AG188N-USER MANUAL-W-V080408-En 1218KB
Contents
1. Configure PPPoE Enable PPPoE PPPoE server Enter ANY if no specified from your ITSP Enter PPPoE username and pin in the username and password AG 188N will automatically obtain WAN port network information from your ITSP if PPPoE setting and the setup are correct Notice If user accesses the gateway through WAN port He should use the new IP address to access the gateway when the WAN port address was changed 10 42 AG 188 User Manual 2 3 2 LAN Config lt lt VoIP Gateway ATCOM Current State LAN Configuration Network LAN Config C Bridge Mode VoIP Advance Ip 192 168 10 1 255 255 255 0 Dial P DHCP Service NAT Config Manage If you are using lan please reconnect with new IP after your modification Update System Manage Bridge Mode Enable this option to switch to bridge mode Gateway won t assign IP for its LAN port in bridge mode and its LAN and WAN port will be in the same network This setting won t take effect unless you save the config and reboot the device IP Netmask Set the IP and Netmask for the LAN DHCP Server Enable DHCP service in LAN port NAT Enable NAT 2 4 VoIP 2 4 1 SIP Config M VoIP Gateway ATCOM Current State SIP Registered Configuration Network Tes CM T posee 0 ly IAX2 Config System Manage Setting page of public SIP server Register Server Addr Register Server Port Regist2. 2 9 1 Account Manage VoIP Gateway Current State Account Configuration Network dmn Re 2208 Dial Peer Config Manage Update admin 4 System Manage Config Time Config Loaout amp Reboot Set web access account or keypad password of AT 530 2 9 2 Syslog Config S VoIP Gateway MGR Log Level Dial Peer SIP Log Level None M Config Manage 14X2 Log Level None wj Current State Syslog Configuration Network VoIP System Manage Account Management Apply speeraswhdeansaustooeasatesntsoes alk Sysiog Contig Apply Time Config Logout amp Reboot Server IP set the syslog server address Server Port set the syslog server port MGR Log Level set the MGH log level SIP Log Level set the SIP log level IAX2 Log Level set the log level Please click apply after setting 28 42 AG 188 User Manual 2 9 3 Time Set Current State Network VoIP Advance Dial Peer Config Manage Update System Manage Account Management Syslog Contig Time Config Logout amp Reboot VoIP Gateway Time Configuration SHTP Timeset timezone GMT 08 00 Beijing Chongging Hong 160 seconds Apply Manual Timeset Server type the ip address of time server Timezone select correct time zone in list box Timeout longest response time for SNTP Manual Timeset
3. 21 2 5 9 Ado Sells eris abre Vo DH S Deo QE Eve 22 YPN 22 240 Sell MOS edes dcdit ttd E EA 24 Zul 2 WAN ADC I E 25 LE MEMES 5 re re 26 29 System Mandag 2 28 2 9 1 28 2 9 2 erates Sano Dua fet eee 28 29a 29 294 LOGOS REDO ates nde td asec 29 Se UNO 30 TOI OOSOID 31 4 1 0 cea rats 31 42 Gopal Comand 32 33 2 42 AG 188 User Manual O CON O NetWork DIAGINOS T A 34 Restore to factory default sse 34 POST Drei dui ue 35 nim 36 How many SIP servers may AG 188N register simultaneously 36 How know the AG 188N s IP 52 36 How to use AG 188N s Lifeline 36 Why the settings vanish after 36 How to use Ihe dial rule
4. WAN port for port mapping Click Add to add new port mapping item and Delete to delete current port mapping item 15 42 AG 188 User Manual 2 5 3 Net Service VoIP Gateway Current State Net Service Hetwork VoIP Advance DHCP Serer REN NAT RTP Initial Port 10000 RTP Port Quantity SIP Digital Map Call Service MMI Filter Audio Settings VPN Dial Peer DHCP Lease Table Config Manage Leased IP Address Client Hardware Address Update System Manage HTTP Port configure HTTP transfer port default is 80 User may change this port to enhance system s security When this port is changed please use http XXX XXX XXX XXX xxxx to reconnect Telnet Port configure telnet transfer port default is 23 RTP Initial Port RTP initial port RTP Port Quantity Maximum RTP port quantity default is 200 Notice Settings in this page won t take effect unless save and reboot the device If you need to change telnet port or HTTP port please use the port greater than 1024 because ports under 1024 is system remain ports HTTP service if HTTP is set to O 16 42 AG 188 User Manual 2 5 4 QoS settings Current State QoS Configuration Network VoIP C VLAN Enable NES YLAN ID Check Enable Voice Data VLAN differentiated Undifferentiated DHCP Server C DiffServ Enable DiffServ Value Net Service Voice VLAN ID 256 0 4095 Data VLAN ID 25 0 4095 0
