Home
252_GSM-SMS-ETH Controller User Manual EN mart
Contents
1. 90 2 4 Electrical characteristics Power supply 12V DC adapter Back up power Battery 12V DC Consumption in Stand By mode 70 mA Average consumption 350 mA Average power consumption in Stand By mode 0 84 W Maximum power consumption 4 2 W GSM SMS ETH Controller User Manual 2 5 LED indication Indication of unit is consist of three LED which shows its moment status The statuses depend of led indicators are shown in table 1 LED Status Modes of GSM SMS ETH Controller Green Light Device is starting Green Blink Device is in working mode Red Light GSM is starting Red Blink GSM is in working mode Blue Blink every 1 seconds Search for GSM network Blue Blink every 3 4 seconds Device is connected to the GSM network Table 1 LED conditions 2 6 GSM Frequency range 850 900 1800 1900 MHz Maximum output power class 4 2 W class 1 1 W SIM card 3V plug in e Antenna SMA connector female 50 Q 2 7 Data interface For configuration and update of firmware of GSM SMS ETH Controller use the USB cable which consist in the box Parameters of the interface e connector mini USB type B e ver USB 1 0 Mini USB Type AB 12 3 4 4 Female Receptacle GSM SMS ETH Controller User Manual 2 8 RS 232 interface connector Canon 9 male pins 2 Rx 3 Tx 4 12V out 5 Ground 7 RTS 8 CTS 2 9 LAN interface connector RJ45
2. EK LEXIM GSM SMS ETH Controller User manual Ver 2 9 This document contains technical information and user manual for GSM SMS ETH Controller models 3D3K and 3D3K RS232 In this document you can find information how to connect and configure these models Last update 21 03 13 Copyright 2013 Elexim LTD Content Introduction l Package contents iste Aca atin ebece a a lta a i a maaan 6 2 Technical parameters 2 EDimens ions renn a a a a e ohn shes a 7 2 2 Front and rear PANGS sessenenreienenr nonnene E E EK Ran 7 2 3 Operating characteristics xz anserats caster vevucns ceameesbeesauncncansataettarewencewmiensene 8 2 4 Electrical characteristics 2 ciate sesvssccsn Inavbavundleeslevds vo sues teumalacevvesaddn dabvaielts 8 DATE DTTC AIO Biss tas sco vss asseoe sa pach as oS yb E E Had ATE aE Cae dea es oases 8 98 ONS poh og eee RORY T A URNAR RUN ON A ARES ASTORIA ARO REY Seth ATER OL IR RIERA 9 2 7 Data WNGCTL ACE 56 5550 Sis shdicndval teduvins a a a a ai 9 2S RS 232 tera Espn Sa ates e ed da eed ced a a e aliea as 9 DOAN ANGEL ACS ar enseia rea NETE TATE EREE 10 3 Getting started 3 1 SIM card and antenna connection sessesessesssesseseeseressesssesserrsseessses 11 3 2 Connection of consumers and sensors to I O ports cceeeeeeeeees 12 SENS OLS as hs tacne sce oem aaeseasnad soaanedyneneeaumsstuadusanoeeigeneatencannant EET 12 MTS AY Seis as beta sat aust Meant anise a date uel cata tal ase e i
3. standard Ethernet 10 100 Base T IEEE 802 3 TA vox Panel Ground 4 L 4 L Optional zI Yellow LED 2 o Green LED 1 10 GSM SMS ETH Controller User Manual 3 Getting started 3 1 SIM card and antenna connection Before you start GSM SMS ETH Controller insert SIM card and switch the antenna as it shown on picture 3 1 picture 3 1 Note SIM card inserted in the device must be with disabled PIN code In other case the device will not start properly Note Put the antenna in place where you are sure it has good GSM network coverage Places with bad coverage basements villages etc may cause the problems with normal start up of the device and lead to occurrence of noise during dialing or calls Picture 3 2 11 GSM SMS ETH Controller User Manual 3 2 Connection of consumers and sensors to I O ports Sensors GSM SMS ETH Controller has 3 inputs for connection of different sensors which will alert its owner when is activated Inputs 1 and 2 D1 and D2 serve to connect sensors to them operable in open contact When a sensor is activated the device send a SMS to one phone number or group of numbers ring to one or more numbers preset in its memory or send an email You can choose how to alert you with SMS with ringing or with e mail Example of connection of inputs D1 and D2 is shown in the picture 3 2 D1 D2 3 2 Example of connection of sensors to inputs D1 and D2 Input 3 D3 ser
