Waterwise 7000™
Contents
1. Cycle Production Operating Operation Model V Volts Hz Hertz We Watts AMPS Time Rate Pressure Temperature d 1 gallon gallons per day 40 110 F 7050 120V 60Hz 1200W 10AMPS 2 75 hrs 9 gpd 20 80 psi 5 45 C 40 110 F 7052 230V 50Hz 1100W 4 8AMPS 2 75 hrs 9 gpd 20 80 psi 5 45 C FIGURE A Electric Cord Statement tiller when not in use CAUTION Your Distiller has a short cord as a safety precaution to prevent injury or property damage resulting from pulling tripping or becoming entangled with the cord Do not allow children to be near this Distiller without close adult supervision If you must use an extension cord with this Distiller the cord must be arranged so that it will not drape or hang over the edge of a countertop or tabletop where it can be pulled on by children or tripped over To prevent electric shock injury or fire the electrical rating of the extension cord you use must be the same as or more than wattage of the Distiller wattage is indicated on the louvered cover of the Distiller Plug Distiller into rated voltage AC grounded electric outlet ONLY rated voltage found on louvered cover The cord has a three prong plug which mates with a standard three prong grounded wall outlet Do not cut or remove the third prong from the plug If an adapter is used be sure adapter wire and wall outlet are grounded If there is any doubt as to whether the outlet is properly grounded check with a licensed el2. mOOW gt Fan motor or fan microswitch is defective Water does not boil A Boiler tank is not mounted on lift spring bracket B Make sure tank plug is fully inserted into receptacle C Reset button on side of boiler tank tripped breaking the circuit Be sure boiler tank is clean Press Reset button If Reset button continues to trip thermal overload defective D Heating element is defective Inlet water valve does not shut off A Boiler tank is not mounted on lift spring bracket B Water microswitch is defective C Inlet water valve is defective Water leak in boiler tank area Hinged A Lid is not properly aligned or black knob not tightened Cover B Boiler tank gasket is defective or not properly fitted Black a on tank Knob C O ring in knob is missing or defective D O ring around heating element is defective Distilled water has an unusual taste A Contaminated carbon filter s Replace the pre and or post filter s B Boiler needs cleaning page 10 C Boiler overfilling see 5 above Inlet water valve does le ae not shut off Janig D Reservoir needs cleaning page 10 Water overflows reservoir A Float microswitch is defective Plug Receptacle Indicator z Line N TNN AN Sonoran Power B Inlet water valve is defective Boiler gt Fan Switch Taik A Switch Condensation on outside of reservoi
3. www waterwise com E mail service waterwise com 1990 Waterwise Inc Printed in USA Form 7801 e L20120WT e Rev 02 11
4. Installation NOTE All state provincial and local laws and regulations must be followed in the installation and use of your distiller Turn inlet elbow fitting assembly clockwise onto inlet water valve fig H Cut the inlet tubing square and remove any burrs Firmly push the tubing into the elbow fitting Pull on the tubing to check that it is secure inside the fitting If secure insert red clip between fitting body and collet IMPORTANT Ifyou will be using a prefilter install it now See Prefilter Installation Instructions form 7812 CAUTION DO NOT position tubing over sharp objects which could cut tubing or near any equipment appliances etc that generate excessive heat which could melt tubing Saddle Valve The supplied saddle valve taps into a COLD water pipe under your kitchen sink near washing machine or other suitable location and fits 3 8 outside diameter OD up to 1 1 4 OD soft or hard tubing or pipe Elbow Fitting Assembly Installing Saddle Valve on Copper Pipe A 1 Ficure I IMPORTANT DO NOT use a hot water supply Assemble saddle valve on COLD water pipe with two 2 bolts fig I Be sure piercing lance does not protrude beyond the sealing washer Tighten bolts evenly with saddle clamp brackets parallel DO NOT OVERTIGHTEN Slide compression nut over end of 1 4 tubing Place white compression ring on tubing Be sure wide end of ring is facing compressio
5. This is typical The carbon dust is formed as a result of production packag ing and shipping of filter cup NOTE Set prepared filter cup aside until reservoir has been steam sterilized page 9 Replace Filter Cup The filter cup should be replaced every two months or after 60 80 gallons of water processed whichever comes first Replace more often should the distilled water begin Figure E to have an unwanted taste or odor Order replacement filters from the outlet where you purchased your Distiller NOTE This Distiller meets the listing require ments of Underwriters Laboratories Inc but they have not investigated the physiological effect of the use of these carbon filters beneficial or otherwise Operational maintenance and replacement requirements are essential for this product to perform as advertised Placing Distiller on Reservoir Set Distiller on top of reservoir fig E Be sure to locate louvered half where fan motor is located over post filter end of reservoir DO NOT install post filter until reser voir has been sterilized Louvered Cover Hinged Cover AW nm gzs eaea e gt ISS 22422z SSS C2222 SSS C2222 SSS 222224 SS 5 EEE 5 gI BABE SSS ZAZ SSS SSS 2 SSS Z SS BA Reservoir Post Filter Holder Remove and Clean Boiler Tank 1 Unplug boiler tank cord from receptacle fig G 2 Unscrew and remove black knob by turni