5. structure user may remain the concerned modules and remove other modules Put the configure file in the root directory of update serve when finish editing Current State Auto Provisioning Configuration Hetwork Advance Server Address Update Config File Name WEB Update Config Encrypt Key FTP TFTP Update Auto Provisioning Protocol Type Update Mode Current Version the system will display the current version number 26 42 AG 188 User Manual Server Address FTP TFTP server address Username FTP server user name Password FTP server password Config File Name The name of configuration file Config Encrypt Key The encrypt key of confirmation file Protocol Type The protocol type that used for upgrading Update Interval Time The interval time that the terminals search for new configuration file Update Mode auto provision mode Disable not auto update Update after reboot auto update after reboot Update at time interval auto update after a certain time Configure file version was in the VOIP CONFIG FILE gt gt and GLOBLE CONFIG MODULE ConfFile Version For instance Gateway original version is lt lt VOIP CONFIG FILE gt gt Version 1 0000 lt GLOBLE CONFIG MODULE ConfFile Version 6 User may edit the configure file version to lt lt VOIP CONFIG FILE gt gt Version 1 0007 lt GLOBLE CONFIG MODULE ConfFile Version 7 27 42 AG 188 User Manual 2 9 System Manage
6. 164 dial plan and customized dial rules Support Lifeline Hotline Speed Dial Call Forward Call Transfer 3 way conference calls Caller ID display DND Do Not Disturb Black List Limit List Upgrade firmware through FTP or HTTP Web management Reverse polarity Telnet remote management Voice prompt adjustable user password and super password Standard and Protocols IEEE 802 3 802 3 u 10 Base T 100Base TX PPPoE PPP Protocol over Ethernet DHCP Client and Server Dynamic Host Configuration Protocol G 711 u a G729 audio Codec SIP RFC3261 RFC 2543 2 TCP IP Internet transfer and control protocol RTP Real time Transport Protocol RTCP Real time Control Protocol VAD CNG save bandwidth 5 42 AG 188 User Manual Telnet Internet s remote login protocol DNS Domain Name Server Trivial File Transfer Protocol HTTP Hyper Text Transfer protocol FTP File Transfer protocol RFC 3362 1 38 protocol 1 6 Compliant Standards CE EN55024 EN55022 FCC part15 comply with ROHS in EU comply with ROHS in China 96 Explanation The letter e is the first letter of environment and electronic The rim is a round with two arrow stands for recycle The number 20 stands for the years of environment protection Please note the years of environment protection is not discarding year nor usage life 1 7 Operating requirement e Operation temperature 0 to 40 C 32 to 104 F e Storage tempera
7. The time setting Daylight Daylight Saving time 2 9 4 Logout amp Reboot Heboot Gateway some setting needs to reboot to make it works Please always save config before reboot otherwise the setting will return to previous setting a ATCOM Current State Network VoIP Advance Dial Peer Config Manage Update System Manage Account Management Syslog Config Time Config VoIP Gateway Reboot System 29 42 AG 188 User Manual 3 IVRsetting User may pre config AG 188N gateway using a normal phone connecting to AG 188N please refer the below command Notice all command below can be end with to speed response reboot gateway 000 clear settings 100 set the IP type to static ip 101 set IP type to DHCP 102 set IP type to 111 prompt gateway ip 14222 prompt phone number Below setting need reboot to take effect 103 change to bridge mode 104 change to router mode 50192 168 1 117 set WAN port IP address 51192 168 1 1 set default gateway IP 52202 112 10 37 set dns server 53255 255 255 0 set netmask use 255 255 255 0 if no be set 30 42 AG 188 User Manual 4 Telnet Console 4 1 Introduce 4 1 1 Basic structure User may use telnet command to access and manage gateway AG 188N adopts tree structure for telnet Every node contains its sub nodes or local command User can type help
