UpMix - DaySequerra
Contents
1. DaySequerra dts Neural Surround UpMix Quick Start Guide JaySequerra nea Loos AES ERROR FAULT UpMix 7 1 MODE This guide offers the quickest way to install and begin using your new UpMix Surround Audio Decoder While UpMix s default settings are found to work in most applications please read through the documentation to ensure you are getting the best experience from UpMix The full owner s manual may be downloaded off our website at www daysequerra com While you are there please take a few moments to complete the warranty registration form 1 Mount the unit into your rack or place on a stable surface 2 Connect your BNC AES input cables and output cables 3 Connect UpMix to a power source with the supplied cables UpMix will automatically power up when AC power is applied 4 Rotate the knob to enter the menu Press ENTER to select SYSTEM MENU Press ENTER to select I O 5 Define input mode The default setting is STEREO Other input options may be selected based upon your configuration Press ENTER and scroll the wheel to see available choices Press ENTER to confirm a selected choice 6 Define output mode The default setting is 5 1 Other output options may be selected based upon your configuration Scroll the wheel two clicks to select OUTPUT MODE and then press ENTER to make your choice 7 Define your clock source The default setting is AES input 1 2 Other options may be selected based upon your conf2. Two 750 BNC connectors that allow UpMix to receive an AES REF or DARS clock signal from an external source and pass it on to other devices in the same stack The AES 3id 1995 SMPTE 276M standard dictates a 75Q unbalanced connection and requires proper termination The termination should occur at the destination of the signal that is on the inputs to UpMix If the loop through BNC connectors are not feeding additional equipment terminate each of these with a standard 75Q terminator Like other inputs AES SYNC signal should be terminated GPIO A Female DB 9 connection that allows UpMix to be monitored or controlled externally Opto isolated inputs will be triggered by a voltage of 5VDC Output Relay 1 N O Relay 1 Common Optical Input 0 Optical Input 1 Optical Input Common Output Relay 2 N O Relay 2 Common Optical Input 2 Optical Input 3 DB 9 Female Port on UpMix Rear Panel OO INI OD oO AJOIN Output 1 Relay 1 is Normally Open Upon a hardware failure i e Power Supply or Internal Communications Failure the relay will close When the failure is remedied the relay will open Output 2 Relay 2 is Normally Open Upon an AES lock loss failure this relay will close When the failure is remedied the relay will open DaySequerra UpMix User Manual Input 1 Voltage detected on this input will cause UpMix to go into pass though operating mode Input 2 Voltage detected on this
3. UpMix will revert to its previous state To enter the programming menu turn the selection knob in any direction while at the HOME screen The ENTER key will enter the currently selected sub menu or enter the value selection mode for the option A press of the BACK key will navigate to the previous menu level or revert the current value to its last stored state DaySequerra UpMix User Manual Menu Tree Home Screen SYSTEM MENU NO Input Mode Stereo Input Output Mode LFE Clock Source Sync Source SETTINGS Surround Width Input UR Gain Surround Depth Center Mode LFE Cutoff Output UR Gain Output Limiter Output LFE Gain NETWORK Device Name DHCP f IP ae MAC Address Output Ls Rs Gain DIAGNOSTICS Current Faults DSP Utilization Output Lb Rb Gain LED Test Meter Brightness Display Brightness Restore Settings GPIO Test Output 1 Output 2 ALARMS ee AES Lock Input 1 PSU Alert input 2 ABOUT Model Number Serial Number Hardware Rev Firmware Rev DTS Algorithm DTS Algorithm Rev Figure 3 Visual Map of UpMix Menu System 12 DaySequerra UpMix User Manual Menu Functions and Descriptions Figure 4 Main Menu display on the DaySequerra UpMix The Display output shown on UpMix when you first enter the menu is shown in Figure 4 From here you can navigate to the rest of the menu by selecting SYSTEM MENU or you can adjust the audio levels for the following audio channels 12 to 12dB and mute Input L R Gain Two channe
4. input will have UpMix take the input signal and up mix it into 5 1 surround Input 3 Unused Input 4 Unused NETWORK Used to update UpMix s firmware To connect directly to a PC without use of a network switch or hub a crossover cable is required Firmware updating is accomplished via UDP Port 44600 PSU 1 PSU 2 Two IEC320 ports to connect to AC Mains The internal power supplies are auto switching and will work on 120VAC 60Hz or 240VAC 50Hz electrical power systems with a maximum total current draw of 25W gt 25A 120VAC or gt 15A 240VAC Please connect UpMix to a properly grounded uninterruptible power supply UPS to protect against power surges and low voltage conditions For maximum redundancy connect each power supply to a separate UPS on different power circuits UpMix may be combined with other devices on the output of the UPS es as long as the total load is within the UPS capacity Consult your UPS manual for details Meter Display 60 60 60 60 60 N L Rm C LFE Ls en R7 N L R C LFE Ls Re 60 Figure 1 Metering display UpMix INPUT LEVELS LED display shows current amplitude of input signal from 60dB to OdB across all active channels Unused channels will not light the display L Left AES Input 1 LFE Low Frequency AES Input 4 R Right AES Input 2 Ls Left Surround AES Input 5 C Center AES Input 3 Rs Right Surround AES Input 6 OUTPU