6. the best location A FiGure B A properly rated voltage AC grounded electric outlet is required rated voltage label located on louvered cover If uncertain whether the outlet is properly grounded have it checked by a quali fied electrician A well ventilated area is necessary to properly dissipate heat produced during the distillation process When using your Distiller provide adequate air space above and on all sides for air circulation especially louvered half where fan motor is located Keep at least 4 6 inches from walls or cabinets Locate your Distiller near a pressurized water source Twenty five 25 feet of 1 4 inlet tubing and a saddle valve are included to tap into a COLD water pipe for automatic fill Optional water connector available utility faucet con nection for 3 4 hose thread type faucet The location should also provide easy and con venient dispensing of the distilled water Reservoir Plug Black Plastic Jam Nut e For your added convenience the optional Remote Faucet Pump System provides distilled water on tap and to an automatic refrigerator icemaker PREPARING FOR FIRST TIME USE Initial Cleaning Clean inside of reservoir with either hydrogen peroxide or a paste of baking soda and water Rinse thoroughly Reservoir Assembly 3 Gallon Model 1 To install black adhesive backed feet to bottom corners of reservoir position reservoir so that it sits open side down Peel and sti
7. No dealer distributor agent representative or other person is authorized to extend or expand this warranty Waterwise is not responsible or liable for personal injury property damage or incidental or consequential dam ages arising out of or in connection with the use or performance of the product or other damages with respect to loss of use or costs of removal installation or reinstallation Waterwise will at its option replace or repair the defective part s without charge provided they are returned transportation prepaid by owner to an authorized service facility or to the address below Enclose a letter de scribing the problem copy of dated proof of purchase and your name address and daytime telephone number This limited warranty does not guarantee uninterrupted service Repair or replacement as provided under this warranty is the exclusive remedy of the purchaser This limited warranty is in lieu of all other warranties expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular use or purpose This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Outside the United States a different warranty may apply For details please contact your authorized Waterwise distributor ANTE WISE 3608 Parkway Blvd Leesburg Florida 34748 9399 352 787 5008 Fax 352 787 8123
8. USE amp CARE GU Waterwise 7000 Water Distiller MEMBER we Sai ASSOCIATION See important safeguards on page 2 An exclamation point within an equilateral triangle is intended to alert user to the presence of important operating and maintenance instructions in the literature accompanying the appliance A lightning bolt within an equilateral triangle is intended to alert user to risk of injury from electric shock user to risk of injury from boiling water and or escaping steam 5 Water and steam vapor within an equilateral triangle is intended to alert A IMPORTANT SAFEGUARDS A person who has not read and understood all operating and safety instructions is not qualified to operate this appliance When using this appliance always adhere to basic safety precautions including READ ALL INSTRUCTIONS BEFORE USE FOR COMMERCIAL AND HOUSEHOLD USE l Operate indoors on a dry level well supported stable surface DO NOT use outdoors DO NOT operate in a moving vehicle DO NOT allow children to be near Distiller with out close supervision Boiling water will scald if spilled on skin Warn other users of possible dan gers from boiling water and or escaping steam Never remove boiler while Distiller is operating Let cool at least one hour after a cycle is finished or interrupted Boiling water or steam can cause severe burns DO NOT change position or location of Distiller while it is opera
