NOTE - Utax
Contents
1. DOCUMENT CONSULTING INSTRUCTION HANDBOOK LARGE FORMAT SYSTEM Thank you for purchasing the Copier XC 9020 This USER S MANUAL contains functional and operational explanations for the XC 9020 Please read this USER S MANUAL carefully before using the Copier Please keep this USER S MANUAL for future reference 1 When this product is installed in North America This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2 When this product is installed in Europe This equipment complies with the requirements in Pub 22 of CISPR Rules for a Class B computing device Operation of this equipment in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install Machine around other electronic equipment or other precision instruments Other devices may be effected by electrical noise during operation If the Machine is installed near other electronic equipment such as a TV or a radio interference to said equipment such as noise or flickering may occur Use a separate power line and install the COPIER as far as possible from said equipment This product meets the ENERGY STAR guidelines for energy2. CLEAR DECREASE INCREASE CLEAR DECREASE INCREASE 3 8 Chapter 3 Useful Function 4 Open the Original Table 4 Move the Original Guide 5 according to the width of original as needed 5 Put the original with face down on the Original Table and then insert it under the Original Feed Unit along the Original Guide 5 until the leading edge touches the feeding roller Then slide the Original Guide 5 fully to the The Original is transported a little remains a moment and then transported for the scan A NOTE If the Original Guide 5 is not at the far right position the WAIT Indicator lights and it is impossible to start the multiple copy 6 The XC 9020 scans the original as many times as the Copy Number by transporting forward and backward If the Copy Number is 8 for example the original is scanned 8 times successively 3 9 Chapter 3 Useful Function 7 The Original is ejected from the Copy Exit after scanning 8 Copies are ejected from the Copy Exit 3 10 Chapter 3 Useful Function 3 6 Power Saving Mode and Power OFF Mode You can enable the Power Saving Mode or the Power OFF Mode to save the power consumption when the XC 9020 is not used for a long time 3 6 1 Power Saving Mode The Power Saving Mode is the function to reduce the power consume when you do not make any operation for some period although you leave the XC 9020 ON You can work the Power Saving Mode
3. CO TRAIL EDGE JB 7 I O DECREASE INCREASE STOP CLEAR ALL CLEAR 2 If necessary change such settings as Copy Density Leading Trailing Margin and so on Refer to Chapter 3 as for the details of each setting 3 Open both the Original Table 1 and the Bypass Feeder Table 2 2 16 Chapter 2 Basic Operation 4 There are several Size Marks 3 on the Bypass Feeder Table Align the edge of cut sheet paper with the Size Marks 3 and insert the cut sheet into the Bypass until it touches the feeding roller Cut sheet paper is transported in a little and then awaits the original to be inserted A NOTE Normally the Roll Paper Feeding Mode is selected But if only you set the cut sheet paper the Cut Sheet Paper Feeding Mode is automatically selected The CUT SHEET Indicator on the Operation Panel automatically lights instead of ROLL Indicator at this time e GD gt TO s FH SL C COCO CO A 2 00 00 J U LIGHTER DARKER DL FILM CO VELLUMTRACING ca PLAIN PAPER e CHD gt TO naa F SL C I C OCI A I 2 OY J DJ U LIGHTER DARKER CO FILM CO VELLUMTRACING EI PLAIN PAPER 8 8 oO O oO 0 CLEAR DECREASE INCREASE CLEAR DECREASE INCREASE MODE LEAD EDGE L CUT MODE TRAIL EDGE A A zu je BE a t OLA 4 t a ne mB 0 mm LI CLEAR CLEAR ALL CLEAR ALL CLEAR CO TRAIL EDGE 2 17 Chapter 2 Basic Operation 5 Move th
4. DECREASE INCREASE C LEAD EDGE C4 CUT MODE CO TRAIL EDGE Je 7 II t DECREASE INCREASE m STOP CLEAR ALL CLEAR Chapter 3 Useful Function 3 3 Selecting the Cut Mode You can specify the Cut Mode of roll media Synchronous Cut and Standard Cut are selectable Reference The roll paper is cut as long as the copy image if you select the Synchronous Cut Please select the Synchronous Cut when the size of copy image is not standard as D size or E size because of original size magnification and so on The roll paper is cut by the standard size length as AO or A2 if you select the Standard Cut Selectable standard sizes length are A4 A3 A2 A1 AO size and 48 inches regardless of the width of roll paper Please select the Standard Cut if the copy image is standard size Or the printed copy sheet should be standard size even if the copy image is not so 1 Press the Cut Mode Select Key 1 The CUT MODE Indicator 2 lights and it becomes nm a possible to change the setting value indicated on the STAND BY Indication Part 3 ron wwe F 2 Change the setting value Cut Length pressing both a mms 7 en the DECREASE Key and INCREASE Key 4 CJ LI I Selectable setting values are A4 A3 A2 A1 AO 48 encore and SC Ta MEDIA SC means the Synchronous Cut and others are standard sizes en Ji u CI CUT SHEET Ce L J L CLEAR DECREASE INCREASE C4 LEAD EDGE CU
5. CLEAR ALL CLEAR 2 Setthe Original to the XC 9020 The original is transported about 280mm long for the Sample Copy and then it is returned to the front The Sample Copy about 280mm long is ejected from the Copy Exit 3 16 Chapter 3 Useful Function Chapter 4 Error Treatment Page 4 1 Call Operator Err rs Ss 4 2 41 1 RNS eTOCs Zee 4 2 A 1 1 1 Code JO Original WIS COG era 4 4 4 1 1 2 Code 3 Paper Mis feed at Paper Entranee Area at 4 5 4 1 1 3 Code J2 Paper Mis feed at Paper Turning Area ee 4 7 4 1 1 4 Code J3 Paper Mis feed at Print Area or Copy Exit Area v 4 9 4 1 1 5 Code J4 Incorrect insertion of Cut Sheet Paper me 4 13 4 1 1 6 Code J5 Mis feed of cut sheet paper at Paper Turning Area s 4 14 4 1 1 7 Code J6 Mis feed of cut sheet paper Incorrect size a 4 17 A 1 2 Oth rf Err rs H sHtse ee es 4 20 4 1 2 1 Roll Empty 4 20 41 2 2 Toner Empty EEE a EA A EE EEA ee aces cece ae ee eu ne esa eee he 4 20 41 2 3 Waste Toner F ll esse aan 4 21 4 1 2 4 Incorrect set of original or cut sheet paper READY amp WAIT Indicators flash simultaneously ETE EESE rn erent 4 21 4 2 BallServieeiErr rs aana R R R E AE RSN 4 22 4 1 Chapter 4 Error Treatment 4 1 Call Operator Errors 4 1 1 Mis feed Errors 8 If the copying paper or the original is mis fed anywhere in the machine the Mis feed Indicator 1 on the Operation Panel 2 lights to inform you of
6. a copy is completed STAND BY Key Press the STAND BY to enter the Power Saving Mode Refer to 3 6 Power Saving Mode and Power OFF Mode on and after the page 3 11 as for the Power Saving Mode Service Call Indicator lights when the XC 9020 has a Service Call Indicator significant error or problem that a user can not fix by him herself Call your service personnel when it lights Door Open Indicator The Door Open Indicator lights when any of Upper Unit Exit Cover Front Door or Toner Hatch is opened or not locked firmly SL Indicator The SL Indicator lights when you select the SL Strong Light Mode Refer to 3 2 Adjusting the Copy Density on the page 3 3 as for the SL Mode SL Key Press the SL Key to select the SL Mode Refer to 3 2 Adjusting the Copy Density on the page 3 3 as for the SL Mode FILM Indicator The FILM Indicator lights when the roll paper installed to the machine is a film VELLUM TRACING Indicator The VELLUM TRACING Indicator lights when the roll paper installed to the machine is a vellum or tracing paper The PLAIN PAPER Indicator lights when the roll paper installed to the machine is a plain paper The ROLL Indicator lights when the roll paper feeding mode is selected The CUT SHEET Indicator lights when the cut sheet paper feeding mode is selected CLEAR Key Copy number Press the CLEAR Key Copy number to clear the setting value of copy number LEAD EDGE Indicator This
