Version 1.0 - partirentournee
Contents
1. Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using the standard DMX controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 ohms resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 11 5 DMX PROTOCOL hannel Channel Value Type of control 16 al bit Pan movementbyss oss 255 Pan movement Penmovementby sar 530 proporonal Pan fine 0 255 Fine control of pan movement NeT ae 0 255 Tilt movement ae 280 eee Tilt fine 0 255 Fine control of tilt movement proportional2. g 000000000 000000000 ix 379 J gt 26 11 Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not build up on or within the fixture Otherwise the fixture s light output will be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life A soft lint free cloth moistened with any good glass cleaning fluid is recommended under no circumstances should alcohol or solvents be used DANGER Disconnect from the mains before starting any maintenance work The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates Replacing the fuse If the lamp burns out the fine wire fuse of the device m
3. 1 Switch On the SERVOSPOT and wait until the fixture reset has finished 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows LAMP Confirm by pressing Enter key 3 Use the Up and Down keys to select On for switch On the lamp and Off for switch Off the lamp and press Enter to confirm or Mode to cancel Note It is also important to note that the discharge lamp is cold restrike types that means that they have to be cold before re striking For this reason you have to wait 5 minutes max speed of fan must be adjusted after having switched Off the lamp before you can switch it back On again If you try to switch On the lamp within 5 minutes after having switched it Off the SERVOSPOT will store this information and automatically ignite the lamp when the 5 minutes period has expired The message HEAt will appear on the control board display at the back side of the SERVOSPOT If the ignition of the lamp is seven times unsuccessful on the display will appear LA Er meaning that the lamp could be damaged or even missed or there could be a failure on the ignitor or ballast 7 3 Colour wheel The SERVOSPOT features a colour wheel with 12 color positions 11 of these with dichroic colors and the last one open The wheel can be positioned between two adjacent colors in any position It is also possible to rotate the color wheel continuously
4. Speed of PAN TILT movement 0 Max speed tracking mode step 1 249 From max speed to min speed vector mode proportional 250 255 Max speed black out while PAN TILT moving or step color changes tracking mode Lamp on off reset fans speed control From max speed of fan to min speed of fan proportional Lamp on reset step No function step Lamp off after 3 sec step No function step Colours Open white proportional Turquoise proportional Red proportional Cyan proportional Green proportional Magenta proportional Light Blue proportional Yellow proportional Green proportional Pink proportional Blue proportional Orange proportional Forwards rainbow effect from fast to slow proportional No rotation proportional Backwards rainbow effect from slow to fast proportional 7 Effect wheel Open position hole 3 facet rotating prism Prism gobo macros Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 Macro 7 Macro 8 12 Channel Channel Value Type of control 16 bit 8bit Macro 9 Macro 10 Macro 11 Macro 12 3 facet prism rotation control 0 No rotation step 1 126 Forwards rotation from fast to slow proportional 127 128 No rotation step 129 255 Backwards rotation from slow to fast proportional Rotating gobos Open step Rot gobo 1 multicolor dichroic step Rot gobo 2 glass step Rot gobo 3 metal step Rot gobo 4 metal step Rot gobo 5 metal step Rot gobo 6 metal step Rot gobo wheel cont r
5. temperature inside increases about certain level the low fan speed reduces the cooling of the lighting This cycle can repeat several times until the temperature inside is on suitable level 3 LOOF low speed Switch Off the lamp operating the fan keeps the adjusted low speed until the temperature exceeds max inside temp Then the SERVOSPOT automatically switch Off the lamp 4 LoHI low high speed of the fan operating the fan keeps the adjusted low speed until the temperature exceeds max inside temp of the fixture then the SERVOSPOT automatically switch from low to high the fan speed 8 Control Board The control board situated on the front panel of the SERVOSPOT offers several features You can simply set the lighting address read the number of lamp or unit hours switch On and Off the lamp run test show make a reset and also use special functions for manual demo and service purposes 8 1 Main functions The main menu is accessed by pressing the Mode key press this one so many times until the display shows message A001 with actually stored address Browse through the menu by the pressing Up and Down keys the display shows step by step these messages A001 rPAn rTilt 16br Lati Poti LAMP dEMo rESE SPEC Press Enter if you wish to select one of them The functions are described in the following sections and the function hierarchy is shown below DMX 512 Address settings The letter A flashes Use t
