1. Package Contents 3. Physical Introduction 2. Installation
Contents
1. PLANET Networking amp Communication Quick Installation Guide 300Mbps 802 11a n Wireless Outdoor AP 1 Package Contents Thank you for choosing PLANET WNAP 7320 Before installing the AP please verify the contents inside the package box WNAP 7320 Quick Guide PoE Injector amp Power Cord Mounting Tie x 2 CD ROM If there is any item missed or damaged please contact the seller immediately Rear Panel Description Mounting Design Pole Mount Holders L Mount Option Bottom Panel Description Port LAN Passive PoE WAN Router Mode Pin4 5 Pin 7 8 LAN Bridge Mode 2 Installation Precautions Users MUST use a proper and well installed surge arrestor and grounding kit with WNAP 7320 otherwise a random lightening could easily cause fatal damage to WNAP 7320 EMD Lightning DAMAGE IS NOT COVERED UNDER WARRANTY 2 Users MUST use the Power cord amp PoE Injector shipped in the box with the WNAP 7320 Use of other options will cause damage to the WNAP 7320 3 Physical Introduction Side Panel Description LED Indication Signal Indicator Wireless LED LAN Port LED WAN Port LED Power LED 4 Hardware Installation STEP 1 Push the latch in the bottom of WNAP 7320 to remove the sliding cover STEP 2 Plug the RJ 45 Ethernet cable into the PoE LAN Port of WNAP 7320 STEP 3 Take out the power cord and PoE injector plug the power cord into the DC port a2. use the Power cord amp PoE Injector shipped in the box with the WNAP 7320 Otherwise the product might be damaged Default IP Address 192 168 1 1 Default User name admin Default Password admin Default SSID default Now you can see the Web management UI of the WNAP 7320 You can use Easy Setup at the top of the screen to configure the WNAP 7320 WNAP 7320 _ 300Mbps 802 11a n Wireless Outdoor AP Router Further Information The above steps introduce simple installations and configurations for WNAP 7320 For further configurations of different operation modes please refer to the user s manual in the CD If you have further questions please contact the local dealer or distributor where you purchased this product 2011 E10530 000
3. nd plug the other side of the RJ 45 cable in the STEP 2 into the POE port of the PoE injector PoE Out Router Mode Internet Datailn n Poot Port 24V PoE Injector Ethernet Cable Ethernet Cable Data f PC Data Power STEP 4 Slide the cover back to seal the bottom of the WNAP 7320 to finish the installation 6 Web Login Connect the WNAP 7320 with your PC by an Ethernet cable plugging in LAN port of PoE injector in one side and in LAN port of PC in the other side Power on the WNAP 7320 by PoE from PoE injector 1 Assign a static IP address to your PC which should be in the same network segment with the WNAP 7320 As the default IP address of the WNAP 7320 is 192 168 1 1 you may choose from 192 168 1 2 to 192 168 1 254 Then click OK Open the web browser on your PC key in the IP address 192 168 1 1 of the WNAP 7320 in the address bar and then enter 3 The default User name and Password are both admin Enter them and then click OK 300Mbps 802 11a n Wireless Outdoor AP Router 5 Pole Mounting STEP 1 Place the straps through the slots on the back of the WNAP 7320 and then around the pole Tighten the straps to secure your WNAP 7320 IMPORTANT SAFETY PRECAUTIONS 1 LIVES MAY BE AT RISK Please be aware for the electric wires around and tighten the pole Carefully read the section OUTDOOR INSTALLATION WARNING in the manual before installation 2 Users MUST
Download Pdf Manuals
Related Search