Home

MVT380

1. Testing Tomorrow s Technology June 1 2011 Ms Iris Cai Meitek Inc 9550 Flair Dr Suite 520 El Monte CA 91731 Dear Ms Cai Enclosed please find the Meitek Inc file copy of the FCC Declaration of Conformity DoC report for the Model MVT380 manufactured by Shenzhen Meiligao Electronics Co Ltd Please keep a copy of this test report in your files as proof that the product has been tested Please carefully review Section 2 of the test report as this contains important information regarding DoC authorizations that you are expected to be responsible for Also to ensure your records contain all the proper documentation please be sure to add a copy of your User s Manual and Schematic and or Block Diagrams to this report If you have any questions please don t hesitate to call Thank you for your business Sincerely Alan Ghasiani Consulting Engineer President 3505 Francis Circle Alpharetta GA 30004 PH 770 740 0717 Fax 770 740 1508 www ustech lab com Testing Tomorrow s Technology FCC Declaration of Conformity DoC Report for the Meitek Inc 9550 Flair Dr Suite 520 El Monte CA 91731 GPS Tracker Model MVT380 Manufactured by Shenzhen Meiligao Electronics Co Ltd 6 F West Tower Cafu plaza Sheraton No 5 Guihua Rd Futian Bonded Zone Shenzhen China 518033 Test Date s May 23 2011 Issue Date June 1 2011 UST Project No 11 0096 3505 Francis Circle Alpharetta GA 30004 PH
2. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase as described in 2 925 d of this chapter Permanently affixed means that the label is etched engraved stamped silkscreened indelibly printed or otherwise permanently marked on a permanently attached part of the equipment or ona nameplate of metal plastic or other material fastened to the equipment by welding riveting or a permanent adhesive The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable Page 14 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 3 System Test Configuration 3 1 Characterization of Sample Tested The sample used for test was received on May 16 2011 in good condition 3 2 Justification The system was configured for testing in a typical fashion the same as a customer would normally use it 3 3 EUT Exercise Software The EUT was designed to exercise the various system components in a manner similar to typical use The software pre contained on the EUT automatically loaded itself once the EUT was plugged into the computer A Graphic User Interface GUI was displayed and was ready to tune to
3. 770 740 0717 Fax 770 740 1508 www ustech lab com Page 1 of 33 Testing Tomorrow s Technology certify that am authorized to sign for the test facility and that all of the statements in this report and in the Exhibits attached hereto are true and correct to the best of my knowledge and belief US Tech Agent Responsible For Test By Name Alan Ghasiani Title Consulting Engineer President Date June 1 2011 This report shall not be reproduced except in full This report may be copied in part only with the prior written approval of US Tech The results contained in this report are subject to the adequacy and 3505 Francis Circle Alpharetta GA 30004 PH 770 740 0717 Fax 770 740 1508 www ustech lab com Page 2 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 TABLE OF CONTENTS 1 GENERAL INFORMATION 5 1 1 Product Description 5 1 2 Related Submittal s Grant s 5 1 3 Tested System details 6 Table 1 EUT and Peripherals 6 Table 2 Detail of WO Cables Attached to EUT 7 1 4 Test Methodology 8 1 5 Test Facility 8 1 6 Test Equipment 9 Table 3 Test Equipment 9 Figure 1 NVLAP Certificate 10 2 PRODUCT LABELING 11 2 1 Responsibilities 11 2 2 Retention of Records 12 2 3 Compliance Information 12 2 4 Manual 13 2 5 Information to User 13 2 6 Special Ac
4. Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 1 GENERAL INFORMATION 1 1 Product Description The Equipment Under Test EUT is the Meitek Inc Model MVT380 manufactured by Shenzhen Meiligao Electronics Co Ltd The EUT is a GPS Tracking Device 1 2 Related Submittal s Grant s The EUT is subject to the following authorizations a Certification or DoC as a receiver The EUT contains an FCC Certified Transmitter Module bearing FCC ID XMR 16182009002 The information contained in this report is presented for the DoC authorization for the EUT Page 5 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 1 3 Tested System Details Table 1 EUT and Peripherals SERIAL PERIPHERAL MODEL NUMBER NUMBER FCC ID CABLES MANUFACTURER P D Contains FCC Shenzhen MVT380 ID 8 U power cable Meiligao XMR A U USB cable Electronics CO 16182009002 LTD EUT GPS Antenna N A N A 10 U antenna cable GSM Device N A N A 10 U antenna cable DC power Supply HY1803D N A 6 U power cord TekPower S Shielded U Unshielded Page 6 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date J