8. are Phone Humber Version VOIP Gateway V 1 6 102 21 Mar 26 2008 15 32 50 This page shows AG 188N s running state Network shows the WAN and LAN port connecting state and current settings VoIP show the default protocol the working state of SIP and IAX2 you can see whether AG 188N has registered the public sip server and 2 server Phone Number shows the public sip server the private sip server and the IAX2 server phone numbers 9 42 AG 188 User Manual 2 3 Network 2 3 1 Wan Config VoIP Gateway Current State WAN Configuration Network WAN Contd AdiweiP CurentHetmask MAC Address LAN Config 192 168 1 74 255 255 255 0 00 01 02 03 04 05 192 168 11 VoIP Dial Peer O static DHCP PPPoE Config Manage Obtain DNS server automatically Update System Manage PrefemedDNS DNS 202 96 134 13 Alternate DNS 202 95 128 58 Password WAN port network setting page Support static IP dynamic obtain IP and PPPoE Configure Static IP Enable Static Set AG 188N s IP address in the IP Address Set net mask in the Net mask field Set router IP address in the Gateway DNS Domain Set local DNS server in the Preferred DNS and the Alternate DNS Configure to dynamic obtain IP Enable DHCP If there is DHCP server in your local network AG 188N will automatically obtain WAN port network information from your DHCP server
9. dial rule Phone Number The Number suit for this dial rule cam be set as full match or prefix match Full match means that if the number user dialed is completely the same as this number the call will use this dial rule Prefix match means that if prefix of the number that the user dials is the same as the prefix the call will use this dial rule to distinguish from the full match case you need to add T after the prefix number in the phone number setting Call Mode support SIP and Lifeline SIP means the call will use sip protocol Lifeline means the call will use the PSTN line 36 42 AG 188 User Manual Destination optional call destination can be IP or domain Default is 0 0 0 0 in this case the call will be routed to the Public SIP server If you set the destination to 255 255 255 255 then the call will be routed to the private SIP server Also you can key other address here to make direct IP calls Port optional Configure the port of the destination default is 5060 Alias optional Set up the Alias We support four Alias as below Alias need to co work with the Del Length gt add xxx add prefix to the phone number can set to reduce the dial length all xxx replace the phone number with the xxx can use as speed dial function del delete the first N numbers N is set in the Del Length rep xxx replace the first N numbers N is set in the Del Length For Example Use wants to place a call 8610 6228149
10. 08 SIP Yoice 602 1P Priority 0 0 7 Data 802 1 Priority 0 0 7 Digital Call Service MMI Filter Submit Audio Setting PN Dial Peer Config Manage Update System Manage AG188 implement QoS based on 802 1p The QoS is used to mark the network communication priority in the data link MAC sub layer AG188 will sorted the packets using the QoS and sends it to the destination 1 Voice 802 1p Priority Configure the priority of the voice packets in 802 1p protocol 2 VLAN Enable Disable Enable VLAN function Voice VLAN ID configure the Voice signaling VLAN ID 4 DiffServ Enable Disable Enable Diffserv service 5 DiffServ Value Configure Diffserv parameter The value range value range 0x28 0x30 0x38 0x48 0x50 0x58 0x68 0x70 0x78 0x88 0x90 0x98 0xb8 default is Oxb8 oxb8 stands for best fast transmission 28 30 is guaThrantee for the transmission priority for the 1st rank 48 58 is guarantee for the transmission priority for the 2nd rank 68 78 is guarantee for the transmission priority for the 3rd rank 88 98 is guarantee for the transmission priority for the 4th rank Data VLAN ID Assign VLAN id for data stream Data 802 1P Priority Configure the priority of the data packets non voice signaling data in 802 1p protocol Data Voice DiffServ differentiated undifferentiated for Date and voice VLAN 15 not distinction VLAN tag Tag differentiated for Date and Voice VLAN 15 distinction V
11. 3 then you can set the phone number in the dial rule as 010T and set the Alias as rep 8610 and set the Del Length to 3 Then all calls begin with 010 will be changed to 8610 XXXXXXXX Suffix optional Configure suffix show no suffix if not set Instance VoIP Gateway Current State Dial Peer Network VoIP a Solas SE Oe NAT MMI Filter Audio Settings VPN Dial Peer Config Manage Save Config Clear Config Backup Config Update System Manage Account Management Syslog Config Time Config Logout amp Reboot 2T rule If the call starts with 2 the first 2 will be deleted and the rest number will be sent to private server 3T rule If the call starts with 3 the first 3 will be deleted and the rest number with be sent to public server 123 rule Dial 123 and will send 8675583018049 to your server Used as speed dial function OT rule If the calls is begin with 0 the first O will be replace by 86 Means that if you dial 075583018049 and AG 188N will send 8675583018049 to your server T rule Dial the and the line with switch to PSTN Note that you need to set another rule Prefix Number Length 1 in the Digital Map Refer How to use AG 188N s Lifeline Function 179 rule when you dial 179 the call with send to 192 168 1 179 suit for LAN application without set up a sip server 37 42 AG 188 User Manual How to use speed dial function Please refer to Ho