7. the media is removed Do not leave upper unit open If the Drum is damaged you will have to replace it as it is a very important part in creating the print image 4 15 Chapter 4 Error Treatment 4 Close the Corner Transport Unit 3 and lock it moving the Levers 2 outward 5 Close the Upper Unit finally A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed paper If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 16 Chapter4 Error Treatment 4 1 1 7 Code J6 Mis feed of cut sheet paper Incorrect size Mis feed Code J6 is indicated when you set a cut sheet i paper of incorrect size oe Incorrect size means shorter than 279mm or longer than or 3 meters ro INT el Fa SL CJ COC Goo Cod CO Oo Original Exit I L R LIGHTER DARKER Original FILM DI VELLUM TRACING EI PLAIN PAPER MEDIA CoO ROLL Ji C CUT SHEET Ce HJ A CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE CO TRAIL EDGE Dr 9 I oO DECREASE INCREASE Rear q gt Front EI STOP v ALL CLEAR Remove the mis fed original in the following direction 1 Open the Upper Unit 1 4 17 Chapter 4 Error Treatment 2 There are Levers 2 at both sides of the Corner Transport Unit 3 Pull both Levers 2 inward to open the Cor
8. CO VELLUMTRACING EI PLAIN PAPER MEDIA Ca ROLL 7 CI CUT SHEET Ce L J L CLEAR DECREASE INCREASE C LEAD EDGE C4 CUT MODE CO TRAIL EDGE r Je uo o O DECREASE INCREASE fod i STOP CLEAR ALL CLEAR 4 1 2 2 Toner Empty er The Toner Empty Indicator 1 lights if the toner is emptied in the middle of copying e m STAND BY Please add the toner to the machine making reference to a 2 4 Add the Toner on the page 2 9 POW ea SL eee D O I Ca FILM DI VELLUMTRACING DI PLAIN PAPER Tr CI ROLL 7 5 CUT SHEET C YJ Ro CLEAR DECREASE INCREASE C LEAD EDGE C4 CUT MODE CO TRAIL EDGE r e Woo O OD DECREASE INCREASE To i STOP CLEAR ALL CLEAR 4 20 Chapter 4 Error Treatment 4 1 2 3 Waste Toner Full x The Waste Toner Full Indicator 1 lights when the Waste E D a Toner Bottle is filled with the toner Replace the Waste Toner Bottle with the new one making n a amp H FFT reference to 2 7 Replacing the Waste Toner Bottle on the 245 page 2 20 Fe a LIGHTER DARKER STAND BY LI FILM DI VELLUMTRACING EI PLAIN PAPER MEDIA CO ROLL Ji C1 CUT SHEET oe HL I CLEAR DECREASE INCREASE C LEAD EDGE C4 CUT MODE C4 TRAIL EDGE je I oO DECREASE INCREASE cS a STOP CLEAR ALL CLEAR 4 1 2 4 Incorrect set of original or cut sheet paper READY amp WAIT Indicators flash simultaneously Both the RE
9. Operation 3 Ensure that the Original Table 1 is open Move the Original Guide 2 according to the 1 2 width of original as needed NOTE In case you will make a multiple copy slide the Original Guide fully to the right after you insert the original Otherwise it is impossible to start multiple copy 4 Put the original with face down on the Original Table and then insert it under the Original Feed Unit along the Original Guide 2 until the leading edge touches the feeding roller The Original is accepted a little remains a moment and then transported for the copy A NOTE Please wait for a moment if the WAIT Indicator is lighting as it is impossible to make a copy If you set the original although the machine is warming up both the READY indicator and WAIT indicator flash at the same time 2 14 Chapter 2 Basic Operation 5 The Original is ejected from the Original Exit after the scan 6 Copy is ejected from the Copy Exit 2 15 Chapter2 Basic Operation 2 6 Copying with Cut Sheet Media A NOTE It is impossible to make a multiple copy by Cut Sheet Paper Feeding Mode 1 Confirm that the Ready Indicator on the Operation Panel is lighting Ready Indicator O TO snau F SL C COCO CO AA 2 00 002 J O PL LIGHTER DARKER Ca FILM C4 VELLUM TRACING EI PLAIN PAPER MEDIA C4 ROLL Jl Co CUT SHEET Ce LI A CLEAR DECREASE INCREASE C4 LEAD EDGE co CUT MODE
10. T AAAA Replacing the Roll Media Slide ONE EEEE E iii Wie nt Ase A Kae E A Eh aa Rial EE T Replacing the Waste Toner Bottle EEE E i ac cea a a cee chia Chapter 3 Useful Functions 3 1 3 2 3 3 3 4 3 5 biti ali AR Adjusting the Copy Density 000 Selectingthe Cut Mode eter eee Adjusting the Leading Trailing Margin 0 0 00 Multiple Copy IN RN ALATA NER TREE RY RAPA ERR EENAA EMERY AY RY YALA NER AE EYER NER EERE CREAR REE 9 Page 1 2 3 1 4 1 5 1 6 1 8 1 9 1 10 1 10 1 12 1 13 3 6 Power Saving Mode and Power OFF Mode _ een 3 11 3 6 1 Power Saving Mode RN RE FERNER NER CH a HERGETRU RAU RI RL TER RL ENLDE ERCB AL WERNER RICH AERTEUR 3 11 3 6 1 1 Power Saving Mode Manual Bases Sea anes eee tens eae ees ened deme 3 11 3 6 1 2 Power Saving Mode Automatic eT er RUE ere RUE TE RUE EEE TE RUE EEE EEE EEE rE Te ere arte vr ree 3 12 3 6 2 Power OFF Mode aussen sk uaa eeca ead sence aan 3 13 3 7 Dehumidifying the Roll Medi3 88 Heer 3 15 3 8 Sample Copy De ee et tit nl et en ae oes not en ee ease Te 3 16 Chapter 4 Error Treatment 4 1 Call Operator Emors elle eee 4 2 41 1 Meee MCS eee eee 4 2 4 1 1 1 Code JO Original MIS TOCO zer a eee nanan 4 4 4 1 1 2 Code J1 Paper Mis feed at Paper Entrance Area see 4 5 4 1 1 3 Code J2 Paper Mis feed at Paper Turning Area ee 4 7 4 1 1 4 Code J Paper Mis feed at Print Area or Copy Exit Area 4 9 4 1 1 5 Co
11. be transported with skew if the roll paper is loose 2 7 Chapter2 Basic Operation 9 Close the Front Door A NOTE If the Feeding Roller Cover is not closed properly the Front Door can not be closed 10 Cut the leading part of roll paper by the Initial Cut As for the detail of the Initial Cut refer to 3 1 Initial Cut on the page 3 2 2 8 Chapter 2 Basic Operation 2 4 Adding Toner A WARNING There is combustible powder in the toner cartridge Do not burn up the used toner cartridge A NOTE If your hand or your clothing is soiled by toner dust the toner If it is unable to dust it wash the clothing with the cold water Do not use the hot water at this time because the toner will soak into fibres 1 Pull both the Toner Hatch Open Levers 1 inward and open the Toner Hatch 2 2 Slide each green Hook 3 to the arrow mark and remove each Developer Cover 4 2 9 Chapter 2 Basic Operation 3 Prepare 2 Toner Cartridges 5 and shake them left and right several times while facing up its film side 4 One side of each Toner Cartridge has a tape 6 which fixes the film Insert this side of each Toner Cartridge under the holder 7 5 Pulling the green Hook 3 toward the arrow mark press down another side of cartridge The cartridge will be locked firmly if you release the Hook 3 2 10 Chapter2 Basic Operation 6 Strip off the tape 6 which fixes the film 8 and then pu
12. efficiency ENERGY STAR The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations 2002 96 EC of the European Parliament and the council of 27 January The symbol shown indicates that this product conforms to Directive 2003 on waste electrical and electronic equipment WEEE and does not x apply to countries outside of EU Only For EU Member States 1 Safety Warnings The following warnings are very important in order to safely use this product These notes are important in preventing danger to the operator or operation of the machine The following symbols are found throughout the USER S Manual and have the following meaning WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not f
13. in a polyethylene bag Remove the paper from the machine every day in the evening and keep it in a polyethylene bag Then set it to the machine in the next morning Possible trouble Void of image may occur when you make a copy with a plain paper or vellum Treatment 1 Turn on the Dehumidify Heater of XC 9020 to dehumidify the air in the machine 2 Remove the plain paper or vellum from the machine whenever you finish copying and keep it in a polyethylene bag Possible Trouble Void of image or paper crease may occur when you make a copy with a plain paper or vellum Treatment 1 Turn on the Dehumidify Heater of XC 9020 to dehumidify the air in the machine 2 Turn on the air conditioner and the dehumidifier to dehumidify the room air 3 Remove the paper from the machine whenever you finish copying and keep it in a polyethylene bag 1 9 Chapter1 Before Use 1 8 Appearance 1 8 1 Front View Function Original Table Open the Original Table and put the original onto it Copy Exit Bypass Feeder Table F u Upper Unit Open Lever Original Feed Unit Eu Original Feed Table Original Guide Move the Original Guide according to the width of original The original is transported along with it 10 Operation Panel Several copying operations are available Refer to 1 8 3 Operation Panel on the page 1 13 1 10 Chapter 1 Before Use No Function You can turn on off the XC 9020 D 12 Dehumidify
