USER MANUAL www.saeco.com/welcome Type
Contents
1. Green y Press the button to start dispensing hot water EJ Dispense water until the no water icon appears Note The manual rinse cycle can be stopped by pressing the De button E At the end of this operation fill the water tank again up to the MAX level Now the machine is ready to brew coffee The display on the left will be shown Note The automatic rinse self cleaning cycle starts when the machine has been in stand by mode or turned off for more than 15 minutes When you have not used the machine for 2 or more weeks you will also need to perform a manual rinse cycle At the end of the cycle you can brew a coffee C POP B Intenza Aroma System A ENGLISH 17 Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descal ing frequency and to install the INTENZA water filter for more details on the water filter see next chapter To measure the water hardness follow the steps below E Immerse the water hardness test strip supplied with the machine in YS water for 1 second Note The test strip can only be used for one single measurement FJ Wait for one minute EJ Check how many squares have changed colour to red and then refer to the table Note The numbers on the water hardness test strip correspond to the water hardness adjustment settings More precisely 1 1 very soft wa2. Saeco Miiunute USER MANUAL Type HD8762 HD8780 HD8862 HD8865 Read carefully before using the machine CE Register your product and get support at www saeco com welcome IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 8 9 Read all instructions Do not touch hot surfaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any control to off then re
3. dampened cloth 38 ENGLISH GX Make sure that the brew group is in the off position the two reference EK Gently pull down the lever until it is in contact with the brew group base and the two reference marks on the side of the brew group match Press the PUSH button firmly EE Make sure that the hook which locks the brew group is in the correct position If it is still in the downward position push it upward until it locks correctly into place marks must match If they do not match proceed as described in step 11 ENGLISH 39 EE Insert the coffee residues drawer into its seat and ensure that it is cor rectly in place Note If the coffee residues drawer is not correctly positioned the brew group may not fit into the machine EH Insert the brew group back into its seat until it locks into place without pressing the PUSH button E Insert the coffee grounds drawer with the drip tray back into the ma chine and close the service door 40 ENGLISH Monthly Cleaning of the Automatic Milk Frother Every month you need to perform a more thorough cleaning of the Auto matic Milk Frother using the Saeco Milk Circuit Cleaner The Saeco Milk Circuit Cleaner can be purchased separately For further details please refer to the maintenance products page in this user manual PN warning Danger of scalding Dispensing may be preceded by small jets of hot water E Make s
4. Water Filter When the INTENZA water filter needs to be replaced with a new one this icon is displayed E Replace the INTENZA water filter as described in the previous chap ter g FJ Press the button and scroll through the options by pressing the 5 button until this icon is displayed v gt EJ Select the RESET option Press the button to confirm Yellow EJ To exit press the dI button The machine shows this display and is ready to brew Green The machine is now programmed to manage a new INTENZA water filter heal Note If the INTENZA water filter is already installed and you want to remove but not replace it select the OFF option instead Yellow If there is no INTENZA water filter installed insert the small white filter previously removed into the water tank 22 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin blend and roast The machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market except for raw caramelized and flavoured coffee beans The machine automatically adjusts itself after brewing several cups of cof fee to
5. Water is sometimes drained auto matically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance The coffee grounds drawer has been emptied with the machine off The drip tray gets filled al though no water is drained The red ej icon is always displayed on the machine Coffee is not hot enough The cups are cold ENGLISH 65 Solutions Connect the machine to the electric network and turn the power button to the I position This is a normal behaviour of the machine The coffee grounds drawer must always be emptied with the machine on Wait until the icon is dis played before refitting the drawer Preheat the cups with hot water Temperature is not correctly set The machine circuit is clogged by limescale The hole of the steam hot water wand is clogged No hot water or steam is dispensed Coffee does not have enough The blend is unsuitable coffee is crema see note not freshly roasted or the grind is too coarse The machine takes a long time to warm up or the amount of water dispensed is too little The machine circuit is clogged by limescale The brew group cannot be removed The brew group is out of place Set the temperature as described in the Programming chapter Descale the machine Clean the hole of the steam wand using a pin Make sure that the machine is off and has cooled down before performing
6. at the other end of the power cord into a wall socket with suitable power voltage 12 ENGLISH DEMO MODE OH START Yellow Switch the power button to I The button flashes To turn on the machine simply press the button By keeping the button pressed for more than 8 seconds the machine enters the demo mode To exit the demo disconnect the power cord and turn the machine back on EE The control panel indicates that the circuit must be primed ENGLISH 13 USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time the following activities need to happen 1 You need to prime the circuit 2 The machine will perform an automatic rinse self cleaning cycle 3 you need to perform a manual rinse cycle Circuit Primin During this process fresh water flows through the internal circuit of the machine and the machine warms up This takes a few minutes EE Place a container under the steam wand START Yellow Pl Press the button to start the cycle The machine starts the auto matic priming of the circuit by dispensing some water through the steam wand EJ The bar under the icon shows the operation progress When the pro cess has been completed the machine stops dispensing automatically Yellow EJ The contro panel now shows the machine warm up icon Yellow 14 ENGLISH Automatic
