Corner Mount Camera - Seco-Larm
Contents
1. a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no user serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other re2. SECO LARM Corner Mount Camera Manual EV 4606 N2SBQ shown 550 TV Lines ls Sony Super HAD Il Color CCD yY a ae 2 9mm Lens Features EV 4605 N2SQ EV 4606 N2SBQ a ee ee a 23mmLens 160 Viewing Angle O A N v 30 IR LEDs C i i SLI Kas CE Note Model numbers that end with Q or that have a round green Q sticker signify ROHS compliant products SECO LARM Corner Mount Camera Specifications EV 4605 N2SQ EV 4606 N2SBQ Type Corner Mount Camera CCD 1 3 Sony Super HAD II Color CCD Resolution Color 550 TV lines B W 590 TV lines Pickup elements 768x494 pixels Video output format NTSC 1 0Vp p composite video 75Q 2 1 Interlace Lens 2 3mm Viewing angle 160 0 1 lux F 1 4 0 1 lux F 1 4 LEDs OFF Minimum illumination S N ratio gt 48dB of IR LEDs Gamma correction Gain control CA Power source a Operating temperature 14 122 F 10 50 C Dimensions LxWxH 15 0z 430g Parts List 1 x Manual 1 x Camera cover 3 x Security screws 1 x Pigtail connector 1 x Camera 2 x Mounting screws 1 x Security wrench Dimensions k 711 190mm j y J N P eo00000 ooa0000 F onono 00000009 F 111 46 lt 42 3mm Note EV 4606 N2SBQ shown Both models have the same dimensions 2 SECO LARM U S A Inc Overview Mounting screw Note EV 4606 N2SBQ sho
3. ason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2010 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com wl PIKSRI Tel 800 662 0800 949 261 2999 E mail sales seco larm com mi EV 460x N2SxQ docx 4 SECO LARM U S A Inc
4. the two included mounting screws If the wall is made of dry wall brick or similar material it may be necessary to use screw anchors not included Attach the base cover using the included security wrench Do a final test of the video camera and monitor SECO LARM U S A Inc SECO LARM Corner Mount Camera Troubleshooting Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen is blank e Clean the lens using a soft clean cloth Une sefeenmage Isam e Check that the light source is adequate e Adjust the monitor s contrast knob The screen image has poor contrast Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted e Change the position of the camera The camera case is hot e Check that the correct power supply is in use IR LEDs do not turn on e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see
5. wn Security screw Before Starting 1 2 3 4 5 Please read this manual carefully and keep it for future reference Use the camera within given temperature and electrical limits Do not mount the camera where it is exposed to rain or other moisture or in humid or dusty places Do not point the camera at the sun Intense light could damage the camera even when not in use Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals Installation 1 Run a 12VDC power supply wire and a video cable with a male BNC connector through the wall at the corner where the camera is to be mounted Use the included security wrench to loosen the screws and remove the camera cover from the camera Connect the power supply and video cable Turn the monitor on and make sure the camera is sending the proper video signal Wire comes from bottom of camera Camera cover SECO LARM Corner Mount Camera Pigtail connector Female BNC connector Important Do not cut DC jack or BNC connector as warranty will be voided 6 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on Mount the camera against the corner using
Download Pdf Manuals
Related Search