14. of paper are available for copying The maximum width is 914mm 36 inches and the minimum is 216mm The maximum length is 3000mm and the minimum is 279mm Weight Available Copying Sizes Plain Paper 64 to 80g m AO A1 A2 A3 and A4 size 64 to 80g m 120g m If the used paper does not satisfy the above specifications it may cause such troubles as paper mis feed defective image etc Do not use the following kinds of paper because the paper mis feed may occur Torn Folded Made of metal or cloth So much curled In case of the Cut Sheet Paper Metal Punched Rough surface Carbon paper for example Rough surface OHP Film 1 8 Chapter1 Before Use 1 7 Storage of Copying Media According to the humidity of the installation place store the copying media as follows Humidity level Possible trouble and treatment Very low humidity Low Humidity 40 RH to 70 RH High Humidity Very High Humidity Possible trouble Any of void of image or paper crease may occur when you make a copy with a plain paper or vellum Treatment 1 Turn on the air conditioner and the humidifier to humidify the room alr 2 Remove the plain paper or vellum from the machine whenever you finish copying and keep it in a polyethylene bag Possible trouble Void of image may occur when you make a copy with a vellum Treatment Remove the vellum from the machine whenever you finish copying and keep it
15. the error At the same time any Mis feed Code JO J1 J2 J3 J4 J5 or J6 is indicated on the Indication Part 3 to let you Know where the mis feed has occurred e mD gt STAND BY C VELLUMTRACING Ca PLAIN PAPER MEDIA CI ROLL Ji CI CUT SHEET HL A CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE C4 TRAIL EDGE Je OFT 17 DECREASE INCREASE a x STOP CLEAR ALL CLEAR The following figure is the section of the XC 9020 which shows the location of each mis feed More detailed explanation for each code is described on the later pages Original Exit Mas 1 gt Rear em 4 2 Chapter 4 Error Treatment A NOTE 1 Carefully remove the mis fed paper as its edge may be very sharp or you may harm your hand 2 Remove a necklace a bracelet and a wristwatch from yourself before removing the mis fed paper Otherwise you may be burnt or get an electric shock when such metal accessory touches the inside of the printer The toner image is not fixed firmly if the paper did not reach the heater section Therefore be careful not to soil your cloth with the toner when you remove the mis fed paper Please dust the toner if your cloth is soiled If it is unable to dust it wash the cloth with the cold water Do not use the hot water at this time because the toner will soak into fibre The toner image is not fixed firmly if the paper did not reach the heater section The
16. ADY Indicator 1 and the WAIT Indicator 2 flash simultaneously if either original or cut sheet paper is 1 2 incorrectly set to the machine Remove the original cut sheet paper and set it again correctly N a Q GD CHD FR N nn STAND BY I TOI s Eaa y SL C Co C OCI A I O2 OY J LU LIGHTER DARKER Ca FILM CO VELLUM TRACING Ca PLAIN PAPER MEDIA CoO ROLL l C1 CUT SHEET Ce A CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE CO TRAIL EDGE Je I Oo DECREASE INCREASE STOP CLEAR ALL CLEAR 4 21 Chapter 4 Error Treatment 4 2 If the machine has a fatal error the Service Call Indicator 1 Call Service Errors Y lights to inform you of the error Also the Indication Part 2 indicates any of the following Error Code E2 Name of the error Fuser Error High Temperature Fuser Error Low Temperature EEPROM Error Pocket Door Error Switch Abnormal Exposure Lamp Error Dark amp N ai SL P L 9 GD ____ STAND BY C o Oo A CO 2 O2 00 EL a LIGHTER Co FILM C VELLUMTRACING EI PLAIN PAPER CO ROLL Co CUT SHEET Le L CLEAR DECREASE C4 LEAD EDGE CO TRAIL EDGE e Pe DECREASE EB gt STOP ALL CLEAR It is impossible for the user to cure these errors to resolve these issues ga DARKER MEDIA ae I INCREASE co CUT MODE C ge INCREASE LJ CLEAR PLEASE C
17. ALL YOUR TRAINED SERVICE PERSONNEL TO RESOLVE THESE ERRORS If any of the above errors is displayed 1 Turn off the machine wait approximately 30 seconds and then turn on the machine again 2 If the same error code is displayed turn off the machine and then unplug the machine from the wall outlet Call your service personnel 4 22 Chapter 4 Error Treatment Chapter 5 Cleaning and Checking Page 51 Cleaning of Each Part ore nnn 5 2 5 1 1 Original Feeding Part eee ee E E 5 2 5 1 2 Original Cuda seene een 5 2 5 1 Chapter 5 Cleaning and Checking 5 1 Cleaning of Each Part The following parts tend to get dirt so clean them once in a week If they are dirty the copy quality will not be good 5 1 1 Original Feeding Part 1 Open the Original Feed Unit 1 2 Clean the Glass 2 and the Roller 3 with a soft cloth like gauze impregnated with a little water or glass cleaner 5 1 2 Original Guide Clean the Original Table 1 with a wet cloth then with a dry one 5 2 Chapter 5 Cleaning and Checking UTAX GmbH Ohechaussee 235 22848 Norderstedt Germany
18. CING EI PLAIN PAPER MEDIA CI ROLL Ji Co CUT SHEET Ce HL 80 CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE Co TRAIL EDGE zu Bu LI t DECREASE INCREASE FE 5 STOP CLEAR ALL CLEAR 2 Bring up the Feeding Roller Cover 2 N 4 5 Chapter 4 Error Treatment 3 Rewind the roll paper completely Then set the roll paper again NOTE If it is difficult to set the paper again as its leading edge is folded or torn cut it off by the cutter or Scissors 4 Bring down the Feeding Roller Cover 2 and 2 close the Front Door 1 A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed paper If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 6 Chapter 4 Error Treatment 4 1 1 3 Code J2 Paper Mis feed at Paper Turning Area Mis feed Code J2 is indicated when the paper is mis fed at the Paper Turning Area m 2 N 7 eco T Oga a M SL eee Original Exit o g me oao oao oa oa q D ug Original I Lu LIGHTER DARKER LI FILM C VELLUM TRACING DI PLAIN PAPER MEDIA CI ROLL Ji CI CUT SHEET Ce HJ I CLEAR DECREASE INCREASE C4 LEAD EDGE Co CUT MODE CO TRAIL EDGE Je IT DO DECREASE INCREASE Ei u STOP CLEAR ALL CLEAR Remove the mis fed original in the following d
19. Ca PLAIN PAPER MEDIA CoO ROLL Ji CI CUT SHEET Ce HJ A CLEAR DECREASE INCREA DI LEAD EDGE DI CUT MODE DI TRAIL EDGE JP OO I O DECREASE INCREASE Ti STOP CLEAR ALL CLEAR The Indication Part 2 indicates the present setting value of the timer specified to the Power Saving Mode 3 13 Chapter 3 Useful Function 5 Change the setting value of timer by pressing DECREASE Key and INCREASE Key 3 The selectable values are 10 30 1h 1 hour 2h and 4h C4 LEAD EDGE CO CUT MODE C4 LEAD EDGE CO CUT MODE CO TRAIL EDGE M TRAIL EDGE Je Fi aL 7 O I a DECREASE INCREASE We EB STOP STOP ALL CLEAR CLEAR DECREASE INCREASE ALL CLEAR A NOTE It is possible to cancel the setting if you press the STOP ALL CLEAR Key 4 in the middle of setting 6 When you have finished all the settings press the STAND BY Key 1 If you leave the machine without any operation for the time you specified the XC 9020 is turned off automatically by the Power OFF Mode A NOTE If both the Power Saving Mode Automatic and the Power OFF Mode are ON the Power OFF Mode has the priority lt Example 1 gt Power Saving Mode Power OFF Mode 120 minutes The Power Saving Mode works 30minutes later if you make no operation Then the Power OFF Mode works 90 minutes later since the Power Saving Mode has worked lt Example 2 gt Power Saving Mode Powe