7. fuse WARRANTY AND SERVICE Warranty For detailed information on your warranty and related conditions please read the warranty booklet supplied separately Service We want to ensure that you remain satisfied with your machine If you have not already done so please register your purchase at www saeco com welcome This will enable us to stay in contact with you and send you cleaning and descaling reminders If you need service or support please visit the Philips website at www saeco com support or contact the Philips Saeco hotline in your country The contact details can be found in the warranty booklet supplied sepa rately or at www saeco com support ENGLISH 69 ORDERING MAINTENANCE PRODUCTS For cleaning and descaling use Saeco maintenance products only You can purchase the products at the Philips online shop at www shop philips com service from your local dealer or at authorised service centres If you have any difficulties obtaining maintenance products for your ma chine please contact the Philips Saeco hotline in your country Contact details can be found in the warranty booklet packed separately or at Www saeco com support Overview of maintenance products Descaling solution CA6700 _INTENZA Water filter cartridge CA6702 Grease HD5061 70 ENGLISH Coffee Oil Remover CA6704 Milk Circuit Cleaner CA6705 Maintenance Kit CA6706 PHILIPS The manufacturer reserves the rig
8. in the warranty booklet packed separately or at www saeco com support 64 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could encoun ter with your machine If you are unable to solve the problem with the information below visit www saeco com support for a list of frequently asked questions or con tact the Philips Saeco hotline in your country Contact details can be found in the warranty booklet packed separately or at www saeco com support Machine actions Error Code 1 Coffee grinder blocked Error Code 3 4 The brew group is out of place Brew group blocked cannot be pulled out Error Code 5 Water circuit error Causes Coffee outlet duct clogged Air in the water circuit Solutions Thoroughly clean the coffee outlet duct as described in the Weekly Cleaning of the Brew Group chapter Close the service door Turn off and back on the machine The brew group automatically returns to the initial position Remove and put back the water tank a few times making sure it is properly reinserted Check that the water tank compart ment is clean If the Intenza filter is installed remove it Turn off and back on the machine The machine circuit is clogged by limescale Descale the machine Machine actions Causes The machine does not turn The machine is not connected to on the electric network or the power button is in the O position
9. pour out of the coffee dispensing spout Fal Coffee brewing stops automatically when the set level is reached However it is possible to stop coffee brewing early by pressing the button ENGLISH 27 Brewing Espresso and Coffee Using Pre Ground Coffee This function allows you to use pre ground coffee With the pre ground coffee function you can only brew one coffee at a time El Press the button to select the pre ground coffee function Green Lift the pre ground coffee compartment lid and add one level measur ing scoop of pre ground coffee Use only the measuring scoop supplied with the machine Then close the pre ground coffee compartment lid PN warning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damage to the ma chine Such damage will not be covered by warranty EJ Press the button for an espresso or the 2 button for a coffee MEMO The brewing cycle starts E After the prebrewing cycle coffee begins to pour out of the coffee dispensing spout E Coffee brewing stops automatically when the set level is reached However it is possible to stop coffee brewing early by pressing the button After brewing the machine returns to the main menu Repeat the steps described above to brew more coffees using pre ground coffee See an imu Note If no pre ground coffee is poured into the pre g
10. select steam Ef This icon is displayed during the preheating time required by the machine TUF H This icon will be displayed during the dispensing phase Dispense water from the Automatic Milk Frother until clear water flows out Press the 2 button to stop dispensing Green Green Fl Clean the suction tube with a damp cloth 36 ENGLISH Weekly Cleaning of the Machine El Clean the seat of the drip tray Weekly Cleaning of the Brew Grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week El Turn off the machine by pressing the I button and unplug the power cord Remove the drip tray and coffee grounds drawer EJ Open the service door ENGLISH 37 EZ To remove the brew group press the PUSH button and pull it by the handle Pull it out horizontally without turning it E Thoroughly clean the coffee outlet duct with the special cleaning tool provided with the machine or with a spoon handle Make sure that the cleaning tool is inserted as shown in the figure Kal Remove the coffee residues drawer and wash it thoroughly Thoroughly wash the brew group with fresh lukewarm water and care fully clean the upper filter a Caution Do not use detergent or soap to clean the brew group EJ Let the brew group air dry thoroughly EJ Thoroughly clean the inside of the machine using a soft
11. water quality E Remove the small white filter from the water tank and store it in a dry place Remove the INTENZA water filter from its packaging immerse it ver tically with the opening positioned upwards in cold water and gently press the sides so as to let the air bubbles out EJ Set the INTENZA water filter according to the measurements per formed see previous chapter and indicated on the base of the filter A soft water equals 1 or 2 on the test strip B hard water standard equals 3 on the test strip C very hard water equals 4 on the test strip 20 ENGLISH Yellow Yellow Green QZ Put the INTENZA water filter into the empty water tank Press it down until it cannot move any further E Fill the water tank with fresh water and put it into the machine Fl Dispense all the water in the water tank by using the hot water func tion see the Dispensing Hot Water chapter Fill the water tank again EJ Press the button and scroll the options by pressing the button until this display is shown EJ Press the button to select ON and press the button to con firm GI To exit press the eIl button The machine shows this display and is ready to brew The machine is now programmed to inform the user of the need to replace the INTENZA water filter ENGLISH 21 Replacing the INTENZA
