1 Physical Specifications Length 126 mm 5in Width 166 mm 7 in Height S mim 2 im Approximate Weight ISC910 302g 1102 ISC911 oo SO o I oZ ISC920 gt 314g 11 02 ISC921 Pe coe GiUlaOZ Cabinet Material ABS Plastic Colour Black Environmental Specifications Operating Temperature 25 C to 60 C 13 F to 140 F Storage Temperature 40 C to 80 C 40 F to 176 F 0 to 95 relative humidity at 40 C 104 F non condensing Humidity Range Approvals CE Approval EN8301 489 3 and EN301 489 1 FCC Approval Pending Dust amp Splash Resistance Designed to work in an indoor dry environment similar to IP40 The Controller is not sealed against water Drop Endurance 1 m 3 28 ft drop in packaging Electrical Specifications Improx iTT Platform Power Input Voltage 10 V DC to 30 V DC polarity sensitive Power Continued Power Requirements 1SC910 Input Voltage 12 V DC with no Antennas attached Input Voltage 24 V DC with no Antennas attached Input Voltage 12 V DC with Antennas attached Input Voltage 24 V DC with Antennas attached Current mA Power W 90 1 08 50 1 20 100 1 20 60 1 44 Power Requirements ISC911 Input Voltage 12 V DC with no Antennas attached Input Voltage 24 V DC with no Ante
Download Pdf Manuals
Related Search