Model: iBT230
Contents
1. Model iBT230 Bluetooth Wireless OPO FM Clock Radio Ar with USB Charging E instruction manual Questions Contact Customer Service at 1 800 288 2792 iBT230 Introduction Thank you for purchasing the iHome iBT230 This product is designed to provide high quality wireless sound for your iPad iPhone iPod or other Bluetooth audio device This instruction booklet explains the basic operation and care of the unit Please read it carefully and keep for future reference Maintenance Place the unit on a level surface away from sources of direct sunlight or excessive heat e Protect your furniture when placing your unit on a natural wood and lacquered finish A cloth or other protective material should be placed between it and the furniture e Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as benzene thinner or similar materials can damage the surface of the unit Table of Contents i BT2 3 O Whats IHCWGEd sasirnane en ETE E E E EA SE EEE 3 Meet Your BIZI U erreien n EnA EAE EEA EARE REAN EE EEEE EARE 4 The Display Setting Up the Unit 5 Replacing and Installing Clock Backup Batteries 6 Setting the Clock Setting and Using the Alarms 00cccccccccececeeeeseeeeeeeeeeteeeeetseeeetteeeetseees 7 Previewing the Alarm and Turning the Alarm On Off cccccccceceeeeeeeeeeteeeeseeetseettseetteeentees 7 8 Snooze Display Dimmer Button Sleep Mode FM Radio 9 S2. Ga i J Indicators E E E UE AM e Auxin Mode P QD Ce Indicator WAKE AUX a _ EALA eB T bat th LD Aga Set Waketo steep FM a a D D Sleep Mode Indicator FM Radio Low Backup Bluetooth Pairing Mode Battery Indicator Indicator Indicator Using the iBT230 Alarm Time Date Radio Frequenc EE Alarm Active Indicator Y Wake to source BT Bluetooth FM Radio Buzzer Mode BT Bluetooth FM Radio Aux Setting Up the Unit Connect the included AC adaptor to the DC jack located on the back of the unit and connect the other end to a working wall outlet Extend FM antenna 2 AA batteries are included for battery backup Install them in the backup battery compartment located on the bottom of the unit before using the unit See page 6 for more on installing and replacing backup batteries FM antenna Using the iBT230 Replacing and Installing Clock Backup Batteries Note 2 AA batteries are included with the unit Install them before using the unit This model is equipped with a battery backup circuit that will maintain the time and alarm time settings in the event of a temporary power interruption the display is NOT lit The battery backup circuit will also operate the buzzer alarm to wake you up at the selected wake up time even if the power is out When the backup batteries are getting weak the Low Backup Battery Indicator will begin flashing in t
3. ary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI product 2015 SDI Technologies Inc All rights reserved Questions Visit www ihome com or call 1 800 288 2792 Toll Free iBT230 141204 A Printed in China
4. as a bool Heat The uni produce heat Power Sources The uni appliance On Power Cable Pi a bed so should be y use the AC adapter that came with the unit Cleaning The unit shou Objects and Liquid Entry Care should be taken so that objec he product Attachments Do not use attachments not recommended by the lightning and Power Surge Protection Unplug the unit from the or when it is left unattended and unused for long periods of time TI Overloading Do not overload wall sockets extension cords or in Damage A the power supply cable or plug has been damaged B objects have fallen into or liquid has been spilled into the enc C the unit has been exposed to rain D the unit has been dropped or the enclosure damaged E the unit exhibits a marked change in performance or does no removed from the unit to prevent damage or corrosion should be connected to a power supply only rotection Power supply cables should be routed so tha or against them It is always best to have a clear area from where the cab d be cleaned only using a warm damp cloth For examp Ors of erence Take special note of all warnings listed in these instructions and on the unit le near a bathtub washbowl kitchen sink laundry tub swimming he unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not a tug or similar surfac
5. d release the Mode Button as needed until BT appears on the display It is autoplay audio from your linked Bluetooth device and pause Press the wi Play Pause Pairing Button on the unit to play audio from your linked Bluetooth device Press the or Buttons to go to the previous or next track Press the or Buttons to adjust the volume on the unit You may need to adjust the volume on your device too When done listening press the Power Alarm Reset Button to turn the unit off Using the Speakerphone feature NOTE The unit must be powered on and linked to a Bluetooth phone to receive a call 1 When a call is received playing music is muted to hear the ring tone CALL will flash on the display Adjust call volume on your device and or on the unit as needed Press the Button to answer the call press and hold the Button to ignore the call For call waiting function press the Button to place a currently active call on hold and answer a new call press the Button to switch between the calls When a call is completed press the Button to end the call and resume previous function Playing Audio via Aux In l Using the iBT230 Connect one end of the included standard stereo 3 5mm audio cable into the auxin jack on the back of the unit and the other end into the headphone or output jack of your audio device Press the d Power Alarm Reset Button on the unit to turn it on Press and re