4. of power supply GSM network and battery charge Audio connection through external microphone and headphones Access only from authorized numbers Remember the state of switches even the main power supply fails Easy configuration via USB Backup power supply external battery when main supply fails It works only for model 3D3K RS232 GSM SMS ETH Controller User Manual Attention 1 Read this manual carefully before exploitation 2 Do not put the device directly on sun or rain 3 Mount the device on a stable surface 4 Do not put the device in places where it can be soaked with liquid next to heat emitting devices as air conditioner stoves dusty or not good conditioning places 5 Do not cover the device This can lead to overheating 6 Do not drop the device This can lead to its failure 7 To power up the device use only the adapter included in the box Using other adapters may damage it 8 Do not switch the device directly to a 220V electricy This may damage it 9 Mounting and setting of the device should be done only from qualified stuff GSM SMS ETH Controller User Manual 1 Contents of the package GSM SMS ETH Controller is delivered to the client in cardboard box with all required supplements necessary for work Package consists of GSM SMS ETH Controller Adapter AC DC 110 220V 12V 1200mA Antenna USB cable for settings USB type A mini USB type B CD with software for settings a
5. s LAN settings in tab Network You have to write IP address Mask and Gateway address of the network You can change the username and password of the page for access By default they are username admin password password The port which the web server use is port 80 and can t be changed To access the unit web server when it is connected behind router you have to forward the IP address to different port Port forwarding setting of your router Email configuration To receive email when a sensor is activated you have to fill the setting for email server SMTP server in tab Email You have to point an email address from which they will be send an email for receiver and to write a Subject of the email which will be send All these settings are made in tab Email in configuration software and have to be uploaded in the device To work sending of emails correctly the SMTP server which is chosen must be with plain text authorization no encryption is allowed RF Control u temperature sensor control To switch On Off the Wireless radio transmission to the Wireless relays you have to use the command RF Control Enable When using the additional module Wireless module for remote control of 3 relays with in build temperature sensor you can set a minimum or maximum temperature When one of these temperatures are reaching an event may occurs call to a defined phone number send a SMS or e mail switch On Off a relay 1
6. the number of the SIM card put into the device 230VU AC The lamp will light when the relay is turning ON d ail Example of connection of relays K1 K2 and K3 13 GSM SMS ETH Controller User Manual Audio connection GSM SMS ETH Controller has an external connectors for microphone and speaker Due to this you can make an audio connection when one of the sensors is activated and can hear what happen in the room where the device 1s It is possible to make audio connection with direct call to the SIM card inserted into the device too but it is necessary to preset this feature in the configuration file RS 232 Due to RS 232 connection you can connect additional modules to GSM SMS ETH Controller The communication between the device and these modules is made with RS 232 protocol Thanks to this you can expand the number of operated relays or the number of sensors for monitoring and include specialized management schemes on client s request Using Telnet server or similar terminal you can connect to devices connected to RS 232 port and control them remotely Back up power supply GSM SMS ETH Controller allow to connect back up power supply battery which will powered the device when the main power fails Depending on the capacity of the battery unit will continue to work for a certain period of time until the battery voltage reaches the minimum threshold of 10 5 volts Requirements for the lead acid battery minimum