9. an authorized ser vice facility for examination repair or replacement Unplug from wall outlet when not in use and before cleaning This Distiller is recommended for use with potable water only DO NOT attempt to make safe drinking water from non potable water source DO NOT use briny sea water as this will dam age certain components and will void warranty Keep Distiller in a well ventilated area and away from other heat sources providing adequate air space at least 4 6 inches from walls or cabinets DO NOT place on or near a hot gas or electric burner or in a heated oven DO NOT store or stack anything on top of or against sides of Distiller while in operation DO NOT operate Distiller without water in the boiler tank Permanent damage may occur This Distiller requires no special care other than periodic filter replacement page 6 and general cleaning page 10 If servicing becomes necessary please contact your authorized dealer or qualified service facility There are NO user serviceable parts See warranty for service details Make sure Power and Fan switches are off and gasket boiler tank and lid are properly secured before plugging in Distiller DO NOT use the Distiller for other than the intended use This product was tested and certified by the Water Quality Association against WQA S 400 for the reduction of TDS Total Dissolved Solids and structural integrity
10. and then tapping into place using a rubber mallet fig D Install the four casters into holes provided on caster support assembly Tighten securely Turn reservoir over so that it stands open side up fig D Decide if you wish to mount sight gauge faucet on either the wide or narrow side of the reservoir Install sight gauge faucet by placing one rubber washer flat side against outside of reservoir onto threaded end of the faucet Insert faucet through the mounting hole in reservoir From INSIDE reservoir secure with black plastic jam nut DO NOT OVERTIGHTEN Inspect to make sure sight gauge is straight Position sight gauge retaining bracket over sight gauge and hook it over edge of reservoir fig D Black Plastic Sight Gauge Jam Nut Retaining Bracket LL Figure D ee E OP IJ Sight ij Gauge m OF axl 508 ee za Sight ve has Gauge Reservoir a w Faucet Plug f BS o N aa R Rubber Washer b g MITAS Caster Support Assembly locking Swivel Q ee Black Plastic Caster D End Cap 5 NOTE If installing a Remote Faucet Pump System please refer to Remote Faucet Pump System Use and Care Guide in order to complete reservoir assembly 6 Install reservoir plug by placing one rubber washer flat side against outside of reservoir onto thread ed end of plug and inserting it into the remaining hole in reservoir fig D From INSIDE reservoir secure
11. ck adhesive feet provided to outside corners of reservoir bottom To ensure better adhesion wipe bottom corners of reservoir with alcohol before installing feet Turn reservoir over so that it sits open side up fig B 2 Decide if you wish to mount sight gauge faucet on either the wide or narrow side of the reservoir Install sight gauge faucet by placing one rubber washer flat side against outside of reservoir onto threaded end of the faucet Insert faucet through the mounting hole in reservoir From INSIDE reservoir secure with black plastic jam nut DO NOT OVERTIGHTEN Inspect to make sure sight gauge is straight 3 Install the reservoir plug by placing one rubber washer flat side against outside of reservoir onto threaded end of plug and inserting it into the remaining hole in reservoir fig B From INSIDE reservoir secure with black plastic jam nut DO NOT OVERTIGHTEN POVE Sight Gauge Sight Gauge Faucet FIGURE C Reservoir Assembly 8 Gallon Model To install plastic feet place reservoir on the floor open side down so legs are pointing up Install a plastic foot on bottom of each leg Turn reservoir over so that it stands open side up fig C Decide if you wish to mount sight gauge faucet on either the wide or narrow side of the reservoir Install sight gauge faucet by placing one rubber washer flat side against outside of reservoir onto threa
12. ded end of the faucet Insert faucet through the mounting hole in reservoir From INSIDE reservoir secure with black plastic jam nut DO NOT OVERTIGHTEN Inspect to make sure sight gauge is straight Position sight gauge retaining bracket over sight gauge and hook it over edge of reservoir fig C NOTE If installing a Remote Faucet Pump System please refer to Remote Faucet Pump System Use and Care Guide in order to complete reservoir assembly Install reservoir plug by placing one rubber washer flat side against outside of reservoir onto thread ed end of plug and inserting it into the remaining hole in reservoir fig C From INSIDE reservoir secure with black plastic jam nut DO NOT OVERTIGHTEN Sight Gauge Retaining Bracket Black Plastic Jam Nut Ba Sight i2 A Gauge do D aT A Sight Gauge Reservoir hi Plug _ amp Rubber g Washer p NY ie Seton Black Plastic Foot Reservoir Assembly 12 Gallon Model To install casters place reservoir on the floor open side down so legs are pointing up Install both caster support assemblies onto reser voir legs by inserting the raised steel tabs on caster support assembly into open end of legs Securely fasten caster support assemblies in place using bolts provided fig D Install the four black plastic end caps by insert ing an end cap into each open end of the caster support assembly by hand
