File - Alpha Catering Equipment
Contents
1. compressor and condenser fan starts Flashes when activation of the compressor is temporarily delayed FAN n a DEFROST ON when the defrost is activated Flashes when the activation of the defrost is temporarily delayed due to procedures in progress AUX n a ALARM Flashes in the event of alarms CLOCK n a LIGHT n a SERVICE Flashes in the event of malfunctions DISPLAY Shows the cabinet temperature HACCP n a CONTINUOUS CYCLE n a Table 3 Icon Functions SKOPE Backbar Remote Chiller 13 User Manual ELECTRONIC CONTROLLER Temperature Setpoint The chiller temperature setpoint is factory set at 1 0 C If necessary the standard setting can be adjusted between 0 5 C and 3 5 C see Table 4 below SKOPE do not recommend that the setpoint be changed unless it is absolutely necessary and then only by small increments at a time To View and Adjust the Temperature Setpoint To view the setpoint press and hold the SET key for 2 seconds until the setpoint value flashes To adjust the setpoint press either the UP or DOWN keys to display the required setpoint value 3 Press the SET key again to memorise the new setpoint value If this is not done within 60 seconds changes will be lost and you will need to repeat the above procedure Table 4 Viewing and Adjusting the Temperature Setpoint SKOPE Backbar Remote Chiller 44 ER ee AE User Manual SERVICING Troubleshooting Compla2. support brackets into the shelf support strips at the desired heights and fit the shelves The shelves may be positioned at different heights to suit various products Always ensure that the shelf clips are securely engaged in each of the shelf support strips The shelf support strips are marked for easy location of shelf clips SKOPE Backbar Remote Chiller 7 User Manual INSTALLATION Power Supply The chiller is supplied with a 2 3m flexible power cord fitted with a 3 pin plug which exits below the refrigeration unit front cover Initial retrieval of the power cord is from inside the refrigeration unit compartment behind the unit front cover To retrieve the power cord 1 Unit Front Cover Open the unit front cover by undoing the bottom fixing screw and then lifting the cover up from the bottom and swing open Pull the power cord fully out from the unit compartment and remove the rubber band Push the unit end of the power cord into the grey plastic clip on the front of the unit base and close the plastic clip over the cord ensuring it is held firmly in place see Figure 1 below The power cord can now be run under the cabinet and plugged into a power supply socket Close the unit front cover by lifting the cover up from the bottom and pushing firmly closed Remember to refit the bottom fixing screw Condenser Coil Unit Base Plastic Clip Power Cord Figure 1 Power Cord Clip SKOPE Backbar Remote Ch
3. Operation ELECTRONIC CONTROLLER Controller Display Temperature Setpoint SERVICING Troubleshooting Controller Alarms ON RS es ondes cou Cleaning v6 a med cc did vis Contact Addresses Warranty e ers ee hee ING SKOPE Backbar Remote Chiller User Manual SKOPE Backbar Remote Chiller User Manual SPECIFICATIONS Cabinet and Refrigeration Unit Cabinet Construction Finish Insulation Dimensions Models Doors Height excluding castors or legs Width Depth Solid Back Depth Pass Thru Floor area Internal volume Electrical Power supply Run Amps Interior light Stainless steel or powdercoated galvanised steel 50mm thick polyurethane foam Cyclo iso Pentane blowing agent C5Hj9 C5H gt BB380r 2 BB580r 3 BB780r 4 2 Door 3 Door 4 Door 920mm 920mm 920mm 1355mm 1915mm 2475mm 590 600mm with bench top 655 670mm with bench top 0 81m2 1 14m2 1 48m2 380 litres 580 litres 780 litres 220 240 V a c 50 Hz single phase power supply See rating label inside cabinet 1 x 36 Watt 1 x 58 Watt 1 x 58 Watt Refrigeration Unit Product temp Rated ambient Evap capacity Evaporator TX valve R134a TX valve R404A TX valve R22 Orifice Refrigeration tail Drain diameter 1 C to 4 C 32 C at 65 RH 480 Watts 615
4. User Manual SKOPE Backbar Chillers BB380 580 780r REMOTE models Model BB380r 2SW SKOPE Refrigeration MANO406 Rev 2 0 Feb 2008 edition SKOPE Backbar Remote Chiller Models BB380r 2 BB580r 3 BB780r 4 User Manual MANO406 Rev 2 0 Feb 2008 edition Copyright 2007 SKOPE Industries Limited All rights reserved SKOPE Industries Limited reserve the right to alter specifications without notice SEOFPE is a registered trade mark of SKOPE Industries Limited TRADE MARK INFRINGEMENT The SKOPE trade mark on this product is infringed if the owner for the time being does any of the following e Applies the trade mark to the product after their state condition get up or packaging has been altered in any manner e Alters removes including part removal or obliterates including part obliteration the trade mark on the product e Applies any other trade mark to the product e Adds to the product any written material that is likely to damage the reputation of the trade mark Notice of the above contractual obligations passes to e Successors or assigns of the buyer e Future owners of the product SKOPE Backbar Remote Chiller User Manual TABLE OF CONTENTS SPECIFICATIONS Cabinet and Refrigeration Unit INSTALLATION Safety Information Installing the Cabinet Refrigeration System OPERATION Cabinet