12. 8 10 1 WoIP System Boot BORRD IHFIHEOH HDHTEK 5128 ATACPU ADN5126 Home Gateway Processor POST Version U1 2 8M SDRAM Creation Date Dec 9 2005 16 16 46 POST Menu Lil Client Download 2 Print Boot Params 131 Clear Config 41 Exit Please enter your number AG 188N provide safe mode When there is booting problem because of setting problem or firmware problem User can restore the factory setting or upgrade to a new firmware to solve this problem How to enter safe mode In the AG 188N booting procedure it use the static ip 192 168 1 179 WAN port IP for a short time user can telnet to this ip address in this occasion to enter the save mode remember to change your PC into the network 192 168 1 xx Then user can according the guide in post mode to clear the settings or upgrade the firmware 35 42 AG 188 User Manual 9 FAQ How many SIP servers may AG 188N register simultaneously AG 188N support 2 SIP servers and a IAX server The Default server is SIP If you want to use the AX server you must set IAX as default protocol in config page IAX and SIP can register simultaneously but not work simultaneously If you set 2 SIP servers in the SIP setting page you can choose the route server by dialing plan which is edited by you Please see How to use the dial rule for detail How can know the AG 188N s IP address Pick up the handset and then dial 111 and AG 188N will pr
13. A is the AG 188N user and B calls and talking with A through VoIP A can press the Hook Flash to hold the call with B and then press and then enter C s number B will be transferred to C and can talk with C gt 3 Way Conference Calls Check Enable Three Way Call Only sip protocol support this function Assume A is the AG 188N user and B calls and talking with A through VoIP A can press Hook Flash to hold the call with B then enter C s number to talk with and then press Hook Flash again switch back to user then A can press to make 3 way conference calls Notice A can press Hook Flash to switch between and or press to cancel the current call and switch to the other user VLAN implement AG188 support rich 802 1Q P protocol and Diffserv configuration Through its flexible VLAN function you can set the voice signaling and data packets in different VLAN via different VLAN Different implement of VLAN function 1 if Data Voice VLAN differentiated is undifferentiated Device will set the same vlan ID for voice and data As show below VoIP Gateway QoS Configuration vLAM Enable VLAN ID Check Enable Voice Data VLAN differentiated Undifferentiated Voice VLAN ID 0 4095 Data VLANID 254 0 4095 Yoine 802 4 F Priority foe Data 802 1P Priority 39 42 AG 188 User Manual VoIP Gateway QoS Configuration Enable Voice Data VLAN differentiated U
14. AG 188 User Manual AG 188N User Manual 1 42 AG 188 User Manual C2 5 PAG FO ATU ES 4 BE APPEN O mmm 4 lee TG E a 4 CS dee eR I S EE 5 P MEE usum MNT 5 ca e 21 and PrOlOCO me 5 126 COMIN otandaldS TM 6 e TR 6 18 PACK AGC M 6 L9 ASTANA ene E dun A E LLL E PLE 0 Web 7 21 ACCESS Wep seling de ee i 7 22 GUNEEN 9 10 2 3 1 10 232 CAN COM 11 214 Et M 11 2 LT IP b 11 24 2 CONN PERTERRITUS 13 2D Advan eel eee ees ee eee LE 14 2 5 1 DACP SEINO UIT 14 292 RCM 15 20 INGE 16 2 54 QOS SeMINGS 17 2 5 5 Advance SIP SCUINGS iiie pde melee ke DM Reps ie ms du exe MUN E EE 18 2 5 6 DIAM a T TIME 19 25 7 Service Sells eene SEO SENI a P ma mE put d 20 2 9 9 omite disti tura isdem
15. DiffServ Enable SINE Ox Voice VLAN ID D 40905 Data VLANID 254 0 4095 voice 802 1P Priority 0 7 Data 802 1P Priority 4 if Data Voice VLAN differentiated is Date untaged and diffServ are both enable Then device will undistinguish the date to VLAN ID setting As below VoIP Gateway QoS Configuration VLAN Enable Voice Data VLAN differentiated data Untaged DiffServ Enable Diffserv Value Voice VLAN ID 0 4085 Data VLAN ID 4095 Voice 8021P Priority 0 7 Data 802 1P Priority 5 if VLAN 15 disable Device won t add any vlan ID to the stream In this case if the Diffserv 1s enable the DiffServ value response to the voice signaling stream 6 When VLAN function is enable If VLAN ID check is enable AG188 will have strict requirement on the VLAN it won t handle any packets with different VLAN ID If VLAN ID check is disable AG188 will handle the packets even from different vlan ID Please notice that VLAN ID check 15 enable in default 42 42
