TM-CAGE OWNERS MANUAL
Contents
1. Lower collar onto top plate Locate locking notches push down slide into place Cables should be routed through this hole SN M N NS NN Us AA G Q NN VE This hole should be directly over the matching hole in the top plate 12 FIT LOCKS Lower lock into holes as shown Turn 90 Locating locking pin over hole on top collar Push locking pin Reverse steps to uninstall projector TM CAGE_manual_en LOCKS 6 x LR44 AG13 batteries are pre installed in each lock 1 When locked it will beep once to confirm it is armed After 15 seconds it becomes active 2 When moved it will emit 3 warning beeps After 5 seconds of continued movement the alarm will sound 3 When the alarm is sounding if movement ceases for 35 seconds the alarm will stop sounding and return to active mode Lock sensitivity cannot be adjusted NOTE The two keys included are not keyed alike they are specific to each lock The two keys are common to all Vision cages SPECIFICATIONS PLATE PACKAGE SIZES Small Accommodates projectors up to 315 x 235mm Medium Accommodates projectors up to 375 x 300mm SIDE PANEL SIZES Sold separately Necessary to make up a complete cage 80mm 100mm 120mm 160mm BOX DIMENSIONS Small Plate Package 286 x 287 x 84mm Medium Plate Package 326 x 222 x 77mm 80mm Side Package 98 x 87 x 66mm 100mm Side Package 118 x 87 x 66mm 120mm Side Package 138 x 87 x 66mm 160mm Side Pac2. installer e Allow 500mm x 500mm clear space around the bracket e Avoid installing in a moist environment or in direct sunshine or near corrosive gas or liquid e Routing of cables through the bracket must comply with local regulations e Side panels should not obstruct the lens connectivity and airflow access A ENSURE POWER CABLE IS NOT TWISTED SQUEEZED OR SHEARED This product is a theft deterrent and does not guarantee the security of your projector Alarm batteries should be tested at time of installation and annually Vision s liability is limited to the terms set out in the warranty All products are designed and imported into the EU by Vision who is wholly owned by Azlan Logistics Ltd Registered in England Nr 04625566 at Lion House 4 Pioneer Business Park Clifton Moor York YO30 4GH WEEE Registration GD0046SY RoHS 2002 95 EC DECLARATION OF ORIGIN All Vision products are made in the People s Republic of China PRC 3 TM CAGE_manual_en CONTENTS 1 x Top Plate SPCC 2 x Access Prevention Collars SPCC 2 x Disk locks with two keys 1 x Lock Hex Key 16 x Foam Blocks EVA S SOLD SEPERATELY 8 x Side Panels SPCC 11111111 4 TM CAGE manual en INSTALLATION NOTE For the most secure result cage should conform as closely as possible to the size of projector 1 START WITH BOTTOM PLATE Set bottom plate on level non scratch surface 2 ADD FOAM BLOCKS Set foa
3. VISION installation innovation TM CAGE OWNERS MANUAL 1 TM CAGE_manual_en Www visionaudiovisual com techmount tm cage 2 TM CAGE_manual_en DECLARATION OF CONFORMITY Where applicable Vision products are certified and comply with all known local regulations to a CB Certification standard Vision commits to ensure all products are fully compliant with all applicable certification standards for sale in the EU and other participating countries The product described in this owner manual is in compliance with RoHS EU directive 2002 95 EC and WEEE EU directive 2002 96 EC standards This product should be returned to the place of purchase at the end of its useful life for recycling WARNINGS During installation take care to adhere to workplace health and safety laws e Attach this product to a rated load bearing structure A NEVER MOUNT CAGE OR BRACKET DIRECTLY TO A FALSE CEILING e Do not cut or drill any parts above head height This should all be done using the correct safety equipment at floor level It can be attached to brick masonry ceilings e Avoid overstretching which might result in the ladder tipping over e SWL safe working load 7kg e Ensure it is installed in an appropriate place for example not obstructing an emergency exit e Ensure it is at least 2000mm above the ground to prevent accidental injury e Check stability after installation e Installation must be done by a specialist audio visual
4. kage 178 x 87 x 66mm 11 TM CAGE_manual_en PACKAGED WEIGHT Small Plate Package 3 8 kg Medium Plate Package 4 8 kg 80mm Side Package 1 0 kg 100mm Side Package 1 1 kg 120mm Side Package 1 2 kg 160mm Side Package 1 4 kg SAFE WORKING LOAD 7kg COLOUR Satin White WARRANTY This product comes with a 2 year return to base warranty effective from the date of purchase This warranty applies only to the original purchaser and is not transferable For the avoidance of doubt this will be taken from the information held by the appointed national distributor at the point of sale The liability of the manufacturer and its appointed service company is limited to the cost of repair and or replacement of the faulty unit under warranty except for death or injury EU85 374 EEC This warranty protects you against the following e Faulty welds resulting in the product not safely performing its task within the recommended SWL safe working load e Poor finishing resulting in the product not being able to be assembled e External corrosion if identified within 24 hours of purchase The inside of the pipe is not powder coated so light corrosion may develop over time This is normal and does not adversely affect the load bearing capability of the product therefore it is not covered in this warranty If you find you do have a problem with this product you should contact the AV reseller you purchased this product from The original purchaser is responsib
5. le for shipment of the product to the manufacturer s appointed service centre for repair We will endeavour to return repaired units within 5 working days however this may not always be possible in which case it will be returned as soon as practically possible This warranty does not protect this product against faults caused by abuse misuse or incorrect installation which might be caused by ignoring the guidelines set out in this manual If failure is not covered by this warranty the owner will be given the option to pay for labour and parts to repair the unit at the service company s standard rate LEGAL DISCLAIMER Because we are committed to improving our products the details above may change without prior warning This User Manual is published without warranty and any improvements or changes to the User Manual necessitated by typographical errors inaccuracies of current information or improvements to programs and or equipment may be made at any time and without notice Such changes will be incorporated into new editions of the User Manual 12 TM CAGE_manual_en
6. m blocks on each corner of plate 3 PUT PROJECTOR ON BLOCKS Projector should be upside down Locate blocks so they do not push projector function buttons 5 TM CAGE_manual_en 4 FIT SIDE PANELS TO LONG SIDES Step 1 Hook the side panel in the notch at the centre NOTE As long as projector cannot be manoeuvred inside cage one side panel can be left off to avoid obstructing projector lens 6 TM CAGE_manual_en 5 FIT TOP PLATE Locate the top plate over the projector and hook to the side panels already in place one side at a time No force should be required 6 SLIDE SIDE PANELS TOWARDS CENTRE Until they stop TM CAGE_manual_en FIT SIDE PANELS TO SHORT SIDES Step 1 Hook the side panel in the notch at the centre 7 Step 2 Hook top of side panel to top plate ON NX Step 3 Slide panel towards corner until it stops N AN IN M Vamy 9 7 Mat Step 4 Repeat until all side panels in place 8 TM CAGE manual en FIT CAGE ASSEMBLY TO PROJECTOR MOUNT Follow the instructions to install the ceiling 8 mount correctly drop cables down the pole then attach cage using pin hex security bolts which come with Vision mounts V JAYY NALI s TW a 72 MU ee sf M PLUG CABLES IN 9 10 TURN ON AND ADJUST Fine Tune pitch and roll of the projector Tighten bolts WH 7 fe 9 TM CAGE manual en 11 FIT COLLARS
Download Pdf Manuals
Related Search