13. ectrician Unplug the Dis SAVE THESE INSTRUCTIONS How It Works This Distiller produces purified water by using the oldest most effective method of water treatment steam distillation When the Distiller is operating the water temperature rises to 212 F 100 C killing bacteria cysts and viruses that may be present As the boiling water converts to steam Q it rises and leaves behind dead microbes dissolved solids salts heavy metals and other substances Low boiling light gases that may be present are discharged through the gaseous vent Steam is then cooled in the stainless steel condenser turning it into high quality water Distilled water percolates through a final polishing coconut shell carbon filter to enhance qual ity by adsorption of VOCs volatile organic compounds and is then collected in the stainless steel reservoir UNPACKING The Waterwise 7000 is packaged to prevent damage in shipping If any damage is found immediately notify the carrier who made delivery and or the company from which it was purchased After opening box and removing Distiller lift hinged cover to boiler tank area and remove ALL packing material NOTE Each Distiller is individually tested to ensure high quality standards Water residue deposits may be evident in the boiler tank as a result of this quality control procedure INSTALLATION REQUIREMENTS Several factors should be considered when choosing
14. ed to unit fig F Empty the contents and rinse any loose scale deposits from boiler IMPORTANT DO NOT immerse boiler tank in water or other liquid Remount boiler tank onto lift spring bracket fig F Check for proper mounting by pressing boiler tank down It should spring up when released Be sure to fully insert boiler tank cord plug into receptacle so the indicator line is NOT visible A loose connection may damage tank cord and receptacle thus resulting in Distiller failure Plug main power cord into wall outlet press Fan and Power switches to ON position Approximately every three to four weeks a thorough removal of scale deposits may be necessary Cleaning frequency will vary depending on usage and water conditions To dissolve scale deposits remove empty and rinse boiler tank Fill with approximately 1 gallon of KLEENWISE solution or another safe mineral solvent Be sure to follow descaling instructions on product label Descaling time will vary depending on strength of descaler solvent and amount of scale buildup After cleaning rinse boiler tank thoroughly and remount DO NOT remount boiler tank until cleaning proce dure is complete NOTE DO NOT use abrasive cleaners caustic acids or steel wool pads DO NOT scrape or chisel scale from boiler tank Condensing Coil The condensing coil fins should be cleaned periodically A dirt dust deposit will decrease efficiency of Distiller Condens
15. es are off before plugging power cord into outlet fig G Plug the three pronged power cord into a properly rated voltage AC grounded electric outlet only Press the two switches Fan and Power to the ON position red indicator showing Boiler tank will start to fill with water 6 As the water level rises in boiler tank the fan and heating element will automatically turn on The water inlet valve controls flow of water into the boiler tank Distiller will continue to operate until storage reservoir is filled with distilled water The reservoir float system turns Distiller off auto matically Distiller will not restart until sufficient water has been drawn from the reservoir NOTE To interrupt operation simply press Power switch to OFF position A 10 DISTILLER MAINTENANCE IMPORTANT To avoid personal injury unplug boiler tank cord only after Fan and Power switches fig G are turned off Distiller is unplugged from wall outlet and unit has com pletely cooled Boiler Tank Empty the water out of boiler tank after every 15 20 gal lons of water distilled or weekly whichever comes first To empty boiler press Fan and Power switches to OFF position Unplug main power cord from wall out let Unplug boiler tank cord Unscrew and remove black knob and raise lid Lift boiler tank up and off of lift spring bracket Lid stays attach
16. ing coil maintenance should be done by autho rized personnel only see Owner s Limited Warranty Reservoir To clean reservoir remove carbon filter cup and empty any water Clean with either hydrogen peroxide or a paste of baking soda and water Rinse thoroughly and steam sterilize page 9 The higher the room tempera ture the more often reservoir should be cleaned how ever the reservoir should be cleaned at least every six months NOTE If Remote Faucet Pump is installed disconnect tubing from reservoir elbow fitting before cleaning the reservoir Exterior Surfaces To maintain the exterior surfaces of Distiller wipe with a soft damp cloth The exterior stainless steel surfaces may be cleaned with stainless steel polish TROUBLESHOOTING 1 Distiller does not operate A Distiller is not plugged into properly rated voltage AC grounded electrical outlet or circuit breaker is tripped B Power switch is not on C Water connection is not open Boiler tank does not fill with water A Water connection is not open B Power switch is not on C Storage reservoir is full Draw sufficient water out of reservoir to activate float switch D Inlet water valve is defective E Water microswitch is defective Fan does not operate Fan switch is not on Boiler tank is not mounted on lift spring bracket Insufficient water in boiler to activate microswitch Fan switch is defective
