CCT6010 - Kleenmaid
Contents
1. 6 Connection of the hob The ceramic hob can be connected in different ways Monophase 230V 1P N Biphase 400V 2P N Setting up the configurations For the various kinds of connection use the brass bridges which are in the box next the terminal Monophase 230V 1P N Put the bridge between terminal 1 and 2 Attach the earth to the terminal earth the neutral N to terminal 4 the Phase L to one of the terminals 1 or 2 Biphase 400V 2P N Attach the earth to the terminal earth the neutral N to terminal 4 the Phase L1 to the terminals 1 and the Phase L2 to the terminal 2 Caution Ensure that you Correctly attach the wires and the bridges Tighten the screws properly Frequent loosening and screwing of the screws on the connection box risks damaging the efficiency of the tightness once screwed It is therefore advisable to keep screwing and unscrewing to a minimum Ensure that the cables are correctly inserted and tightly screwed down We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection 15 Warranty and Service Domestic Warranty Full three year warranty In addition to all statutory rights which you the Purchaser have under relevant laws in respect of this appliance during the first three years of ownership as the original purchaser2. displays Display L on 4 displays 0 or H on 4 displays No light on the displays COOKING ADVICE Examples of cooking power setting The values below are indicative 1 to2 Melting Sauces butter chocolate gelatine Reheating Dishes prepared beforehand 2103 Simmering Rice pudding sugar syrup Defrosting Dried vegetables fish frozen products 304 Steam Vegetables fish meat 4to5 Water Steamed potatoes soups pasta fresh vegetables 6 to 7 Medium cooking Meat eggs sausages Simmering Goulash roulade tripe 7 to 8 Cooking Potatoes chips 9 Frying roasting Steaks omelettes fried dishes Boiling water Water MAINTENANCE AND CLEANING Switch off the appliance before cleaning Do not clean the hob if the glass is too hot because there is a risk of burning e Remove light marks with a damp cloth with washing up liquid diluted in a little water Then rinse with cold water and dry the surface thoroughly e Highly corrosive or abrasive detergents and cleaning equipment are likely to cause scratches and must be absolutely avoided e Do not ever use any steam driven or pressure based appliance Do not use any object that may scratch the ceramic glass e Ensure that the pan is dry and clean Ensure that there are no grains of dust on your ceramic hob or on the pan Sliding rough saucepans will scratch the surface e Spillages of sugar jam jelly etc must be remov
3. touch with the waste collection centre of your council that is familiar with the recycling of household appliances 13 INSTALLATION INSTRUCTIONS The installation must be perfomed by a qualified electrical contractor How to stick the gasket The gasket supplied with the hob prevents the intrusion of liquids into the cabinet below It s installation has to be done carefully in conformity with the following drawing 2 mm Stick the gasket 2 two millimeters from the external edge of the glass after removing the protection tape 3 Fitting installing The cut out sizes are Cut size mm Glass size mm Ref Width Depth Width Depth Thickness w d CCT6010 560 490 590 520 4 CCT8010 750 490 780 520 4 e Ensure that there is a distance of 50 mm between the hob and the wall or sides hobs are classified as Y class for heat protection Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear and tall units or a wall at one side On the other side however no unit or divider must stand higher than the hob e The piece of furniture or the support in which the hob is to be fitted as well as the edges of furniture the laminate coatings and the glue used to fix them must be able to resist temperatures of up to 100 C e Do not install the hob at the top of a non ventilated oven or a dishwasher e
4. warm Function This function allows the cooktop to reach and maintain automatically a temperature of approximately 70 C This will avoid liquids overflowing and burning on the bottom of the pan The key is located between 0 and 1 e To engage to start the function Keep warm Action Control panel Display Zone selection Press display O selected O to 9 or H To engage Press between 0 and 1 U To stop Press on display U selected U Slide on the SLIDER O to 9 or H This function can be started independently on all the heating zones When the pan is removed from the cooking zone the Keep warm function remains active for approximately 10 minutes The maximum duration of keeping warm is 2 hours 10 Control panel locking To avoid accidentally activating or interfering with a setting of cooking zones in particular during cleaning the control panel can be locked with exception of the On Off key 0 e Locking Action Start Hob locking e Unlocking Action Start Within 5 seconds after start Unlocking the hob Control panel press on key 0 1 press simultaneously and 0 from the front right zone display re press on display 0 from the front right zone Control panel press on key 0 press simultaneously and L from the front right zone display press on key 11 Display 0 or H on 4 displays No modification L on 4