20. Dehumidifying THE ROU WGC ctr rn re kt a 3 15 3 8 Sample Copy ELEN EEN LAT EON DMI RST EOE OTE EEE HOE OE OE TOR TOR TOE OE TR OR TNE OR TR OR OE OR TR OR ENEN OR OR OR OR TOR NENN 3 16 3 1 Chapter 3 Useful Function 3 1 Initial Cut In many cases the leading edge of a new roll paper is not straight but is rough folded or torn The Initial Cut is a useful function to straighten it by cutting off the leading part by 280mm long A NOTE The leading part of a roll media will be humidified if it is kept in the machine for a long term without printing which results in a defective image We recommend you to cut it off by the Initial Cut in this case as well 1 Press and hold the LEAD TRAIL Select Key 1 and then press the INCREASE Key 1 in the Leading Trailing Margin setting area A NOTE me m STAND BY Initial Cut Mode is available only while the READY Indicator 3 is lighting TO sn Ea F SL c oono co II 0007 J LI U LIGHTER DARKER Co FILM C VELLUM TRACING DI PLAIN PAPER MEDIA Sore OCU oO DO CLEAR DECREASE INCREASE 2 The roll paper is transported its leading edge is cut off by about 280mm long and it is ejected from the Copy Exit Co LEAD EDGE co CUT MODE I TRAIL EDGE p CI ie t DECREASE INCIREASE B 5 STOP ALL CLEAR 3 2 Chapter 3 Useful Function 3 2 Adjusting the Copy Density The XC 9020 has 14 levels of Copy Density It is possible to select
21. E EEEE AEE EEEE EE 1 8 ST Storage of Copying Media sepsa ERA AE 1 9 8 Appearance E A EEEE A EEEE EE EE A EEE E 1 10 1 8 1 PORE View esse 1 10 1 8 2 REAL VIEW Arte a aa 1 12 1 8 3 Operation Panel 34 hna aaan 1 13 1 1 Chapter 1 Before Use 1 1 Installation Requirements The following conditions are required for installation of the equipment 1 Power source should be rated as follows 220 240V plus 6 or minus 10 50 60Hz 10A 2 The equipment must be on an exclusive circuit 3 The outlet must be near the equipment and easily accessible 1 Make sure to connect this equipment to a grounded outlet 2 For PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible Q The site temperature range 10 to 30 degrees Centigrade with the humidity between 20 to 80 RH NON CONDENSING Keep the machine away from water sources boilers humidifiers or refrigerators 1 The installation site must not have open flames dust or ammonia gases 2 The equipment must not be exposed to the air vents from air conditioners It may affect the image quality 3 The equipment should not be exposed to the direct sunlight Please draw curtains to block any sunlight is within safe levels see certifications Q Ozone will be generated while this equipment is use although the quantity generated Ventilate the room if required Keep ample room around the equipment to ensure comfortable
22. Heater Switch You can turn on off the Dehumidify Heater which dehumidifies the roll paper in the machine Length Counter Total copy length is indicated 1 count 1 meter Upper Unit Open the Upper Unit when you remove a mis fed paper Waste Toner Bottle Waste toner is collected into this bottle 1 11 Chapter1 Before Use 1 8 2 Rear View No Name Function N and open the Toner Hatch Cartridge to supply the toner to the Developer Unit Original Receiver They receive the original after the ejection Toner Hatch Open the Toner Hatch when you supply the Toner 1 12 Chapter1 Before Use 1 8 3 Operation Panel Je STAND BY 20 4 Y j 21 22 SL 6 23 l S 24 8 DI FILM 9 DI VELLUMTRACING WE 95 10 4 PLAIN PAPER ER 11 C7 ROLL Jl 1 12 C CUT SHEET I 26 13 27 DECREASE INCREASE 14 DJ LEAD EDGE DJ CUT MODE 28 15 J TRAIL EDGE An 16 a oo 30 17 31 DECREASE INCREASE 18 32 1 13 Chapter1 Before Use No 3 5 7 N x ant x x lt oO oO BR O NO gt NO WAIT Indicator The WAIT Indicator lights when the XC 9020 is warming up It is impossible to make a copy when it is lighting Also the WAIT Indicator flashes when the Original Guide is not at the far right position It is impossible to make a multiple copy in this case READY Indicator The READY Indicator lights when the XC 9020 is available for copying It is put out when you start copying It lights again when
23. Indicator lights when the Leading Margin Setting is selected TRAIL EDGE Indicator This Indicator lights when the Trailing Margin Setting is selected LEAD TRAIL Select Key Select either the Leading Margin Setting Mode or St Trailing Margin Setting Mode pressing the LEAD TRAIL Select Key Specify the Cut Mode pressing the Cut Mode Select Key 1 14 Chapter1 Before Use No Name Function 18 STOP ALL CLEAR Key 1 Press the STOP ALL CLEAR KEY to stop copying in the middle 2 Also press the STOP ALL CLEAR KEY when the machine is not copying to clear initialize all the settings 19 Mis feed Indicator The Mis feed Indicator lights when the copying paper or original is mis fed anywhere in the machine Roll Empty Indicator The Roll Empty Indicator lights when the roll paper is emptied 21 Wast Toner Full Indicator The Waste Toner Full Indicator lights when the Waste Toner Bottle is filled with the toner or when the Wasted Toner Bottle is installed incorrectly Toner Empty Indicator The Toner Empty Indicator lights when the toner is emptied Copy Density Indicator The selected level of Copy Density is indicated LIGHTER Key Press these keys to adjust the copy density DARKER Key 5 MEDIA Key Make the machine recognize the type of paper pressing the MEDIA Key PLAIN PAPER Indicator VELLUM TRACING Indicator and FILM Indicator lights orderly whenever you press this key Copy Number Indicator The setting value of Copy Num
24. Open Levers 1 at both sides and lift up the Upper Unit 2 2 Loosen the Screw Knob 3 and remove the Bracket of Wast Toner Bottle 2 20 Chapter 2 Basic Operation 3 Remove the Wast Toner Bottle 4 gently 4 Install the new Waste Toner Bottle Then hold it with the Bracket and tighten the Screw Knob 5 5 Close the Upper Unit A NOTE 1 If toner spill out from the bottle clean with a wet cloth 2 If your hand or your cloth is soiled with the toner dust the toner If it is unable to dust it wash the clothing with the cold water Do not use the hot water because the toner will soak into fibre Close the opening of Waste Toner Bottle with an Adhesive Tape and put the bottle into a vinyl bag Keep it until the maintenance service comes 2 21 Chapter 2 Basic Operation Chapter 3 Useful Functions Page 3 1 Initial Cut ses ses u u Scere tr reer tee reer erveerferveer usvert Tree else sere eee mrrtseewrfveve rec leette verses eervrte 3 2 3 2 Adjusting the Copy Density ee 3 3 3 3 Selecting VG CU OC ce 3 5 3 4 Adjusting the Leading Trailing Margin OR OR ONOR OA OR OA OR EN 3 6 3 5 Multiple Copy Sac ee Nc tae nea A u E ease er AAA 5 7 3 6 Power Saving Mode and Power OFF Mode Azureus A E 3 11 3 6 1 Power Saving Mode ram a eermer ste tterserenereneemser ter ter 3 11 3 6 1 1 Power Saving Mode Manual Ele 3 11 3 6 1 2 Power Saving Mode Automatic EINEN 3 12 3 6 2 Power OFF Mode Hs eek 3 13 3 7
25. T MODE I TRAIL EDGE B 0 4 3 5 Chapter 3 Useful Function 3 4 Adjusting the Leading Trailing Margin You can provide the copy with a Leading Trailing Margin A NOTE It is impossible to provide a Trailing Margin when you copy with a cut sheet paper Whenever you press the LEAD TRAIL Select Key 1 the LEAD EDGE Indicator 2 and the TRAIL EDGE Indicator 3 light alternately It is possible to change the setting value of Leading Margin indicated on the Indication Part 4 when the LEAD EDGE Indicator is lighting Similarly it is possible to change that of Trailing Margin when the TRAIL EDGE Indicator is lighting Change the setting value pressing both the INCREASE Key and DECREASE Key 4 The unit of setting is millimetre Setting ranges are as follows Leading Edge 40mm in 5mm increment 2 Trailing Edge 0 to 40mm in 5mm increment 3 3 6 m D emma Cc STAND BY TO sN Eaa F SL al OD je w Eo bay ea J eee LIGHTER DARKER Ca FILM DI VELLUM TRACING EI PLAIN PAPER MEDIA CO ROLL Ji C CUT SHEET gu INCREASE Le HU CLEAR DECREASE LEAD EDGE C4 CUT MODE Chapter 3 Useful Function 3 5 Multiple Copy It is possible to make a multiple copy The maximum Copy Number is 19 A NOTE 1 It is impossible to make a multiple copy by the Cut Sheet Paper Feeding Mode 2 Note that it is unable to make a multiple copy if the original is 1 25m or longer 1 Con