6. and the Up and Down keys in order to display the following messages Colo EFEC rGob Grot calibration parameters Select one of them and press Enter Now you can calibrate the colour gobo and effect wheel by your controller The DMX calibration protocol is described in the table mentioned below DMX Calibration protocol DMX chanel Function 1 Colour 7 Standard protocol o Ereren stendara protocot 12 s Notnoton o After having calibrated required functions press Enter to confirm or Mode to cancel and return to the menu without reset by the ArES function and use the ArES function in order to write the calibration values to the memory EEPROM and to make a reset in order to check the new adjusted positions of the colour effect and rot gobo wheels and gobo indexing Calibration 0 255 Calibration 0 255 Calibration 0 255 D D O O 3 3 D 3 D lt 3 Calibration 0 255 9 Error and information messages HEAt This message appears if you try to switch on the lamp within 5 minutes after having switched it off the lamp is too hot The message will appear on the display if the lamp doesn t ignite within 28 seconds The fixture will store this information and automatically ignite the lamp when the 5 minutes period has expired Caution The message is disabled if the lamp light sensor function EnSn is switched Off only if the lamp was turned Off and On within 5 minutes the message HE
7. max speed max cooling continuous controlling of the fan speed The fan automatically raises its speed in order to control inside temperature of the lighting if the temperature inside increases about certain level the low fan speed reduces the cooling of the lighting This cycle can repeat several times until the temperature inside is on suitable level low speed Switch Off the lamp operating The fan keeps the adjusted low speed until the temperature exceeds max inside temperature then the SERVOSPOT automatically switch Off the lamp low high speed of the fan operating The fan keeps the adjusted low speed until the temperature exceeds max inside temperature of the fixture then the SERVOSPOT automatically switch from low to high the fan speed 20 Default settings Press Enter to reset all fixture personalities not the adjusting functions to the default values On the display will appear rSt meaning that the fixture makes the reset See the table of personality setting and their default positions Personality Display Default values SHADED On OFF Pan reverse Tilt reverse Movement resolution Lamp On after switch the fixture On Switch On Off the lamp light sensor Display On m u Display intensity cu Display reverse PAN TILT feedback Lamp Off via DMX Low fan speed operating Adjusting the default positions of colour gobo a
8. position by external force e g by stroke Use the Up and Down keys to select On if you wish to anable this function or Off if you wish not to return the mowing head to the required position and press Enter to confirm or Mode to cancel and return to the menu 19 Note If feedback was switched Off the pan tilt position is changed by external force and feedbeck is switched On again the moving head might not to be synchronized with the DMX signal You have to make a reset in order to synchronize the moving head with the DMX signal Lamp Off via DMX This function allows you to switch Off the lamp by DMX Use the Up and Down keys to select On if you want to switch Off the lamp by DMX or Off if you don t want to switch Off the lamp by DMX and press Enter to confirm or Mode to cancel and return to the menu Temperature Temperature readouts of the fixture inside in Celsius Inside temperatures below 70 C are not critical 70 C and more lead to the lamp being switched off Please note that the outside temperature should not exceed 45 C Low fan speed operating By using this function you can choose 4 types of low fan speed operating Browse through this menu by the pressing Up and Down keys the display shows step by step these messages HIGH reG LoOF LoHI Press Enter if you wish to select one of them or Mode to cancel and return to the menu high max speed of fans The cooling fans work on