12. ING MAINTENANCE PRODUCTG s ccssssssssssssssesssessesssnsessessassosesesenees 69 4 ENGLISH IMPORTANT Safety Instructions This machine is equipped with safety devices Nevertheless read and follow the safety instructions carefully and only use the machine properly as described in these instructions to avoid accidental injury or damage due to improper use of the machine Keep this user manual for future reference yN The term WARNING and this icon warn against possible severe injuries danger to life and or damage to the machine KA The term CAUTION and this icon warn against slight injuries and or damage to the machine Warnings e Connect the machine to a wall socket with a voltage match ing the technical specifications of the machine e Connect the machine to an earthed wall socket Do not let the power cord hang over the edge of a table or counter or touch hot surfaces e Never immerse the machine the mains plug or power cord in water Danger of electrical shock e Do not pour liquids on the power cord connector e Never direct the hot water jet towards body parts Danger of burning e Do not touch hot surfaces Use handles and knobs e After switching off the machine by pressing the power but ton on the back of the machine remove the mains plug from the wall socket ifa malfunction occurs ENGLISH 5 ifthe machine will not be used for a long time before cleaning the machine Pul
13. Rinse Self Cleaning Cycle STOP Yellow Green When warm up has been completed the machine automatically performs a rinse self cleaning cycle of the internal circuits with fresh water This takes less than a minute H Place a container under the coffee dispensing spout to catch the small amount of water which will be dispensed a The machine shows this display Wait for the cycle to finish automati cally k Note You can stop dispensing by pressing the 2 button When the operations described above have been completed the ma chine shows this display You can now perform the manual rinse cycle ENGLISH 15 Manual Rinse Cycle During this process the coffee brewing cycle is activated and fresh water flows through the water circuit This takes a few minutes El Place a container under the coffee dispensing spout Check that the machine shows this display J EJ Select the pre ground coffee brewing function by pressing the sia F button The machine shows this display E Note Do not add any pre ground coffee into the compartment EJ Press the 2 button The machine starts dispensing water E When dispensing has finished empty the container Repeat the opera tions from step 1 to step 4 twice then continue with step 6 K Place a container under the steam wand 16 ENGLISH CAPPUCCINO dib Red
14. Strength Adjusting the Coffee Dispensing Spout Adjusting the Coffee Length BREWING ESPRESSO AND COFFEE Brewing Espresso and Coffee Using Coffee Beans Brewing Espresso and Coffee Using Pre Ground Coffee FROTHING MILK BREWING CAPPUCCINO Frothing milk Brewing a Cappuccino HOT WATER DISPENSING CLEANING AND MAINTENANCE Daily Cleaning of the Machine Daily Cleaning of the Water Tank Daily Cleaning of the Automatic Milk Frother Weekly Cleaning of the Machine Weekly Cleaning of the Brew Group Monthly Cleaning of the Automatic Milk Frother Monthly Lubrication of the Brew Group Monthly Cleaning of the Brew Group with Coffee Oil Remover Monthly Cleaning of the Coffee Bean Hopper DESCALING cccccssssssssssssssssssesesesssesecssecscesecesssesscesssesssesssesosesssesoseseseronesoneses ACCIDENTAL INTERRUPTION OF THE DESCALING CYCLE sssssssssssssessessessosees 56 PROGRAMMING 000006 57 The following settings can be adjusted How to Program the Machine MEANING OF THE DISPLAY ICONS TROUBLESHOOTING sccsssssssessssssossssssssossssssessssessosssessesesssessesssesessesesensesees 64 ENERGY SAVING Stand by TECHNICAL SPECIFICATIONS scsssossssssssosssssssssssessosssssesesssessesssesesseseseneesees 68 WARRANTY AND SERVICE Warranty Service ORDER
15. The values that have been changed but not con firmed will not be saved 60 ENGLISH MEANING OF THE DISPLAY ICONS This machine is equipped with a colour coded system to make the user s understanding of the display signals easier The icons are colour coded according to the traffic light principle Ready Signals Green Colour 2 Lp w 1P th r T STOP STOP fll j Syg A j Sy a f A p oe 7 a The machine is ready to brew products The machine is ready to brew pre ground coffee Hot water dispensing Steam dispensing The machine is brewing one cup of espresso The machine is brewing one cup of coffee The machine is brewing two cups of espresso The machine is brewing two cups of coffee The machine is programming the amount of espresso to be brewed ENGLISH 61 Ready Signals Green Colour The machine is programming the amount of coffee to be brewed Espresso brewing using pre ground coffee in progress Coffee brewing using pre ground coffee in progress The machine is warming up to dispense beverages 62 ENGLISH Z LP s 5 y B D amp E Oe Y A START CRY START Esc T gt 4 via CALC CLEAN Warning Signals Yellow Colour The machine is warming up The machine is performing the rinse cycle Wait until the machine has com pleted the
16. calding Dispensing may be preceded by small jets of hot water The steam wand and the chrome cover may reach high tem peratures Before dispensing hot water make sure that the machine is ready to use and the water tank is filled Green l E Remove the Automatic Milk Frother from the steam wand 32 ENGLISH STOP a Q Green Green Place a container under the steam wand y EJ Press the button to start dispensing hot water EZ This icon is displayed during the preheating time required by the machine E Pour the desired amount of hot water To stop dispensing hot water press the 2 button ENGLISH 33 CLEANING AND MAINTENANCE Daily Cleaning of the Machine BEB caution Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine Your machine is continuously exposed to moisture coffee and limescale The activities you need to perform and their frequency are described in detail in this chapter Not doing this will ultimately make your machine stop working properly This repair is NOT covered by your warranty mall Note Use a soft dampened cloth to clean the machine Only the cup holder grill can be washed in the dishwasher Any other components must be washed with lukewarm water Do not immerse the machine in water Do not use alcohol solvents and or abrasive objects to clean
