STINGER - BlackLight.com
Contents
1. To control your fixture in DMX mode follow the set up procedures on pages 7 9 as well as the set up specifications that are included with your DMX controller 3 Follow the instructions on page 12 to set the DMX address 4 For longer cable runs more than a 100 feet use a terminator on the last fixture 5 For help operating in DMX mode consult the manual included with your DMX controller Sound Active Mode This mode allows a single unit or several units linked together to run to the beat of the music 1 Press the MENU button until Soun is displayed and press ENTER 2 Press the UP or DOWN buttons to either activate sound active mode or deactivate and press ENTER The unit will now run to the beat of the music 3 The sound sensitivity can be adjusted by pressing the MENU button until Sens is displayed and then press ENTER Use the UP or DOWN buttons to adjust the sound sensitivity 0 being the least sensitive and 99 being the most sensitive Show Mode This mode allows a single unit or several units linked together to run to a built in program 1 Press the MENU button until Show is displayed and press ENTER 2 Press the UP or DOWN buttons to find your desired show and press ENTER The unit will now run your chosen built in program ADJ Products LLC www adj com Stinger Instruction Manual Page 13 Stinger Master Slave Set Up Master Slave Set Up This function will allow you to link up to2. 16 units together and operate without a controller In a Master Slave set up one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using standard XLR microphone cables daisy chain your units together via the XLR connector on the rear of the units Remem ber the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 Set the Master to your desired operating mode 3 Set the Slave unit s to address 001 4 The slave unit s will now follow the Master unit Stinger Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 10 fixtures maximum After 10 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures ADJ Products LLC www adj com Stinger Instruction Manual Page 14 Stinger DMX Traits Value Function AUTO RUN SOUND ACTIVE 0 9 BLACKOUT 10 39 SIX COLORS LED AUTO RUN 40 69 WHITE LEDS AUTO RUN 70 99 LASER AUTO RUN 100 129 AUTO RUN MIXING 130 159 SIX COLORS amp STROBING 160 189 LASER amp STROBING 190 219 LEDS LASER amp STRO
3. Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support adj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution This may cause eye damage Avoid looking directly into the light source Use sensible precaution ADJ Products LLC www adj com Stinger Instruction Manual Page 2 Stinger General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Stinger Features DMX 512 Protocol Compatible 10 DMX Channels RGBWAP Hex LED s Green amp Red Lasers 3 Operating Modes Sound Active Auto Run amp DMX Control Internal Microphone Digital Display for Address and Function Setting Power Cord Daisy Chain Stinger Warranty Registration The Stinger carries a 1 Year limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must pro
4. day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 1 Year Limited Warranty e ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches ADJ Products LLC www adj com Stinger Instruction Manual Page 18 Stinger Model Voltage LED Laser Power Draw Fuse Power Cord Daisy Chain Dimensions Weight Colors Duty Cycle DMX Channels Sound Active Working Position Warranty the power source Follow Us On t facebook com americandj twitter com americandj youtube com adjlighting Specifications Stinger 100V 240V 50 60Hz 6 x 5W RGBAWP Hex LEDs 8 x 3W White LEDs 4 9mW Red amp Green Laser Diodes 7OW 2A 10 Fixtures Max 12 L x 9 W x 9 75 H 304mm x 230 5mm x9 5mm 11 Ibs 5 kgs RGBAWP None 10 Yes Any Safe Secure Position 1 Year 365 Days Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu ww
5. BING 220 255 DMX MODE RGBWAP 0 9 BLACKOUT 10 198 COLOR MACROS 199 229 COLOR CHASE 1 226 255 COLOR CHASE 2 3 AUTO RUN 0 255 AUTO RUN SPEED SLOW FAST LED STROBE 0 9 NO STROBE LED STROBE SLOW FAST SOUND ACTIVE STROBING WHITE LEDS BLACKOUT WHITE OUTPUT POSITION WHITE OUTPUT CHASE WHITE LED STROBE 0 127 CHASE SLOW FAST NO STROBE 128 255 CHASE SLOW FAST STROBING LASERS BLACKOUT RED LASER GREEN LASER RED amp GREEN LASERS 10 244 245 255 ADJ Products LLC www adj com Stinger Instruction Manual Page 15 Stinger DMX Traits Value Function LASERS RED amp GREEN LASERS FLICKER GREEN amp RED LASERS FLICKER RED amp GREEN LASERS FLICKER SYNC RED amp GREEN LASERS ALTERNATE FLICKER LASER STROBE CONTROL NO STROBE STROBING SLOW FAST SOUND ACTIVE STROBING LED ROTATION NO ROTATION CLOCKWISE ROTATION SLOW FAST COUNTER CLOCKWISE ROTATION SLOW FAST LASER ROTATION 0 127 LASER PATTERNS 128 255 PATTERN CHASE SLOW FAST 130 169 170 209 210 249 250 255 0 9 10 244 245 255 128 255 ADJ Products LLC www adj com Stinger Instruction Manual Page 16 Stinger Fuse Replacement Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse
6. Rev 6 15 User Instructions IAVlec T SERES by ADJ 2015 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all ele