5. or attributable to acts of God abuse accident misuse improper or abnormal usage failure to follow instructions improper installation or maintenance alteration or lightning power fluctuations and other incidental or environmental conditions Further product malfunction or deterioration due to normal wear is not covered by this warranty DAYSEQUERRA DISCLAIMS ANY WARRANTIES EXPRESSED OR IMPLIED WHETHER OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE EXCEPT AS EXPRESSLY SET FORTH HEREIN THE SOLE OBLIGATION OF DAYSEQUERRA UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED PRODUCT IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN DAYSEQUERRA EXPRESSLY DISCLAIMS ANY LOST PROFITS GENERAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM BREACH OF ANY WARRANTY OR ARISING OUT OF THE USE OR INABILITY TO USE ANY DAYSEQUERRA PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state DaySequerra reserves the right to modify or discontinue without prior notice to you any model or style product If warranty problems arise or if you need assistance in using your product contact DaySequerra 154 Cooper Road Building 902 West Berlin NJ 08091 85
6. 6 719 9900 phone 856 719 9903 fax For more information please visit www daysequerra com or email us at support daysequerra com DaySequerra 154 Cooper Rd 902 West Berlin NJ 08091 Voice 856 719 9900 Facsimile 856 719 9903 www daysequerra com Manufactured under license from DTS Licensing Limited DTS and the Symbol are registered trademarks and the DTS logo is a trademark of DTS Inc Product includes software DTS Inc All Rights Reserved
7. T LEVELS LED display shows current amplitude of signal generated by UpMix across all active channels Unused channels will not light the display L Left AES Output 1 LFE Low Frequency AES Output 4 R Right AES Output 2 Ls Left Surround AES Output 5 C Center AES Output 3 Rs Right Surround AES Output 6 Items in italics are only utilized when UpMix is configured to take a 5 1 audio stream and create a 7 1 audio stream 4 DaySequerra UpMix User Manual Home Screen Figure 2 Home Screen on UpMix When you power on UpMix if there are no errors the display should look similar to the one pictured above Each field is dynamic and will show status or current selected settings 1 Currently selected surround width Located on SETTINGS menu May also display current fault status over fields 1 and 2 Currently selected surround depth Located on SETTINGS menu May also display current fault status over fields 1 and 2 Current clock sync UpMix is operating with This clock is either internal or externally acquired Current output mode This is selectable on the I O menu Input source port will display the port number UpMix is set to receive the audio stream from This can be set under the I O menu Clock source display will indicate where UpMix is getting a clock signal This will be represented as a port number internal or external Programming Menu If AC line power is lost or momentarily interrupted
8. choices of letters A Z 0 9 and _ underscore and press enter to move on to the next field Turning the knob again will start to scroll through the choices for the next letter or pressing ENTER accepts the name DHCP Configures UpMix to look for a DHCP server for IP configuration Enabled or Disabled IP Address If DHCP is set to disabled allows you to enter the desired IP address manually Press ENTER while the cursor is over this field to go into data entry mode Scroll through the available numbers 0 255 and press ENTER to move to the next octet MAC Address Displays UpMix s MAC address if needed for firewalls or DHCP IP address assignments Diagnostics Menu Current Faults Displays any error states that UpMix may be in DSP Utilization Shows the current load on UpMix s processor LED Test Turns on all front panel LED indicators to verify their functionality Meter Brightness Allows adjustment of UpMix s Input and Output meters intensity Display Brightness Allows adjustment of UpMix s display output intensity Restore Settings Returns all settings to their factory default values and reboots the unit Network settings will not be lost GPIO Test A sub menu that can turn on the GPIO outputs for testing and shows the current state of the GPIO inputs Alarms Menu AES Lock Allows the AES Lock alarm to be suppressed PSU Alarm Allows the Power Supply alarm to be suppressed DaySequerra UpMix User Manual Abo