7. 8 GSM SMS ETH Controller User Manual 4 2 Shell commands Using a proper terminal software for connection to the RS232 port of device you can use some additional system commands Commands version check the software version cat config config ini read the configuration file written in its memory cat config mac ini read the MAC address of the device switch n m where n is a number of the relays and m is 1 on or 0 off serial XX XX start the connection to the serial port of the device At XXXX you have to write the speed of transfer of data If you do not write anything in this place the speed will be by default at 9600 b sec To stop the communication to the serial port use the combination Ctrl C reset restore the default configuration If you use Telnet server you need to write username and password for access They are same as this which is use for Web server access More about Terminal commands you can find in Application C 4 3 Firmware update If you want to install newer firmware version please visit our website at www elexim com downloadbg php and download the newest version for your unit Detailed information about firmware installation can be found in document Firmware update of GSM SMS ETH Controller pdf in the folder of the firmware Important note Please be sure that you download the correct firmware version for your device If you are not sure if the version is compatib
8. alled on your computer To set the configuration of GSM SMS ETH Controller first install the program Elexim GSM ETH Controller Tool which can be found in the Installation CD User manual for installation and configuration Client manual ver 0 1 5 EN pdf you can find in the CD in folder Docs If you have any troubleshoots with configuration and setting the device please contact the manufacturer or ask for help from the competent staff Description of settings of GSM SMS ETH Controller Authorized access numbers GSM SMS ETH Controller allow to be inserted up to 255 numbers which will have access to control the device This numbers must be written it menu List in the software for configuration All numbers must me written in international format and must consist the prefix of the country prefix of the city or the mobile operator and phone number Only the numbers written in this table will have access to control the device SMS and calls from all other numbers will be rejected Configuration of incoming calls A ringing from authorized number to the SIM card inserted into the device can restart relay K1 establish audio connection nothing to happen If you choose to restart relay K1 with ringing you have to set the time of restarting the time which device wait before go to position 1 again This time must be in interval of 1 to 60 sec Example if you set rresart time to 5 sec and you ring to the device rel
9. ay K1 will go in position 3 for 5 sec After this time expire the relay will go in position 1 16 GSM SMS ETH Controller User Manual Note If at the time of ringing the relay K1 is in position 3 it will not change its position at first and after the time which is set it will go in position 1 If you choose to activate audio connection when you ring to the device it will establish audio connection between your Mobile phone and it You will have the opportunity to listen what happen in the room in which the device is if an external microphone is connected Configuration of sensors All phone numbers which want to receive information when a sensor is activated must be written in table Sensors Notification in menu List You can add up to 255 numbers in this table When one of the sensor is activated device will ring to one number send a SMS to one number ring to the group of people send SMS to the group of people send SMS and after that ring to one number send e mail to one mailbox Each sensor can set differently how to inform that it is activated In example sensor can be set to send SMS sensor 2 to ring to 1 number and sensor 3 to send SMS to all numbers written in the table These settings are made in configuration software in tab Sensors If you want you can change the text of the SMS which you receive It s length must be not more than 30 symbols You can label each sensor with dif
10. capacity of the battery 1200 mAh recommended capacity of the battery 4500 mAh nominal voltage 12 V maximum charge current 150 mA minimum voltage of the battery 10 5 V LAN The control of the unit can be made not only through GSM network but through LAN connection too Through LAN you easily and quickly can check the status of sensors and switch relays To control the device through Internet it is necessary to set the IP address to which it will be connected Configuration is made via USB by using the special configuration software Write down the IP in your browser and you will see a page for access to the device The access to the device is protected with username and password so don t 14 GSM SMS ETH Controller User Manual forget it Important Note Setting of the GSM SMS ETH Controller can only be done via USB cable connected to PC Changing the settings can not be done via Web based interface or with SMS 3 3 Connection of power supply If you are sure that SIM card is inserted the antenna is switch and all sensors and electrical consumption are properly connected you can connect the power supply We strongly recommend you to use the adapter which is included in the set If you use adapters different from this in the set the manufacturer are not responsible for damage caused by using other power supply 3 4 Starting If you done all steps described above the device will start working Initially the red le