5. E Error message Electronic failure H Residual heat The heating zone is hot L Locking Control panel locked U Keep warm Maintain automatically at 70 C II Pause The hob is in pause STARTING UP AND APPLIANCE MANAGEMENT Before the first use Clean your hob with a damp cloth and then dry the surface thoroughly Do not use detergent This may cause blue tinted colour on the glass surface SLIDER zone and timer setting zone To select the power with the slider slide your finger on the SLIDER zone You can also directly access a particular level if you put your finger directly on the chosen level SLIDER zone and timer setting SLIDER e Start up switch off the hob Direct access Starting up Action Control panel Display To start Press key 0 1 4 x 0 are blinking To stop Press key 0 1 Nothing or H e Start up switch off a heating zone Action Control panel Display Zone selection Press display 0 selected 0 and control light on To set Slide on the SLIDER 0 to 9 or adjust the power to the right or to the left U To stop Slide to 0 on SLIDER 0 or H or press on 0 O or H If no action is made within 20 seconds the electronics returns to waiting position Residual heat indication After switching off of a heating zone or the complete stop of the hob the heating zones are still hot and indicate H on the display The symbol H disappears when th
6. Ensure under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device e If a drawer is placed under the hob avoid putting into this drawer flammable objects for example sprays or non heat resistant objects e Materials which are often used to make worktops expand on contact with water To protect the cut out edge apply a coat of varnish or special sealant Particular care must be taken when applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture This gasket ensures a good seal when used in conjunction with smooth work top surfaces e The safety gap between the hob and the cooker hood placed above must comply with the recommendations of the hood manufacturer In case of no instructions a distance of 760 mm minimum should apply e The connection cord should not be subjected to any mechanical constraint e The cooktop underside temperature exceeds 95 c an underbench board is required to be installed to prevent the underbench access WARNING Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance The use of inappropriate guards can cause accidents 14 ELECTRICAL CONNECTION e The installation of this appliance and the connection to the electrical network should be entrusted only to an ele
7. Make sure that the ventilation of the appliance works according to the manufacturer s instructions Do not put or leave empty saucepans on the vitroceramic hobs e Sugar synthetic materials or aluminium foil must not contact the heating zones These may cause breaks or other alterations of the vitroceramic glass by cooling switch off the appliance and take them immediately off the hot heating zone be careful do not burn yourself e WARNING Danger of fire do not store items on the cooking surface e Never place any hot saucepan over the control panel f a drawer is situated under the installed appliance make sure the space between the content of the drawer and the underside of the appliance is at least 2 cm This is essential to ensure correct ventilation e Never put any inflammable object eg sprays into the drawer situated under the vitroceramic hob Cutlery drawers must be resistant to heat Precautions in case of appliance failure e l a defect is noticed switch off the appliance and turn off the electrical supply e lf the ceramic glass is cracked or fissured you must disconnect the appliance at the switchboard and contact the after sales service e Repairing has to be done by specialists Do not open the appliance by yourself e WARNING If the surface is cracked switch off the appliance to avoid the possibility of electric shock Other precautions e Make sure that the cooking pan is always centred on t
8. PRECAUTIONS IN CASE OF APPLIANCE FAILURE zuuununnnnnnunuununnunnnnnnnnnnunnnnnnannnunnnnunn nn nnunnnnnnnnn nnmnnn nnmnnn ennnen 6 OTHER PRECAUTIONS idas 6 DESCRIPTION OF EHE ARPEIANGE 0d id eed a ee aie 6 TECHNICAL CHARACTERISTICS ada 6 a a Nee Besen 7 SENSITIVE TOUCH a deve adandowideecucte aduescwads cauauva dedvasweadzeaeua ici 7 DISPLAY a ainia dabuveveseceae 7 STARTING UP AND APPLIANCE 8 BEFORE THE FIRST USE uc 8 SLIDER ZONE AND TIMER SETTING 2 8 STARTING SUP cc dads ce ates A cast ceauaesacasaveasuacaave 8 2 rE a aAa a ra aa oi eaaa e ea aA aaa Aara a A daaa Naaa oaei aieia nio paana ia hanen euin 8 EXTENSION ZONE 2 2 E A E A E E A E E E EE 8 A O 9 AUTOMATIC COOKING a 10 PAUSE FUNCTION iaa eee te 10 RECALL FUNCTION sand Scccacacsceecaa zcudade2 cguesdaaeatuaud 10 KEEP WARM gt 2 Secs Zee sadecccud da