17. n nut fig I Insert brass tube support into end of tubing Insert tubing into valve and hold firmly in place while threading nut onto saddle valve Tighten with a wrench Turn handle clockwise as far as possible The copper pipe is now pierced and valve is closed To open valve turn handle counterclockwise as far as possible Check for leaks Retighten compression nut if necessary Bolts RUSE SGN Whee eh ed A seca E Handle ssi Saddle Clamp Bracket A Installing Saddle Valve on Steel or PVC Pipe IMPORTANT DO NOT use a hot water supply Shut off main water supply and drain pipe Drill a 5 32 diameter hole in COLD water pipe Use a hand drill to avoid shock hazard Turn handle to expose piercing lance 3 16 beyond the sealing washer Assemble saddle valve on COLD water pipe so piercing lance fits into hole Tighten bolts evenly with saddle clamp brackets parallel DO NOT OVERTIGHTEN Slide compression nut over end of 1 4 tubing Place white compression ring on tubing Be sure wide end of ring is facing compression nut fig I Insert brass tube support into end of tub ing Insert tubing into valve and hold firmly in place while threading nut onto saddle valve Tighten with a wrench Turn handle clockwise to close valve Open main water supply To open valve turn handle counterclockwise as far as possible 10 Check for leaks Retighten compressi
18. ng coun terclockwise Raise lid and lift boiler tank up and off of lift spring bracket Lid stays attached to unit IMPORTANT DO NOT immerse boiler tank in water or other liquid 3 Using a sponge or cloth clean interior of boiler tank with hot soapy water Rinse thoroughly A FiGure F FIGURE G o Hinged mn Cover Black ek Knob Cord z Plug Receptacle Indicator Reinstall Boiler Tank CAUTION To avoid personal injury or property damage be certain Distiller is unplugged before installing boiler 1 Place hook of the boiler tank over the lift spring bracket located on front half of Distiller fig F 2 Be sure gasket on boiler is securely in place 3 Fit lid with attached tubes over gasket and onto boiler tank making sure threaded center support protrudes through hole in lid 4 Secure lid by turning black knob clockwise 5 IMPORTANT Make sure boiler tank moves down when pressing down on top of tank The tank should spring up when it is released fig G 6 Be sure to fully insert boiler tank cord plug into receptacle so the indicator line is NOT visible fig G A loose connection may damage tank cord and receptacle thus resulting in Distiller failure AU Sron AWM o Q gt Figure H Power ou 2 Fan Switch an Cord S Lift Switch Thermal Overload Spring Float Ball Reset Switch Bracket WATER SUPPLY CONNECTION
19. on nut if necessary Piercing Lance Sealing Washer Brass Tube Support White Compression Ring Compression Nut 1 4 Tubing B Y A To Distiller Cold Water Pipe Figure J Utility Faucet Connection optional For 3 4 male threaded faucet fig J Installation Turn off COLD water faucet Disconnect any appliance hose from faucet Insert rubber washer into brass body Screw brass body onto faucet Wood B amp O NH Screw valve into threaded hole on brass body Tighten with wrench 6 Slide compression nut over end of 1 4 tubing Place white compression ring on tubing Be sure wide end of ring is facing compression nut fig J Insert brass tube support into end of tubing Insert tubing into valve and hold firmly in place while threading nut onto valve Tighten with a wrench 7 Reconnect appliance hose to brass body A cap not included is needed if there are no hose reconnects 8 Turn on COLD water faucet 9 To open valve turn handle counterclockwise 10 Check for leaks Retighten compression nut if necessary NYZ Cold Water Supply D c Faucet Valve Rubber Washer pu y Brass Body piaeaneed gt White Compression Brass Tube Ring Unes Pe Support Compression Nut gt nge lt 1 4 Tubing Appliance HOSE seer rere Y To Distiller STEAM STERILIZATION Steam Sterilization f