9. ective 73 23 EEC and EMC Directive 89 336 EEC CE Mark EN 55022 Class A EN55024 Designed for ROHS and WEEE compliance FCC Part 15 Regulatory Statement This equipment has been tested and found to comply with the limits for Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction s manual may cause interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at their own expense The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user s authority to operate this equipment The user should use only shielded and or grounded cables to combat sources of interference Environmental Preservation Efforts This equipment has been designed and built by DaySequerra corporation to give many years of trouble free service and is backed by our three year warranty and commitment of providing the best customer support When the time comes to retire your product from service it should be disposed of in accordance with local codes or ordinances Do not discard with household or c
10. er and later combined video to have a complete HD broadcast DaySequerra UpMix User Manual Installation Immediately upon receiving your UpMix please make a careful inspection for any shipping damage If damage is found or suspected please notify the carrier at once and then contact your dealer UpMix is shipped in one carton which contains the UpMix unit an AC power cable and this Users Manual We strongly encourage you to save the shipping carton and shipping materials supplied with your UpMix They are specially designed to properly protect your UpMix and in the event that you need to return it for service only these OEM shipping materials can ensure its safe return to our factory We provide a limited 3 year warranty on all of our products however if you don t register your unit it is impossible for us to contact you to notify you when important software upgrades become available Please take a few minutes to complete the warranty registration form on our website www daysequerra com Rack Mount Installation The UpMix chassis has four rack mounting holes and has been designed to fit in a standard 1RU space Plastic finishing washers are recommended to protect the painted surface around the mounting holes Locate the air vents on each side of the unit and be sure to keep them clear so the unit may have adequate ventilation Power Connection The AC power cable supplied with UpMix must be connected from the IEC320 po
11. iguration select EXTERNAL if you are using the AES SYNC ports or select INTERNAL if you wish to use UpMix s internal clock 8 Press HOME to return to the home screen If errors are displayed consult your user s manual for further details ns LEVELS OO OUTPUT LEVELS 7 STATUS r F 6 o f o 0 Si Rc LFE ts is NL Rc LFE RI I Front Panel Features INPUT LEVELS Displays audio level of the inbound audio stream OUTPUT LEVELS Displays audio level of the up mixed audio stream AES LOCK Green LED illuminates when a valid AES3 digital input signal has been acquired AES ERROR Red LED illuminates when the AES3 digital input signal is lost or received corrupted FAULT Red LED illuminates when a fault has been discovered 7 1 MODE Blue LED indicates when operating in 7 1 channel input mode VACUUM FLORESCENT DISPLAY Displays current operating status of the unit and programming menus SELECTION KNOB Used to select values while in the menu system ENTER KEY Used to enter a menu or confirm a selection HOME KEY Will return you to the home screen BACK KEY Will return you to a previous menu DaySequerra 154 Cooper Road Building 902 West Berlin NJ 08091 856 719 9900 sales daysequerra com www daysequerra com aySequerra dts Menu Tree Home Screen SYSTEM MENU Input UR Gain Output UR Gain Output LFE Gain Output C Gai
12. ing spatial location and distortion The conveniences of a matrix surround encode decode system with the performance of modern day perceptual audio codecs All rights reserved DaySequerra Corporation Copyright 2009 All logos and trademark used herein are the property of their respective owners DaySequerra Specifications subject to change UpMix User Manual Revision A1 UpMix User Manual Important Safety Information Indoor use only Not for use in wet or damp environments Maximum Relative Humidity lt 80 Class Equipment grounded type Electrical rating 100 260V 50 60Hz 25W max AC Mains supply voltage fluctuations are not to exceed 10 of the nominal voltage Operations temperature range 40 C to 70 C Maximum altitude 3000m 9843ft Equipment suitable for continuous operation Weight 3 6kg 8 0lbs equipment only 5 4kg 12 0lbs shipping Important Note Please connect your UpMix to an uninterruptible power supply UPS to provide other protection against power surges and low voltage conditions Service Information The DaySequerra UpMix contains no user serviceable components inside the unit Please contact DaySequerra for repair and upgrade information In the event that your unit needs to be returned to the factory contact us for a return authorization number Please visit www daysequerra com and register your new UpMix so we can keep you informed of the latest hardware and software updates The lightning flash wi