9. At will appear 22 LAEr The ignition of the lamp is seven times unsuccessful the HEAt message appeared six times before and the display shows LAEr meaning that the lamp could be damaged or even missed the fixture is overheating this can occur if the ambient temperature is 45 C or more or there could be a failure on the ignitor or ballast Please place or replace the lamp check the ambient temperature or contact your dealer if the situation was not caused by the lamp Caution The message is disabled if the lamp light sensor function EnSn is switched Off MbEr This messsage informs you that the main PCB does not communicate correctly with the Control Board CoEr color wheel error The messsage will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The color wheel is not located in the default position after the reset rGEr rotating gobo wheel error The message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The rotating gobo wheel is not located in the default position after the reset iGEr rotating gobo indexing error The message will appear after the reset of the fixture and if the magnetic indexing circuit malfunctions
10. E Yi U bi A r C a gt 0O O Adjust la fosition by turning screws and O lt a Screw A Fee Screw B The SERVOSPOT lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp and focus the light on a flat surface wall As the optimum distance of lamp from lens was adjusted during the installing or changing the lamp by turning the screw A it is necessary to adjust only the second position by turning the screw B in order to center the hot spot the brightest part of the beam If the hot spot seems to be too bright you can lower its intensity by moving the lamp closer to the reflector Do so by turning srew A until the light is evenly distributed If the light on the edge seems to be brighter as in the center the lamp is too close at the reflector In this case you need to move the lamp away from the reflector until the light is evenly distributed and the beam appears bright enough 4 3 Installation of an optional lens The device is delivered with a 15 standard lens If you wish to insert an optional 12 or 18 lens please follow the instructions below Optional 12 lens Remove the fixation ring of the 15 lens with an appropriate tool Remove the lens Install the optional 12 lens and fix it with the fixation ring 15 lens optional 12 lens uyl o UD 7 Ee SS DN in QU NN CU L
11. SERVOSPOT auromoated OMF system USER MANUAL Copyright Version 1 0 SERVOSPOT auromeatled gr system Table of contents 1 Safety instructions 1850150 eesen ce cctces cae ckesndett cc eececed teen eee 2e eee ace acne 4 2 Operating determinations eso wi cca cccace ccc tse de cedncide ce eeweeeebha we etnies 5 3 Description of the device nement ententes meniinentes eee 6 PENNS ANN DER RE RE EEE ER ER 7 EN NS AND Es de a E E EEE 7 4 2 Lamp adjustment en eo cest ion 8 4 3 Insalltionof anepionali ens sushi 8 4 4 Inserting Exchanging gobos acca ie dd nn ne 9 4S RON AE URSS SE ee nie 10 4 6 Connection to NEMANS 4 2e ie din nue imiiinnnLe 11 4 7 DMX 512 connection connection between fixtures cece eeeeeeetteetetttttetteeeeeeeeeeees 11 9 DMX PROTOCOLE tee atasaaanaaes 12 6 Addressing ES ics cee ete 14 7 Remotely controllable functions ss 14 PME an autre eee 14 7 2 Switching On and Off the lamp by Control Board 0 eee eee eeeeeeeeeeeeteeteeaeeaaaeees 14 fo COIOUE UIC Sl aean e E nua id amande 14 TA Rotating gobo WA anna a au Ra ea cence 15 1 55 08 TOI UNE PSN La dentiste 15 TO NG seas a ea anne death a tel 15 7 1 Dimmer Sh tter Strobe Se demonter 15 KO PAM cence te moe matoniue dant on 15 8 CONPODB OF en aessssne states ses eue 15 8 1 Mainf NCtIONS a E do mie 15 8 2 SPEC Special f UNCHONS S
12. SPde Co 2 PriS Proe rbo Grof Foc Seri danl PAn3 tilt SPd3 Co 3 SPd4 Prof rbo Grod FocS SEr9 dint 5Pd5 Coif d nE Lamp On automatically This menu allows you to turn the lamp On after switching the fixture On and switch On Off the lamp light sensor Lamp On after switching the fixture On This function enables to turn the lamp On automatically after switching the fixture On Use the Up and Down keys to select On if you wish to turn the lamp On automatically after switching the fixture On or Off if you wish the lamp Off after switching On the fixture and press Enter to confirm or Mode to cancel and return to the menu Switch On Off the lamp light sensor Use the Up and Down keys to select On if you wish to switch the lamp light sensor On and press Enter to confirm or Mode to cancel and return to the menu The option On is for the standard operation Use the Up and Down keys to select Off if you wish to switch the lamp light sensor Off and press Enter to confirm or Mode to cancel and return to the menu Important The option Off is for emergency operation only if the lamp light sensor is defective and you will wait for a delivery of the spare light sensor If the lamp light sensor was switched Off the error messages LAEr SnEr HEAt will not appear on the display only the message HEAt will appear if the lamp was turned Off and On within 5 minutes and at switching On of the lamp t
