H300 Manual
Contents
1. automatically switch itself off if overheated The amplifier will need some break in time before maximum sound quality can be experienced Never lift the H300 by holding around the volume knob or input selector knob The H300 is heavy and ap plying pressure may damage the knobs HEGE MUSIC SYSTEMS R cE www hegel com2. be muted and the right hand part of the display will flash for approximately 5 seconds indicating mute This is normal and is part of the start up procedure NOTE When the H300 has been switched off the amplifier should not be switched back on again before 30 seconds has passed Display The left hand part of the display normally shows the selected source input while the volume value Is shown in the right hand part of the display A flashing volume value indicates that the amplifier is in mute setting Source Selector The input source selector knob is on the left hand side of the front panel The three letters in the left hand part of the display will show the selected source input Volume The volume control knob is on the right hand side of the front panel and the volume level is indicated by a number between 0 and 99 in the right hand part of the display The H300 will power up with a preset vol ume value The volume level can be adjusted by turning the volume knob clockwise or counter clockwise or by using the RC8 remote control Mute When the mute button on the RC8 remote control is pressed the speaker outputs and Pre Out output are muted A flashing volume number in the display indicates that mute is on Press the mute button again to switch mute off Home Theater The Home Theater input is a fixed volume level input with the volume setting permanently set to a high volume value This input is available for connecting the H300
3. to a surround processor with internal adjustable volume Do not connect input sources such as CD players DVD players DACs or similar signal sources to the Home Theater input Connecting a fixed level signal source directly to the Home Theater input can cause severe damage to the amplifier and connected loudspeakers CONNECTIONS ircuit protected by JS Patent No 6 275 104 H300 Integrated Amplifier legel ay Rear side view of the H300 Integrated amplifier Always connect input output audio cables and power cable when the amplifier is powered OFF Connections from top left Speaker outputs Right channel Pre Out volume controlled preamp output Phono RCA left right Balanced signal input XLR left right input An1 input Phono RCA left right An2 input Phono RCA left right An3 input Phono RCA left right Home Theater input fixed high gain input Phono RCA left right Speaker outputs Left channel AC Power connection 230V 115V 100V AC dependent on country Fuse holder IR direct input Digital Output Coaxial RCA Coax1 Digital input Coaxial RCA Coax2 Digital input Coaxial RCA Optical1 Digital input TOSLINK EIAJ Optical Optical2 Digital input TOSLINK EIAJ Optical USB Computer input H300 has two types of analogue audio connnections unbalanced audio signal with RCA connectors Phono connectors and true balanced audio signal with XLR connectors pin 2 is positive phase pin 3
4. HEGEL MUSIC SYSTEMS Hegel H300 High End Integrated Amplifier User manual USER GUIDE Congratulations with your new HEGEL product All Hegel products are based on a si The audio reproduction instrument s mple philosophy hall reproduce the original musical sound purely and naturally It shall use Scandinavian design reflecting natural music reproduction and styling to fit in with any interior The products shall be easy to operate and shall be manufactured according to the best quality principles All HEGEL products are designed with acoustical instruments in a concert situation as the point of reference The music is reproduced exactly like the original and is limited only by the quality of the recording Our aim is to give you the best possible music experience SOUND ADVICE The Hegel H300 Integrated Amplifie r is easy to connect and operate and requires no prior technical knowl edge However to get the most out of the amplifier s superior sound and music quality we have provided a brief description of the connections and use of the amplifier in order to provide a total music experience We recommend keeping this user guide for future reference GENERAL USE On Off The H300 amplifier is switched on and off with the power button in the middle of the front panel When powered up the H300 will use 5 seconds to calibrate During this time the outputs will be muted NOTE When powered up the outputs will
5. ctions to avoid damaging the unit Be careful not to hold the volume and source knobs when lifting the amplifier Put the plastic bag around the amplifier Make sure that the plastic bag does not press tightly on the knobs as this may damage them during transportation Place the two bottom shock absorbers into the original cardboard box one in each end of the box Place the amplifier into the cardboard box fitting the shock absorbers Place the top shock absorbers on top of the amplifier Make sure the plastic bag is still loose around the volume and source knobs to avoid any damage to the knobs during transport Close the cardboard box using a suitable tape CLEANING Fingerprints or stains on the front panel or top cover can be removed with a cloth moistened with warm water or a mild detergent suitable for cleaning mirrors and windows TECHNICAL SPECIFICATIONS H300 Integrated Amplifier Power output 250W 250W in 8 Ohms Dual mono Minimum load 2 ohms Analog Inputs 1 balanced XLR 3 unbalanced RCA 1 Home Theatre RCA Digital Inputs 2 coaxial S PDIF 2 optical S PDIF 1 USB Line level Output Unbalanced Pre Out RCA Digital Output Coaxial S PDIF out digital inputs only Other Connections Direct IR in 3 5mm jack max 12V Frequency response 5Hz 180kHz Signal to noise ratio More than 100dB Crosstalk Less than 100dB Distortion Less than 0 01 100W 8 Ohms 1kHz Intermodulation Less than 0 01 19kHz 20kH