11. d and green LEDs will light constantly The green LED will start blinking then the processor is started The red LED will start blinking when the GSM module establish connection with the processor The blue LED will start blink every 3 4 sec when the device establish connection with the GSM network If blue LED blink more often every 1 sec this mean that the GSM can t connect to the GSM network The green LED blink when everything work without any problem and light constantly when something not work properly Most common reasons for failure to start the unit e You forgot to insert SIM card in the unit e You forgot to disable the PIN code of the SIM card e The antenna is put in place with bad coverage of GSM network e Your power supply does not meets the requirements If launching the device fails for any reason not mentioned above please contact the technical staff for more information and assistance It is possible to start the device without inserting SIM card but in this case you can control the device only trough LAN You will not receive notification when one of the sensors is activated and will be impossible to switch relays with SMS 15 GSM SMS ETH Controller User Manual 4 Configuration and software update 4 1 Configuration of the software To operate the device according to the client Bucxec it must be configured before nonnenranr all sensors and electrical consumers The setting is done via USB cable by software inst
12. eee 13 S AUCIO COMME CATOE m orae ee a E E e ETER 14 Hack p DOW CL oirrne inn ies E EE EE TE R ia AEE EAS 14 RS 232e o E seaton aneaeatt meaeuceomeayar iets 14 SCAN a a a a ene tint ara E 14 3 3 Power supply connection sssssesssssssssessesssessseessesssrsssresseressesssesseee 15 3 4 Start the device ensein enire n a date salon EE AS A AE ENE E 15 4 Configuration and software update 4 1 Configuration of the software ss sccssveesdse ds aideststensanieevabcesasdedavieesal evans 16 Authorized access numbers 355 cscccasesaecenwsiatiadialvcnds tution ccesatesattuadiod eats 16 Configuration of incoming Calls 2 0 eeeceeesceeesecesteeeseeeeesteeensaes 17 Configuration of sensors f5 ssncersdseeiedsadtadensdtecoasivaadnancrdcgunisesiedastosees 17 DAN configuration meee e E E S e aS 18 Email COMMS UL ANION sssri enr nie vas valor E Hae awe alae 18 RF Control and temperature sensor control E E 18 AD Shell command Sesera e E a EEEE E ERa 19 43 Firmwareupdate iieo sesser daar eenaa EEE OAE O ER N aA 19 44 Default SE GUIS S inire ie E E E RE EE a A R 19 S LECHMIC Al SUPPOUL A aA EA A A 21 O APPHCANONS iTr K a a Ea a TE A ES 22 GSM SMS ETH Controller User Manual Introduction GSM SMS ETH Communicator 3D3K A is highly professional and intelligent system with digital control Thanks to that system you can receive information of changes in the status of your secure or conditioning systems rooms etc Remot
13. ely control of electrical devices manufacturing process machines communication equipments and etc Make audio connection Management is done through GSM network with ringing or sending a SMS to the SIM card placed into the device or over Internet using our web base interface Application of GSM SMS ETH Controller is very appropriate in Heating systems Alarm systems Fire protection systems Systems for monitoring and control Automated systems in manufacturing Pump stations Vehicles Communication equipment and servers Measuring systems for temperature humidity fluid levels and more GSM SMS ETH Controller User Manual Main features 3 outputs for switching active loads with power up to 2 kW via 3 low voltage relays 3 inputs for sensors 4 Wireless relays for switching active loads with power up to 3 5 kW additional module connected to RS232 port Switching the relays with SMS with specific text Notification when sensor is activated through SMS call or e mail Notification when the main power supply fails low GSM network signal or low battery charge LAN connection for remote control through Internet RS 232 port for communication over RS 232 protocol Monitoring the temperature in rooms and notification when a Minimum or Maximum temperature is reached Remote check the status of relays and sensors over LAN or with SMS Monitoring