26. ber is indicated 27 DECREASE Key Increase or decrease the setting value of Copy Number INCREASE Key pressing these keys Copy Number CUT MODE Indicator The CUT MODE Indicator shows which Cut Mode is selected presently It lights when the Standard Cut Method is selected and it is put out when the Synchronous Cut Mode is selected Indication Part The Indication part indicates some kinds of information such as the setting value of Leading Trailing Margin Cut Mode and Error Codes 30 Minus indicator The Minus Indicator lights when you input a minus value for the Leading Margin setting DECREASE Key a Increase or decrease the setting value of INCREASE Key Leading Trailing Margin pressing these keys Leading Trailing Margin b Also change the Cut Length pressing these keys in case you select the Standard Cut Mode Clear Key Leading Trailing Press the CLEAR Key Leading Trailing Margin to clear Margin the setting value of Leading Trailing Margin 1 15 Chapter1 Before Use Chapter 2 Basic Operation Page Turning on the XC 9020 40 2 2 Turning off the XC 0000 22 ee nee 2 4 Replacing the Roll Media 2 5 Adding Toner 0 2 9 Copying with Roll Media 9 13 Copying with Cut Sheet Media 2 46 Replacing the Waste Toner Bottle 2 20 2 1 Chapter2 Basic Operation 2 1 Turning on the XC 9020 1 Plug the XC 9020 into an exclusive wall outlet RS A WARNING 1 Do not handle the Power Plug with wet han
27. de J4 Incorrect insertion of Cut Sheet Paper s 4 13 4 1 1 6 Code J5 Mis feed of cut sheet paper at Paper Turning Area s 4 14 4 1 1 7 Code J6 Mis feed of cut sheet paper Incorrect size s 4 17 A 1 2 Other rrr xeric Bee tee et hee choo eee a 4 20 4 1 2 1 Roll Empty qenie 4 20 41 2 2 Toner Empty ee Re RR 4 20 A 1 2 3 Waste Toner Full ee ee et ee 4 21 4 1 2 4 Incorrect set of original or cut sheet paper READY amp WAIT Indicators flash simultaneously 4 21 4 2 Call Service Errors es cn erence non amannan anne 4 22 Chapter 5 Cleaning and Checking 5 1 Cleaning of Each Part ANNETTE EEE E E E eer eteatatetirercter sannian ntnniae eevee E sear erey rer tee iris tier rere mens A erty A AE 5 2 5 1 1 Original Feeding Pa ae eer cect eed ee 5 2 5 1 2 Original G de ee EO 5 2 6 Chapter 1 Before Use Page of Installation Requirements sEateeaecscesees ce eetsee cheeses oud coed oss asta sseesteesteathestns saute ena steesteastea tees cess cheats ck chceSh ce ecathancag oh auesenahentees teas shen ERERIEEEN 122 2 Originals Prohibited from Duplication eR ee HERREN 1 3 3 FESTOS ats aan u 1 4 4 Specifications INBNONRERERENLOEONTENNTERRRSTRRRUNEESEHERRREORHNNEENERANEERERHENSTENTEHERETENNEEHRHERENENNUNNEAUHENNARENMN 1 5 5 Specifications of Original EEE NTBRTER SER TERLCESLTELTENTERSERL BER VEISERLERTERIER PERLDERPEILTESSPEISIERTERSERTERSPERPEELTESSTERSENTERTER TER OES ere 1 6 6 Specifications of Copying Paper AE
28. ds or you may receive an electrical shock 2 Ground the printer for safety 3 Do not plug the printer into a multi wiring connector in which other devices are plugged It may overheat the outlet and may result in a fire 4 outlet must satisfy 220 240V 6 10 50 60Hz and 10A 2 There is a Power Switch 1 on the right front side of XC 9020 Press its side to turn on the XC 9020 2 2 Chapter 2 Basic Operation 3 There is an Operation Panel 2 on the right top of the machine The WAIT Indicator 3 on the Operation Panel lights when the machine is warming up 2 3 O CD TO s aa F SL CI CI C A A CO C C J LIGHTER DARKER C FILM C VELLUM TRACING Ca PLAIN PAPER MEDIA ROLL Ji CJ CUT SHEET Ce HJ I CLEAR DECREASE INCREASE CJ LEAD EDGE DJ CUT MODE CO TRAIL EDGE Je I t DECREASE INCREASE 3 STOP CLEAR ALL CLEAR 4 The Ready Indicator 4 lights when the XC 9020 is ready 4 e L STAND BY TO s Ea F SL CI CI o CoD A 2 02 0100 LJ PL LIGHTER DARKER CO FILM C VELLUMTRACING EI PLAIN PAPER MEDIA CO ROLL Ji Co CUT SHEET HL A CLEAR DECREASE INCREASE C4 LEAD EDGE co CUT MODE CO TRAIL EDGE Je wu DECREASE INCREASE Cg STOP CLEAR ALL CLEAR 2 3 Chapter2 Basic Operation 2 2 Turning off the XC 9020 1 There is a Power Switch 1 on the right front side of XC 9020 Press its O side
29. e Original Guide 4 according to the width of original 6 Put the original with face down on the Original Table and then insert it under the Original Feed Unit along the Original Guide 4 until the leading edge touches the feeding roller The Original is transported a little remains for a moment and then transported for the scan A NOTE Please wait for a moment if the WAIT Indicator is lighting as it is impossible to make a copy If you set the original although the machine is warming up both the READY indicator and WAIT indicator flash at the same time 2 18 Chapter 2 Basic Operation 7 The Original is ejected from the Original Exit after the scan 8 Copy is ejected from the Copy Exit 2 A NOTE 1 The paper feeding mode automatically changes from Cut Sheet Paper Feeding Mode to Roll Paper Feeding Mode after the copy It is impossible to set multiple sheets in to the Bypass Feeder Please set it one at a time When the previous cut sheet paper has been transported the READY Indicator lights and it becomes possible to set the next sheet Note that you can not set the sheet when the READY Indicator is out 2 19 Chapter 2 Basic Operation 2 7 Replacing the Waste Toner Bottle WARNING There is combustible powder in the wasted toner bottle Do not burn up the used wasted toner bottle A NOTE Do not reuse the wasted toner 1 Press down the Upper Unit
30. econds 1 The Indication Part 2 indicates LP at first If you press the DECREASE Key or the INCREASE Key 3 the Indication Part 2 indicates LP and OF alternately LP means the Power Saving Mode OF means the Power OFF Mode As you will specify the timer for the Power Saving Mode from now indicate LP Press the STAND BY Key 1 The Indication Part 2 indicates the present setting GD ____ o STAND BY TO N Eaa F SL C LI o DO AA I 2 OY J ee LIGHTER DARKER LI FILM DI VELLUM TRACING Ca PLAIN PAPER MEDIA COI ROLL Ji CI CUT SHEET of the timer of the Power Saving Mode I A CLEAR DECREASE INCREASE C LEAD EDGE Zo CUT MODE I TRAIL EDGE Je LP mar JE STOP CLEAR ALL CLEAR 4 Change the setting of timer pressing DECREASE Key and INCREASE Key 3 The selectable values are 10 30 1h 1 hour 2h and 4h C4 LEAD EDGE CI CUT MODE CO TRAIL EDGE Ge oF Ju DECREASE INCREASE C4 LEAD EDGE CO TRAIL EDGE B or DECREASE INCREASE fea E Eu STOP CLEAR ALL CLEAR CoO CUT MODE A NOTE It is possible to cancel the setting if you press the STOP ALL CLEAR Key 4 in the middle of setting 5 When you have finished all the settings press the STAND BY Key 1 If you leave the machine without any operation for the time you specified the Power Saving Mode works automatically To cancel the Power Saving Mode press eit
31. et immediately Do not throw toner including wasted toner toner cartridge and used wasted toner bottle into a fire or other sources of heat as it can explode When you discard toner including wasted toner toner cartridge and used wasted toner bottle follow your service personnel s instructions 3 CAUTION Do not install the machine in a humidified room or a dusty room Also do not install the machine on an unstable floor as injuries may occur 1 Unplug the machine before you move it The power cord may be damaged and it may result in a fire or electric shock If you do not use the machine for a long duration holidays company shutdown turn off and unplug the printer from the outlet for safety Do not pull the cord when you unplug the machine as you may damage the Power Cord There are hot items inside of the machine Take great care not to touch these items when you remove mis fed media Ventilate the room well if you print in a small area 4 TABLE OF CONTENTS Chapter 1 Before Use 1 7 1 8 Installation Requirements e em Originals Prohibited from Duplication see Fe tufes erregt a ee er erence Spe NCI ONS see een Specifications of Original Specifications of Copying Paper eenen Storage of Copying Media nininini Appearance wis u a a R FROME WIGWE rise ee 1 8 1 1 8 2 Ra ar View nn 1 8 3 Operation Panel essen IL ETIT ICUIUIUUU Chapter 2 Basic Operation ee NENNEN nn I