13. l Input 2 9 Optical Input 3 1 Output Relay 1 N O 2 Relay 1 Common 3 Optical Input 0 4 Optical Input 1 5 Optical Input Common NETWORK Used to update UpMix s firmware To download the complete user manual please go to www dayequerra com WWW dayS QUEFTA COM MADE 1S THE USA OAFEQUENUHA A REQUIRED TRADEMARK OF DAYSEQUERRA COM Fe ce GPIO amg 7 A NETWORK hu A sales daysequerra com 856 719 9900 www daysequerra com DaySequerra Neural Surround 5 1 Surround Decoder UpMix User Manual Welcome Thanks for purchasing the DaySequerra UpMix Our UpMix transforms any stereo signal into a surround sound experience by utilizing the DTS Neural Surround process We design and build all of our DaySequerra products to be completely reliable and easy to use so you can concentrate on producing great sounding broadcasts not struggling with complicated equipment or difficult to use product manuals While the UpMix has been designed to be straightforward to use we do suggest that you spend a few minutes familiarizing yourself with the features and operational functions that are contained in this manual DaySequerra has been building broadcast quality products since 1989 The technology developed for the UpMix and all of our products has evolved through a process of user feedback extensive listening field testing and careful refinement In the event that you encounter any technical or opera
14. l stereo input level Output L R Gain Left Front and Right Front output level Output LFE Gain Low Frequency Effects output level Output C Gain Center channel output level Output Ls Rs Gain Left Surround and Right Surround output level Output Lb Rb Gain Left Back and Right Back output level Only the options that are available for the current configuration will be displayed System Menu Figure 5 System Menu screen display on the DaySequerra UpMix Navigating to SYSTEM MENU after entering the Main Menu will allow you to change all values to fine tune the operation of your UpMix O Menu Figure 6 I O Menu screen display on the DaySequerra UpMix DaySequerra UpMix User Manual The I O Menu will allow you to tailor UpMix to your specific application Input Mode Defines what kind of signal UpMix is going to process Stereo Stereo Input Defines what physical BNC port UpMix will receive the stereo audio input stream 1 2 3 4 5 6 Output Mode Defines what output signal format UpMix will generate Bypass Stereo 2 1 3 1 4 1 5 1 6 1 or 7 1 LFE Defines how UpMix will treat Low Frequency Effects Normal or Mute Clock Source Defines where UpMix gets the timing signal Internal UpMix s Internal Clock Define using Sync Source Ext Sync UpMix will get timing from AES Sync Port 1 2 UpMix will get timing from the 1 2 BNC Input 3 4 UpMix will get timing from the 3 4 BNC Input 5 6 UpMix will get
15. n Output LsRs Gain Output Lb Rb Gain D gt Pa 1 2 gt 34 s lt m NETWORK v lt Neural Technologies UpMix Quick Start Guide VO Input Mode Stereo Input H Output Mode LFE Clock Source Sync Source SETTINGS r Surround Width Surround Depth Center Mode LFE Cutoff Output Limiter Device Name DHCP IP MAC Address DIAGNOSTICS Current Faults DSP Utilization LED Test Meter Brightness Display Brightness Restore Settings GPIO Test AES Lock PSU Alert ALARMS ABOUT Serial Number Hardware Rev Firmware Rev DTS Algorithm IN DaySequerra THRU lt Aes nPuTs AEs ouTpuTs aes sync DaySequerra 154 Cooper Road Building 902 West Berlin NJ 08091 Model Number DTS Algorithm Rev UPMIX SURROUND DECODER GMMI Rear Panel Features AES INPUTS Three 75Q BNC connectors will accept an AES3 digital audio stream AES OUTPUTS Four 75Q BNC connectors output the up mixed AES3 digital audio stream AES SYNC Two 750 BNC connectors that allow UpMix to receive an AES REF or DARS clock signal from an external source and pass it on to other devices in the same stack GPIO A Female DB 9 connection that allows UpMix to be monitored or controlled externally Opto isolated inputs will be triggered by a voltage of 5VDC 6 Output Relay 2 N O 7 Relay 2 Common 8 Optica
16. nsport solution Surround content that has been encoded by UpMix will be reproduced just as it was heard in the original 5 1 mix To improve system reliability and up time UpMix uses a robust DSP based processing platform rather than the PC based approach to completely avoid broadcast disruptions caused by operating system lockups Operational Diagram The diagram below shows an UpMix taking a two channel audio source such as stereo matrix encoded stereo or LtRt and creating a 5 1 channel surround mix using the proprietary DTS Neural Audio process Monitor or Distribution System 2 Channel DaySequerra Audio Source UpMix Stereo 5 1 Surround The surround mix produced from the input content is fully immersive to the listener when played through a 5 1 monitor system Typical Applications Here are some examples that describe some typical applications where you might use UpMix RADIO PRODUCTION STUDIO UpMix allows production engineers to render mono or stereo content into surround The mix can then be broadcasted on a compatible medium When used in conjunction with DownMix UpMix will allow the engineer to render a watermarked Lw Rw two channel audio source back into its original surround content STEREO TELEVISION MASTER CONTROL Another application of UpMix is in a stereo television master control room setup UpMix allows rendering of original mono or stereo content into surround The surround mix can then be sent to an encod