9. cdsedseandeaucsacd Zoccecacd Sued eandescuqaaa tad sida uucddacdeadecnadece R 10 GONTROL PANEL LOCKING 2 dandaandecccucad Saud sdacaduccdaaduadeasccdcuscdsaveucdaccacSusaasuaseande 11 GOOKING ADVICE sie eee EN Se ee i oe eS 12 EXAMPLES OF COOKING POWER SETTING nn nn nn an nn nn ennenen nnmnnn a 12 MAINTENANCE AND 12 WHAT TO DO IN CASE OF A PROBLEM 13 ENVIRONMENT PRESERVA TON iaa 13 INSTAEEATION INSTRUGTIONS a a es 14 ELECTRICAL CONNECTION 15 SAFETY Precautions before using Unpack all the materials The installation and connection of the appliance must be done by a qualified electrician The manufacturer can not be responsible for damage caused by building in or connection errors The appliance must be installed in proper worktop This domestic appliance is exclusively for the cooking of food to the exclusion of any other domestic commercial or industrial use Remove all labels and self adhesives from the ceramic glass Do not change or alter the appliance The cooking plate can not be used as a working surface The appliance must be grounded and connected conforming to local standards Do not use an extension cable to connect i
10. cooking collection Instructions for use and warranty details Ceramic Cooktop Model No CCT6010 CCT8010 Dear Customer Thank you and congratulations for choosing Kleenmaid Your new appliance has been designed and meticulously tested to ensure that it meets all your Culinary requirements and has been carefully manufactured using top quality materials to give you years of reliable performance For best results carefully read the instructions on how your new appliance is to be installed Correct installation will avoid delays and unnecessary service call costs Once installation is complete please read this instruction manual carefully and get to know the controls and the features of your new Kleenmaid appliance These simple instructions will enable you to achieve excellent results from the very first time you use it Again congratulations and thank you for choosing The Best You Can Own KLEENMAID SUMMARY A Sainte 4 PRECAUTIONS BEFORE 4 USING THE APPLIANCE 4 PRECAUTIONS NOT TO DAMAGE THE APPLIANCE sssccesesecccsssseeseuececeansaseeeueeuaeaeansaseseeueneuansasesesueeaeagannsesesuaeanannseseenans 5
11. ctrician perfectly to the fact of the normative regulations and which respects them scrupulously e Protection against the parts under tension must be ensured after the building in e The data of connection necessary are on the stickers place on the hob casing near the connection box connection to the main must be made using an earthed plug or an omnipolar circuit breaking device with a contact opening of at least 3 mm e The electrical circuit must be separated from the network by adapted devices for example circuit breakers fuses or contactors e If the appliance is not fitted with an accessible plug disconnecting means must be incorporated the fixed installation in accordance with the installation regulations e The inlet hose must be positioned so that it does not touch any of the hot parts of the hob or oven Caution This appliance must only be connected to a network 230 V 50 Hz Always connect the earth wire Respect the connection diagram The connection box is located underneath at the back of the hob casing To open the cover use a medium screwdriver Place it in the slits and open the cover Mains Connection Cable diameter Cable Protection calibre 05 230V 1P N 50Hz 1 Phase 3 x 2 5 mm H05RR EF 25A 05 VV 400V 2P N 50Hz 2 Phases N 4x 1 5 mm 16 A calculated with the simultaneous factor following the standard EN 60 335 2
12. display 00 Automatic stop at the end of the cooking time As soon as the selected cooking time is finished the timer display will blink 00 and a sound rings To stop the sound and the blinking press the key 00 e Egg timer function Example for 29 minutes Action Activate the hob Select Timer Set the units Validate the units Set the tens Validate the tens Control panel Press display 0 Press display CL Slide on the SLIDER to 9 Press display 09 Slide on the SLIDER to 2 Press display 29 After a few seconds the control light stops blinking As soon as the selected cooking time is finished the timer display will blink 00 and a sound will be heard To stop the sound and the blinking press the display 00 The hob switches off Display 0 and control light on 7 00 O fixed 6 blinking O blinking 6 fixed 1 blinking 6 fixed 16 Display 0 and control light on 13 1 fixed 0 blinking 1 blinking O fixed O blinking O fixed 00 Display Zone control lights are on 00 O fixed 9 blinking O blinking 9 fixed 2 blinking 9 fixed 29 Automatic cooking All the cooking zones are equipped with an automatic go and stop cooking function The cooking zone starts at full power for a certain time then reduces automatically its power to the pre selected level e S