13. able speed of fans Self resetable thermo fuse Digital serial input DMX 512 DMX control via every stanndard DMX controller 14 DMX channels 8 bit Pan Tilt movement resolution 16 DMX channels 16 bit Pan Tilt movement resolution Channel 1 Horizontal head movement 8 bit Channel 2 Fine Horizontal head movement 16 bit Channel 3 Vertical head movement 8 bit Channel 4 Fine Vertical head movement 16 bit Channel 5 Pan Tilt speed Channel 6 Fan speed On Off lamp reset Channel 7 Colours Channel 8 No function Channel 9 Prism wheel Channel 10 Prism rotation Channel 11 Rotating gobos Channel 12 Gobo rotation gobo indexing Channel 13 No function Channel 14 Focus Channel 15 Shutter strobe Channel 16 Dimmer 25 Pan Tilt Pan movement range 530 Tilt movement range 280 8 16 bit movement resolution Automatic Pan Tilt position correction Maximum PAN movement 530 in 2 65 s Maximum TILT movement 280 in 1 68 s Remotely controllable speed of Pan Tilt movement for easy programming Rigging Stands directly on the floor Mounts horizontally or vertically with 2 clamps 2 truss orientation Safety chain cord attachment point Temperatures Maximum ambient temperature f 45 C Maximum housing temperature t steady state 80 C Dimensions and weight Length of base including handles 372mm Width of yoke 426 mm Height head horizontal 447 mm Weight net 16 kg Shipping weight 25 kg
14. at different speeds the so called Rainbow effect is created 14 7 4 Rotating gobo wheel The rotating gobo wheel includes 4 metal gobos 1 glass gobo and 1 multicolor dichroic gobo rotating in both directions indexable rotating gobo wheel cont rotation slow to fast The multicolor dichroic gobo containing C M Y colors can be combined with the color wheel especially with cyan magenta and yellow colours in order to obtain several different multicolor beams The gobos have an outside diameter of 27 mm and an image diameter of 23 mm 7 5 3 facet rotating prism 3 facet prism rotating in both directions at different speeds 7 6 Focus Motorized focus enables the beam to be focused anywhere on stage 7 7 Dimmer Shutter Strobe Smooth 0 100 dimming is provided by the combined mechanical dimmer shutter unit This unit may also be used for strobe effect 1 10 flashes per second 7 8 Fan The SERVOSPOT is cooled by two axial fans one each in the projector head and one in the base The speed of the fan and of course the noise can be continuously reduced if very quiet performance is required By the Control Board using the FAnS function you can choose 4 types of low fan speed operating 1 HIGH high max speed of fans The cooling fans work on max speed max cooling 2 rEG continuous controlling of the fan speed the fan automatically raises its speed in order to control inside temperature of the lighting if the
15. be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics see the drawing The fixture s base enables to be mounted in two ways Use the clamps with screws M10 or M8 check the base bottom Install a safety wire that can hold at least 10 times the weight of the fixture Never use the carrying handles for secondary attachment 10 XX XXXKKK KN xX XX X2 XXX of Fat 1s XX LM Secure chain 4 6 Connection to the mains Connect the fixture to the mains with the enclosed power plug The earth has to be connected The occupation of the connection cables is as follows Cable Pin International L Brown Live Blue Neutral Yellow Green Earth 4 7 DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly
16. cracks or deep scratches Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock burns due to ultraviolet radiation lamp explosion crash etc 3 Description of the device 1 Moving Head 2 Yoke 3 Base 4 Carrying handles Rear panel 5 Power switch 6 DMX output 7 DMX input 8 9 Powercord Fuseholder Front panel 10 Mode button 11 Enter button 12 Up button 13 Down button 14 Display 4 Installation 4 1Fitting the lamp DANGER Install the lamps with the device switched off only Unplug from mains before To insert the lamp MSD 230 V 250W or MSD 230 V 200 W open the top cover of the head see the drawings to ident
17. flashing at the display 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows A001 Confirm by pressing Enter key and the letter A will flash 3 Use the Up and Down keys to select the desired address 4 Confirm by pressing Enter or Mode to cancel Controlling After having addressed all SERVOSPOT you may now start operating these via your lighting controller Note After switching on the SERVOSPOT will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will start to flash A001 with actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the SERVOSPOT the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link 7 Remotely controllable functions 7 1 Lamp The SERVOSPOT is run with a MSD 250W 200W lamp A relay inside of the SERVOSPOT allows you to switch On and Off the lamp via itself control board on the front panel or via your controller without affecting the rest of the lighting 7 2 Switching On and Off the lamp by Control Board
