User Manual
Contents
1. Example 4 To erase the stored set of weight range in memory location 0 1 2 Press MR key Press 0 key and then press CE key twice The stored set of weight range is erased To display current weights for LOW SET or HIGH range Press 1 LOW key to show minimum low range 99 5 Press 1 LOW key again to show maximum low range 100 0 Press 2 SET key to show minimum set range 101 5 Press 2 SET key again to show maximum set range 102 0 Press 3 HIGH key to show minimum high range 103 0 Press 3 HIGH key again to show maximum high range F2 COUNT Count function allows scale to count items from the scale s platform This is important to count items like coins or nails or other things of almost identical type in terms of weight shape and size First make a sampling of the items for counting After the scale calculates weight from the samples items can be added on the platform and the scale will start counting them The current count value can be saved to a specific memory location or can be added to or subtracted from a value stored in a specific memory location To activate counting make a sampling of your items by doing the following 1 2 3 Press SET key Enter the number of items for sampling minimum of 5 items Then press SET key Put the items on the scale s platform The display starts to blink while the weight on the scale is not yet stable Once the weight becomes stable the display stops blinking2. Shuts down after 5 min of non use in battery programmable auto off duration Visit http Awww elane net exceedpc exceedi exceedi htm for the more details PREPARING THE SCALE FOR USE i Fit the weighing platform to the body of the scale via the location points making sure that the platform opens toward the front keyboard end of the scale Refer to the diagram below SEMI OVAL CUT OUT TO THE FRONT WEIGHING PLATFORM OPEN THE HINGED FLAT TO WEIGH LARGE ENVELOP VERTICALLY Fitting the Weighing Platform to the Scale ii Plug the mains adapter supplied with the scale into the mains and connect the adapter s output plug to the input socket at the rear of the scale iii Place the scale on a firm level surface switch on the mains supply and press on the scale the ON OFF key iv The display shows 0 0 gm zero grams and the scale is now ready to use OPERATING THE EXCEED SCALE The Exceed i Scale offers a straight forward keyboard layout and corresponding display on the scale Weight display is available in six 6 units of weight and can be set by pressing the key of the desired unit It has six 6 basic functions labeled with F1 F6 on the keyboard which can be used immediately The other ten 10 programmable functions require the use of Exceed i PC Program to activate and use each function There are also keys that allow users to enable scale features like backlight on or off or set values like set
3. LOW When in Batch function it toggles display of minimum and maximum low range SET When in Batch function it toggles display of minimum and maximum set or exact range HIGH When in Batch function it toggles display of minimum and maximum high range SET FROM DISPLAY This is used when function requires input of values and the value that to input is same as the weight display example input of target weight or count 0 DURATION INTERVAL CLR DISPLAY When in Data Log function it toggles display of time duration or time interval of current data logging Time duration display tells how long the data log has been going on while time interval display tells the current time interval of data log This key is also used to clear displays of current weight range for low set and high in batch weighing and count displays during memory recall MR CE ESC This is used to exit from the 6 basic functions and go back to normal weighing mode of the scale It also acts as a backspace clear previous input when entering required values When in MR key and after input of memory location pressing this key twice will erase the contents of the selected memory location It is also used to stop or disable data logging DATA SEND This is used to manually send weight data to a computer program or device if designed and programmed to communicate with the scale SEND FORMAT This is used to set format of weight data sending to a computer program or to a devi
4. a time interval of 10 seconds gt 76 days 9 hours and 20 minutes within a time interval of 100 seconds gt 2years 33 days 21 hours and 20 minutes within a time interval of 1000 seconds Data logged on the external memory cartridge can be retrieved and further use for analysis or data export The Exceed i PC Program can be used to read the external memory cartridge and save the data in itas a TEXT file or as a CSV comma separated values file To use data logging on the Exceed i scale make sure that this function is already unlocked in the Exceed i PC Program Upon purchase of the external memory cartridge user will receive an unlock code that can be used to enable the function After this data logging can be started by doing the following 1 Press DATA LOG key 2 Enter the time interval of data logging 0 1 1000 seconds The decimal point is displayed and will be adjusted accordingly Press SET key to confirm entry 3 Data log starts and records current weight on the scale s platform within the time interval specified An arrow is lighted on the display every time interval 4 To pause data logging press DATA LOG key P is lighted on the lower right corner of the scale 5 To resume data logging press DATA LOG key again P display is cleared and data logging resumes 6 To view the current data log duration how long data log has been going on press 0 key The display toggles with data log interval 7 To permanently stop data l