32. firm that the Ready Indicator on the Operation Panel is lighting Ready Indicator O Cm ee TO NW aa F SL C COCO DO Al I 2 OY J LU LIGHTER DARKER Co FILM DI VELLUMTRACING EI PLAIN PAPER MEDIA CO ROLL Ji Co CUT SHEET Ce 0 CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE CO TRAIL EDGE Je to DECREASE INCREASE EI i STOP CLEAR ALL CLEAR 2 If necessary change such settings as Copy Density Leading Trailing Margin and so on Refer to Chapter 3 as for the details of each setting 3 7 Chapter 3 Useful Function 3 Specify Copy Number pressing both the INCREASE Key bh D ea and the DECREASE Key 1 The Copy Number Indicator 2 indicates the Copy roO3U NA ST H FF Number you specified t STAND BY SL If you wish to cancel the multiple copy after specifying j f the Copy Number press the STOP ALL CLEAR Key 3 a LIGHTER DARKER The multiple copy is cancelled and the Copy Number un NERO becomes 1 PLAIN PAPER MEDIA ROLL 1 a p en J3 C CUT SHEET C LEAD EDGE DJ CUT MODE II t A NOTE As the Copy Number Indicator has only one digit 10 or larger number is shown by flashing the indication Supposing 3 is indicated on the Copy Number Indicator the Copy Number is 3 sheets if 3 is lighting and it is 13 sheets if it is flashing 3 sheets 13 sheets 3 is flashing CJ ROLL Jl CJ ROLL l CJ CUT SHEET CJ CUT SHEET E IL 80 IL
33. her STAND BY Key or STOP ALL CLEAR Key 3 12 Chapter 3 Useful Function 3 6 2 Power OFF Mode The Power OFF Mode is the function to turn off the XC 9020 automatically if you do not make any copies in the time you specified in advance Reference The purpose of Power OFF Mode is not to consume any power by turning off the machine automatically It can save more power than the Power Saving Mode If you will make copies after the machine has been turned off by the Power OFF Mode it is necessary to turn on the machine again Press the STAND BY Key 1 for 3 seconds The Indication Part 2 indicates LP at first If you press the DECREASE Key or the INCREASE Key 3 the Indication Part 2 indicates LP and OF alternately LP means the Power Saving Mode OF means the Power OFF Mode As you will specify the timer for the Power OFF Mode indicate OF Press the STAND BY Key 1 The Indication Part 2 indicates either on or off which is the present setting of the Power OFF Mode on Power OFF Mode works off Power OFF Mode does not work Select on pressing the DECREASE Key or the INCREASE if you will make the Power OFF Mode work A NOTE If you select off the setting is completed Press the STAND BY Key 1 Ez D a STAND BY TO s aa FH SL C COCO CO A 2 00 002 J U LIGHTER DARKER Ca FILM C7 VELLUMTRACING
34. irection 1 Open the Front Door 1 1 N 2 Bring up the Feeding Roller Cover 2 4 7 Chapter 4 Error Treatment 3 Rewind the roll paper completely Then set the roll paper again NOTE If it is difficult to set the paper again as its leading edge is folded or torn cut it off by the cutter or Scissors 4 Bring down the Feeding Roller Cover 2 and 2 close the Front Door 1 A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed paper If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 8 Chapter4 Error Treatment 4 1 1 4 Code J3 Paper Mis feed at Print Area or Copy Exit Area Mis feed Code J3 is indicated in either of the following i cases Mn CHD gt STAND BY 1 The paper is mis fed at the Print Area Power A Print Area is between Drum and Fuser in the following s Re drawing I Te 2 The paper is mis fed around the Copy Exit FILM a zz C VELLUM TRACING Original Exit DI PLAIN PAPER Tr Original Sr I CI CUT SHEET Ce LI A CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE CO TRAIL EDGE Dr 9 II 0 DECREASE INCREASE STOP CLEAR ALL CLEAR Rear lt q Remove the mis fed original in the following direction 1 Open the Exit Cover 1 and check if you ca
35. ly originals such as government issued passport public or private issued licenses automobile inspection certification IDs and tickets like pass or meal Prohibited items to copy Regulations to control fake currency and Currency Bill Money Bank Note etc Bond Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc Control Law against Forged amp faked Foreign Currency or Foreign Negotiable Foreign Currency Bill Bank Note and Bond Instruments Forged postal stamps control law Unused postal stamps or government postcards Forged revenue stamps control law Government issued revenue stamps and certificate stamps prescribed by Liquor Tax Act or Commodity Tax Act Currency similarity securities Control Law Private issued securities stock draft check goods ticket etc commutation or book tickets Originals protected by the copyright It is prohibited to copy such originals as books music paintings printed copy maps drawings movie and pictures which are protected by the copyright except for personnel family use or similar purpose 1 3 Chapter1 Before Use 1 3 Features 1 2 methods to feed media XC 9020 can feed media by automatic roll paper feeding 1 roll and manual cut sheet feed 2 Cut Modes selection 2 Cut Modes are selectable Standard Cut and Synchro Cut 3 2 copies min for AO size XC 9020 can make 2 AO copies minute 4 Multiple Copy It is possible t
36. manually or automatically 3 6 1 1 Power Saving Mode Manual 1 Reference The purpose of Power Saving Mode is to reduce the power consumption by reducing the temperature of the fuser If you do not make any copy for the time you specified in advance the machine automatically goes into the Power Saving Mode so not to consume the power Or it is possible for you to make the machine go into the Power Saving Mode manually at any time you wish The Power Saving Mode will be cancelled if you press either STAND BY Key or STOP ALL CLEAR Key However please understand it may take time to recover from the Power Saving Mode because it is necessary to heat up the fuser again Copy is not available until XC 9020 becomes ready Press the STAND BY Key 1 D eme cM The Power Saving Mode works so all the indications on STAND BY the Operation Panel are out TO gs a g F ewe 4 SL ee gt E To cancel the Power Saving Mode press either e STAND BY Key or STOP ALL CLEAR Key a gt LIGHTER DARKER LI FILM C VELLUM TRACING Ca PLAIN PAPER MEDIA Soe COT rt oO CLEAR DECREASE INCREASE C4 LEAD EDGE DJ CUT MODE I TRAIL EDGE je I oO DECREASE INCREASE Eg S u STOP CLEAR ALL CLEAR 3 11 Chapter 3 Useful Function 3 6 1 2 Power Saving Mode Automatic The Power Saving Mode automatically works if you do not make any copy for you specified in advance 1 Press the STAND BY Key 1 for 3 s
37. mental condition Temperature for usage 10 to 30 degrees Centigrade Humidity 20 to 80 RH Storage of consumables Wrap the media surely to shut out the humidity Toner bottle Store the toner within the temperature range from O0 to 35 degrees Centigrade and within the humidity range from 10 to 85 RH NOTE The above specifications may change without notice 1 5 Chapter1 Before Use 1 5 Specifications of Original The used original must satisfy the following specifications PL Minimum Maximum Remarks Thickness In case of Single Copy In case of Multiple Copy Width 210mm 841mm S Length 3 000mm fo Also do not use the following kinds of original because you may damage the original or machine Sticked with paste Torn E Folded So much curled Irregular shape Not square Wet Ink is not dried Made of metal or cloth Patched Metal Cloth 1 6 Chapter 1 Before Use Clipped or stapled Rough surface Carbon paper for example Clipped Stapled 0 7 Rough surface 100Punched 1 7 Chapter 1 Before Use 1 6 Specifications of Copying Paper The following sizes