16. LAN tag Date untagged for Date VLAN 15 distinction VLAN tag Please refer to VLAN implement for detail 17 42 AG 188 User Manual 2 5 5 Advance SIP settings VoIP Gateway Current State Advance SIP Configuration Public Registered Private Unregistered STUN NAT Transverse FALSE Hetwork VoIP Advance ooo Serer STUN Server Addr STUN Server Port 3478 DHCP Server HAT Private Server Addr 182 158 1 208 Private Proxy Net Service 008 Digital wm MMI Filter Audio Settings Server Password Proxy Password VPN p Dial Peer z Config Manage STUNEffect Time L dde Private User Agent Voip Phone 1 0 Update n Private Server Type common v Enable URI Convert System Manage Enable Private Register C Enable SIP Stun NN p p This page is used to set the private sip server stun server and back up sip server information STUN Server setting STUN Server Addr configure stun server address STUN Server Port configure stun server port default 3478 STUN Effect Time stun detect NAT type circle unit minute Enable SIP STUN enable disable stun Please refer to sip conf for the setting for how to set the public alter server Private Server Type The particular Private service system supplier carries out the sign and speeches to encrypt default is common User can register two s
17. assword Password of your IAX account Local port Signal port of local default port is 4569 Phone Number Phone number of your IAX account Voice mail number If the AX support voice mail but your username of the voice mail is letters which you can not input with the ATA then you use the number to stand for your username Voice mail text if AX support voice mail config the domain name of your mail box here Echo test number If the platform support echo test and the number is test form the config the test number to replace the text format The echo test is to test the woring status of terminals and platform Echo test text echo test number in text format Refresh time refresh time Enable Register enable or disable register IAX Default Protocol Set AX 2 as the default protocol if not the system will choose SIP as default Enable G 729 Using G 729 speech coding mandatory consultations 13 42 AG 188 User Manual 2 5 Advance 2 5 1 DHCP Server VoIP Gateway Current State DHCP Service Update Mode None DNS Relay Network VoIP Advance Update firmware DHCP Server Update config file NAT Net Service 008 SIP aie 192468401 1440 2552552550 192168101 192168101 ph diua lan 192158101 192 168 10 30 1440 2552552550 19821681041 192158101 Audio Settings VPN E minute System Manage DHCP server manage page User may trace and modify DHCP server
18. ayload length VAD Enable disable Voice Activity Detection FAX Mode select the FAX Mode 2 5 10 VPN lt lt 5 VoIP Gateway Current State VPN Tunnel Network VoIP Advance DHCP Server Digital Map Call Service Filter Audio Settings pen Dial Peer Config Manage System Manage UDP Tunnel L2TP Enable VPN this page is VPN setting page the Gateway support the VPN with UDP and L2TP protocol The parameters is as below VPN IP After VPN registered successfully VPN server will give an IP aggress to the terminal If there is a IP address shown on terminal except for 0 0 0 0 it means your VPN has registered UDP Tunnel 22 42 AG 188 User Manual VPN Server Addr register to the address of VPN server VPN Server Port Register to the port of VPN server Server Group ID the group ID of UDP VPN Server Area Code the are code of VPN server L2TP VPN Server Addr register to the address of VPN server VPN User Name L2TP VPN username VPN Password L2TP VPN password 3 UDP Tunnel CO L2TP Enable PM UDPTunnel use the UDP to visit VPN L2TP use the L2TP to visit VPN Enable VPN Enable the VPN server you must choose UDP or L2TP type in advance 23 42 AG 188 User Manual 2 6 Dial Peer Settings VoIP Gateway Current State Dial Peer Network C 0000 DHCP Serer NAT Net Servic