6. is negative phase and pin 1 is chassis earth REMOTE CONTROL RC8 The Hegel H300 can be operated from the included Hegel system remote control RC8 Like other Hegel products the number of buttons on the RC8 is kept to a minimum The Hegel system remote control will also control other Hegel products like CD players DACs and pream plifiers avoiding the need for several different remote control devices Remote control buttons starting top left 1 Skip to previous track on most computers media players ands 2 Play Pause on most computers media players 0 0 60 3 Skip to next track on most computers media players 299 4 Input source selector button for Hegel DACs 2 2 Q 5 ECO will put certain Hegel equipment in low power mode SSE 6 Display on off hold for off ON T Skip to previous track on Hegel CD players 8 Play Pause for Hegel CD players 9 Skip to next track on Hegel CD players 10 Switches up to next input on your Hegel amplifier 11 Stop Eject for Hegel CD players 12 Volume up for Hegel amplifiers 13 Switches down to previous input on your Hegel amplifier 14 Mute for Hegel amplifiers 15 Volume down for Hegel amplifiers The remote control uses two standard 1 5 volt LRO3 AAA batteries To insert the batteries please use a normal type cross head screwdriver to gently remove the four screws in the bottom of the remote control Do not use a Pozidrive cross head screwdriver it may damage the head of the
7. screws Be sure to insert the batteries with the correct polarity with sign and sign as shown inside the battery holder Be careful when inserting the screws after fitting the batteries Please turn the screws gently by hand first to avoid damaging the threads in the remote control body Do not tighten the screws to hard as this may damage the screws and the soft metal body of the remote control Please do not drop the remote control down on the floor or any hard surface as this may damage internal parts of the remote control To avoid damage to the remote control by leakage from the batteries during transport and storage the remote control is supplied without batteries from Hegel SPECIAL FUNCTIONS Display On Off The DISP button on the RC8 remote control may be used to turn the display of the H300 on or off Holding the DISP button for more than 1 seconds will turn the display off while giving the button a shorter push will turn the display on DAC loop This function makes it possible to upgrade the digital inputs of the H300 with an external high end DAC This is done by connecting the re clocked coaxial digital output of the H300 to the external DAC The output of the external DAC will need to be connected to the balanced input of the H300 External DAC With the DAC Loop activated and a digital source input selected the H300 will enable the selec
8. ted digital source input while selecting the balanced source input as the active input This makes the external DAC able to receive the re clocked digital signal convert it and send it back to the H300 through its balanced input The DAC Loop is activated deactivated by holding the DAC button of the RC8 while pressing the IN but on A dot after the last digit of the displayed source input will indicate that DAC Loop is activated When selecting a digital source input with DAC Loop activated the display will read BAL for a short time This indicates that both the selected digital input and the balanced input are active Rin The IR in connection is a remote control input that may be connected to a wired remote control system or an IR repeater This input may be used to control the H300 in the same way that a Hegel remote control would Set Power Up Volume A user defined volume value may be used as the power up volume As a precaution the power up volume value is limited to a maximum level The current volume is set as the power up volume by pressing and holding the DAC button while pressing Vol on the RC8 remote control Reset to factory default settings By pressing and holding the DAC button while pressing Mute on the RC8 the H300 will be reset to fac tory settings This will clear all user defined settings and reinitialize the H300 TRANSPORT AND SHIPMENT If you are packing the amplifier for shipping please follow these instru
9. z Damping factor More than 1000 main power output stage Dimensions 12cm x 43cm x 38cm HxWxD 25kg shipment weight WARNING Hegel products should only be opened or serviced by certified technicians The devices contain electronic components that may cause severe electric shock Work performed on Hegel products by unqualified personnel may cause serious damage or personal injury Opening of the product by non authorized personnel will void the guarantee The products must not be exposed to rain or moisture WARRANTY All Hegel products come with a 2 year warranty against defective materials and workmanship In case you would need any assistance with your Hegel product please find your nearest dealer or distribu tor by looking at the Hegel web site http www hegel com If you experience any problems locating your dealer or distributor please contact info hegel com ADDITIONAL INFORMATION For additional information please visit www hegel com h300_ga htm USE amp PLACEMENT The HEGEL H300 should be placed on a flat hard surface for proper cooling The amplifier performs best after being switched on for about 1 hour for heating up A certain space is required for air circulation above and below the amplifier The amplifier must never be placed on a carpet or similar surface that obstructs air circulation through the unit Nor must it be covered while in use or placed on a narrow shelf or in another confined space The amplifier will
Download Pdf Manuals
Related Search