software user manual
Contents
1. data communications If the user has entered some kind of working condition and then switch to other work page the system will prompt whether to stop the original working state then the user must switch the surface according to the purpose of the page just to look at another page or really want to enter other working condition to select yes or no Two radio module radio interoperability necessary conditions the same air baud rate channel frequency consistent Channel and frequency the frequency of the channel and read and set Each channel corresponds to a frequency that conventional products JZ86 series has eight channels JZ87 series has 16 channels Correspondence between the channel and frequency detailed product specifications Air speed air speed reading and setting Serial port parameters baud rate and parity of the read and set Serial port parameters must be set with the connected serial device or PC format consistent Radio ID When the user ID using the protocol JZ872 or JZ873 this ID number must be set and the different modules Radio ID number should be different Other products without setting a clear agreement Factory serial number it is the factory identification number identifies the product That product category factory years and serial number Users can only view Power save mode almost all products except JZ868 JZ878 JZ862 JZ864 outside can have power saving features The user to set a power saving f2. ea hy chose A Cancel 2 Select the wireless module radio is connected to the serial port baud rate and other parameters remain the default state then click Open button enter the main interface then select the product model and the fundamental frequency since the parameters of the wireless module to read and Model selection is required to write first and fundamental frequency RE Kodule Radio software y3 06 Msp Q Read W Radio Parameters Transmit Both Sides Tata transmit Please Choose Model Base Fre or Search FIRST Modell Base fre 3 Click the toolbar s Radio detection which started with software testing machine turn to a different baud rate and parity detection if successfully detected the module radio the status bar will be prompted to successfully detect the radio If successful the system will not detect the radio You should check the serial connection is connected the module radio is power whether the module is converted to RS232 or RS232 Again after the check click radio detection If the detection process to stop testing click the Stop test button to stop testing Description It is recommended for wireless module radio parameter settings before testing again Do not change the serial port test is successful properties full time and full parameter set 1 full time parameters First select the product model and the fundamental frequenc
3. the serial port parameters box Settings button set the prompt to set the status bar after the success of success VU field strength and power of reading 1 field strength reading Function of field strength limit of the function with some modules such as JZ87 series Connected modules click the field read button The module can read the current value of the field strength 2 power settings This function has a limit of some adjustable power module Connected modules the power input box enter a power value 0 255 and then click the Settings the system prompts the power to set success ESSI and Fower Rol CHEN Int Read Power trite Radio ID an pr ID Read H i Writel ie F the power to set the station ID and JZ875 1 read and set the station ID Station ID that wireless module ID which is an internal identification module the user can set and read Connected modules specified in the ID box enter the ID number such as 1 click the Settings the ID incurs included modules If you have set the ID of the module users can also be read out Connected modules click read button you can read the module ID Radio ID and O prar ID Read H wiritel Jaraa ole 300 poly Write 2 JZ875 and other power settings Certain types of modules Such as JZ875 there are two user selectable power 1W 2W In the power box select power such as 2W click the Settings button the system is p
4. the test if the user does not need to write the whole test open the read write parameters menu remove the read before the test selected ID protocol JZ872 or JZ873 only has full read and full set up operate only a single parameter is read and channel settings Help About the Software Exit Exit the software Operation of the main panel some specific operations in this column to achieve through specific buttons Parameters of the main page which wireless radio module read and set the radio parameters pass the test on the main page is to achieve two wireless module radio data transmission of each test Of course users can debug their software through any other serial port for data transmission Wireless module radio main parameters the channel and frequency air speed the serial port parameters of these three parameters In general the user can simply set these three parameters Other parameters are mainly targeted at users who need or modules the station ID for non ID protocol products JZ862 JZ863 JZ864 JZ865 JZ866 JZ868 JZ871 JZ878 for users without setting However an agreement to have the product ID ID protocol JZ872 JZ873 is ID number is their identity in order to determine their choice to receive data JZ875 JZ885 JZ230C power are borderline cases 1W and 2W no other modules Note The wireless module is a total of three modes of operation that is within three pages radio parameters on mass testing and