20. or First Time Use NOTE Prior to first time use a steam steriliza tion procedure is recommended If Remote Faucet Pump System is installed disconnect tubing from reservoir elbow fitting before steam sterilizing Plug power cord into properly rated voltage AC grounded electric outlet Turn Power switch on Leave Fan switch in OFF postion You should hear water begin to fill the boiler tank When sufficient water fills the boiler tank heating element will turn on automatically After 15 20 minutes you should notice steam beginning to appear in the sight gauge CAUTION External surfaces will be HOT dur ing this process DO NOT TOUCH UNIT Continue steaming process for an additional 15 minutes Condensation on outside of reservoir is normal during this process Turn off Power switch and allow unit to cool completely When Distiller has cooled completely unplug power cord Install prepared carbon post filter cup into post filter holder in reservoir fig E USING THE DISTILLER Operational maintenance and replacement requirements are essential for this product to perform as advertised Before you start your Distiller be sure the water supply is open to the Distiller Lift the hinged boiler tank cover and check for pro per mounting of boiler by pressing down The tank should spring up when it is released fig G Be sure Fan and Power switch
21. r Cord A l Normal while steam sterilizing unit Thermal Overload Spring Float Ball Inadequate ventilation around Distiller Reset Switch Bracket Excessive dust on condenser coil vows Fan switch not on or fan motor defective Call your authorized distributor for service after problem has been corrected If raw water has entered reservoir clean and sterilize reservoir page 9 and change post filter page 6 11 WARRANTY REGISTRATION CARD Please fill out and return the enclosed registration card or register online at http www waterwise com customers customers asp Registration will not affect warranty coverage but may expedite processing of your warranty Registration is the only way to guarantee you will be notified by Waterwise of any issues that arise concerning this product OWNER S LIMITED WARRANTY Waterwise warrants to the original purchaser this product against defects in materials and workmanship excluding the disposable carbon filter and gasket for a period of two 2 years from the date of purchase on all electrical and non stainless steel components and fifteen 15 years from the date of purchase on all stainless steel parts Defects or failures due to shipping handling incorrect installation improper use or maintenance including abuse or neglect normal wear water conditions accidents alterations or modifications or unauthor ized repair are specifically excluded from this warranty
22. ting or cooling Wait at least one hour after a cycle is finished or interrupted before moving Distiller Boiling water or steam can cause severe burns DO NOT place near an edge of a surface where Distiller can be bumped or pulled down on some one DO NOT allow power cord or extension cord to hang over the edge of a counter or contact hot surfaces A short power supply cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord If an extension cord must be used its marked electrical rating should be at least as great as electrical rating of Distiller Electrical rating is found on louvered cover DO NOT touch hot surfaces Distiller gets very warm during use Allow to cool before cleaning To protect against fire electrical shock and injury to persons DO NOT immerse power cord or Distiller in water or liquid Plug Distiller into a properly rated voltage AC grounded electric outlet ONLY rated voltage label 10 13 14 16 located on louvered cover The cord has a three pronged plug which mates with a standard three pronged grounded outlet DO NOT cut or remove third prong from plug If an adapter is used be sure adapter wire and wall outlet are grounded If there is any doubt about the outlet being properly grounded check with a qualified electrician DO NOT operate with a damaged cord or plug after a malfunction or if Distiller has been dam aged in any manner Return to
23. with black plastic jam nut DO NOT OVERTIGHTEN Carbon Pre and PostTreatment Prefilter optional Carbon pretreatment consists of an in line filter housing and a two stage spun fiber and organic coconut shell carbon filter cartridge Pretreatment removes suspended particles to reduce maintenance and ensure more trouble free operation Carbon also improves the purity of the distilled water by significantly reducing substances such as benzene chlorine chloroform pesticides etc that are found in some tap water Cartridge should be replaced about once a year For installation instructions see Form 7812 included with the in line filter housing Post Filter optional An activated carbon post filter made from organic coconut shell enhances the taste and purity of the dis tilled water by significantly reducing possible carryover of substances such as benzene chlorine chloroform pesticides etc that may be present in some tap water Replace every 60 80 gallons distilled or every two months whichever comes first Sterilize and Rinse Carbon Filter Cup Before installing fully immerse new filter cup in distilled water for about five minutes Then sterilize filter cup by fully immersing in boiling water for about five minutes Allow filter to cool before handling Pour 1 to 2 cups of distilled water through filter cup to rinse away any small harmless carbon fines dust Water draining from the filter cup may contain black dust
Download Pdf Manuals
Related Search