6. e Display Dimmer Button to temporarily silence the alarm for the set duration 9 minutes is the default Snooze can be used several times during alarm 5 To adjust the brightness of the display press and release the Snooze Display Dimmer Button during normal operation when no alarm is sounding fo cycle through the brightness display settings Sleep Mode This unit allows you to sleep to the current sound source for a set time before turning the unit off 1 To set Sleep time press and release the Sleep Clock Adjust Button as needed to cycle to the desired sleep duration 120 90 60 30 or 15 minutes or OFF turns the unit off 2 Press the or Buttons to adjust the sleep volume on the unit Note that the sleep volume setting is stored separately from other volume settings FM Radio Extend the FM antenna for best reception Press and release the Mode Button as needed until the FM indicator icon and current FM radio frequency appear on the display 2 Press the or Buttons to tune the radio to the desired station hold to scan for the next clear station 3 Press the or 4 Buttons fo adjust the volume on the unit 4 When you are through listening press the d Power Alarm Reset Button to turn the unit off Snooze Display Dimmer Button N 9 Using the iBT230 Setting and Using FM Presets The unit allows you to store up to 6 FM radio station presets 1 Press and release the Mode Button as needed un
7. e sure your Bluetooth device is fully charged Turn on your Bluetooth device and make it discoverable by turning on Bluetooth mode check in Options or Settings gt i 2 Press and hold the Play Pause Pairing Button for 2 seconds The iBT230 will pair i beep and BT and the Bluetooth icon will flash on the display indicating the iBT230 is in pairing mode 3 iHome iBT230 should appear in your device s Bluetooth menu If Not Paired Not Connected or similar message appears select iHome iBT230 to connect it If prompted for a passcode enter 1234 on your device s keypad lt Settings Bluetooth cr Que lt Bierooth GD 07 rene Mau PRONE 63 G3 Bluetooth Cr cevces _ wer un Mind ani y iHome iBT230 Fe x oy iHome iBT230 mo O For iPhone iHome iBT230 a iHome iBT230 For other RA i 4 If pairing is successful PAIR will appear at the bottom of the display the Bluetooth icon will appear solid and 2 beeps will sound indicating the iBT230 is ready to play music There should also be an indication on your device If no device is successfully paired within 2 minutes the iBT230 will default to previous mode Once the iBT230 is paired to a device it will attempt to autolink when the device is within range about 30 feet 11 Playing Audio via Bluetooth OaARKRWN gt 7 Using the iBT230 Press the h Power Alarm Reset Button to turn the unit ON Press an
8. e that may block ventilatio case or cabinet which may impede the flow of air through situated away from heat sources such as radia n openings Also it should not be placed in a builtin installation he ventilation openings heat registers stoves or other appliances including amplifiers that he type described in the operating instructions or as marked on the they are not likely to be walked on or pinched by items placed upon Do s do not fa produc le exits the unit to where it is plugged into an AC socket not use solvents etc land liquids are not spilled into any openings or vents located on manufacturer wall socket and disconnect the antenna or cable system during a lightning storm his will prevent damage to the product due to lightning and powerline surges tegral convenience receptacles as this can result in a risk of fire or electric shock OSUre Requiring Service The unit should be serviced by qualified service personnel when operate normally Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the backup batteries should be Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel 16 iBT230 FCC Information FCC Radiation Exposure Stateme
9. etting and Using FM Presets Using FM Radio in Other Countries 10 Pairing Your Bluetooth Device ss 11 Playing Audid Vic Blu toolh saines ide tnt nt nent tete elite EE 12 Using the Speakerphone Feature 0 ccccccccceeceeeece cette eeceeeececeeeeeteeeeseteeeetsteseteeeetsteeenes 12 Playing Audio Via AUX Insee mn etais ads EE tre een 13 Charging Devices Via USB Port ssste ren ieseni i hie ie n tele eape fins 14 Bater Uss Cauions anad ipse Tente ne Is Consumer Product Safety Guide trott trst tt ertt Errr Errr EEn rrr rn rennet 16 FOC Information sise 17 Troubl shootiNgsasnesenne seen entente E E 18 VVafrant rss manne eme E IE T A E riad evene EE aten 19 What s Included i BT2 3 O e iBT230 unit e 100V 240V universal AC adaptor e Stereo audio cable audio cable iBT230 power adaptor Meet Your iBT230 Top Microphone under grille Mode Button Presets Button iBT230 Alarm 2 Button Sleep Clock Alarm 1 Butt Adjust Button ae ea Button Answer Call Plus Settings Button slee Volume Down Volume Up Buttons End Call Minus Settings Button Play Pause Pairing Button Bottom Backup Battery Compartment Snooze Display Dimmer Button Back Aux in Jack DC Jack USB Charging Port auxin DC5V2A usb charging fe 17 eee FM Antenna The Display Time Display Fr PM AM