5. the test menu item selected Open the specified serial port it will choose the parameters separately and then click Write Parameters button the software parameters based on user write test before they decide whether radio stations detected and then the main parameters of the whole set After the success of the whole writing the status bar will be prompted to set up a successful whole Description full time and full set parameters for the main parameters the channel and frequency air speed serial port parameters baud rate and parity the parameters of single reading with a single set 1 channel and the frequency of reading First select the product model and the fundamental frequency see above section If the first detection of radio stations is not detected until the successful detection detection success is not no need to manually change the serial port properties for testing then click the channel frequency box read button channel and frequency after a successful read will be displayed Channel and Frequency Channel f1 Read il Write 2 Frequency t30 Z000MHZ 2 channel and frequency settings if the first detection of radio stations is not detected until the successful detection detection success is not no need to manually change the serial port properties for testing select the channel click the channel frequency box set button set the prompt to set the status bar after the success of suc
6. JIZHUO The wireless module settings and software communicated User s manual SHENZHEN JIZHUO TECHNOLOGY CO LTD TEL 86 755 83304518 83308451 81353151 FAX 86 755 83302824 Address NO 813 212BLD Tairan Tech Park Futian District Shenzhen China Post Code 518040 Email selina jizhuo com Website http www jizhuo com the system requirements Operating System Windows98 Windows Me Windows 2000 Windows 2003 Windows XP CPU Celeron 1 0G above Hard disk capacity 50M Memory 128M or more Graphics 1024 x 768 resolution Software Description Wireless module radio parameter settings the main interfaceas below An 2 RF Eodule Radio software 3 06 Doone Qer Ho Qrad A iritet Radio Parameters Transmit Both Sides Data transmit Please Choose Model Base Fre or Search FIRST Model Base fre Channel and Frequency Serial Humber Channel Read Write 2 2005 fog Frequency Read IT RF Baud Rate Band Ratel Read 3 Write 4 Fower Save Interval wake up from RF COM Farameters Wake up Mode forklime mms Sra et E d Ratel z 31 Ti i Ars bea 5 Write 6 Bes ithe Bi Verify a Read 0 Write atake from COM E ESSI and Power RSSI G ttnt Read IO Control for 872 873 with ID protocol Power foe Weite ID i Tl I Cd Radio ID and 875 885 2300 power Input m o 7 TD e
7. Read iH WriteL at D ae C Hf o poss 230 gaan i Hrid QutPut 7 il irite COM4 S600 HOHE S 1 Software interface from the menu bar toolbar status bar and operation of the main panel of which the main panel by a radio station operating parameters transmission testing data communication three pages Menu bar common operations can be achieved in these menus Toolbar common operations in the fast button in the way of this column can be quickly achieved Serial port enter the serial port settings window you can follow the appropriate format baud rate parity etc to open the specified serial port Radio detection the use of different baud rate in order to detect and check the radio testing is successful the status bar indicating success Stop testing users in the testing process can be stopped testing Read parameters read all the main parameters One time read channel and frequency air speed serial port parameters Default parameters will be conducted before full time radio detection if the user does not need full time testing open the read write parameters menu remove the read before the test selected ID protocol JZ872 or JZ873 only have full time only a single channel read operation parameters and settings Write Parameters The main parameters of the whole writing Write channel and frequency air speed serial port parameters Default parameters for all radio stations will be written before
8. cess 3 the rate of air to read If the radio is not detected until the first successful detection of radio detection detection success is not no need to manually change the serial port properties for testing then click the air speed box read button after a successful read rate of the air will be displayed EF Baud Rate Baud Rate 9600 Read Write 4 TAN ee en arr 4 air speed settings If the radio is not detected until the first successful detection of radio detection detection success is not no need to manually change the serial port properties for testing after choosing the air speed and then click the air soeed box settings button set the prompt to set the status bar after the success of success 5 to read the serial port parameters If the first detection of radio stations is not detected until the successful detection detection success is not no need to manually change the serial port properties for testing then click the serial port parameters box read button serial port baud rate and parity will be displayed after a successful read COM Farameters Baud Rate 3600 inal ai oy er Read 5 Wri te 6 ify rs SAO te 6 Set the serial port parameters If the first detection of radio stations is not detected until the successful detection detection success is not no need to manually change the serial port properties for testing select the serial port baud rate and parity after good and then click
9. eatures of products it should be declared in the order Failing such statement the factory power saving features without opening the product JZ863 JZ871 all have hardware serial wake up wake up and power saving mode JZ872 JZ873 has a hardware wake wake up the serial port and air wake Here the user can change the power save mode Products with power saving feature the default is hardware wake up mode unless the user specified when ordering factory saving mode IO switch ID protocol JZ872 JZ873 with the IO switch control functions Here is to switch the remote control and read the presentation Switch the control center computer this side of the table must be transparent protocol products sub station ID protocol products JZ872 or JZ873 On mass testing testing two wireless module radio data transmission Two computers serial port or two serial ports of a computer are connected to the wireless module radio the software were set to open choose one main income click accept to enter the receive mode choose one main issue Enter the sender needs to send the master and then click Send The two sides can achieve data to each other a Operations Guide the radio detection 1 first open the serial port From the main screen click the toolbar serial button enter the serial port settings window CON Option COM Port com Baud Rate 9g00 o Verify NOHE Data Bits j Begin Biti Stop Bits oe