5. and scale freezes for 5 seconds while it calculates unit weight of the items If display is cleared items can now be added to the platform and the scale will start counting them 5 The count of items displayed can be saved in a specific memory location or can be added to or subtracted from a value stored in a specific memory location Example 1 To activate counting and make a sampling for 15 items Sipe F2 Press SET key 00015 F2 Press 0 0 0 1 5 keys The press SET key to confirm entry 0 0 Aly 15 F2 Put the 15 items on the platform Wait for the A to blink and display steadily 100 0 15 F2 After the A display is cleared user may start adding items for counting 100 0 To save the current count to a specific memory location do the following 1 2 Press MS key A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where current count will be saved and this can be used to retrieve the value for later use Previous value stored in this memory location will be overwritten Press SET key to confirm entry and save the current count or CE key to cancel this operation the current count will not be saved Example 2 To save the current count value to memory location 0 do the following 1 2 Press MS key Press 0 key then SET key The current count value is now saved in the selected memory location To add th
6. code for a certain function visit www elane net exceedpc exceedi unlockcode htm The following summarizes these 10 programmable functions P1 WEIGHT DATA This programmable function displays current weight from the scale s platform Scale must be in normal weighing mode or in DIFF WEIGHT mode when using this function P2 BATCH DATA This programmable function displays current weight from the scale s platform and the result of batch weighing LOW SET or HIGH Scale must be in BATCH mode when using this function P3 COUNT DATA This programmable function displays current count of items on the scale s platform Scale must be in COUNT or DIFF COUNT mode when using this function P4 FACTOR DATA This programmable function displays factored weight reading Scale must be in FACTOR DATA mode when using this function P5 DATA LOG This programmable function allows user to read logged data from the external memory cartridge of the Exceed i Scale The external memory cartridge of the scale is an optional component and this can be used to store or save weight values during data logging Please refer to Data Logging section of this manual to know more about this function P6 COIN COUNTER This programmable function allows the scale to be connected to a coin counter application program which is a part of the Exceed i PC Program The coin counter application program allows user to count coins and display the total monetary value of these coins Avai
7. ELANE Exceed i 5kg 0 5g Intelligent Precision Electronic Scale Max 5000g d 0 5g USER MANUAL CONTENTS INTRODUCTION Specifications Preparing the Scale for Use Keyboard Layout Operating the Exceed Weighing Scale KEYBOARD FUNCTIONS BASIC FUNCTIONS PROGRAMMABLE FUNCTIONS SOFTWARE UPDATES INTRODUCTION The Exceed i Intelligent Precision Electronic Scale is a state of the art weighing instrument which encompasses intelligent features of a weighing scale that anyone can think of It is not only a simple weighing scale but it can do batch weighing item counting and other important weight calculations The Exceed i Intelligent Precision Electronic Scale is also equipped with ten 10 optional programmable functions which cannot be found on any other scales These functions maximize scale use and allow scale users to benefit the most out of their Exceed i scale The succeeding sections give more details on these features and functions of the Exceed i scale Specifications Capacity 5000g Graduation Resolution 0 5g step Min startup weight detection 1 5g Accuracy 0 1 of reading 1 digit Power consumption Approx 0 40 watts Tare Unlimited up to scale s maximum capacity Weight of Scale 1100g Dimensions 20cm X 24 5cm X 7cm Display Liquid crystal display with back light Platform Size Fold up 19 cm x 12 cm platform Power Supply Mains via 12 Volts Main Adapter or 6 AA batteries not supplied Auto off