38. n find the mis fed paper Go to the following step 2 if you can find it Jump to the step 4 on the next page if you can not find it 4 9 Chapter 4 Error Treatment 2 Hold the mis fed paper by both hands and pull it out carefully without breaking A NOTE 1 Be careful not to touch on the Fuser Roller and the surrounding parts as they are very hot You will be burnt if you touch such parts 2 Be careful not to touch the Stripper Fingers as they are very sharp Otherwise you may be hurt 3 Close the Exit Cover A NOTE It is recommended to make Initial Cut after removing the mis fed paper as the cut paper will remove the toner dirt on the Heat Roller or some other parts The copy may have some dirty image if you do not make it Refer to 3 1 Initial Cut on the page 3 2 for the way of Initial Cut 4 Open the Upper Unit 2 4 10 Chapter 4 Error Treatment 5 There are Levers 3 at both sides of the Corner Transport Unit 4 3 3 Pull both Levers 3 inward to open the Corner Transport Unit 4 backward 6 Remove the mis fed paper gently A NOTE There is a Photoconductive Drum large cylinder on the bottom of the Upper Unit Do not touch the drum when you remove the mis fed paper or when you open close the Corner Transport Unit Do not leave the Upper Unit open for a long period as the Photoconductive Drum is very sensitive to light Direct sunlight is very harmful That
39. ner Transport Unit 3 backward 3 Remove the mis fed paper gently NOTE There is a Photoconductive Drum large cylinder on the bottom of the Upper Unit Do not touch the drum when you remove the mis fed paper or when you open close the Corner Transport Unit Do not leave the Upper Unit open for a long period as the Photoconductive Drum is very sensitive to light Direct sunlight is very harmful That stated remove the mis feed media and then close the Upper Unit immediately after the media is removed Do not leave upper unit open If the Drum is damaged you will have to replace it as it is a very important part in creating the print image 4 18 Chapter4 Error Treatment 4 Close the Corner Transport Unit 3 and lock it moving the Levers 2 outward 5 Close the Upper Unit finally A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed paper If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 19 Chapter4 Error Treatment 4 1 2 Other Errors 4 1 2 1 RollEmpty y7 The Roll Empty Indicator 1 lights if the roll paper is emptied in the middle of copying db Please replace the roll paper making reference to 2 3 Replacing the Roll Paper on the page 2 5 IO WwW of H FF RI rue SL C Co OO A CO 2 O2 00 DJ DJ LIGHTER DARKER CO FILM
40. o make a multiple copy up to 19 copies We are unable to guarantee the accuracy of the Original feed past 10 sheets during Multiple Copy 5 Sample Copy is available XC 9020 has a Sample Copy function that allows to check the copy image in advance 6 14 kinds of Copy Density Level including SL Mode are available 7 Adjustment of Leading Margin and Trailing Margin 40mm max 8 Easy Operation a Several kinds of operation such as original insertion copy ejection and paper supply can be made in front of the machine b Toner is supplied by Toner Cartridge 9 Environmentally Friendly Design a Power Saving Mode Satisfies the International ENERGY STAR Office Equipment Program b Succeeds a considerable reduction of hazardous substances on its components 1 4 Chapter1 Before Use 1 4 Specifications Subject 60mm per second 1 5 copies AQ minute Maximum Minimum Maximum Minimum Maximum Minimum Copying length Maximum Minimum Warm up time Less than 8 minutes At 23 C 60 RH the rated voltage and plain paper is used First copy time Media feeding method Fusing method Exposure method Development method Dry Mono component Copy magnification ratio Input power consumption Acoustic noise Stand by Printing Impulse sound EN ISO7779 Ozone Max 0 1ppm Measurement method under UL Standard Dimensions 1293mm Width x 460mm Depth x 580mm Height Weight Media 64 to 80g m 64 to 80g m Environ
41. ollow the said instruction When marked with this symbol DO NOT ATTEMPT When marked with this symbol pay close attention to 2 WARNING Ground the product with a correct ground source or you may be electrically shocked The Power source should be as follows 220 240V plus 6 or minus 10 50 60Hz 10A Use a circuit with a dedicated breaker Install the product as close to the wall outlet as possible If you wish to move the machine please contact your service personnel Do not remove the screw and do not open the cover if not instructed to do so in this User s Manual If you ignore this warning you may be burnt or receive an electric shock due to a hot item or electrically charged part inside of the printer Do not disassemble or tamper with the copier It may result in a fire or an electrical shock Do not plug in the machine into a multi wire connector in which some other equipment is plugged into It may cause a fire due to outlet overheating Do not damage the Power Cord by stepping on or placing heavy items on it If the Power Cord is damaged it may cause a fire or you may receive an electric shock REPLACE THE CORD IF DAMAGED Do not put a flower vase a flowerpot or any water filled item on the product Spilt water could cause a fire or an electric shock If the product generates an abnormal smell or noise turn it off and unplug it from the wall electrical outl
42. operation Refer to the following figure The equipment must be levelled and the floor strength must be ample to sustain the weight of the equipment Y 60cm or wider Rear side XC 9020 60cm or 120cm or wider wider Front side 90cm or wider 1 2 Chapter 1 Before Use 1 2 Originals Prohibited from Duplication It may not be allowed to copy every type of original You may be punished by the law if you possess the copy of some types of originals We recommend you to consider the following before you copy originals Originals prohibited from copying by the law 1 It is not allowed to copy Currency Bill Money Bank Note etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments 3 It is not allowed to copy unused postal stamps or government postcards without permission to make replica from Government 4 It is not allowed to copy Government issued revenue stamps certificate stamps which are prescribed by Liquor Tax Act or the Commodity Tax Act Special items 1 It is warned by the government to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you do not copy free
43. per If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 13 Chapter 4 Error Treatment 4 1 1 6 Code J5 Mis feed of cut sheet paper at Paper Turning Area Mis feed Code J5 is indicated when the cut sheet paper is mis fed at the Paper Turning Area m m STAND BY vA 4 or Original Exit rw N oT e re SL Cc CI CO GS OO oO Oooo LI PL LISHTER DARKER Ca FILM DJ VELLUWTRACING EI PLAIN PAPER MEDIA coo DI Io oO CLEAR DECREASE INCREASE 4 LEAD EDGE DD CUT MODE Sheet Paper 3 TRAIL EDGE Rear lt q eee Front Mn oF t DECREASE INCREASE BE i STOP CLEAR ALL CLEAR Remove the mis fed original in the following direction 1 Open the Upper Unit 1 4 14 Chapter 4 Error Treatment 2 There are Levers 2 at both sides of the Corner Transport Unit 3 Pull both Levers 2 inward to open the Corner Transport Unit 3 backward 3 Remove the mis fed paper gently NOTE There is a Photoconductive Drum large cylinder on the bottom of the Upper Unit Do not touch the drum when you remove the mis fed paper or when you open close the Corner Transport Unit Do not leave the Upper Unit open for a long period as the Photoconductive Drum is very sensitive to light Direct sunlight is very harmful That stated remove the mis feed media and then close the Upper Unit immediately after