5. KHz to 30 MHz Conducted Emissions Test Bv Test Part 15B Verification Client Meitek Inc S S Project 11 0096 EUT MVT380 Frequen Test Data AF CA Peak Results Average Margin Detector cy dBuV AMP dBuV Limits dBuV dB Used MHz dB EUT is DC powered This test is not required per FCC Part 15 107 Paragraph d Test Date May 23 2011 Tested by Signature Name Sina Sobhaniyan Page 23 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 6 Radiated Emissions Data 6 1 Test Description Radiated emissions were evaluated from 30 MHz to 12 5 GHz Measurements were made with the analyzer s bandwidth set to 120 kHz for measurements made less than 1 GHz and 1 MHz for measurements made greater then or equal to 1 GHz The following data lists the significant emission frequencies measured levels correction factor includes cable and antenna corrections the corrected reading plus the limit Page 24 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 6 Radiated Emissions Data 47 CFR 15 109a Table 5 Measurements from 30 MHz to 1 GHz Radiated Emissions _ Test Part 15B eres Soe Client Meite
6. to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 2 5 INFORMATION TO USER 47CFR 15 21 The user s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 6 SPECIAL ACCESSORIES 47CFR 15 27 c Accessory items that can be readily obtained from multiple retail outlets are not considered to be special accessories and are not required to be marketed with the equipment The manual included with the equipment must specify what additional components or accessories are required to be used in order to ensure compliance with this part and it is the responsibility of the user to provide and use those components and accessories Page 13 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model
7. 00Z SZ021 DAVOS Psepuels seuoneuieju paziuboses ay ym aouppso22e ul paypasaoe si Arojes0ge SI SNOLLVOINDIWNWOOUTSEAL ANV ALITIELLVdWOO OLLANDVWOULOATA JOJ UOHeYPAIIOYy JO 2009S ay UO Dale SANASS MISAS JO WwesGol4 LOup Heike GE Auejunjo BUEN ey Aq PIPI st y9 enaydyy Pap sn O 79L00T AGOD HVT dV IAN S002 SZOZL DAI OSI 0 UONE PSID9VY JO oui CUAN ABojouyse pue spuepue s jo 3N ysuj jeEUOHeN BIBWILUOD JO JuOUedag Sage payun Page 10 of 33 Figure 1 NVLAP Certificate US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 2 Product labeling FCC DECLARATION OF CONFORMITY DoC LABELING INFORMATION The following information is applicable to products or systems which have been tested for compliance and the responsible party is showing approval by a Declaration of Conformance DoC This labeling information is not appropriate for equipment that is assembled from modular component parts that have been independently approved 2 1 RESPONSIBILITIES 47CFR 2 1073 a The responsible party as defined in 2 909 must warrant that each unit of equipment marketed under a Declaration of Conformity is identical to the unit tested and found acceptable with the standards and that the records maintained by the responsible party continue to reflect the equipment being
8. ADS 43 2 1 Page 30 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 4 EUT Photo Rear View Page 31 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 5 EUT Photo PCB Top View Page 32 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 6 EUT Photo PCV Bottom View Page 33 of 33
9. AM FM radio This is the normal mode of operation 3 4 Special Accessories All interface cables used for compliance testing are shown in Table 2 3 5 Equipment Modifications No modification was made by US Tech to bring the EUT into compliance with FCC Part 15 Class B requirements Page 15 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 3 6 Test Results The worst case radiated emission from 30 MHZ to 1000 MHZ was 7 2 dB below the Class B limit at 48 9410 MHz All other radiated emissions were at least 7 4 dB below the Class B limit 3 7 Measurement Uncertainty Radiated Emissions Measurement Distance of 3 m The measurement uncertainty with a 95 confidence level for this test using a Biconnical Antenna is 5 3 dB The measurement uncertainty with a 95 confidence level for this test using a Log Periodic Antenna is 5 1 dB The measurement uncertainty with a 95 confidence level for this test using a double ridge horn antenna is 2 5 dB II The data listed in this test report may exceed the test limit because it does not have enough margin to meet the measurement uncertainty interval gt lt The data listed in this test report has enough margin to meet the measurement uncertainty interval Conducted Emissions Measurement Uncertainty within a 95 con