13. e heating zones may be touched safely As long as the residual heat indicators are on don t touch the heating zones and don t put any heat sensitive object on them There are risks of burn and fire Extension zone Action Control panel Display select zone Press display 0 Control light is blinking Select the power level Slide on the SLIDER O to 9 Switch off Touch key Extension zone light is off Switch on Touch key Extension zone light is on Timer The timer can be used simultaneous with all 4 heating zones and with different time settings from O to 99 minutes for each heating zone e Setting and modification of the cooking time Example for 16 minutes at power 7 Action Zone selection Select the power level Select Timer Set the units Validate the units Set the tens Validate the tens Control panel Press display 0 Slide on the SLIDER to 7 Press display CL Slide on the SLIDER to 6 Press display 06 Slide on the SLIDER 1 Press display 16 The time is confirmed and the cooking starts e To stop the cooking time Example for 13 minutes at power 7 Action Zone selection Select Timer Deactivate the units Validate the units Deactivate the tens Validate the tens Control panel Press display O selected Press key 13 Slide on the SLIDER to 0 Press display 10 Slide on the SLIDER to 0 Press
14. e service costs in full Model Number Date of purchase For service assistance visit www kleenmaidhelp com au Other products available in the Kleenmaid range of appliances Washing machines Clothes dryers Dishwashers Ovens Cooktops Steam ovens Microwave ovens Built in espresso coffee machines Rangehoods Freestanding ovens Compass Capital Services Pty Limited trading as Kleenmaid ABN 96188214525 Level 2 204 Botany Road Alexandria NSW 2015 E help kmaid com au www kleenmaid appliances com au KLEENMAIC
15. ed immediately You will thus prevent the surface being damaged 12 WHAT TO DO IN CASE OF A PROBLEM The hob or the cooking zone doesn t start up The connection to the network is wrong The protection fuse has disconnected The locking function is activated The sensitive keys are covered with grease or water An object is put on a key The control panel displays e The electronic system is defective e Disconnect and reconnect the hob at the circuit breaker The control panel displays 4x L e Refer to the chapter control panel locking page One or all cooking zone cut off The safety system is activated You forgot to turn off the cooking zone for a long time One or more sensitive keys are covered The pan is empty and its bottom overheated The hob also has an automatic reduction of power level to prevent overheating The automatic cooking system doesn t start up e The cooking zone is still hot H e The highest power level is set 9 The control panel displays U e Refer to the chapter Keep warm The control panel displays 11 e Refer to the chapter Pause ENVIRONMENT PRESERVATION e The materials of packing are ecological and recyclable e The electronic appliances are composed of recyclable and sometimes harmful materials for the environment but necessary to the proper operation and the safety of the appliance Don t throw your appliance into the household rubbish e Get in
16. he cooking zone The bottom of the pan should cover as much as possible the cooking zone Do not place aluminium or synthetic material containers on the hob they could melt on residual hot cooking zones e NEVER try to extinguish a fire with water but switch off the appliance and then cover flame e g with a lid or a fire blanket DESCRIPTION OF THE APPLIANCE Technical characteristic Type Total Power Position of the heating zone Nominal Power Diameter Front left 1000 2200 W 135 210 mm Rear left 1200 W 145 mm sera TROUW Rear right 1500 2400 W 170 x 265 mm Front right 1200 W 145 mm Front left 1000 2200 W 135 210 mm Rear left 1200 W 145 mm CCT8010 10004 Rear right 1500 2400 W 170 x 265 mm Front right 1800 W 180 mm Control panel gi Ls aa lt gt O Power display Control light extension Control light On Off 0 1 On Off key setting zone USE OF THE APPLIANCE Sensitive touch Your ceramic hob is equipped with electronic controls with sensitive touch keys When your finger presses the key the corresponding command is activated This activation is validated by a control light a letter or a number in the display and or a beep sound For normal use press only one key at any time Display Display Designation Function 0 Zero The heating zone is activated 1 9 Power level Selection of the cooking level A Heat accelerator Automatic cooking
