(SAVE THESE INSTRUCTIONS)
Contents
1. G MRONEK ybe UyberRower 1 Power Switch Press the switch for 2 seconds to turn the UPS ON or OFF Alarm setting The audible alarm can be turned OFF or ON by quickly pressing the POWER button twice The default setting is for the Alarm On To turn the Alarm Off quickly press the power button twice You will hear two short beeps when the Alarm is turned off To turn the Alarm back on quickly press the power button twice You will hear a single short beep when the Alarm is turned on 2 Led Indicators This LED is illuminated when the UPS is working 3 Input Power Cord Connect to utility power 4 AC outlet The UPS provides outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes TECHNICAL SPECIFICATIONS BU600E BU1000E 1000 TROUBLESHOOTING Possible Cause Solution Recharge the battery by leaving the Batteries are not fully charged The UPS does not perform UPS plugged in expected runtime oe Contact CyberPower Systems Battery is slightly worn out Technical Support Capacity VA o Oeo ee Watt W Input 165 280Vac 50 Hz Voltage Range Nominal Frequency Output On Battery Output Voltage The unit is not connected to an AC The unit must be connected to a outlet 220 240V outlet AI EN OEL ON Contact CyberPower Systems The battery is worn out A Technical Support Contact CyberPower Systems Technical Support2. Simulated Sine Wave at 220Vac 5 On Battery Output Frequency 50 Hz 1 Overload Protection Breaker Fuse Mechanical problem Physical Dimensions H x W x D mm 91 5 x 158 x 240 110 5 x 190 x 290 Weight 3 8 kg 6 9 kg Battery Turn the UPS off and unplug at least one piece connected equipment Unplug the power cord of the UPS then Fuse is blown or breaker is tripped replace the blown fuse with a spare due to overload one or press the circuit breaker Knob Outlets do not provide power to Connect power cord then turn the UPS equipment on Make sure that your spare fuse meets the specification Allow the unit to recharge for at least 4 Batteries are discharged moaie Unit has been damaged by a surge or Contact CyberPower Systems spike Technical Support Sealed Maintenance Free Lead Acid Battery Typical Recharge Time RBP0043 x1 RBP0046 x2 8 Hours Warning Diagnostics Indicators Audible Alarms Environmental Power On Using Battery On Battery Low Battery Overload Fault Operating Temperature 0 C to 40 C 0 to 90 Operating Relative Humidity For more information visit www cpsww com Management All rights reserved Reproduction without permission is prohibited Auto Charger Yes Auto Restart Yes DEFINITIONS FOR ILLUMINATED LED INDICATORS 3 ys j z l Alarm Condition Off Normal Beep Twice Utility Failure The UPS is providing battery power to outlets Rapid
3. the on and off position 2 With the UPS unit off and unplugged connect the computer monitor and any externally powered data storage device Zip drive Jazz drive Tape drive etc into the battery power supplied outlets DO NOT plug a laser printer copier space heater vacuum paper shredder or other large electrical device into the battery power supplied outlets The power demands of these devices will overload and possibly damage the unit 3 Plug the UPS into a 2 pole 3 wire grounded receptacle wall outlet Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical demands e g air conditioner refrigerator copier etc Avoid using extension cords 4 Press the power switch to turn the unit on The power on indicator light will illuminate and the unit will beep 5 Ifan overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets Wait 10 seconds Make sure the circuit breaker fuse is normal and then turns the UPS on 6 To maintain optimal battery charge leave the UPS plugged into an AC outlet at all times 7 To store your UPS for an extended period cover it and store with the battery fully charged Recharge the battery every three months to ensure battery life BASIC OPERATION L EOC A MSSD
4. Cy berPower Reliability Quality Value BU600E BU1000E User s Manual K01 C000065 00 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate your UPS CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants See the specifications for the acceptable temperature and humidity range CAUTION To reduce the risk of overheating the UPS do not cover the UPS cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces CAUTION Do not attach non computer related items such as medical equipment life support equipment microwave ovens or vacuum cleaners to UPS CAUTION Do not plug the UPS input into its own output CAUTION Do not allow liquids or any foreign object to enter the UPS Do not place beverages or any other liquid containing vessels on or near the unit CAUTION In the event of an emergency press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS CAUTION Do not attach a power strip or surge suppressor to the UPS CAUTION Unplug the UPS prior to cleaning and do not us
5. Utility Failure The UPS is providing battery power The rapid beeps indicate Beeping the battery will run out of power shortly Constant Overload Occurs when connected equipment exceeds the rating of the unit Tone Turn the UPS off and unplug at least one piece of equipment from the UPS On Flash
6. e liquid or spray detergent CAUTION Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries CAUTION The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary CAUTION Internal battery voltage is 12Vdc Sealed lead acid 6 cell battery CAUTION When replacing the batteries use the same number and type of batteries CAUTION Do not dispose of batteries in a fire The battery may explode Do not open or mutilate the battery or batteries Released electrolyte is harmful to the skin and eyes INSTALLING YOUR UPS SYSTEM UNPACKING The box should contain the following 1 UPS Unit x1 2 Quick Start Guide x1 3 User Manual x1 OVERVIEW The BU600E BU1000E provides automatic voltage regulation for inconsistent utility power and provides battery backup during power outages The BU600E BU1000E ensures consistent power to your computer system HARDWARE INSTALLATION GUIDE 1 Your new UPS may be used immediately upon receipt However recharging the battery for at least 8 hours is recommended to ensure that the battery s maximum charge capacity is achieved Charge loss may occur during shipping and storage To recharge the battery simply leave the unit plugged into an AC outlet The unit will charge in both
Download Pdf Manuals
Related Search