10. MVT380 FCC DECLARATION OF CONFORMITY DoC LABELING INFORMATION CONT 2 7 GENERAL LABELING REQUIREMENTS FOR DoC 47CFR 15 19 b 1 The label shall be located in a conspicuous location on the device and shall contain the unique identification described in 2 1074 of this chapter and the following logo i If the product is authorized based on testing of the product or system or Trade name Model number ii If a personal computer is authorized based on assembly using separately authorized components in accordance with 15 101 c 2 or c 3 and the resulting product is not separately tested Trade name Model number Assembled from tested components Complete system not tested 2 Label text and information should be in a size of type large enough to be readily legible consistent with the dimensions of the equipment and the label However the type size for the text is not required to be larger than eight point 3 When the device is so small or for such use that it is not practicable to place the statement specified under paragraph b 1 of this section on it such as for a CPU board or a plug in circuit board peripheral device the text associated with the logo may be placed in a prominent location in the instruction manual or pamphlet supplied to the user However the unique identification trade name and model number and the logo must be displayed on the device 4 The label shall not be a stick on paper label
11. cessories 13 2 7 General Labeling 14 3 SYSTEM TEST CONFIGURATION 15 3 1 Characterization Of Sample Received 15 3 2 Justification 15 3 3 EUT Exercise Software 15 3 4 Special Accessories 15 3 5 Equipment Modifications 15 3 6 Test Results 16 3 7 Measurement Uncertainty 16 3 8 Configuration Of Tested System 17 Figure 2 Test Configuration 17 Page 3 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 4 TEST CONFIGURATION PHOTOS 18 4 1 Radiated Emissions Configuration Photos 18 Figure 3 Radiated Emissions Front View 19 Figure 4 Radiated Emissions Rear View 30 200 MHz 20 Figure 5 Radiated Emissions Rear View 200 1000 MHz 21 Figure 6 Radiated Emissions Rear View 1 12 5 GHz 5 POWERLINE CONDUCTED EMISSION DATA 22 5 1 Test Description 22 Table 4 Conducted Emissions 150 KHz to 30 MHz 23 6 RADIATED EMISSION DATA 24 6 1 Test Description 24 Table 5 Measurements 30 MHz to 1 GHz 25 Table 6 Measurements gt 1GHz 26 6 2 Field Strength Calculation 27 7 PHOTOS OF TESTED EUT 28 7 1 EUT Photo Top View 28 7 2 EUT Photo Bottom View 29 7 3 EUT Photo Front View 30 7 4 EUT Photo Rear View 31 7 5 EUT Photo PCB Top View 32 7 6 EUT Photo PCB Bottom View 33 Appendices 1 Block Diagram and or Schematics 2 Users Manual Page 4 of 33 US Tech Test Report Part 15
12. fidence level for this test is 2 8 dB C The data listed in this test report may exceed the test limit because it does not have enough margin more than 2 8 dB to meet the measurement uncertainty interval C The data listed in this test report has enough margin to meet the measurement uncertainty interval The EUT is DC powered and does not connect to the AC mains therefore this test was not applicable Page 16 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 3 8 Configuration Of Tested System The EUT was set up as follows Shenzhen Meiligao Electronics GPS Co Ltd Antenna EUT 60Hz upply Antenna S Shielded U Unshielded Figure 2 Configuration of Tested System Page 17 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 4 Test Configuration Photos 4 1 Radiated Emissions Configuration Photos Figure 3 Radiated Emissions Front View Page 18 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 4 1 Test Phot
13. his chapter that the product complies with part 15 of this chapters and 3 The identification by name address and telephone number of the responsible party as defined in 2 909 The responsible party for a Declaration of Conformity must be located within the United States The compliance information statement shall be included in the user s manual or as a separate sheet Page 12 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 FCC DECLARATION OF CONFORMITY DoC LABELING INFORMATION CONT 2 4 MANUAL 47CFR 15 105 For a Class B digital device or peripheral the user s instructions must include the following or similar statement placed in a prominent location in the text of the manual Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference
14. igao Electronics Co Ltd Model MVT380 6 2 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain if any from the measured reading The basic equation with a sample calculation is as follows FS RA CF AG where FS Field Strength RA Receiver Amplitude CF Correction Factor Antenna Factor Cable Loss AG Amplifier Gain Assuming a receiver reading of 88 0 dBm and a correction factor of 11 8 dB the following calculation would apply FS uV m Antilog H 88 0 11 8 107 20 34 7 Page 27 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 Photos of the Tested EUT 7 1 EUT Photo Top View Page 28 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 2 EUT Photo Bottom View MEITEK INC Model MVT380 Location L3 16 11 Page 29 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 7 3 EUT Photo Front View PowerGND
15. k Inc Project 11 0096 EUT MVT380 Frequency Test Data T Margin Detector oat Used Distance E GEI _ Polarization GI Measurements were made over the frequency range of 30 MHz 1GHz 110 7630 14 80 14 39 29 19 43 5 3m VERT 143 PK 2249540 16 30 IL 1464 30 94 460 3m HORZ 151 PK 221 5140 14 40 14 60 29 00 46 0 3m VERT 17 0 PK 525 2550 15 90 22 68 38 58 46 0 3m VERT 7 4 PK Sample Calculations at 48 9410 MHz 20 50 dBuV 12 30 dB m 32 80 dBuV m Test Date May 23 2011 Tested by Signature Name Sina Sobhaniyan Page 25 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 6 Radiated Emissions Data 47 CFR 15 109a Table 6 Measurements above 1 GHz Radiated Emissions _ Test Part 15B ce aes or Client Meitek Inc Project 11 0096 EUT MVT380 Test Data Kesis fard e EAA Margin Detector dBuV Distance dB vice Polarization Measurements were made over the frequency range of 1 GHz to 12 GHz No emission was found within 20 dB of the limit Test Date May 23 2011 Tested By Signature Name _ Sina Sobhaniyan Page 26 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meil
16. l provisions for the Declaration of Conformity including having test data on file demonstrating that the product continues to comply with all of the applicable technical standards Page 11 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 FCC DECLARATION OF CONFORMITY DoC LABELING INFORMATION CONT 2 2 RETENTION OF RECORDS 47CFR 2 1075 For each product subject to a Declaration of Conformity the responsible party shall maintain the records listed below 1 A record of the original design drawings and specifications and all changes that have been made that may affect compliance with the requirements of 2 1073 2 A record of the procedures used for production inspection and testing if tests were performed to insure the conformance required by 2 1073 Statistical production line emission testing is not required 3 A test report which satisfies the requirements of 2 1075 2 3 COMPLIANCE INFORMATION 47CFR 2 1077 If a product is tested and authorized under a Declaration of Conformity a compliance information statement shall be supplied with the product at the time of marketing or importation containing the following information 1 Identification of the product e g name and model number 2 A statement similar to that contained in 15 19 a 3 of t
17. o of Radiated Emissions cont d Figure 4 Radiated Emissions Rear View Test Setup from 30 200 MHz Page 19 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 4 1 Test Photo of Radiated Emissions cont d Figure 5 Radiated Emissions Rear View Test Setup from 200 1000 MHz Page 20 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 4 1 Test Photo of Radiated Emissions cont d Figure 6 Radiated Emissions Rear View Test Setup from 1 12 5 GHz Page 21 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 5 Power Line Conducted Emissions Data 5 1 Test Description EUT is DC powered This test is not required per FCC Part 15 107 Paragraph d Page 22 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 5 Power Line Conducted Emissions Data 47 CFR 15 107 Table 4 Conducted Emissions 150
18. produced under the Declaration of Conformity within the variation that can be expected due to quantity production and testing on a statistical basis b The responsible party if different from the manufacturer may upon receiving a written statement from the manufacturer that the equipment complies with the appropriate technical standards rely on the manufacturer or independent testing agency to determine compliance However the test records required by 2 1075 shall be in the English language and shall be made available to the Commission upon a reasonable request in accordance with the provisions of 2 1076 c In the case of transfer of control of the equipment as in the case of sale or merger of the responsible party the new responsible party shall bear the responsibility of continued compliance of the equipment d Equipment shall be retested to demonstrate continued compliance with the applicable technical standards if any modifications or changes that could adversely affect the emanation characteristics of the equipment are made by the responsible party The responsible party bears responsibility for the continued compliance of subsequently produced equipment e If any modifications or changes are made by anyone other than the responsible party for the Declaration of Conformity the party making the modifications or changes if located within the U S becomes the new responsible party The new responsible party must comply with al