17. ntrol Panel then Network Connections Right click on the adapter to be disabled and select Disable 3 Unplug your PC from the network it is currently connected to 4 If your PC s network interface is set up for DHCP disable it and enter a static IP address While in Network Connections under Control Panel right click on the network interface and select Properties Select Internet Protocol TCP IP and press the Properties button On the general tab of the dialogue box select Use the following IP address Enter an IP address in the box IP Address within the local network range Example 192 168 0 1 Click in the Subnet mask box and it should auto populate with 255 255 255 0 Select OK to close the dialog and then OK to close the properties box 5 If UpMix is set up for DHCP disable it and enter a static IP address within the local network range Example 192 168 0 2 Details are available in the NETWORK section of this manual 6 Connect the UpMix to the PC using a crossover Ethernet cable 7 When Windows has acknowledged the Ethernet connection you may start the update progress by double clicking on upgrade bat UpMix should download the new firmware and reboot within 15 seconds 8 Disconnect the cross over cable and return your PC and UpMix to their original networking configurations DaySequerra UpMix User Manual 13 DaySequerra UpMix User Manual DaySequerra Three Year Limited Warranty DaySeque
18. ommercial waste DaySequerra products are manufactured with the environment in mind The Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment 2002 95 EC restricts the use of six specific hazardous materials in the manufacture of various types of electronic and electrical equipment Following this directive prevents these toxic substances from entering our environment after disposal RoHS DaySequerra UpMix User Manual Introduction The DaySequerra UpMix renders any two channel audio source stereo matrix encoded stereo or LtRt as surround sound Because UpMix renders sound independently of the transport environment it will compliment analog digital linear or compressed mediums Using the DTS Neural Audio process UpMix can simultaneously position individual elements within a rich surround field creating unparalleled image stability and realistic granularity This approach avoids taking artistic license with content by placing audio exactly where it would be heard in a professional LEDE Live End Dead End listening environment For example mono or pan pot stereo will image in front of the listener on the center channel where stereo containing depth information will surround the listener using the full capabilities of their surround decoder UpMix can be used as a stand alone unit to monitor stereo production or in tandem with the DaySequerra DownMix as a complete 5 1 tra
19. ontain the announcement of new firmware issues corrected and instructions on how to retrieve the update files The updating process may only be performed on a PC platform Update packages will be available as a single ZIP file for download Compatible archive programs include Winzip www winzip com or WinRAR www rarlabs com and may be downloaded from their respective websites The update package will contain four files dsp2501 bin firmdown exe readme txt and update bat Firmware updating is accomplished via UDP Port 44600 At this time updating is only supported by using a cross over cable directly connected to one PC If your PC has multiple network interface adapters each additional adapter will need to be disabled before attempting to upgrade your unit You may also wish to disable your firewall during the upgrade process For additional support with networking please contact your network administrator DO NOT UNPLUG THE UNIT OR TURN OFF YOUR PC WHILE THE FLASH IS IN PROGRESS If the flash procedure is interrupted before it can complete UpMix may be left in an un usable state and will need to be returned for factory service Please follow these steps to upgrade your unit 1 Un Zip the files using a compatible utility that can handle ZIP archive file format into a new empty directory on your PC A password may be required in order to extract the files 2 Disable any additional network interface adapters present on your PC Go to Co