10. he or Buttons to select the desired wake to alarm source Bluetooth radio or buzzer Wake to Bluetooth You will wake to the currently linked Bluetooth device If no device is detected the alarm will default to buzzer Wake to Radio Press the Alarm Button to confirm Press the Presets Button to select an FM preset to wake to or press the amp or Buttons to tune in a desired wake to station To set Presets see Setting and Using FM Presets on page 10 Wake to Buzzer You will wake to buzzer Press the Alarm Button to confirm the alarm settings and exit alarm setting mode 2 beeps will confirm alarm setting is complete The alarm icon will remain on the display indicating the alarm is armed To turn off a sounding alarm and reset it to come on the next day at the same time press the b Power Alarm Reset Button or the associated alarm button or to reset alarm Previewing the Alarm and Turning the Alarm On Off Press and release the desired Alarm Button as needed to toggle the alarm ON indicated by the alarm icon or OFF no alarm icon Using the iBT230 1 To program Snooze press and hold the Snooze Display Dimmer Button during normal operation when no alarm is sounding Press the or Buttons to select the desired snooze time between O1 and 29 minutes Press and release the Snooze Display Dimmer Button to confirm Snooze setting 2 beeps will sound While the alarm is sounding press and release the Snooz
11. he display When you see this flashing indicator you should replace the backup batteries as soon as possible Note We recommend alkaline batteries for best performance To install replace the backup batteries IMPORTANT When replacing the backup batteries be sure to have the unit connected to the AC outlet to maintain all of your settings otherwise it will be necessary to reset the time and alarm time after the batteries are replaced Replacing Backup Battery 1 Press tab to remove the battery door located on the bottom of the unit It replacing batteries remove the exhausted batteries 2 Insert 2 fresh AA batteries in the backup battery compartment Make sure the polarity of the batteries or nodes matches the illustration 3 Close the battery compartment door Confirm that the backup battery indicator is not flashing in the display Note Make sure you dispose of batteries properly see your local regulations 6 Setting the Clock 1 7 On Ow EO Using the iBT230 Press and hold the Sleep Clock Adjust Button for 2 seconds until the clock display lashes and a beep sounds Press the or Buttons to adjust the clock to the current time hold for rapid setting Make sure you set the correct AM PM time The AM and PM indicators appear to the eft of the display Press the Sleep Clock Adjust Button to confirm the time The year will flash on the display Press the or Buttons to adjust the c
12. lease the Mode Button as needed until the AUX indicator icon and MP3 appear on the display Place your audio device in play mode Navigate tracks and adjust output volume on the device Press the or Buttons to adjust the volume on the unit You need to adjust the volume on your device as well When done listening press the Power Alarm Reset Button to turn the unit off Remember to turn off your audio device too O am Mobile Phone PC Tablet Game Devices iPod Laptop MP3 MP4 Using the iBT230 Charging Devices via USB Port le Connect the standard size end of a USB cable not included to the USB Port on back of the unit and connect the other end to the charging port on your device It s often best to use the charging cable supplied with your device Monitor the charging on your device Some devices use a proprietary charging method and will not charge using th USB Port If this happens you must charge your device using the charger that came with it NOTE Unit must be plugged into working outlet to charge devices Using the iBT230 Battery Use Cautions and Tips Only use the recommended supplied batteries or equivalent Use alkaline batteries for longer life Do not mix old and new batteries and do not mix alkaline carbor zinc or rechargeable nickelcadmium batteries Insert batteries with proper polarity as indicated Rem
13. lock to the current year hold for rapid setting Press the Sleep Clock Adjust Button to confirm the year The date and month will flash on the display Press the or Buttons to adjust the clock to the current date and month hold for rapid setting ess the Sleep Clock Adjust Button to confirm the date and month and exit clock setting mode 2 beeps will confirm clock setting is complete U TIP To toggle the clock display between standard 12 hour time and 24 hour military time display press the Alarm Button or Alarm Button while the display is flashing during clock setting Setting and Using the Alarms This unit features dual alarms which can be set to different times and alarm sources Each is set in the same way Instructions are given as Alarm Button use Alarm Button or amp Alarm Button to set respective alarms Note Each step must be completed while display is flashing or step will time out with any changes saved Setting and Using the Alarms Continued 1 Se Using the iBT230 Press and hold the Alarm Button for 2 seconds until the alarm time display and alarm icon flash A beep sounds Press the or Buttons to adjust the alarm time to the desired time hold for rapid setting Make sure you set the correct AM PM alarm time The AM and PM indicators appear to the left of the display Press the Alarm Button to confirm the alarm time setting The wake to source will flash Press t
14. nt Do S This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device complies with Part 15 of the FCC Rules operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation e Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment e NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect
15. ove exhausted batteries from product Recharge rechargeable batteries under adult supervision Do not attempt to recharge non rechargeable batteries Do not open batteries or heat them beyond normal ambient temperatures To prevent battery leakage or damage remove batteries from a product if it will not be used for a month or longer e Use extreme caution handling leaking batteries avoid direct contact with eyes and skin If battery leakage comes in contact with eyes IMMEDIATELY flush the eye with lukewarm and gently flowing water for at least 30 minutes If skin contact occurs wash skin with clear water for at least 15 minutes Seek medical attention if any symptoms occur Store in cool dry ventilated area away from hazardous or combustible material Do not dispose of batteries in the household trash or fire Follow applicable laws and local regulations for the disposal and transportation of batteries instructions handy 1 2 10 11 Con sumer Product Safety Guide IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these or future rel Water and Moisture The unit should not be used near water pool or in a wet basement Ventilation be situated on such
16. rn it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI will repair or at its discretion replace this product without charge This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center authorized by Customer Service f service is required please call Customer Service at 1 800 288 2792 to obtain a Return Authorization Number and shipping instructions Disclaimer of Warranty OTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by por persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than o the original purchaser In no event will SDI or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any ost profits actual exempl
17. roperly plugged in e Make sure your device is properly paired with the iBT230 e Make sure the Power is ON Unit doesn t respond locked up or frozen e The unit may need to be reset To do so unplug the unit from power source and remove the backup batteries Let unit stand for 2 minutes Re install backup batteries and connect unit to power source You will need to reset the clock radio and any other settings Trouble pairing device computer with iBT230 Bluetooth implementation varies depending on your device s hardware and operating system Please see our website for updates on pairing e When you power ON the unit it will automatically link with the last previously paired Bluetooth device if the device is still within range about 30 feet To pair with a different device you must turn off Bluetooth capability on the already paired device or take it out of range e Make sure your device is working properly Check your device s manual for details on Bluetooth pairing and linking For further information and to see the latest instructions visit www ihome com support Limited 1 Year Warranty iHome Products a division of SDI Technologies Inc hereafter referred to as SDI warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of one 1 year from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first retu
18. the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAN ICES 3 B NMB 3 B IC Statement This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de license L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible ites compromettre le fonctionnement The device meets the exemption from the routine evaluation limits in section 2 5 of RSS 102 and compliance with RSS 102 RF exposure users can obtain Canadian information on RF exposure and compliance Le dispositif rencontre l exemption des limites courantes d valuation dans la section 2 5 de RSS 102 et la conformit l exposition de RSS 102 rf utilisateurs peut obtenir l information canadienne sur l exposition et la conformit de rf 17 Declaration ID D024962 Troubleshooting Unit doesn t respond no power e Check that all connections are correct and p
19. til the FM indicator icon appears on the display 2 Press and release the Presets Button as needed until the preset number P1 P6 you wish to set is displayed then press and hold the Presets Button to enter setting mode 3 Press the or Buttons to tune the radio to the desired station hold to scan for the next clear station 4 Press and release the Presets Button 2 beeps will sound to confirm the preset has been assigned Repeat steps 2 4 until you have set up to 6 preset stations 5 To listen to a preset FM station at any time follow steps 1 2 to turn on FM radio mode and cycle to the desired preset Using FM Radio in Other Countries Different areas of the world use different FM frequency steps and ranges By default this unit is set to USA frequency steps To use the radio outside the USA 1 Make sure unit is OFF 2 Press and hold the Mode Button until USA appears in the display 3 Press and release f or Buttons to cycle to your location Europe Japan Australia China or USA 4 Press the Mode Button again to exit frequency setting mode 2 beeps will confirm setting Using the iBT230 Whenever AC power is connected the iBT230 will attempt to autolink to a previously paired device If no device is paired the iBT230 will automatically enter pairing mode for 2 minutes You can manually initiate pairing without turning on the iBT230 by following steps 1 3 below Pairing Your Bluetooth Device 1 Mak
Download Pdf Manuals
Related Search