19. rical and Electronic Equipment in the Range of 9 kHz to 40 GHz 2003 paragraph 7 for conducted emissions and paragraph 8 for radiated emissions Conducted and radiated emissions data were taken with the test receiver or spectrum analyzer s resolution bandwidth adjusted to 9 kHz and 120 kHz respectively All measurements are peak unless stated otherwise The video filter on the spectrum analyzer was OFF throughout the evaluation process Interconnecting cables were manipulated as necessary to maximize emissions The EUT and Peripherals Table describe other instruments and accessories used to evaluate this product 1 5 Test Facility For equipment authorized under a Declaration of Conformity DoC the party performing the measurements shall be accredited for performing such measurements by an authorized accreditation body US Tech is approved by an authorized accreditation body and has been issued a Certificate of Accreditation A copy of this certificate is shown on the following page The open area test site and conducted measurement facility used to collect the radiated data is located at US Technologies measurement facility at 3505 Francis Circle Alpharetta GA This site has been fully described and registered with the FCC under designation Number US5117 Additionally this site has also been fully described and submitted to Industry Canada IC and has been approved under file number 2982A 1 Page 8 of 33 US Tech Test Report Part 15 Declara
20. tion of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 1 6 Test Equipment Table 3 Test Equipment INSTRUMENT MODEL MANUFACTURER SERIAL DATE OF LAST NUMBER NUMBER CALIBRATION SPECTRUM HEWLETT ANALYZER 8566B PACKARD 2410A00109 10 29 10 HEWLETT PREAMPLIFIER 8447D PACKARD 2944A07436 09 07 10 SPECTRUM HEWLETT ANALYZER 8593E PACKARD 3205A00124 10 18 10 HEWLETT PREAMPLIFIER 8449B PACKARD 3008A00480 10 21 10 BICONICAL ANTENNA 3110B EMCO 9306 1708 4 29 11 LOG PERIODIC 1 22 10 ANTENNA SC EMGO 2 years HORN 2 9 2010 ANTENNA SAS 571 A H Systems 2 years CALCULATION PROGRAM Note The calibration interval of the above test instruments is 12 months unless stated otherwise and all calibrations are traceable to NIST USA Page 9 of 33 11 0096 June 1 2011 Meitek Inc MVT380 Part 15 Declaration of Conformity DoC Shenzhen Meiligao Electronics Co Ltd US Tech Test Report Report Number Issue Date Customer Manufacturer Model 82 10 6002 ASW DLOYIAN ae Try ABOjOUj9G PUE SPSEPUB S JO GPIPISU LUOMEA GY IQ F ao Sap APOI D a Le K Ee S S O 90 110Z YNONN 10 20 0107 D E K Pa Dau 6002 Avenues pajep anbiunwiwiod 2 2 T OS Hal oi 13434 wajshs juewebeuew Ajyenb Aroyeioge 8 jo uonesado ay pue ach pauyap 6 JO A2duajadiuod Jeu SajessSuOWwap VONEPPAsOe Siy G
21. une 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 1 3 Tested System Details cont d Table 2 Detail of I O Cables Attached to EUT DESCRIPTION OF DETAILS OF CABLE CABLE CABLE LENGTH Manufacturer and Part Number EUT Shenzhen SES Electronics Co Ltd Termination Backshell Manufacturer and Part Number Shenzhen Meiligao Electronics Co Ltd GPS Antenna Cable Shield Type Shield Type of Termination Backshell CND CND CND Manufacturer and Part Number Shenzhen Meiligao Electronics Co Ltd GSM Antenna Cable Shield Type Shield Type of Termination Backshell CND CND Manufacturer and Part Number Shenzhen Meiligao Electronics Co Ltd Shield Type Shield Type of TE Pen Shield Type Shield Termination Type of Backshell N A None N A None N A Not Applicable F Foil 360 360 PS Plastic Shielded B Braided P Pigtail Drain Wire PU Plastic Unshielded 2B DoubleBraided CND Could Not Determine MS Metal Shielded CND Could Not Determine MU Metal Unshielded Page 7 of 33 US Tech Test Report Part 15 Declaration of Conformity DoC Report Number 11 0096 Issue Date June 1 2011 Customer Meitek Inc Manufacturer Shenzhen Meiligao Electronics Co Ltd Model MVT380 1 4 Test Methodology The EUT was configured as shown in the following block diagram and photographs The Test Sample was tested per ANSI C63 4 Methods of Measurement of Low Voltage Elect

MVT380

Contents

Download Pdf Manuals

Related Search

Related Contents