17. cycle The machine needs the INTENZA water filter to be replaced The brew group is being reset due to machine reset Refill the coffee bean hopper with coffee beans Prime the circuit You need to descale the machine Press the 2 button to start the descaling process Follow the steps described in the Descaling chapter of this manual If you want to descale the machine later press the diiy button to continue using the machine Please note that not descaling your machine will ultimately make it stop working properly In this case repair is NOT covered under your warranty ENGLISH 63 Warning Signals Red Colour oo j i Completely insert the drip tray with the coffee grounds drawer into the ma chine and close the service door Fill the coffee bean hopper The brew group must be inserted into the machine Empty the coffee grounds drawer Wait 5 seconds before reinserting it Fill the water tank The machine is out of order The error code is displayed in the right bottom corner For error codes 1 3 4 5 please refer to the Troubleshooting chap ter For any other error codes follow the instructions below Turn off the machine Turn it back on after 30 seconds Try this 2 or 3 times If the machine does not start contact the Philips SAECO hotline in your coun try and quote the error code shown on the display Contact details can be found
18. djust the amount of coffee to Peme be ground according to your personal taste You can also select the pre ground coffee function COFFEE J Note Selection must be made prior to selecting coffee You can choose from 5 options by pressing the g amp button Each time the button is pressed the aroma changes by one degree according to the selected amount 2OO extra mild aroma O2OD mild aroma MULO medium aroma MUUL strong aroma 00000 extra strong aroma we pre ground coffee Green Green 24 ENGLISH Adjusting the Coffee Dispensing Spout The height of the coffee dispensing spout can be adjusted to better fit the size of the cups that you wish to use Move the coffee dispensing spout up or down with your fingers to adjust its height as shown in the figure The recommended positions are For the use of small cups For the use of large cups Two cups can also be placed under the coffee dispensing spout to brew two cups of espresso or coffee at the same time Adjusting the Coffee Length Green Green Green ENGLISH 25 The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups Each time the 2 or DZ button is pressed the machine brews a pre set amount of coffee Each button may be individually programmed for a specific brew setting Ef Place a cup under the coffee di
19. e collection system for electrical and electronic products Follow local regulations and do not dispose of the product as household waste Appropriate disposal of old products helps prevent negative consequences for the environment and human health INSTALLATION Product Overview ENGLISH 9 General Description Ey MR NES 20 21 22 23 24 25 26 27 28 29 30 31 32 34 Grinder adjustment knob Coffee bean hopper Pre ground coffee compartment Water tank Lid Coffee bean hopper lid Control panel Coffee dispensing spout Full drip tray indicator Cup holder grill Drip tray Coffee grounds drawer Brew group Service door Grease for brew group optional Power cord Automatic Milk Frother Suction tube for Automatic Milk Frother Coffee grinder adjustment key Pre ground coffee measuring scoop Power cord socket Power button Water hardness test strip Cleaning brush optional ON OFF button Espresso brew button Coffee brew button Aroma Pre ground coffee button Steam button Hot water button Menu button Descaling solution to be purchased separately Rubber fitting Coffee residues drawer Chrome cover 10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Machine Installati
20. e thoroughly Monthly Cleaning of the Coffee Bean Hopper Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil Then refill it with coffee beans 50 ENGLISH DESCALING When the CALC CLEAN icon is displayed you need to descale the machine The descaling cycle takes approx 30 minutes BEB caution Not doing this will ultimately make your machine stop working properly In this case repair is NOT covered by warranty WN warning Use the Saeco descaling solution only Its formula has been designed to ensure better machine performance The use of other products may damage the machine and leave residues in the water Yellow CALC CLEAN The Saeco descaling solution can be purchased separately For further details please refer to the maintenance products page in this user manual WN warning Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end Never use vinegar as a descaling solution PHILIPS _ Saeco Note Do not remove the brew group during the descaling process To perform the descaling cycle follow the steps below Before descaling E Empty the drip tray and the coffee grounds drawer Yellow ENGLISH 51 Remove the Automatic Milk Frother from the steam hot water wand EJ Press the amp button memo Note If you press the 2 button b
21. emove the chrome cover with the rubber fitting from the steam wand Remove the rubber fitting from the chrome cover ENGLISH 43 GES Remove the suction tube EE Press the sides and disassemblel the Automatic Milk Frother as shown in the figure Remove the rubber lid as shown in the figure Wash all the components with lukewarm water Reassemble the lid making sure that you press it in the middle to have it correctly inserted 44 ENGLISH Reassemble the Automatic Milk Frother making sure it is correctly inserted Install the suction tube Insert the rubber fitting into the chrome cover Reinsert them back onto the steam wand Eg Caution The tube could be hot if the machine has recently been used Be care ful Do not insert the rubber fitting beyond the position shown In this case the Automatic Milk Frother would not work correctly as it would not be able to draw up milk ENGLISH 45 Insert the Automatic Milk Frother in the rubber fitting BE Make sure that it is positioned correctly If you cannot insert it rotate the chrome cover The Automatic Milk Frother is assembled correctly when the tooth fits into the slot 46 ENGLISH Monthly Lubrication of the Brew Grou Lubricate the brew group after approximately 500 cups of coffee or once a month The grease to lubricate the brew group can be purchased separately For further details please refer to the maintenance prod