5. Watts 850 Watts CLS9902R VAL7923 VAL9641 VAL9643 OX REF9761 00 REF7596 00 REF7596 Liquid line 21 4 Suction line 23 8 19mm O D Table 1 Cabinet and Refrigeration Unit Specifications SKOPE Backbar Remote Chiller User Manual INSTALLATION Safety Information When using any electrical appliance safety precautions should always be observed Read these instructions carefully and retain for future reference e When used by or near young children or infirm persons close supervision is necessary Young children should be supervised to ensure that they do not play with the appliance e Do NOT use this appliance for other than its intended use e Do NOT cover the grilles or block the entry or exhaust of airflow by placing objects up against the refrigeration unit e Do NOT probe any opening e Do NOT overload the power supply See the rating label inside the cabinet for power supply and current draw e Only use this appliance with voltage specified on the rating label e Ensure adequate ventilation of the SKOPE refrigeration unit e Be careful not to touch moving parts and hot surfaces e Regulations require that all electrical work be carried out by authorised persons For your own safety and that of others ensure this is done e If the supply cord becomes damaged it must be replaced by a SKOPE authorised service agent or similarly qualified person in order to avoid a hazard e If th
6. e cabinet is disconnected from the mains power supply before cleaning the cabinet Caution Disconnect the cabinet from the mains power supply before attempting any cleaning or maintenance SKOPE Backbar Remote Chiller 19 User Manual SERVICING Contact Addresses New Zealand SKOPE INDUSTRIES LIMITED Head Office PO Box 1091 Christchurch New Zealand Freephone 0800 947 5673 Fax 03 983 3896 E mail enquiry skope co nz Website www skope co nz Australia SKOPE AUSTRALIA PTY LTD A C N 000 384 270 PO Box 7543 Baulkham Hills B C NSW 2153 Australia Freephone 1800 121 535 Fax 1800 121 533 E mail enquiry skope com au Website www skope com au Warranty To receive a warranty for your purchased cabinet you MUST register your cabinet within four weeks from the date of invoice either by e filling out the in cabinet warranty form and posting or faxing it back to SKOPE e or filling out the online warranty form Cabinets that are not registered within the four weeks are not eligible for a warranty SKOPE Backbar Remote Chiller 20 EE EE EE User Manual
7. e refrigeration unit is required to be installed or removed from the cabinet ensure all necessary safety precautions are observed e This chiller is not designed to be stable in motion Exercise caution when moving or transporting this chiller Caution Disconnect the cabinet from the mains power supply before attempting any cleaning or maintenance 6 SKOPE Backbar Remote Chiller User Manual INSTALLATION Installing the Cabinet Adjustable Legs If your SKOPE Backbar Chiller has been supplied with the optional adjustable height legs packed with the cabinet they should be fitted to the base of the cabinet before final positioning of the chiller Positioning When positioning the chiller avoid direct sunlight and warm draughts etc Adequate allowance should be made for door opening The chiller must be positioned on a level surface for the doors to shut and seal correctly and to prevent the condensate tray from overflowing Ventilation For efficient operation of the chiller it is essential that adequate ventilation be provided around the refrigeration unit Maximum recommended operating ambient temperature is 32 C at 65 RH and for tropical machines is 40 C at 75 RH Important Never store cardboard cartons or other items in front of the refrigeration unit The ventilation slots in the unit front cover must be kept clear at all times Shelves Remove all packaging material from the shelves Clip the shelf
8. ical The cabinet is supplied with a 3 core 10 Amp flexible power cord and 3 pin plug The cabinet lighting and centre pillar heater elements are protected by a 3 Amp fuse located in the unit junction box If a solenoid is fitted and controlled by the electronic controller the solenoid will need connected to the connector block inside the unit junction box Unit Pipework Cover Refrigeration Unit Compartment Suction Line Drain Tube Liquid Line Rear of Cabinet Figure 2 Refrigeration Pipework 10 SKOPE Backbar Remote Chiller User Manual OPERATION Cabinet Operation Plug the chiller into the power supply and check operation of the refrigeration unit cabinet lighting and electronic controller If the cabinet has been on its back leave for 30 minutes before running Refrigeration Unit The compressor and evaporator and condenser fans should all operate within two minutes from the time the cabinet is plugged in This may be verified by listening for compressor switch on and checking for air movement out of the top ventilation slots in the refrigeration unit front cover The compressor and condenser fans should switch off and on depending on the cabinet temperature Cabinet Lighting The light switch located next to the electronic controller on the refrigeration unit front cover activates the cabinet interior lighting and can be switched on or off as required The fluorescent lights will require a period of time to stabilise f