10. mmended from time to time sent if sent back after the other one did not receive the data it sent back data that will not cause interruption of transmission time to time to send the data needed and the size of with rate conditions Sn RF Nodule Radio software 3 06 COM Option Search Radio Read or Write Help T come Search S Qf Step QRead 4 Radio Farameters Transmit Both Sides Data transmit jj fest Type P send stop TORE Sand M appoint Data If transmit a AE EEO EB ath are j if TH after RE THRE Mode Character types Tyo Timing i 3 Mainlii Matnni ASCII HEX Clear Pa i Time tl ms Transmit 3 Set the primary sender Select the other main sender the sender in the main software to pass the test page select the main issue option and then send the text box to send the contents of a single click send button ammonium two modules that is entered on the pass state One received after the data back to the other data Note the user to pass the test state if the switch to the Radio parameters or data communications page the system will prompt whether to stop to pass the test state users may need to select Yes or No As shown below Farning 4 pass the test results Test results on the transfer test in real time or in the Statistics box is displayed including the transmission reception number the number of errors the success rate and so on Etat o we E Error duces OO I
11. ote protocol JZ872 or JZ873 ID ID number and then select the appropriate output or output2 switch state and click the Settings button the system is set to issue remote commands to change the remote switch modules corresponding output state to read the factory serial number 1 In general each module at the factory are recorded in January and the factory serial number Connected modules click read button the factory serial number that is read out and displayed JL the transfer test 1 The serial port settings two radio module two radio stations were connected to a computer serial port or two serial ports open the Serial Settings window according to the wireless module radio baud rate and parity for the serial port parameters open connect to a wireless module radio serial do not know if the wireless module radio serial port parameters first detected radio or read its parameters two software modules respectively here radio radio serial port parameter to open is good 2 set the main debit Selecting based debit side the main recipient s software in the oass the test of page select the main income option then click accept button ammonium state into the main collection in the Send option to send or choose to return time after the send send the return to the main sender receives the data after postback data sent according to a specified time interval to send data Can be selected if the test is reco
12. rompted to set success 7X read and set the power saving mode 1 to read and set the power saving mode Some modules have power saving features sleep function hardware wake up wake up the serial port wake up air Generally recommended hardware wake up mode Select the appropriate power saving mode and then click the Settings the system prompts to set success If the user does not Know which module is currently used in power saving mode click the read button Power Save i Interval wake up from RFI Wake up Mode WorkTime ns 3 et 7 SleepTime S14 Read iC Write D aflake from com 2 Serial wake When the module s power saving mode for the serial port wake up you can use this feature Click the serial wake up dormant module that wake t lO switch remote reading and control This feature is only with the agreement JZ872 873 valid ID When you first connect a transparent protocol JZ872 or JZ873 modules while at the other end connected to the JZ872 with ID protocol or JZ873 1 Remote switch input read First the target ID in the input box with the remote protocol JZ872 or JZ873 ID ID number then click read button you can read the remote JZ872 or JZ873 digital input status IO Control for 872 673 with ID protocol ID Ii C t Input Read I ao 86 oe OutPut trite OK Write M 2 switch output settings First the target ID in the input box with a rem
13. v Rectify data communication 1 Switch to the data communications page this time in another state if the system will be prompted to enter the data communication status select Yes that enter the data communication status at this time into the receiving state check box check mark a Will you stop Transmitting both sides Lae J 2 and then send the data type options according to their need to select ASCII ASCII characters and HEX hexadecimal Then send the input box need to transfer data click Send button the data that is sent through the module 3 If the data sent back to the other side sent back data that is displayed in the receiver Radio Parameters Transmit Both Sides Data transmit EX PBs j Send f ASCII HEX f ASCII HEX V Change into Data trasmitting Status Tx Transmit Both Sides Data have been sent ok
14. y see above section Read before all the default parameters will be automatically radio testing testing all the parameters after a successful read If the user has successfully detected the radio read the whole can be removed before the test by opening the read write parameters menu remove the read before the test menu item selected Open the specified serial port click read parameter button the software read the parameters based on user testing before they decide whether the radio station testing and then read all the main parameters Read successfully the wireless module radio main parameters are displayed in the corresponding list box or text box Success will be prompted to read the status bar Sa RF Nodule Radio software 3 06 COM Option Search Radio FAGES eee Help T con I i aaa Bui Ej trite All Parameters fy etter Lives EE iy Search Before Read Write Please Choose Model Base Fre or Search FIRST Hodel Channel and Frequency Channel a irite afl Frequency CRF Baud Rate Pand Rate ttt Re a mew 2 all parameters set First select the product model and the fundamental frequency see above section Set before all the default parameters will be automatically radio testing testing all the parameters after a successful set If the user has successfully detected the radio the whole set can be removed before the test by opening the read write parameters menu remove the read before
Download Pdf Manuals
Related Search