22. es to select the pre ground cof fee function without adding ground coffee to the compartment Green E Press the 2 button to start the coffee brewing cycle Fl wait until the machine has dispensed half a cup of water Switch the power button on the back of the machine to 0 EJ Let the solution take effect for about 15 minutes Make sure you dis card the dispensed water EJ Switch the power button on the back of the machine to I To turn on the machine press the Y button Wait until the end of the automatic rinse cycle E Remove the drip tray and the coffee grounds drawer and open the service door Remove the brew group Green ENGLISH 49 EE Wash the brew group thoroughly with fresh water After rinsing the brew group insert it back into its seat until it locks into place see the Weekly Cleaning of the Brew Group chapter Insert the drip tray and the coffee grounds drawer Close the service door GE Press the ere button to select the pre ground coffee function without adding any pre ground coffee into the compartment EE Press the button to start the coffee brewing cycle IE Repeat steps 13 to 14 twice Make sure you discard the dispensed water E To clean the drip tray place a Coffee Oil Remover tablet inside and fill it 2 3rds full with hot water Let the cleaning solution take effect for about 30 minutes then rins
23. ft water 2 soft water 3 hard water 4 very hard water For more details please see the Measuring and Programming Water Hard ness chapter INTENZA Water Filter This function allows you to manage the INTENZA water filter For more details see the chapter related to filter handling Descaling Cycle This function allows you to run the descaling cycle 58 ENGLISH Factory Settings This function allows you to reset all factory values Yellow How to Program the Machine In this example it is shown how to program the display contrast Proceed in the same way to program the other functions The programming menu can only be accessed when the machine is on and shows this display Green El Press the button to access programming E The main screen will be displayed Yellow EJ Press the button to scroll the options until the display contrast function is shown CAPPUCCINI CAPPUCCINO Cili Yellow ENGLISH 59 MEMO the function u Pr uM n El Press the and buttons to increase or decrease the value of E Once the value has been changed the OK message appears Press the button to confirm the change Fal Press the cll y button to exit programming i Note The machine automatically exits programming mode if no button is pressed for 3 minutes
24. ht to make changes without prior notice www saeco com welcome 421946014181 Rev 0O del 30 12 14
25. is positioned correctly If you cannot insert it rotate the chrome cover The Automatic Milk Frother is assembled correctly when the tooth fits into the slot Ql Insert the suction tube into the milk container BEB caution For hygienic reasons make sure that the outer surface of the suction tube is clean 30 ENGLISH STOP cll Green Green Place a cup under the Automatic Milk Frother EJ Press the cll y button to start frothing milk EJ This icon is displayed during the preheating time required by the machine E When this icon is displayed the machine dispenses frothed milk directly in the cup EE Press the button to stop dispensing It will take a few seconds before the machine stops frothing milk com pletely inal Note Milk frothing stops after 3 minutes If you need more press the dI y again After use store the suction tube as shown in the figure ENGLISH 31 BEB caution After frothing milk a small quantity of hot water must be dispensed into a container See the Daily cleaning of the Automatic Milk Frother chapter for detailed cleaning instructions Note It is possible to brew an espresso or dispense hot water straight after froth ing milk Brewing a Cappuccino To prepare a cappuccino place a cup of frothed milk under the coffee dispensing spout and brew an espresso HOT WATER DISPENSING WN warning Danger of s
26. l on the mains plug not on the power cord Do not touch the mains plug with wet hands Do not use the machine if the mains plug the power cord or the machine itself is damaged Do not make any modifications to the machine or its power cord Only have repairs carried out by a service centre au thorised by Philips to avoid any hazard The machine should not be used by children younger than 8 years old The machine can be used by children of 8 years and upwards if they have previously been instructed on the correct use of the machine and made aware of the associated dangers or if they are supervised by an adult Cleaning and maintenance should not be carried out by children unless they are more than 8 years old and super vised by an adult Keep the machine and its power cord out of reach of chil dren under 8 years old The machine may be used by persons with reduced physical sensory or mental capabilities or lacking sufficient experi ence and or skills if they have previously been instructed on the correct use of the machine and made aware of the associated dangers or if they are supervised by an adult Children should be supervised to ensure that they do not play with the machine Never insert fingers or other objects into the coffee grinder 6 ENGLISH Cautions The machine is for household use only It is not intended for use in environments such as canteens staff kitchens of shops offices factories or other wo
27. le you must complete it till the very end without turning off the machine If the descaling process is accidentally interrupted power failure or ac cidental disconnection of the power cord follow the steps below E Make sure that the power button is on EJ Press the button to turn on the machine EJ If the cycle was interrupted during the descaling phase it will be cane resumed from step 8 of the Descaling chapter Press the 2 button yA CEAN to restart the cycle Yellow EJ If the cycle was interrupted during the rinse phase it will be resumed from step 13 of the Descaling chapter Press the button to restart the cycle MEMO Yellow ENGLISH 57 PROGRAMMING You can customise the machine s functions via the programming menu The following settings can be adjusted TALC CLEAN gt Yellow Yellow Yellow Yellow Yellow Yellow Coffee Temperature This function allows you to adjust the coffee brewing temperature Timer stand by This function allows you to adjust the time taken for the machine to go into stand by mode after the last brewing Contrast This function allows you to adjust the contrast of the display to better view the messages Water Hardness This function allows you to adjust the water hardness settings according to the area where you live 1 very so