7. Sky contains high power laser devices internally Do not open the laser housing due to the potential exposure to unsafe levels of laser radiation The laser power levels if the unit is opened can cause instant blindness skin burns and fires STOP AND READ ALL LASER SAFETY DATA OPERATION INSTRUCTIONS AND LASER SAFETY The light source emitted from this product can potentially cause eye injury if not set up and used properly The light source emitted from a laser is very different from any other light sources with which you may be aware of Laser light is thousands of times more concentrated than any light from any other kind of light source This concentration of light can cause instant eye injuries primarily by burning the retina the back of your eyeball contatining cells that are sensitive to light Even if you cannot feel heat from a laser beam it can still poten tially injure or blind you or your audience Even very small amounts of laser beam light are potentially hazardous even at long distances Laser eye injuries can be sustained faster than you can blink Do not think that because this laser splits the laser beam into hun dreds of beams and that the laser beam is scanned out in high speed that an individual laser beam is safe for eye exposure This laser uses dozens of milliwatts of laser power Class 3B levels inter nally before it splits into multiple beams Class 3R levels Many of the individual beams are potentiall
8. anty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Excep
9. ctrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank you General Information Se ste Unpacking Thank you for purchasing the Stinger by ADJ Products LLC Every Stinger has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return this unit to your dealer without contacting customer sup port first Introduction The Stinger is a 10 channel DMX intelligent LED moon flower strobe amp laser fixture The fixture can operate in as a stand alone fixture or in a Master Slave configuration The Stinger has two operating modes sound active and DMX Control For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are
10. dress will now be displayed Press the UP or DOWN buttons to find your desired address Press ENTER to set your desired DMX address SHOW Show mode There are 7 show modes to choose from 1 Press the MENU button until Show is displayed press ENTER 2 The display will show one of seven auto show modes Use the UP or DOWN buttons to find your desired show and press ENTER to activate See the system menu on page 11 for the different shows SOUN Sound Active mode with adjustable sound sen Sitivity 1 Press the MENU button until Soun is displayed press ENTER 2 Use the UP or DOWN buttons to either turn sound activity On or Off and press ENTER 3 Press the MENU button until Sens is displayed and press ENTER Use the UP or DOWN buttons to adjust the sound sensitivity VER Use this function to display the Software version of the unit 1 Press the either the MENU button until VER is displayed press ENTER 2 The display will show the software version ADJ Products LLC www adj com Stinger Instruction Manual Page 12 Stinger Operation Universal DMX Control This function allows you to use a univer sal DMX 512 controller to control the patterns rotation and strobing A DMX controller allows you to create unique programs tailored to your individual needs 1 The Stinger is a 10 DMX channel DMX fixture See pages 15 16 for detailed description of the DMX values and traits 2
11. een frayed or broken Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power cords should be routed so they are not likely to be walked on pinched by items placed upon or against them Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 17 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when The power supply cord or the plug has been damaged Objects have fallen or liquid has been spilled into the unit The unit has been exposed to rain or water The unit does not appear to operate normally or exhibits a marked change in performance JOWS ADJ Products LLC www adj com Stinger Instruction Manual Page 4 Stinger Laser Warnings and Safety NON INTERLOCKED HOUSING WARNING The Royal
12. erted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable G X i to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Stinger Instruction Manual Page 8 Stinger Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting stan dard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 Stinger Installation The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibration and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can
13. g and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a sin gle controller as long as all fixtures and the controller are DMX com pliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Stinger can be controlled via DMX 512 protocol The Stinger is a 10 channel DMX unit The DMX address is set electroni cally using the controls on the back panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for da
14. hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp ADJ Products LLC www adj com Stinger Instruction Manual Page 9 Stinger Laser Warning Labels Stinger System Menu MENU FUNCTION Address setting press DOWN UP to choose 1 512 i Sh 1 Led show only Sh 2 Strobe show only Sh 3 Laser show only Sh 4 Led Laser mixed show E _E Sh_5 Led Strobe mixed show N OEA Sh 6 Laser Strobe mixed show Sh 7 Led Strobe Laser mixed show fa Sens 0 99 sound sensitivity from low to high Function Display Ap CF ay Sa I d 5 ON Sound mode ON run Sound mode 20 2 STINGER E aoun Siaries OFF Sound mode OFF run auto mode 0 0 __ EE Vers Vel 0 software version vee m S or CFI ceo ca dice POWER IN POWER OUT o j EE 5 O ADJ Products LLC www adj com Stinger Instruction Manual Page 10 ADJ Products LLC www adj com Stinger Instruction Manual Page 11 Stinger System Menu LCD DISPLAY LOCK The display will lock after 30 seconds Press and hold the MENU button for at least 10 seconds to unlock the display and access the menu ADDR DMX Address Setting 1 Press the either the MENU button until ADDR is displayed press ENTER 2 The current DMX ad
15. holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse Stinger Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing Use a brush to wipe down the cooling vents and fan grill Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days Clean the internal optics with glass cleaner and a soft cloth every 30 60 days Always be sure to dry all parts completely before plugging the unit back in D Ol Stinger Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the rear panel of the unit 2 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit Check the sound sen
16. s can be hazardous Never point a laser at aircraft this is a federal offense Never point un terminated laser beams into the sky Do not expose the output optic aperture to cleaning chemicals Do not use laser if the laser appears to be emitting only one or two beams Do not use the laser if the housing is damaged the housing is open or if the optics appear damaged in any way Never open the laser housing The high laser power levels inside of the protective housing can start fires burn skin and will cause instant eye injury Never leave this device running unattended The operation of a class 3R laser show is only allowed if the show is controlled by a skilled and well trained operator familiar with the data included in this manual The legal requirements for using laser entertainment products vary from country to country The user is responsible for the legal require ments at the location country of use Always use proper lighting safety cables when hanging lights and effects overhead ADJ Products LLC www adj com Stinger Instruction Manual Page 6 Stinger Set Up Power Supply The ADJ Stinger contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lightin
17. sitivity level N ADJ Products LLC www adj com Stinger Instruction Manual Page 17 Stinger Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warr
18. t to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180
19. ta input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro fessional sound and lighting stores Your cables should be made with a male and female XLR con nector on either end of the cable Also remember that DMX cable must be daisy chained and cannot i be split Figure 1 ADJ Products LLC www adj com Stinger Instruction Manual Page 7 Stinger Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Male Socket XLR Female Socket 1 Ground 2 2 Cold Figure 3 XLR Pin Configuration I I 2 Cold i 1 Ground i Pin 1 Ground Pin 2 Data Compliment negative i l I l 4 Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is ins
20. vide a copy of your proof of pur chase invoice Please contact ADJ customer support for a R A num O D T Stinger Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Stinger Instruction Manual Page 3 Stinger Safety Precautions LASER RADIATION AVOID DIRECT EYE EXPOSURE Maxi tput lt 5m avelength 405 532nm W Class Illa laser product This device complies with 21 CFR chapter l Subchapter J or CFR 1040 10 and 1040 11 Safety Issues This unit may pop the fuse if the maximum allotted load of 2 amps is reached e To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Do not attempt to oper ate this unit if the power cord has b
21. w adj com Tel 31 45 546 85 00 Fax 31 45 546 85 99
22. y hazardous to the eyes Do not that because the laser light is moving it is safe This is not true Nor do the laser beams always move Since eye injuries can occur instantly it is critical to prevent even the smallest possibility of any direct eye exposure In the laser safety regulation it is not legal to aim Class 3R lasers in areas which people can get exposed This is true even if it is aimed below people s faces such as on a dance floor Do not operate the laser without first reading and understanding all safety and technical data in this manual Always set up and install all laser effects so that all laser light is at least 3 meters 9 8 feet above the floor on which people can stand ADJ Products LLC www adj com Stinger Instruction Manual Page 5 Stinger Laser Warnings and Safety After setting up and before public use test laser to ensure proper function Do not use if any defect is detected Do not use if laser emits only one or two laser beams rather than dozens hundreds as this could indicate damage to the diffraction grating optic and could allow emission of higher laser levels above Class 3R Do not point lasers at people or animals Never look into the laser aperture or laser beams Do not point lasers in areas in which people can potentially get exposed such as uncontrolled balconies etc Do not point lasers at highly reflective surfaces such as windows mirrors and shiny metal Even laser reflection
Download Pdf Manuals
Related Search