18. he Up and down keys to select required address 001 497 and press Enter to confirm or Mode to cancel and return to the main menu Pan reverse This function allows you to invert the pan movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Tilt reverse This function allows you to invert the tilt movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Movement resolution By this function you can adjust the desired movement resolution 8 or 16 bit Use the Up and Down keys to select On if you wish the 16 bit high resolution or Off if you wish only 8 bit resolution and press Enter to confirm or Mode to cancel and return to the main menu Note If you adjust the 16 bit resolution the fixture will occupy 16 DMX channels if you adjust the 8 bit resolution the fixture will be operated by only 14 DMX channels Please check the DMX protocol Lamp On time This option enables you to read the total number of hours that the lamp has been powered On Press Enter or Mode to return to the main menu In order to reset the counter to 0 you have to hold the Up and Down button and press the Enter button Power On time By this option yo
19. he electronics will still try to ignite the lamp until it shines even when the lamp is damaged or absent on this account some electronics parts could be damaged 18 Readout DMX values of each channel received by the fixture Use the Up and Down keys to select desired channel and press Enter to read its value coming to the fixture or Mode to cancel and return to the menu This function allows you to adjust the display settings Display intensity By this function you can adjust from 20 to 100 the intensity of the display Use the Up and Down keys to select the level of the display intensity and press Enter to confirm or Mode to cancel and return to the menu Display reverse With this function you can rotate the display by 180 Use the Up and Down keys to select normal display or display turned by 180 and press Enter to confirm or Mode to cancel and return to the menu ca Lin Display On This function allows you to keep the display On or to turn Off automatically 2 minutes after last pressing any key on the control board Use the Up and Down keys to select On if you wish to keep the display On or Off if you wish to turn Off automatically 2 minutes after last pressing any key on the control board and press Enter to confirm or Mode to cancel and return to the menu PAN TILT feedback This function allows to return the mowing head to the required position after changing the
20. i bi aout 17 9 Error and information messages 23 10 Technical specifications sn nn seen ete nn esse nn 24 11 Maintenance and cleaning 208822 emo eee asai aedicecigncnenetenetane 27 PS INN cg cass ee rie iri 27 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Be careful with your operations With a voltage of 230V 115V you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated o
21. ify which cover is top by loosening the 4 Phillips screws on the front and rear sides of the top cover Then open the small lamp cover by loosening 3 fastening screws see the drawing If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer s notes Do not touch the glass bulb bare hand during the installation Make sure that the lamp is installed tightly into the lampholder system 2 Phillips screws Top cover vr SQ ys C O AA oowoo l TI TH l W c D DDC l y IY 3 fastening screws Adjust the optimal distance 1 1 5 mm from the lens by turning the screw A see the drawings Lamp adjustment below Then close the small lamp cover by tighten 3 fasten ing screws again Reclose the top cover of the head and tighten the 4 Phillips screws Before striking the lamp reset the LAti counter in the main menu of the Control Board by pressing the Up and Down buttons in one time and then con firming with the Enter button Do not operate this fixture with opened housing cover 7 4 2 Lamp adjustment Correct Incorrect Optimum distance 1 1 5mm Keep optimum distance to lens f S N ZI
22. ight fuse too Only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure 1 Unscrew the fuseholder on the rear panel with a fitting screwdriver from the housing anti clockwise 2 Remove the old fuse from the fuseholder 3 Install the new fuse in the fuseholder 4 Replace the fuseholder in the housing and fix it 12 Appendix We believe you will enjoy your SERVOSPOT We assure you will enjoy this product for years if you follow the instructions given in this manual If you have any questions and comments please do not hesitate to contact us Please note errors and omissions for every information given in this manual excepted Every information is subject to change without prior notice Any claim due to missing or wrong information in this manual is herewith excluded 27
23. n the rear panel Always plug in the power plug least Make sure that the power switch is set to OFF position before you connect the device to the mains The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee Do not connect this device to a dimmer pack Do not switch the fixture on and off in short intervals as this would reduce the lamp s life During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Do not touch the device s housing bare hands during its operation housing becomes hot For replacement use lamps and fuses of same type and rating only CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics 2 Operating determinations If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising co