28. led In this case wait until the machine performs a self adjusting operation as described in the Saeco Adapting System chapter ENGLISH 67 ENERGY SAVING Stand b The Saeco fully automatic espresso coffee machine is designed for energy saving as proven by the Class A energy label After 15 minutes of inactivity the machine turns off automatically unless a different stand by time has been programmed If a product has been brewed the machine performs a rinse cycle In stand by mode the energy consumption is below 1Wh To turn on the machine press the I button if the power button on the back of the machine is set to I If the boiler is cold the machine performs a rinse cycle 68 ENGLISH TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power Rating Power Supply See data plate on the inside of the service door Housing material Thermoplastic material Size w x hx d Weight 215 x 330 x 429 mm 6 7 kg Power cord length 800 1200 mm Control panel Front panel Automatic Milk Frother Special for cappuccino Cup size Up to 152 mm Water tank 1 8 litres Removable type Coffee bean hopper capacity 250g Coffee grounds drawer capacity 15 Pump pressure 15 bar Boiler Stainless steel type Safety devices Thermal
29. might occur when the ma chine is automatically adjusting the dose Clean the coffee dispensing spout Brew a few cups of coffee as described in the Saeco Adapting System chapter The ceramic coffee grinder is set to a coarse grind The coffee grind is too fine Adjust the ceramic coffee grinder to a finer setting see the Adjust ing the Ceramic Coffee Grinder chapter Change coffee blend or adjust grinding as explained in the Adjust ing the Ceramic Coffee Grinder chapter The circuit is not primed Prime the circuit see the Using the Machine for the First Time chapter The brew group is dirty Coffee leaks out of the coffee The coffee dispensing spout is dispensing spout Milk does not froth Frothed milk is too cold clogged The Automatic Milk Frother is in serted too deep No milk is being suctioned The cups are cold The machine is indemo mode The y button was pressed and held for more than 8 seconds Note Clean the brew group see the Weekly Cleaning of the Brew Group chapter Clean the coffee dispensing spout and its holes Leave the Automatic Milk Frother to cool down Move it slightly down wards Reposition it in its correct seat Preheat the cups with hot water Disconnect the power cord and turn the machine back on These problems can be considered normal if the coffee blend has been changed or if the machine has just been instal
30. move plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use Ifa long detachable power supply cord
31. o start the rinse cycle Note The rinse cycle may be paused by pressing the button To resume the cycle press the button again This allows you to empty the container or MEMO to leave the machine unattended for a short time Yellow 54 ENGLISH CALC CLEAN Red EE When the amount of water needed for the rinse cycle has been com pletely dispensed this icon is displayed Press the cy button to quit the descaling cycle had not filled up the water tank to MAX level the machine might require another rinse cycle Refill the water tank and put it back into the machine Repeat from step 13 IE The machine warms up and performs the automatic rinse cycle Re move and empty the container Empty the drip tray and place it back EJ Remove the small white filter and place the INTENZA water filter into the water tank if it was installed Put back the Automatic Milk Frother ENGLISH 55 EE Make sure that it is positioned correctly If you cannot insert it rotate the chrome cover The Automatic Milk Frother is assembled correctly when the tooth fits into the slot I Clean the brew group For more details please see the Weekly Clean ing of the Brew Group chapter The machine is ready to brew coffee A j Z r L 56 ENGLISH ACCIDENTAL INTERRUPTION OF THE DESCALING CYCLE Once you have started the descaling cyc
32. on E Remove the machine from the packaging FJ For best use it is recommended to e Choose a safe level surface where there will be no danger of over turning the machine or being injured Choose a location that is sufficiently well lit clean and near an eas ily reachable socket Allow for a minimum distance from the sides of the machine as lt H shown in the figure 4 7 6inches 150 mm K 6inches if sa a EJ Open the water tank lid EJ Remove the water tank by using the handle ENGLISH 11 E Rinse the water tank with fresh water KA Fill the water tank with fresh water up to the MAX level and reinsert it into the machine Make sure it is fully inserted BEB caution Never fill the water tank with warm hot sparkling water or any other liquid as this may cause damage to the water tank and the machine Lift the coffee bean hopper lid EJ Slowly pour the coffee beans into the coffee bean hopper Note Do not pour too many coffee beans into the coffee bean hopper as this will reduce the grinding performance of the machine Ei caution Only coffee beans must be put into the coffee bean hopper If ground coffee instant coffee caramelized coffee raw coffee beans or any other substance is put in the coffee bean hopper it may damage the machine EJ Put the lid back on the coffee bean hopper E Insert the plug into the socket located on the back of the machine EK Insert the plug
33. optimize coffee extraction Adjusting the Ceramic Coffee Grinder Ceramic coffee grinders always guarantee accurate and perfect grinding and coarseness for every coffee speciality This technology provides full aroma preservation delivering a truly Italian taste in every cup PN warning The ceramic coffee grinder contains moving parts that may be danger ous Do not insert fingers or other objects Only adjust the ceramic coffee grinder using the grinder adjustment key You can adjust the ceramic grinders to set the coffee grinding to your personal taste PN warning You can only adjust the coffee grinder settings when the machine is grinding coffee beans El Place a cup under the coffee dispensing spout Press the button to brew an espresso MEMO ENGLISH 23 While the machine grinds coffee press and turn the grinder adjust ment knob placed inside the coffee bean hopper one notch at a time Use the special coffee grinder adjustment key supplied You will taste the difference after brewing 2 3 cups of coffee EJ The reference marks inside the coffee bean hopper indicate the grind setting There are 5 different grind settings to choose from from posi tion 1 for coarse grind lighter taste to position 2 e for fine grind stronger taste If coffee is watery or is brewed slowly change the coffee grinder settings Adjusting the Aroma Coffee Strength Choose your favourite coffee blend and a