9. iller User Manual INSTALLATION Refrigeration System Drain A 500mm long 19mm O D PVC drain hose is supplied All drainage is to conform to local regulations covering removal of condensate to waste water Ensure drain is trapped with adequate fall Venting the drain may be required for a restrictive run Refrigeration lines A 1 4 liquid line and 3 8 suction line are provided to attach pipe lines to The suction lines must be insulated NOTE The electronic controller supplied with the cabinet can switch a solenoid No solenoid is supplied with the remote unit Refrigeration Practice Installation must be performed by a refrigeration tradesperson to an appropriate standard complying with all local regulations Performance depends on the overall installation including condensing unit Cabinet suitability must always be quantified for the application The final responsibility for condensing unit performance and component selection rest with the installer The installer must check matters such as e Heat load e Refrigeration load e Variable operating conditions usage ambient humidity e Refrigeration pipe sizing e Refrigeration pipe length distance elevation pressure drop e Location and ventilation cabinet and condensing unit e Drainage e Power supply e Unit is fully evacuated prior to charging e All cabinet penetrations are sealed SKOPE Backbar Remote Chiller 9 User Manual INSTALLATION Electr
10. int Possible Cause 1 Cabinet not e Loss of power supply e Check mains power supply operating and no controller display 2 Cabinet lights not Blown cabinet fuse e Requires technical repair by a operating SKOPE Authorised Service Agent Failed fluorescent tube Check fluorescent tubes e Controller alarm e Determine cause and eliminate see pages 16 17 3 Product is too e Restricted cabinet airflow e Ensure product is not blocking warm and airflow slots and there is air space spoiling around all the product e Temperature setpoint is too warm e Adjust setpoint see page 14 Table 5 Troubleshooting SKOPE Backbar Remote Chiller User Manual 15 SERVICING Controller Alarms CODE DISPLAY ICON ALARM DESCRIPTION Product HIGH temperature alarm Product LOW temperature alarm Ambient probe fault Evaporator probe fault Condenser probe fault Defrost over time limit Real time clock fault Controller E prom error Controller E prom error Start defrost request End defrost request Table 6 Controller Alarms 16 SKOPE Backbar Remote Chiller User Manual SERVICING INITIAL ACTION FINAL ACTION 1 Check the cabinet product loading to ensure ventilation slots are not blocked and that product does not overhang the shelves 2 Ensure the cabinet is installed with good refrigeration unit ventilation 3 Unplug cabinet from the power supply for 1 minute then reconnect to power s
11. ollowing initial start up Electronic Controller At initial start up the electronic controller will display the current cabinet temperature See pages 12 13 for controller display Loading Product The chiller should be left running for 30 minutes before loading with product When loading the cabinet shelves with product e Allow air space around all the product to ensure even cooling and efficient operation of the chiller Leave airspace above product loaded on the top shelf and leave a gap of approx 50mm next to the return air grille between the cabinet interior and the refrigeration unit compartment e Do not allow products to overhang the front of the shelf as this could prevent the doors from shutting or cause glass breakage e Do not exceed a maximum loading of 20kg per shelf e Remove some product if the shelves are flexing or bending SKOPE Backbar Remote Chiller 11 User Manual ELECTRONIC CONTROLLER Controller Display Prg mute To initiate programme sets press for 5 seconds Mutes the audible alarm buzzer and deactivates the alarm relay UP aux To scroll settings UP in programme mode Set If pressed for more than 2 seconds displays and or enables changing the temperature setpoint see page 10 DOWN def To scroll settings DOWN in programme mode Table 2 Keypad Functions SKOPE Backbar Remote Chiller 12 hE Oem User Manual ELECTRONIC CONTROLLER Icons COMPRESSOR ON when the
12. upply If alarm persists contact SKOPE Unplug cabinet from the power supply for 1 minute then reconnect to power supply SKOPE Backbar Remote Chiller 17 User Manual SERVICING Lighting Cabinet Interior Lights The chiller is fitted with a full length horizontal interior light The light houses one fluorescent tube See Table 6 below for the correct tube size Fluorescent Tube Qty KARA 2 30 Watt T8 fluorescent tube 26mm x 915mm 1 BB580r 3 36 Watt T8 fluorescent tube 26mm x 1219mm HERR BB780r 4 58 Watt T8 fluorescent tube 26mm x 1524mm Table 7 Fluorescent Tube Sizes To Replace the Fluorescent Tube 1 Disconnect the cabinet from the mains power supply 2 Remove the top light diffuser by compressing the back section of the diffuser until it disengages from the aluminium housing and then push the diffuser back see Figure 4 below 3 The fluorescent tube can now be removed by revolving the tube until the pin position allows withdrawal 4 When refitting the light diffuser engage the back section into the housing and then compress and snap the front section of diffuser back into place working along the full length of the light Fluorescent Tube Top Light Diffuser Figure 4 Replacing the Fluorescent Tube SKOPE Backbar Remote Chiller 18 EER User Manual SERVICING Cleaning When necessary wipe both the interior and exterior of the cabinet with a damp cloth Ensure th
Download Pdf Manuals
Related Search