24. nd effect wheels By this function you can calibrate and adjust the colour gobo and effect wheels to their standard right positions Use the Up and Down keys to browse through the adjusting menu the display shows step by step these messages PAn Tilt SPEd Colo EFEC Prot rGOB Grot Foc Stro dimr FOAL by which you can adjust the fixture to the required desired position 0 255 before the function calibration Then when the positioning is finished use the last FCAL function Fixture calibration 0 255 0 255 0 255 0 255 1 Calibration via the control board Press Enter and the Up and Down keys in order to display the following messages Colo EFEC rGob Grot for very smooth function calibration Select one of them press Enter and use the Up and Down keys 21 in order to adjust their right value from 0 to 255 Then press Enter to confirm or Mode to cancel and return to the menu This can be repeated for each calibration parameter if it is required When the calibration is finished it is necessary to use the ArES function in order to write the calibration values to the memory EPROM and to make a reset in order to check the newly adjusted positions of the colour gobo and effect wheels When the reset of the fixture is finished the display will show the FCAL message Press Enter to repeat the calibration or Mode to return to the AdJ menu 2 Calibration via the external controller Press Enter
25. ndensation water might damage your device Leave the device switched off until it has reached room temperature Never run the device without lamp Do not shake the device Avoid brute force when installing or operating the device Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The minimum distance between light output and the illuminated surface must be more than 1 meter Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature t 45 C must never be exceeded Otherwise the lamp is switched off and the fixture is out of operation for 5 minutes CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to
26. otation from slow to fast proportional Rotating gobo index rotating gobo rotation 0 127 Gobo indexing proportional 128 190 Forwards gobo rotation from fast to slow proportional 191 192 No rotation step 193 255 Backwards gobo rotation from slow to fast proportional CRE enrein Focus Continuous adjustment from far to near proportional Shutter Strobe Shutter closed step No function shutter open step Strobe effect from slow to fast max 10 flashes second proportional No function shutter open step Pulse effect in sequences proportional No function shutter open step Random strobe effect from slow to fast proportional No function shutter open step Dimmer intensity Gradual adjustment of the dimmer intensity proportional from 0 to 100 6 Addressing The control board on the front panel of the SERVOSPOT allows you to assign the DMX fixture address which is defined as the first channel from which the SERVOSPOT will respond to the controller If you set for example the address to channel 5 the SERVOSPOT will use the channel 5 to 20 for control Please be sure that you don t have any overlapping channels in order to control each SERVOSPOT correctly and independently from any other fixture on the DMX data link If two three or more SERVOSPOT are addressed similarly they will work similarly For address setting follow this procedure 1 Switch On the SERVOSPOT and wait until the fixture reset has finished rSt is
27. r wheel continuous rotation in both directions rainbow effect Via the combination between multicolor dichroic gobo and color wheel even more color combinations possible 24 Rotating gobos Rotating gobo wheel with 6 interchangeable and indexable rotating gobos plus open Rotating gobo wheel cont rotation 4 metal gobos 1 glass gobo and 1 multicolor dichroic gobo rotating in both directions at different speeds Rotating gobos can be turned by 360 the adjusted position is memorized Gobo indexing 3 additional metal gobos and 2 glass gobos are included Outside diameter 27 mm image diameter 23 mm Strobe Strobe effect with variable speed 1 10 flashes per second Preprogrammed variable random strobe and dimmer pulse effects Dimmer Smooth dimmer from 0 100 Prism 3 facet prism rotating in both directions at different speeds Macro function for rotating gobos rotating prism combinations Focus Remotely controllable motorized focus from near to far Motors 10 high quality stepping motors controlled by microprocessors Electronics Addressing special functions setting effects calibration via control panel with 4 digit LED display Readout fixture and lamp usage receiving DMX values temperature etc Built in analyzer for easy fault finding error messages Remotely switching of the lamp Bilt in demo sequences Black out while head moving or gobo color prism changing Silent fans cooling remotely controll
28. sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The rotating gobo is not located in the default position after the reset PrEr prism error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The prism wheel is not located in the default position after the reset FtEr This error message informs you that the fixture was overheating occured if the ambient temperature is 45 C or more and that the relay switched off the lamp This message will appear on the display until the temperature will be on a suitable level then the display will show the massage HEAt meaning the lamp is too hot explanation see above SnEr This message appears if the lamp lighting sensor is failed Caution The message is disabled if the lamp light sensor function EnSn is switched Off PoEr This message will appear if the fixture was shortly disconnect from the main PAEr Pan yoke movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuits malfunction sensors failed or magnet missing or the stepping motor is defective Or its driving IC on the main PCB The yoke is not located in the default position after the reset tiEr TILT head movement error This message will appear af
29. ter the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective Or its driving IC on the main PCB The head is not located in the default position after the reset FrEr It will appear if the frequency of the main is not standard 50 or 60 Hz 23 10 Technical specifications Power supply EU model Voltage 210 230 250V AC 50 60 Hz aF USE ira ii ere T 3 15A 230V US model Voltage 100 115 20 8 230V AC 50 60 Hz aa einer ere T 6 3A 115V Power consumption 500W Compatible lamps MSD HSD 230 V 250 W GY 9 5 or MSD HSD 230 V 200 W GY 9 5 Optical system High luminous efficiency parabolic mirror and double condenser system Standard 15 focused beam angle Optional 12 and 18 lens Alllenses are anti reflection coated Beampath Standart 15 objective ee 3230 807 360 200 LUX E g 3 to E oO D om o 10 15 20 Distance m o 1 PA 2 36 3 55 4 73 Diameter m Optional narrow TASSE a 4010 1000 250 LUX E 3 D 2 3 2 o gt 4 E 2 D co 20 Distance m a 4 is 4 20 Diameter m Optional wide 18 objective s 2480 620 260 155 LUX D j S O E D a o 5 10 15 20 Distance m o 1 43 2 86 4 29 5 72 Diameter m Colours Color wheel with 11 dichroic filters plus open Colou
30. u TE ps Sn NI RAU il D Wf A N Optional 18 lens Unscrew the knurled head screw on the plate of the light output Install the optional 18 lens and fix it with the knurled head screw ni fin W So O LY 4 4 Inserting Exchanging gobos DANGER Install the gobos with the device switched off only Unplug from mains before To insert the gobos open the top cover of the head by loosening the 4 Phillips screws on the front and rear sides of the top cover If you wish to use other forms and patterns as the standard gobos or if gobos are to be exchanged please follow the instructions below Rotating gobo wheel CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in front of the gobo o DEN KORA VID C7 o 4 5 Rigging the fixture Danger of fire When installing the device make sure there is no highly inflammable material decoration articles etc in between a distance of min 0 5 m Warning Use 2 clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure The SERVOSPOT can
31. u can read the total number of hours that the SERVOSPOT has been powered On Press Enter or Mode to return to the main menu Switch On Off the lamp Use the Up and Down keys to select On if you wish the switch On the lamp or Off if you wish switch Off the lamp and press Enter to confirm or Mode to cancel and return to the main menu 16 Demo sequences This function allows you to run a special demo test sequences without an external controller which will show you some possibilities of using SERVOSPOT Press Up and Down keys to select the Mod1 or Mod2 sequences The Mod1 is suitable for projections on the wall ceiling or ground without any head movement the Mod2 uses all SERVOSPOT functions and therefore is good for a complete introduction of the fixture 0 255 0 255 0 255 run Reset function Press Enter key to run reset This option enables the SERVOSPOT to index all effects functions and return to their standard positions 8 2 SPEC Special functions Use the Up and Down keys to browse through the special functions and select the one by pressing Enter 17 Manual control of effects This function allows you to control manually the channel functions of the fixture Use the Up and Down keys to select desired function and press Enter to adjust the effect or Mode to cancel and return to the menu T y L u PAn ti bilti SPdi Co HOLE Prol rbog Grol Foci GPEn nb PAn tilt
Download Pdf Manuals
Related Search