8. Press DATA SEND key to start sending data every time interval To stop sending data to the program press DATA SEND key again 3 To switch to manual sending format press SEND FORMAT key No input value is required for this function Press DATA SEND key to manually send data to the program EXCEED i PC PROGRAM This is the application program that comes with the Exceed i Scale It is a multi function and integrated software that allows user to gt Update scale with its latest software that includes software enhancements FREE of charge gt Unlock the other 10 optional programmable functions so that they can be used gt Interact users computer with the scale using the other application programs that are packaged with it like postal calculator and coin counter gt Read data saved on the external cartridge optional scale component after data logging User can get this application program for FREE Register Exceed i Scale on the web To do this visit www elane net exceedpc exceedi registration htm Download and install it in your computer NOW Download this from www elaneinternational com Exceedi NewExceedi_PCProgram msi PROGRAMMABLE FUNCTIONS The Exceed i Scale is equipped with ten 10 optional programmable functions These are more powerful versatile and complicated functions of the scale To use a certain function user needs to purchase an unlock code Use this to enable that function on the Exceed i Scale To purchase unlock
9. ce It can be set to manual or automatic sending of data Refer to succeeding section on how to send data to a computer program and how to format data sending SCALE SETTING FUNCTIONS These functions are related to settings of the scale Settings are saved and will still take effect the next time the scale is turned on GRAM This function changes the weight display to gram units LB OZ This function changes the weight display to lb oz pounds and ounces units TROY LB OZ This function changes the weight display to troy Ib oz troy pounds and ounces units KG This function changes the weight display to kilogram units LB This function changes the weight display to lb pounds units TROY LB This function changes the weight display to troy Ib troy pounds units ZERO TRACKING ON OFF f This function turns on or off zero tracking feature of the Exceed I Scale Refer to later section on the explanation of zero tracking function BACKLIGHT ON OFF This function turns on or off scale back lighting KEY BEEP ON OFF at This function turns on or off key beep of the scale AUTO OFF DURATION This function sets the auto off duration of the scale when it is in battery mode Input is in h mm ss 0 00 00 format The default auto off duration is 3 minutes ON OFF This will turn on or off the scale USER CALIBRATION OF THE EXCEED SCALE In case the scale loses its accuracy due to dropping or putting heavy objects which are b
10. e current count to the value stored in a specific memory location do the following 1 2 Press M key A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where current count will be added and where the result of the addition will be saved Previous value stored in this memory location will be overwritten Press SET key to confirm entry and save the result or CE key to cancel this operation the current count will not be added to the count value stored in selected memory location Example 3 To add the current count value to memory location 0 do the following 1 2 Press M key Press 0 key then SET key The current count value is now added and saved in the selected memory location Example If current count value is 15 and memory location 0 contains count value of 15 the result would be 30 which will be saved in memory location 0 To subtract the current count from the value stored in a specific memory location do the following 1 Press M key 2 A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where current count will be subtracted from and where the result of the subtraction will be saved Previous value stored in this memory location will be overwritten Press SET key to confirm entry and save the result or CE key to cance
11. eyond the scale s limit user calibration can be done on the scale A 2 kg weight is needed for the calibration To perform user calibration of the scale 1 Press USER CAL key Remove any weight on the scale s platform 2 Display becomes CAL 0 3 Wait for the display to become CAL 1 and then place the 2 kg weight on the scale s platform Scale will start calibrating 4 When the display on the upper part of the LCD is cleared this signals that calibration is finished and was successful The scale can be used again Note In cases where you cannot calibrate the scale using user calibration remote scale calibration maybe required to fix the scale This is one of the 10 programmable functions of the Exceed Scale and can only be used after unlocking it USING COMPUTER PROGRAM TO CONNECT TO SCALE The Exceed i Scale is also designed to send and received data from other serial devices like computers Download and install the sample program that demonstrates this function To send data to the computer program 1 Run the sample program Press DATA SEND key to send data to this program sent data is displayed accordingly 2 Default format to send data is manual sending This sends data only once after pressing DATA SEND key To change the format to automatic sending data will be sent every time interval specified press SEND FORMAT key and enter the time interval for automatic data sending Press SET key to confirm entry