34. or extension cord is used 1 The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Congratulations on your purchase of a Saeco Minuto Auto matic Milk Frother fully automatic coffee machine To fully benefit from the support that Saeco offers please register your product at www saeco com welcome The machine is made for preparing espresso coffee using whole coffee beans and for dispensing steam and hot water In this user manual you will find all the information you need to install use clean and descale your machine ENGLISH 3 CONTENTS Electromagnetic Fields Disposal INSTALLATION Product Overview General Description PREPARING FOR USE Machine Packaging Machine Installation USING THE MACHINE FOR THE FIRST TIME Circuit Priming ssssesesesssccccceeseeeenee Automatic Rinse Self Cleaning Cycle Manual Rinse Cycle Measuring and Programming INTENZA Water Filter Installation Replacing the INTENZA Water Filter ADJUSTMENTS Saeco Adapting System Adjusting the Ceramic Coffee Grinder Adjusting the Aroma Coffee
35. rk environments Always put the machine on a flat and stable surface Do not place the machine on hot surfaces directly next to a hot oven heater units or similar sources of heat Only put roasted coffee beans into the coffee bean hopper If ground coffee instant coffee raw coffee or any other substance is put in the coffee bean hopper it may damage the machine Let the machine cool down before inserting or removing any parts The heating surfaces may retain residual heat after use Never use warm or hot water to fill the water tank Use only cold non sparkling drinking water Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water Descale your machine regularly Not doing this will make your appliance stop working properly In this case repair is not covered under your warranty Do not keep the machine at temperature below 0 C Resi due water in the heating system may freeze and cause damage Do not leave water in the water tank if the machine is not used over a long period of time The water can get contami nated Use fresh water every time you use the machine ENGLISH 7 Electromagnetic Fields This appliance complies with all the applicable standards and regulations relating to the exposure to electromagnetic fields Disposal This symbol on a product indicates that the product is covered by EU Directive 2012 19 EU Please inform yourself about the local separat
36. round coffee compart ment only water will be dispensed If the dose is excessive or 2 or more scoops of pre ground coffee are added the machine will not brew the product and any ground coffee will be discharged into the coffee grounds drawer 28 ENGLISH Green FROTHING MILK BREWING CAPPUCCINO Frothing milk FN warning Danger of scalding Dispensing may be preceded by small jets of hot water When steam is used the steam wand and the chrome cover may reach high temperatures Never touch them with bare hands The Automatic Milk Frother must be handled only as shown in the figure EJ Fill 1 3 of a container with cold milk Note When preparing your cappuccino use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results Whole milk or skimmed milk may be used depending on individual taste Note When you plan to froth milk right after turning on the machine or after brewing a coffee any water still in the circuit may need to be dispensed first To do this press the c l y button to dispense steam for a few seconds Thereafter press the button to stop dispensing Then continue with step 2 FJ Before frothing milk make sure that the machine is ready to use and the water tank is filled ENGLISH 29 EJ Insert the suction tube into the Automatic Milk Frother l D E insert the Automatic Milk Frother into the steam wand seat E Make sure that it
37. spensing spout Keep the button pressed until the MEMO icon appears on the display to program an espresso or do the same with the button to program a coffee Then release the button The machine is in program ming mode and starts brewing the selected product EJ Press the A button as soon as the desired amount of espresso or cof fee is reached The previously selected 2 or 2 button is now programmed each time MEMO MEMO it is pressed the machine will brew the same amount of espresso or coffee that was just programmed 26 ENGLISH BREWING ESPRESSO AND COFFEE Green Green Before brewing coffee make sure that there are no warnings shown on the control panel and that the water tank and coffee bean hopper are filled Brewing Espresso and Coffee Using Coffee Beans E Place 1 or 2 cups under the coffee dispensing spout un FA To brew an espresso or a coffee press the button to select the desired aroma EJ Press the button for an espresso or the 2 button for a coffee EJ To brew 2 cups of espresso or coffee press the desired button twice consecutively This icon will be displayed Note In this operating mode the machine automatically grinds and doses the correct amount of coffee Brewing two espressos or two coffee requires two grinding and brewing cycles automatically carried out by the ma chine H After the prebrewing cycle coffee begins to
38. ter 2 2 soft water 3 3 hard water 4 4 very hard water The letters correspond to the references that are located at the base of the INTENZA water filter see next chapter Dn Cc E U N n n v C me S E S i g v x e 1 18 ENGLISH Yellow Yellow Green os El Press the button and scroll through the options by pressing the button until this icon is displayed Note z The machine is supplied with a standard water hardness setting suitable for most types of water H Press the 2 button to increase the value and the z button to decrease the value al Press the button to confirm the setting Press the dI y button to exit the programming MENU The machine shows this display and is ready to brew ENGLISH 19 INTENZA Water Filter Installation We recommend you to install the INTENZA water filter as this prevents limescale build up in your machine and preserves a more intense aroma of your coffee The INTENZA water filter can be purchased separately For further de tails please refer to the maintenance products page in this user manual Water is a crucial part of every coffee so it is very important to always have it professionally filtered Using the INTENZA water filter will prevent mineral deposits from building up and improve your