20. ost or has received an invalid AES3 digital input signal FAULT Red LED indicator illuminates when UpMix has discovered a fault The fault will be displayed on the home screen or may be viewed under the fy DIAGNOSTICS menu Fault text may be removed from the home screen by pressing the ENTER key 7 1 MODE 7 1 MODE Blue LED indicator illuminates when UpMix is producing a 7 1 channel stream Display and Controls VACUUM FLUORESCENT DISPLAY A Multi function display will indicate current operating status of the unit and programming menus SELECTION KNOB A stepping rotational knob is used to select values while in the menu system To enter the menu simply rotate the knob in any direction while UpMix is on the HOME screen ENTER KEY Used to enter a menu or confirm a selection This key will also clear a FAULT display from the home screen HOME KEY A press of this button will return UpMix to its home screen BACK KEY While on the HOME screen this key will re display the FAULT status text if it has been cleared A press of this key will return to a previous menu or if you are entering a value exit the field and return the value to the last programmed state DaySequerra UpMix User Manual Rear Panel mokono P UPMIX SURROUND DECODER o EA AES INPUTS Three 750 BNC connectors will accept an AES3 digital audio stream AES OUTPUTS Four 750 BNC connectors output the up mixed AES3 digital audio stream AES SYNC
21. rra warrants this product to be free from defects in materials and workmanship to its original owner for three 3 years from the date of purchase DaySequerra will repair or replace such product or part thereof that upon inspection by DaySequerra is found to be defective in materials or workmanship A Return Authorization Number must be obtained from DaySequerra in advance of return Call DaySequerra at 856 719 9900 to receive the number to display on the outside of your shipping carton A written statement with the name address and daytime telephone number of the original owner together with receipt from the original purchase and a brief description of any claimed defects must accompany all returns Parts or product for which replacement is made shall become the property of DaySequerra The customer shall be responsible for all costs of transportation and insurance to and from the DaySequerra factory and all such costs will be prepaid DaySequerra shall use reasonable efforts to repair or replace any product covered by this limited warranty within thirty days of receipt In the event repair or replacement shall require more than thirty days DaySequerra shall notify the customer accordingly DaySequerra reserves the right to replace any product that has been discontinued from its product line with a new product of comparable value and function This warranty shall be void in the event a covered product has been damaged or failure is caused by
22. th arrowhead symbol is intended to alert the user to the presence of un insulated dangerous voltages within the product s enclosure that may be of a sufficient level to cause harm The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance instructions within the product literature Exposed portions of the power supply assembly are electrically live To reduce risk of electric CAUTION TO REDUCE THE RISK OF shock the power cord must be disconnected when ELECTRIC SHOCK DO NOT REMOVE the power supply assembly is removed For COVER OR BACK NO USER continued protection against electric shock a SERVICEABLE PARTS INSIDE correctly wired and grounded earthed three pin en SERVICING TO GUALIFIED power outlet must be used Do not use a ground ICE PROFESSIONAL no lifting adapter and never cut the ground pin on the three prong plug The ground terminal of the power plug is connected directly to the chassis of the unit RISK OF ELECTRIC SHOCK A DO NOT OPEN DaySequerra UpMix User Manual Technical Specifications Latency of the DTS Algorithm 22ms at 48k sampling rate Power Consumption 25W Maximum Dimensions Rack Mount 1 RU 1 75 x 19 x 10 75 Dynamic Range 140dB DR any input to any output GPIO DB 9 Female 0 5V TTL Regulatory North America Designed to Comply with FCC Class A part 15 requirements Europe Designed to comply with LV Dir
23. timing from the 5 6 BNC Input Sync Source If Clock Source is set to internal defines what clock frequency UpMix will use 32 44 1 48 0 88 1 or 96 kHz Settings Menu Figure 7 Settings menu on the DaySequerra UpMix Settings that can be controlled on UpMix Rear Surround Width Adjusts the perceived width of the rear channel signal that is rendered from the stereo mix Narrow 05 95 Wide in 05 Increments Surround Depth Adjust the perceived depth of the entire surround signal that is rendered from the stereo mix 1 00 to 1 00 in 05 Increments Center Mode Tells UpMix to use a discreet center channel Hard Center or mix the center into the left and right channels Phantom LFE Cutoff Adjusts low pass filter for Low Frequency Effects 0 140Hz in 20Hz Increments Output Limiter Allows UpMix to reduce the level of the output stream OdB to 20dB 4 DaySequerra UpMix User Manual Network Menu The DaySequerra UpMix has several configurable network settings All of UpMix s network settings are password protected The password to change the network settings is upmix123 Please take note when entering the password that the UpMix password is case sensitive The DaySequerra UpMix is configured to take a DHCP address by default Device Name Allows you to change UpMix s name as reported to DNS Press ENTER while the cursor is over this field to go into data entry mode Turn the knob to scroll through the available