12. f items can now be done results will be indicated on the LCD or this set of weight range can be saved for later use VVVVVV Example 1 To program the following weights for low set and high range Low Range 98 5 99 5 grams Set Range 100 0 101 5 grams High a 102 0 103 0 grams Press SET key The decimal point is displayed and will be adjusted accordingly Press 0 0 9 8 5 for minimum low range then press SET key Press 0 0 9 9 5 for maximum low range then press SET key Press 0 1 0 0 0 for minimum set range then press SET key Press 0 1 0 1 5 for maximum set range then press SET key Press 0 1 0 2 0 for minimum high range then press SET key Press 0 1 0 3 0 for maximum high range then press SET key Place the item for batch weighing on the scale s platform Results will be shown on the scale s LCD ONOORWN In cases where there is only one value for each range of low set or high example low range 99 0 grams set range 100 0 grams high range 101 0 grams the same value must be entered in the minimum and maximum range To save the current set of weight range entered do the following 1 Press MS key 2 A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where that set of weight range will be saved and use this to retrieve the range and use it for batch weighing again Previous set of weight range stored in this
13. grams do the following me genes 4 Press SET key The decimal point is displayed and will be adjusted accordingly 0015 0 F4 Press 0 0 1 5 0 keys 12 5 85 33 F4 The press SET key to confirm entry The calculated percentage will be shown on 12 the upper part of the LCD F5 DIFF COUNT Diff Count function allows scale to count the number of items that are being removed from or being added to the scale shows the change in count of the items on the platform It displays both the current count of items on the platform and the count of items being removed or being added This is important to know the number of items that are being removed or added on the scale Count function must be prior to Diff Count function To count items that are being removed or being added to the scale do the following 1 After counting process see F2 Count function above press DIFF COUNT key 2 Start removing or adding items on the scale s platform The default time out is 3 seconds to get stable weight from the platform This means that after removing items the scale waits for 3 seconds of no weight change and interprets this as change in count of items 3 Scale displays the current count on the lower portion of the LCD and the change in count on the upper portion of the LCD A negative sign on the upper LCD indicates that items are being removed from the platform If there is no negative sign display it indicates that items are being added to the platf
14. in the selected memory location To retrieve a weight factor stored in a specific memory location do the following 1 Press MR key 2 A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number you entered refers to the memory location where that set weight factor was saved 3 Press SET key to confirm entry and retrieve the weight factor from that memory location Weight reading is calculated according to this weight factor and will be displayed on the scale Example 3 To retrieve weight factor saved in memory location 0 1 Press MR key 2 Press 0 key and then SET key The stored weight factor is retrieved and is used to compute weight reading F4 WEIGHT Weight function calculates the percentage of the current weight on the platform with regards to an entered target weight This percentage is calculated and displayed as the weight on the scale s platform changes This is important to determine the proportion of the weight on your scale with regards to your predefined target weight To calculate percentage of current and target weight do the following 1 Press SET key 2 Enter the target weight to calculate the percentage against the current weight 3 Press SET key to confirm entry The percentage which is equal to current weight target weight X 100 is shown on the upper part of the LCD Example 1 To calculate percentage of current 12 5 grams and target weight 15 0
15. l this operation the current count will not be subtracted from the count value stored in selected memory location Example 4 To subtract the current count value from memory location 0 do the following 1 Press M key 2 Press 0 key then SET key The current count value is now subtracted and saved in the selected memory location Example 1 If current count value is 15 and memory location 0 contains count value of 30 the result would be 15 which will be saved in memory location 0 Example 2 If current count value is 15 and memory location 0 contains count value of 10 the result would be 5 which will be saved in memory location 0 To display the count value stored in a specific memory location do the following 1 Press MR key 2 A cursor on the lower right of the scale s LCD will blink and then press a number from 0 to 9 where to retrieve the stored count value 3 Press SET key to confirm entry and display the stored count value Example 5 To display the count value stored in memory location 0 do the following 1 Press MR key 2 Press 0 key then SET key The count value is stored in the selected memory location will be displayed F3 WEIGHT FACTOR Weight Factor function allows scale to multiply the current weight reading by a certain factor This is important to increase or decrease weight reading by a given factor Weight factor can be from 0 001 up to 2 000 After input of valid weight factor the calculated weight reading