44. r OFF Mode The Power OFF Mode works 60minutes later if you make no operation but the Power Saving Mode does not work lt Example 3 gt Power Saving Mode Power OFF Mode The Power OFF Mode works 30minutes later if you make no operation but the Power Saving Mode does not work 3 14 Chapter 3 Useful Function 3 7 Dehumidifying the Roll Media If the roll media has too much moisture the toner may not be fixed correctly to the media And also void of image double feeding creasing might occur If the room has humidity turn on the Dehumidify Heater to dehumidify the interior of the machine Open the Front Door 1 and the Dehumidify Heater Switch 2 appears Press H side of the switch to turn on the Dehumidify Heater 3 15 Chapter 3 Useful Function 3 8 Sample Copy Sample Copy is a function to copy only the leading part about 280mm of original for the purpose to check the copy image in advance You can check the result of copy without consuming a great deal of toner or media if needed 1 Press the DECREASE Key 1 when the Copy Number Indicator 2 is indicating 1 The Copy Number Indicator 2 indicates P O m gt STAND BY TOO s aa F SL CI CI o A A I 0 OY 3 O LIGHTER DARKER LI FILM CO VELLUM TRACING ca PLAIN PAPER C7 ROLL CJ CUT SHEET C1 LEAD EDGE C7 CUT MODE C TRAIL EDGE je I O DECREASE INCREASE ed STOP
45. refore be careful that the toner should not get into your eye or be careful not to inhale the toner Please wash out with water if it gets into your eye or mouth 4 3 Chapter4 Error Treatment 4 1 1 1 Code J0 Original Mis feed Mis feed Code JO is indicated when the original is mis fed under the Original Feed Unit on a gt STAND BY Le 4 N Fl Original Exit Y A a COCO GOO 2 Oo 002 3 JO onan oI gt LISHTER DARKER LI FILM CO VELLUM TRACING EI PLAIN PAPER MEDIA CO ROLL l C1 CUT SHEET Ce LI A CLEAR DECREASE INCREASE Co LEAD EDGE co CUT MODE Cd TRAIL EDGE De to DECREASE INCREASE f j STOP CLEAR ALL CLEAR Rear Remove the mis fed original in the following direction 1 Open the Original Feed Unit 1 and remove the original 2 Close the Original Feed Unit 1 A NOTE JO is also indicated if you cancel copying in the middle pressing the STOP ALL CLEAR Key Please remove the original in the above shown direction in this case 4 4 Chapter 4 Error Treatment 4 1 1 2 Code J1 Paper Mis feed at Paper Entrance Area Mis feed Code J1 is indicated when the paper is mis fed at the Paper Entrance Area Original Exit Rear Remove the mis fed original in the following direction 1 Open the Front Door 1 e D Cc SL C IE C C oO CA J LI U LIGHTER DARKER CI FILM C VELLUM TRA
46. stated remove the mis feed media and then close the Upper Unit immediately after the media is removed Do not leave upper unit open If the Drum is damaged you will have to replace it as it is a very important part in creating the print image 4 11 Chapter 4 Error Treatment 7 Close the Corner Transport Unit 4 and lock it moving the Levers 3 outward 8 Close the Upper Unit finally A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed paper If the Mis feed Indicator lights again some more paper may be mis fed anywhere in the machine so please check other areas as well 4 12 Chapter4 Error Treatment 4 1 1 5 Code J4 Incorrect insertion of Cut Sheet Paper Mis feed Code J4 is indicated when you insert the cut sheet paper to the Bypass Feeder mistakenly when the XC 9020 is m copying with the roll paper ic i T Owa wl F i eee Original Exit O oO w o oa a gt lt Original D SL L LIGHTER DARKER Co FILM C VELLUM TRACING Ca PLAIN PAPER MEDIA C7 ROLL Ji Co CUT SHEET Ce A CLEAR DECREASE INCREASE C4 LEAD EDGE C4 CUT MODE C4 TRAIL EDGE Je II 0 DECREASE INCREASE EHE STOP CLEAR ALL CLEAR Rear Pull out the cut sheet paper from the Bypass Feeder A NOTE Confirm that the Mis feed Indicator is put out and the Paper Mis feed Code disappears after removing the mis fed pa
47. t the Holder 9 on the right end of the Toner Cartridge as the following picture A NOTE Do not discard the tape 6 at this point of time because it will be used later 7 Insert the Spool 10 to the holes of Holder 9 while catching the film 8 between its pins Then rotate the Spool 10 clockwise to wind up the film 8 Fix the film roll 8 with the tape 6 Rotate the Spool 10 a few revolutions counter clockwise pull it out from the film roll and then discard the film roll 2 11 Chapter2 Basic Operation 9 Pull each green Hook 3 toward the arrow mark and remove each Toner Cartridge 5 Discard the Toner Cartridge in a proper way 11 Put back the Developer Covers 4 12 Close the Toner Hatch 2 2 12 Chapter2 Basic Operation 2 5 Copying with Roll Media 1 Confirm that the Ready Indicator on the Operation Panel is lit Ready Indicator me a roy s au F SL C o o DO Al I 2 OY I LU LIGHTER DARKER LI FILM DI VELLUM TRACING EI PLAIN PAPER MEDIA CO ROLL Ji Co CUT SHEET e HJ I CLEAR DECREASE INCREASE C LEAD EDGE DI CUT MODE C4 TRAIL EDGE je I t DECREASE INCREASE E u STOP CLEAR ALL CLEAR 2 If necessary change such settings as Copy Density Leading Trailing Margin and so on Refer to the pages in Chapter 3 as for the details of each setting 2 13 Chapter2 Basic
48. to turn off the XC 9020 2 4 Chapter2 Basic Operation 2 3 Replacing the Roll Media 1 Open the Front Door 1 and then pull out both the Spool Guides 2 2 Lift up the core of roll paper with the Spool holding its both sides 3 Press down the Lock Lever 3 to unlock the core of roll paper and then pull out the Spool 4 from the core 2 5 Chapter 2 Basic Operation 4 Insert the Spool into the new roll paper with pressing down the Lock Lever 3 And then align the side face of roll paper with the concerning size mark 5 printed on the Spool When aligned release your hand from the Lock Lever 3 to lock the roll paper firmly 5 Install the Spool with the new roll paper to the inner groove of the Spool Guides Then push in the Spool Guides NOTE 1 Return Spool Guide as shown in illustration 2 Handle carefully as roll paper is heavy 2 6 Chapter2 Basic Operation 6 Lift up the Feeding Roller Cover 6 until it is locked 7 Hold on the sides of the media about 30mm from the top leading edge pulling the paper outwards to keep the lead edge taught Feed the media straight up in between the rollers noted Insert the leading part about 50mm of the roll paper between the Feeding Roller Cover 6 and the Roller 7 And then bring down the Feeding Roller Cover 6 8 Rewind the roll paper a little to remove any slack in the roll paper A NOTE The roll paper may
49. your preferable one optionally from these 14 levels 7 levels in Normal Mode and also 7 levels in SL Mode SL removes background The Copy Density is shown by both the Copy Density Indicator and SL Indicator The Copy Density Indicator has 7 selectable levels The density of copy becomes darker if you select the level on more right side On the contrary it becomes lighter if you select the one on more left side Also if you validate the SL Mode Strong Light Mode which removes background it becomes possible to select 7 more levels which belong to the lighter category than Normal Mode These 14 levels are consecutive SL Mode ON Normal Mode SL Mode OFF SL et SL Der C C CIC LI CI 02 C CI CA CA C CIO EEE Lightest Level Darkest Level Light Consecutive Dark Reference As the copy density becomes very light if you select the SL Mode it will be beneficial if the original has a very dark background like dark blue print 3 3 Chapter 3 Useful Function 1 Press the DARKER KEY 1 if you will make the copy density darker On the contrary press the LIGHTER Key 2 if you will make it lighter 2 Press the SL Key 3 if you will validate the SL Mode The SL Indicator 4 lights when validated You can validate and invalidate the SL Mode alternately whenever you press the SL Key 3 4 e TOI w CO I PLL LIGHTER DARKER C4 VELLUM TRACING Ca PLAIN PAPER MEDIA o Ce LI A
Download Pdf Manuals
Related Search