24. tional difficulties with this or any DaySequerra product please feel free to contact us at 856 719 9900 Our office hours are from 9 to 5 ET Monday through Friday Or you can email your questions to info daysequerra com Also please remember to visit our website www daysequerra com for warranty registration and the latest DaySequerra product information We have worked hard to ensure that your DaySequerra UpMix will reliably serve you for years to come With a modular design and upgradable firmware your new unit is easy to install and use right out of the box We sincerely hope our products help you achieve a new level of excellence in your work Dv David V Day and the DaySequerra Team DaySequerra 154 Cooper Rd 902 West Berlin NJ 08091 Voice 856 719 9900 Facsimile 856 719 9903 www daysequerra com Table of Contents Important Safety Information 4 Service Information 4 Technical Specifications 5 Introduction 6 Operational Diagram 6 Typical Applications 6 Unpacking and Installation 7 Front Panel Controls and Indicators 8 Rear Panel 9 Meter Display 10 Home Screen 11 Programming Menu 11 Menu Tree 12 Menu Functions and Descriptions 13 Faults 16 Firmware Update 17 Warranty 19 UpMix Key Features Perfect mapping of watermarked LtRt elements into the surround field Brings the excitement of surround sound to your audience without replacing any infrastructure Active correction to fix issues such as comb filter
25. ut Menu Model Number Displays the model number of the unit Serial Number Displays the serial number of this unit Hardware Rev Displays the hardware revision level of this unit Firmware Rev Displays the firmware revision level that is running on this unit DTS Algorithm Displays the specific DTS algorithm running DTS Algorithm Rev Version of the DTS algorithm running on this unit Faults Although your UpMix will provide you with years of trouble free service occasionally problems may occur Below is a listing of the most common fault conditions PSU x Failed One of the redundant power supplies has failed and your unit requires service Please contact DaySequerra to arrange for repair No Sync AES sync has been lost Please check the source equipment and all cable connections Ensure that UpMix is operating in the proper input mode for your application and is looking for the source audio on the correct port CRC Error UpMix has encountered a CRC error in the audio stream Validity Error UpMix has encountered a validity error with the audio stream Bi phase Error UpMix has encountered a bi phase error with the audio stream No Parity Error UpMix has encountered a parity error with the audio stream 4 DaySequerra UpMix User Manual Firmware Update Provided that you have completed warranty registration for your UpMix on our website we will notify you as new firmware updates become available The notification will c
26. wer entry module to an AC mains outlet with a functional earth ground connection For protection against electric shock and electro magnetic interference do not plug the power cable into a ground lifting adapter or remove the cable s grounding pin If in doubt please consult a qualified electrician UpMix is designed with redundancy in mind with two internal auto switching power supplies Please connect UpMix to an uninterruptible power supply UPS to protect against power surges and low voltage conditions For maximum redundancy connect each power supply to a separate UPS on different power circuits UpMix may be combined with other devices on the output of the UPS es as long as the total load is within the UPS capacity Consult your UPS manual for details UpMix will automatically power up when AC power is applied If AC line power is lost or momentarily interrupted UpMix will revert to its previous state DaySequerra UpMix User Manual Front Panel Meters INPUT LEVELS Six 10 segment multi colored LED meters display the audio level for each channel of the inbound audio stream OUTPUT LEVELS Six 10 segment multi colored LED meters display the audio level for each channel ofthe up mixed audio stream Status Indicators r STATUS y AES LOCK Green LED indicator illuminates when UpMix has acquired a valid AES3 digital input signal AES LOCK AES ERROR FAULT AES ERROR Red LED indicator illuminates when UpMix has l
Download Pdf Manuals
Related Search