17. of this Kleenmaid appliance Compass Capital Services trading as Kleenmaid guarantee that any fault caused by defective material or workmanship becoming apparent will be rectified free of charge with reference to parts and labour provided that all service is performed during normal working hours by Kleenmaid or their designated Agents Where the appliance is installed outside the normal servicing area of the above the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent s travel cost to and from the purchaser s home Commercial Warranty One year warranty When this appliance is installed in a commercial application in addition to all statutory rights which you the Purchaser have under relevant laws in respect of this appliance during the first one year of ownership as the original purchaser of this Kleenmaid appliance Compass Capital Services trading as Kleenmaid guarantee that any fault caused by defective material or workmanship becoming apparent will be rectified free of charge with reference to parts and labour provided that all service is performed during normal working hours by Kleenmaid or their designated Agents Where the appliance is installed outside the normal servicing area of the above the Purchaser must pay for the cost of transporting the appliance to and from the Agent or the Agent s travel cost to and from the purchaser s home What these warranties do not cover Compass Capi
18. t The appliance can not be used above a dishwasher or a tumble dryer steam may damage the electronic components The appliance is not intended to be operated by means of external timer or separate remote control system Using the appliance Switch the heating zones off after using Keep an eye on cooking using grease or oils they may quickly ignite Be careful not to burn yourself while or after using the appliance Make sure no cable of any fixed or moving appliance contacts with the glass or the hot saucepan Never cover the appliance with a cloth or a protection sheet This may become very hot and catch fire e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance e This appliance is not intended to be operated by means of an external timer or separate remote control system Precautions not to damage the appliance e Unfinished pan bottoms or damaged saucepans non enamelled cast iron pots may damage the ceramic glass e Sand or other abrasive materials may damage ceramic glass e Avoid dropping objects even small ones on the vitroceramic glass Do not hit the edges of the glass with saucepans e
19. tal Services trading as Kleenmaid is not responsible for any damage or malfunction unless caused by a defect in material or workmanship This includes but is not limited to abuse misuse improper installation and transportation damage Compass Capital Services trading as Kleenmaid is not responsible for consequential damages from any malfunction This warranty does not cover wear or breakage of consumable items such as door seals replacement of light globes or glass breakage due to impact In case of fractured glass do not use your appliance Purchaser s responsibility The Purchaser must make the appliance available for servicing and shall bear any costs incurred for any de installation and or re installation required to make the appliance available for servicing Compass Capital Services trading as Kleenmaid is not liable for any consequential damage incurred during de installation or re installation Warranty registration and Proof of Purchase Please complete warranty details below and retain together with your proof of purchase document When requesting service under this warranty the Purchaser agrees that Proof of Purchase of their Kleenmaid appliance will be necessary in order to make the warranty valid Inability to provide Proof of Purchase even though this warranty is in place will not bind Compass Capital Services trading as Kleenmaid to repair the appliance at no charge under this warranty and will require the Purchaser to pay for th
20. tart up Action Control panel Display Zone selection Press display O selected 0 and control light on Full power setting Slide on the SLIDER to 9 Pass from 0 to 9 Automatic cooking Re press on display 9 9 is blinking with A Select Power level Slide on the SLIDER to 7 9 passto 8 7 for example 7 7 is blinking with A e Switching off the automatic cooking Action Control panel Display Zone selection Press 7 from the zone 7 blinking with Power level selection Slide on the SLIDER 1 to 9 Pause function This function stops the entire hob s cooking activity and allows restarting with the same settings Startup stop the pause function Action Control panel Display Engage pause Press Il key Displays II in the for 2 seconds Heating zone displays Stop the pause Press II key for 2 seconds Pause control light is blinking Press or Slide on the SLIDER Pause control light is off Recall Function After switching off the hob 0 1 it is possible to recall the last settings Cooking stages of all cooking zones power minutes and seconds of programmed cooking zone related timers switching condition of the concentric zone small or big diameter Heat up function Keep warm function The recall procedure is following Press the key 0 1 Then press the key II within 6 seconds The previous settings are activated Keep
Download Pdf Manuals
Related Search