16. lable coin counters are for Australia UK USA Canada and Europe coins contact us if you want a customized coin counter for other countries Each of these coin counter programs must be unlocked first before they can be used in the Exceed i PC Program P7 POSTAL CALCULATOR This programmable function allows the scale to be connected to a postal calculator program which is a part of the Exceed i PC Program The postal calculator program calculates postal fees of different postal services for different countries It can be connected to the Exceed ij scale to calculate the actual postal fee of the item on the platform or manually input the weight of your item Available postal calculators are for Australia UK and USA contact us if you want a customized postal calculator for other countries Each of these postal calculator programs must be unlocked first before they can be used in the Exceed PC Program P8 REMOTE CALIBRATION This programmable function allows user to perform remote scale calibration of his Exceed i scale In cases where there is need to adjust scale s calibration due to change in demographic location or abnormalities of the surroundings use this to adjust calibration settings of the scale P9 REMOTE SCALE This programmable function allows the scale to be connected to an external weighing platform Exceed i scale can have an external weighing platform with separate load cell and it usually can accommodate heavier weights up
17. memory location will be overwritten 3 Press SET key to confirm entry and save the current set of weight range or CE key to cancel this operation no set of weight range will be saved Example 2 To save the current set of weight range that was just entered in memory location 0 1 Press MS key 2 Press 0 key and then SET key The current set of weight range is now saved in memory location 0 To retrieve a set of weight range to be used for batch weighing do the following 1 Press MR key 2 3 A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where that set of weight range was saved Press SET key to confirm entry and retrieve the set of weight range for batch weighing Example 3 To retrieve the stored set of weight range from memory location 0 1 2 Press MR key Press 0 key and then SET key The stored set of weight range is retrieved and can now be used for batch weighing To erase a set of weight range stored in a specific memory location do the following 1 2 Press MR key A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number entered refers to the memory location where the set of weight for erasing is saved Press CE key twice and the memory location display will be cleared The set of weight range stored in the selected memory location is now erased
18. ogging press CE key Data logging cannot be resumed in this case 8 Data logged can now be converted to TEXT or CSV file using Exceed PC Program Warning Starting another data log session will erase previously recorded data in the external memory cartridge Make sure that current data on the cartridge are exported to TEXT or CSV files first before starting another data log Example To start data logging using a time interval of 0 1 seconds Press DATA LOG key Press 0 0 0 0 1 keys in succession The decimal point is shown and is adjusted accordingly Press SET key to confirm entry Scale starts recording weight values to the external memory cartridge within the specified time interval 5 Use Exceed i PC Program to read recorded weights from the external memory cartridge SCALE SOFTWARE UPDATES EON If there are software enhancements for Exceed i Scale it is very easy to update it with the latest The Exceed i PC Program also includes a tool to update the software of the Exceed i Scale via Internet To update Exceed i Scale with its latest software please do the following 1 Download and install Exceed i Scale PC Program refer to previous section on how to download and install this application program Close all other opened applications or windows 2 Run Exceed I Scale PC Program From the options click Update Software button Make sure that Exceed i Scale is registered first to proceed with the free software update refer to p