14. ferent name so to know which sensor is activated when you receive a SMS These two functions is set in Sensor Name and Sensor SMS Text boxes When activated one of the sensor you can set the minimum time it must stay activated to send SMS or call to one number This settings are made in box Sensor Time and can be from 0 to 255 seconds Example If you connect magnetic sensor for doors to D1 and set Sensor Time to be 0 seconds with the shortest opening the door sensor will trigger and GSM SMS ETH Controller will inform you that D1 is activated If you set this time to 5 seconds and someone open the door for shorten time than 5 seconds D1 will not trigger immediately The device will track D1 for 5 seconds and if it is still activated only then it will send a SMS or ring 17 GSM SMS ETH Controller User Manual Configuration of notification for low GSM network signal low battery charge or_ when main power supply fails When the main power fails the battery is discharged or the GSM network is weak you can receive SMS or email for every one of these cases Thus you will be always well informed and can take appropriate action fast You have to make these setting in tab General and to point whether you want to receive or not a SMS or email This settings is only usable when you have a back up power supply connected to the device back up battery LAN configuration To control GSM SMS ETH Controller through Internet you have to set it
15. g the software version version Command for checking the software version Reset the device settings reset Command for reset the device settings and write the default settings Format the device format Command for formatting the device memory Access RS232 port serial XXXX Command for access to the RS port At the place of XXXX you write the bit rate of transmitting the data 9600 Kb sec by default 24
16. le with your unit please contact the manufacturer or ask the competent staff for assistance 4 4 Default settings You can restore default setting of the unit every time you want Go to C Program Files Elexim GSM ETH Controller Tool and use the config ini file to restore the default settings Open this file with configuration software and upload it into unit Default settings time for restarting relay K1 5 seconds event in activation of the sensor ring to 1 number 19 GSM SMS ETH Controller User Manual time for sensor activating second name of the sensors Sensorl Sensor2 Sensor3 text ofthe SMS Activated sensor event for an incoming call relay restarting automatically or manually deleting of SMS manually rf control inactive save switch mode active phone numbers in access lists none empty LAN configuration ipaddr 192 168 5 150 mask 255 255 255 0 gateway 192 168 5 1 username admin password password Email configuration smtpip 92 168 5 1 user yourusername password yourpassword to to example com from from example com subject Elexim GSM ETH Controller msgl Sensor was activated msg2 Sensor2 was activated msg3 Sensor3 was activated 20 GSM SMS ETH Controller User Manual 5 Technical support If you encounter a problem while using the device and you are not able to solve them please follow these direc
17. nd user manual Supported elements Guarantee sticker VVVVVV WV Please check if all components described in the kit are contained in the cardboard box If any of the components is missing from your package please contact manufacturer s representative or salesperson Note The manufacturer does not provide SIM card which is necessary for connecting to the GSM network SIM card can be obtained only from licensed GSM operators GSM SMS ETH Controller User Manual 2 Technical characteristics 2 1 Dimensions 2 2 Front and rear panel Front panel 1 SIM place for SIM card 2 Antenna place for GSM antenna 3 Audio out connector for audio signals 4 Mic connector for microphone 5 Network signaling for GSM network 6 GSM signaling for GSM part 7 Ready signaling for operating of device 8 USB USB connector 9 ETH LAN connector GSM SMS ETH Controller User Manual Rear panel 10 Relays outs for relays 11 Sensors inputs for sensors 12 12 V Out output for 12V for power a specific sensors 13 RS 232 Canon 9 jack for communication over RS 232 protocol 14 V bat power connector for back up power battery 12V DC 15 Power power connector for adapter 12V DC Only for model 3D3K RS232 2 3 Operating characteristics Weight 250 gr Operating temperature 0 45 C Storage Temperature 10 60 C Humidity 10