39. the machine Donot dry the machine and or its components using a microwave and or standard oven E Empty and clean the coffee grounds drawer and the drip tray daily with the machine turned on Other maintenance operations can only be carried out when the machine is turned off and unplugged EJ Remove the coffee grounds drawer and empty it EJ Empty and clean the drip tray 34 ENGLISH E Insert the coffee grounds drawer back into the drip tray and place the drip tray back into the machine imal Note Empty and wash the drip tray also when the full drip tray indicator is raised Daily Cleaning of the Water Tank EE Remove the small white filter or the INTENZA water filter if in stalled from the water tank and wash it with fresh water Put the small white filter or the INTENZA water filter if installed back in its housing by gently pressing and turning it at the same time ENGLISH 35 Daily Cleaning of the Automatic Milk Frother For hygienic reasons and to ensure a perfect milk froth consistency it is important that the Automatic Milk Frother be cleaned after each use PN warning Danger of scalding Dispensing may be preceded by small jets of hot water After each milk frothing you always need to El Insert the suction tube into a container filled with fresh water Place an empty container under the Automatic Milk Frother EJPress the Ii button to
40. this operation Change coffee blend or adjust the grind setting as explained in the Adjusting the Ceramic Coffee Grinder chapter Descale the machine Turn on the machine Close the ser vice door The brew group automati cally returns to the initial position The coffee grounds drawer is inserted The brew group cannot be inserted The brew group is not in the off position The gearmotor is not in the correct position Remove the coffee grounds drawer before removing the brew group Make sure that the brew group in the off position as described in the Weekly Cleaning of the Brew Group chapter Insert the drip tray and the coffee grounds drawer Close the service door Turn on the machine without inserting the brew group The gearmotor moves back to the correct position Turn off the machine and reinsert the brew group as described in the Weekly Cleaning of the Brew Group chapter 66 ENGLISH Machine actions The machine grinds coffee beans but no coffee comes out see note Coffee is too weak see note Coffee is brewed slowly see note Causes The brew group is dirty Solutions Clean the brew group see the Weekly Cleaning of the Brew Group chapter This might occur when the ma chine is automatically adjusting the dose Brew a few cups of coffee as described in the Saeco Adapting System chapter The coffee dispensing spout is dirty This
41. ucts page in this user manual BEB caution Before lubricating the brew group clean it with fresh water and let it dry as described in the Weekly Cleaning of the Brew Group chapter E Apply the grease evenly on both side guides Also lubricate the shaft ENGLISH 47 EJ Insert the brew group into its seat until it locks into place see the Weekly Cleaning of the Brew Group chapter E Close the service door and insert the drip tray and coffee grounds drawer Monthly Cleaning of the Brew Group with Coffee Oil Remover Besides weekly cleaning we recommend performing a cleaning cycle with Coffee Oil Remover after approximately 500 cups of coffee or once a month This operation completes the maintenance process for the brew group You can purchase the Coffee Oil Remover separately For further details please refer to the maintenance products page in this user manual 1 caution The Coffee Oil Remover tablets are to be used for cleaning only and do not have a descaling function For the descaling procedure use the Saeco descaling solution and follow the procedure described in the Descaling chapter E Place a container under the coffee dispensing spout Make sure the water tank is filled with fresh water up to the MAX level 48 ENGLISH EJ Put a Coffee Oil Remover tablet in the pre ground coffee compart ment EJ Press the ees button one or more tim
42. ure that the Automatic Milk Frother is correctly installed Pour the milk circuit cleaner into a container Add litre of lukewarm water and wait for the product to dissolve completely EJ Insert the suction tube into the container EJ Place a large container 1 5 I under the Automatic Milk Frother EJ Press the dI button to dispense steam Fl This icon is displayed during the preheating time required by the machine Green STOP dli Green Green ENGLISH 41 This icon will be displayed during dispensing When the solution has been completely dispensed press the button to stop dispensing rod PN warning Never drink the solution dispensed during this step EJ Rinse the container thoroughly and fill it with litre of fresh water to be used for the rinse cycle EJ insert the suction tube into the container E Empty the container and place it back under the Automatic Milk Frother EE Press the eli button to dispense steam This icon is displayed during the preheating time required by the machine 42 ENGLISH OP GE This icon will be displayed during dispensing When the water has HHI been completely dispensed press the button to stop dispensing MEMO Green EE Empty the container BEB caution Let the steamwand cool down for a few minutes i EH Remove the Automatic Milk Frother from the steam wand Ml E R
43. y mistake press the c l y button to quit EJ Remove the water tank and the INTENZA water filter from the water tank if it was installed replacing it with the small white original one Pour all the descaling solution into the water tank EGA Fill the water tank with fresh water up to the CALC CLEAN level and put it back into the machine Fal Place a large container 1 5 I under both the steam hot water wand and the coffee dispensing spout 52 ENGLISH te cac Aa CLEAN ad A CALC CLEAN Yellow Yellow Yellow Red Press the button to start the descaling process MEMO EJ The machine will start dispensing the descaling solution at regular intervals for approximately 20 minutes The bar on the control panel shows the cycle progress hen Note The descaling cycle may be paused by pressing the button To resume the cycle press the 2 button again This allows you to empty the con tainer or to leave the machine unattended for a short time EJ When this icon is displayed the water tank is empty GX Remove the water tank rinse it and fill it with fresh water up to the MAX level Put it back into the machine ENGLISH 53 EE Empty the drip tray and place it back Empty the container and place it back under both the steam hot water wand and the coffee dispensing spout GE Press the button t
Download Pdf Manuals
Related Search