19. orm Example 1 To count items that are being removed from or being added to the scale after counting process in Example 1 of Count function do the following 1 Count items on the platform first Refer to Example 1 of Count function Press DIFF COUNT key 2 Remove 3 items from the platform Scale shows 3 on the upper part of LCD while 12 on the lower part of the display The upper display goes back to 0 after 3 seconds of stable weight 3 Put back the 3 items that you removed Scale now shows 3 on the upper part of LCD while 15 on the lower part of the display The upper display goes back to O after 3 seconds of stable weight F6 DIFF WEIGHT Diff Weight function allows scale to calculate and show the weight that is being removed from or being added to the scale shows the change in weight of the items on the platform It displays both the current weight of items on the platform and the weight of items being removed or being added This is important if you need to know the weight of items that you are removing or adding on the scale To show the weight of items being removed from or being added to the scale do the following 1 Start removing or adding items on the scale s platform The default time out is 3 seconds to get stable weight from the platform This means that after removing items the scale waits for 3 seconds of no weight change and interprets this as change in count of items 2 Scale displays the current count on the lowe
20. r portion of the LCD and the change in count on the upper portion of the LCD A negative sign on the upper LCD indicates that items are being removed from the platform Example 1 To count items that are being removed or being added to the scale after counting process in Example 1 of Count function do the following 1 Count items on the platform first Refer to Example 1 of Count function Press DIFF COUNT key 2 Remove 3 items from the platform Scale shows 3 on the upper part of LCD while 12 on the lower part of the display The upper display goes back to 0 after 3 seconds of stable weight 3 Put back the 3 items that you removed Scale now shows 3 on the upper part of LCD while 15 on the lower part of the display The upper display goes back to O after 3 seconds of stable weight MISCELLANEOUS FUNCTIONS These functions are related to data format input and display on the scale TARE This is used to tare the current weight on the scale weight is set to 0 This is helpful when there is need to weigh items that must be placed in a container First put the container in the platform press TARE key and put the items on the container The weight shown on the scale is the weight of the item only USER CAL This is used to perform user calibration of your scale In cases where the scale loses its accuracy due to dropping or putting items that are too heavy for the scale recalibration is required Refer to later section on how to perform
21. revious section on where to register Exceed i Scale 3 Exceed i Scale PC Program will download a file and after this proceed now with the software update Wait for the entire update process to finish After this a confirmation will appear that your Exceed Scale s software was successfully updated If there are errors during the update Exceed i Scale PC Program will tell it so For further help regarding Exceed i Scale please visit http www elane net exceedpc exceedi FAQ htm If there are problems with the software update please send email to information elane net
22. ter than or equal to minimum LOW low range AND less than or equal to maximum low range The current weight on the scale is within SET or EXACT range greater than or equal to minimum set range AND less than or equal to maximum set range vy SET The current weight on the scale is within HIGH range greater than or equal to minimum PA high range AND less than or equal to maximum high range If there is no arrow pointing to LOW SET or HIGH on the scale s LCD the weight on the scale is not within the range of low set or high range To program a set of weight range do the following 1 Press SET key 2 Enter weight for the following confirm each entry by pressing SET key Minimum Low Range this is the lowest weight classified in the low range Maximum Low Range this is the highest weight classified in the low range Minimum Set Range this is the lowest weight classified in the set or exact range Maximum Set Range this is the highest weight classified in the set or exact range Minimum High Range this is the lowest weight classified in the high range Maximum High Range this is the highest weight classified in the high range 3 If the weight entered is not valid for the range Error will be displayed and requires another input value for that range again To cancel the entire operation press CE key no values for batch weighing will be programmed 4 After completing entries for each range batch weighing o