18. ou will receive a SMS sensors with statements of all relays and sensors Checking the temperature Temp Send a SMS with text temp and you will receive a SMS with the temperature of the temp module If you put the sign at the end of any SMS you send you will always receive a SMS with the statements of all relays and sensors With one SMS you can switch only one relay You can t use SMS with text On 123 to switch all 3 relays Using only with connected Wireless module for remote control of 3 relays with in build temperature sensor 23 GSM SMS ETH Controller User Manual C Terminal commands Telnet or Hyper terminal Action Command Description Switching relays switch N M Switching relays where N 1 2 or 3 is the relay number and M 1 or 0 where 1 on 0 off Checking the status of relays switch Command for checking the status of relays Checking the status of sensors sensor Command for checking the status of sensors Checking the temperature temp Command for checking the temperature of the temp module Checking theMAC address of the device cat config mac ini Command for checking theMAC address of the device Checking the configuration of ht device cat config config ini Command for checking the configuration of ht device Checking the wireless relays codes cat config rfcodes ini Command for checking the wireless relays codes Checkin
19. tion Please check once again the SIM card antenna and power supply to be connected as in it describe in User manual Please check the PIN code of SIM card It must be disabled Please check all sensors and electrical consumption that are correct connected Set device back to default factory settings if you have problems with some of the functions Download and update newer firmware and configuration file from manufacturer s website at www elexim com downloadbg php If you have troubles with drivers download themwww elexim com downloadbg php from If you have troubles that you can t solve alone please contact us at tel 359 2 9718880 or write an e mail to us at support elexim com We always will assist you to resolve problems associated with our devices 21 GSM SMS ETH Controller User Manual Application A Schematic of sensors and relays Sensors aS TNC 1C 0512 P3 22 GSM SMS ETH Controller B SMS commands User Manual Action Command Description Switch On relay On x Send a SMS with text On X where X 1 2 or 3 depending which relay you want to switch On Switch Off relay Off x Send a SMS with text Off X where X 1 2 or 3 depending which relay you want to switch Off Restarting relay Reset x Send a SMS with text Reset X where X 1 2 or 3 depending which relay you want to restart The time of restarting is form 1 to 60 sec Checking status of relays and Send a SMS with and y
20. ve as inputs 1 and 2 to connect a sensors but its activation is through the flow of current at the entrance Example of connection of input D3 is shown in the picture 3 3 3 3 Example of connection of sensors to input D3 For more information about sensor connection please see Application A 12 GSM SMS ETH Controller User Manual Relays GSM SMS ETH Controller has 3 relays which can switch on off electrical consumers Directly to the outputs of the relays can connect small loads with maximum parameters 10A 30VDC 10A 250VAC active loads up to 2kW It is not allowed to connect loads with higher power Switching circuits running over this values must use external switches For connection of inductive loads is desirable to use external switches The pins of the relays are shown in the picture below 1 normally closed 2 middle point 3 normally open Switching of relays is made with SMS with specific text On n or Off n where n is the corresponding number of relay It is possible to switch more than one relay with one SMS separating the different relays with comma Only relay K1 allow to be restarting with ringing For model GSM SMS ETH Controller 3D3K RS232 is possible to extend the relays up to 7 by means of 4 wireless relays and additional equipment It can be done with a special module connected to the RS 232 port Example if you want to switch on relay K1 send a SMS with text On 1 to
Download Pdf Manuals
Related Search
Related Contents
ASUS P9A-I/C2550/4L C9073 User's Manual 取扱説明書|コンクリートフェンスベース KBM45N:マスプロ電工 PDF/ 65 KB Origo™ Mig 320 Philips N Coffee maker HD7455/40 Newstar FPMA-D940 (Versão 005) - 3.03 MB - ELO Sistemas Eletrônicos South Carolina USER MANUAL - KIT Solutions Support Site LCD-P462 Copyright © All rights reserved.