23. ting of auto off duration The display and prompts on the scale will guide them on how to use these features and functions DISPLAY LAYOUT Receive Data Sart e tener Input and Output aeit Display Battery Low smoor _ Function Symbol Display Date t Hanna af 8 gi Usage Display Tare smeo E _ 4 Memory Location Display 988 Batch Weighing Symbols Display Hold Symbol Count Process Symbol A bor v Yv Y Y K v E v Weight Display Count Display for Diff Count Function Output amp Function Symbols KEYBOARD LAYOUT ELANE e Exceed 7 BOB d amp p GEE OO a CEE NAI 7 a WEIGHT BACSLIGHT ag AUTO 7 Oa CIF DIRATA LIW EET H4 1 2 3 EET FEDH DURATE SET a CEESC ow sar Pece wie ote wey freed DISPLAY CENA Lay maodkg d 0 4g wat BASIC FUNCTIONS The following section gives details on the 6 basic functions of Exceed i Press the corresponding key to activate a function except for DIFF COUNT function which can only be activated after COUNT function F1 BATCH Batch function allows scale to batch weigh items This is important when there is a need to pack items according to a programmed standard set of weight range It indicates whether the item they are packing is below the standard weight within the standard weight or above the standard weight The result of batch weighing is indicated by the following display y The current weight on the scale is within LOW range grea
24. to 30 kg P10 USER PROGRAM This programmable function is intended for a customized application program that users may want for their Exceed I scale DATA LOGGING FUNCTION Data logging function is one of the programmable functions of the Exceed ij Scale This feature allows user to log or record current weight on the scale s platform Weight data will be saved in the external memory cartridge attached to the scale This is an optional component of the scale and available only upon purchase of the cartridge This feature needs to be unlocked in the Exceed i PC Program Data logging is important when there is a need to monitor and record the weight of an object for some time within a given time interval It can also be used for scientific experiments that require recording of weight within a precise time The data logging feature can record weights within a minimum time interval of 0 1 second to a maximum of 1000 0 seconds This assures that even a weight change of the object within 0 1 second will be recorded It also has a PAUSE function that allows pausing of data logging and resuming it afterwards The external memory cartridge has a maximum size of 128 KB which can be used to record approximately 65 500 max weight data This is enough to record weight data for approx gt 1 hour and 50 minutes within a time interval of 0 1 second or gt 18hours and 11 minutes within a time interval of 1 second gt 7 days 15 hours and 19 minutes within
25. user calibration of the Exceed Scale DISPLAY HOLD This is used to freeze the current weight display on the scale After 5 seconds of no weight change weight becomes stable it locks the display for 20 seconds This is helpful when there is need to weigh items that are too big and blocks the scale s display MR Memory Recall This is used in functions where data can be saved or stored in memory like Batch and Count functions It is used to retrieve data saved in a given memory location 0 to 9 It is also used to erase data currently stored in a selected memory location 0 to 9 Refer to previous sections on how to perform these processes MS Memory Store This is used in functions where data can be saved or stored in memory like Batch and Count functions It is used to save data in a selected memory location 0 to 9 Refer to previous sections on how to perform this process M Memory Add This is used in functions where data can be saved or stored in memory like Batch and Count functions It is used to add current count value to the stored value in a selected memory location 0 to 9 Refer to previous sections on how to perform this process M Memory Minus This is used in functions where data can be saved or stored in memory like Batch and Count functions It is used to subtract current count value from the stored value in a selected memory location 0 to 9 Refer to previous sections on how to perform this process
26. will be displayed The current weight factor entered can also be saved to a specific memory location for later reference To change the current weight reading by a certain factor do the following 1 Press SET key 2 Enter the weight factor to multiply with the current weight 3 Press SET key to confirm entry The current weight multiplied by the factor provided will be shown in the weight display Example 1 To change the current weight reading by a factor of 1 200 do the following Press SET key The decimal point is displayed and will be adjusted accordingly 12 5 1 200 F Press 1 2 0 0 keys The press SET key to confirm entry The calculated value 15 0 will be shown on the weight display current weight x weight factor To save the current weight factor to a specific memory location do the following 1 Press MS key 2 A cursor on the lower right of the scale s LCD will blink and a number from 0 to 9 can be pressed The number you entered refers to the memory location where current weight factor will be saved and you can use this to retrieve the value for later use Previous value stored in this memory location will be overwritten 3 Press SET key to confirm entry and save the weight factor or CE key to cancel this operation weight factor will not be saved Example 2 To save the current weight factor to memory location 0 do the following 1 Press MS key 2 Press 0 key then SET key The current weight factor is now saved
Download Pdf Manuals
Related Search