19. e 005 SIP Digital Map Call Service MMI Filter Audio Settings VPN Dial Peer Config Manage Update System Manage Please refer to how to use dial rule for detail 24 42 AG 188 User Manual 2 7 Config Manage Save Config save current settings Clear Config restore to default settings Notice clear config in admin mode all settings restores to factory default clear config in guest modem all settings except sip advance sip restore to factory default 25 42 AG 188 User Manual 2 8 Update 2 8 1 Web Update update gateway s settings or firmware Firmware file is dlf extension when configure file is cfg extension AG 188N will auto select configure update or firmware update according the extension 2 8 2 FTP Update back up the configure file to FTP or TFTP server Or auto update configure file from your auto update server Back up configure file to your FTP TFTP server VoIP Gateway ATCOM Current State FTP TFTP Download Hetwork VoIP Advance Dial Peer Config Manage Update WEB Update FTP TFTP Update Auto Provisioning System Manage configure use cfg extension 2 8 3 Auto update AG 188N gateway support FTP and TFTP auto update The gateway will auto obtain the configure file from your update server if configured To obtain the original configure file you can use the FTP TFTP back up as describe above Configure file using module
20. e called number is different from AG 188N s phone number No Answer Time no answer call forward time setting Black List incoming call in these phone numbers will be refused Limit List outgoing calls with these phone numbers will be refused 20 42 AG 188 User Manual 2 5 8 MMI Filter VoIP Gateway Current State MMI Filter Network VoIP Advance MM Fiter SS DHCP Serer NAT Apply Net Service 005 SIP Start IP Digital Map Call Service Filt ecccccccecceoceceeeoos Audio Settings VPN Br UJ Dial Peer NE Update System Manage MMI filter is used to make access limit to AG 188N Gateway When MMI filter is enable Only IP address within the start IP and end IP can access AG 188N gateway 21 42 AG 188 User Manual 2 5 9 Audio Settings Current State DSP Configuration Network VoIP CODEC g711Alaw64k Signal Standard CHINA Advance Input Volume 0 Output Volume 0 DHCP a dim G729 Payload Lenath 10 Payload Type Net Service i Q7 ilBC Payload Type 97 SIP CallerID Tx Mode Sk FAX Mode 38 Digital E MMI Filter Audio Settings VPN Apply Dial Peer Config Manage Update System Manage CODEC select the prefer CODEC support ulaw alaw and G729 Signal Standard Support CHINA Japan and USA standard Input Volume Handset in volume Output Volume Handset out volume G729 Payload Length G729 p
21. er Username number Register Password common Server Type User Agent Voip P hone 1 0 v d Signal Encryt C Enable PRACK O Rtp Encryt Enable Keep Authentication C Enable Session Timer C Auto Detect Server Answer With Single Codec Enable Via rport SIP Default Protocol v Enable Register E Register address of public SIP server Register port of public SIP server Username of your SIP account Always the same as the phone Password of your SIP account 11 42 AG 188 User Manual Proxy Server Addr IP address of proxy SIP server SIP provider always use the same IP for register server and proxy server in this case you don t need to configure the proxy server information Proxy Server Port Signal port of SIP proxy Proxy Username proxy server username Proxy Password proxy server password Domain Realm SIP domain enter the sip domain if any otherwise AG 188N will use the proxy server address as sip domain Local SIP port Local SIP register port default 5060 Phone Number Phone number of your SIP account Register Expire Time register expire time default is 600 seconds AG 188N will auto configure this expire time to the server recommended setting if it is different from the SIP server Detect Interval Time Co work with the Auto Detect Server if Auto Detect Server is enable AG 188N will periodically detect if the SIP server is available according this settin
22. g RFC Protocol Edition Current AG 188N SIP versions Set to RFC 2543 if the gate need to communicate to devices such as CISCO5300 using the SIP 1 0 Default is RFC 3261 Enable Register Enable Disable SIP register AG 188N won t sent register info to SIP server DTMF Mode DTMF signal sending mode support RFC2833 DTMF RELAY inband audio and SIP info Auto Detect server co work with Server Auto Swap and Detect Interval Time Enable this option AG 188N will periodically detect whether the public SIP server is available if the server is unavailable the AG 188N will switch to the back up SIP sever and continue detecting the public sip server AG 188N will switch back to the primary SIP server if the server is available again Server Auto Swap Please refer to Auto Detect server for detail Enable Via rport config the supporting for RFC 3581 SIP Default Protocol Setting for the default protocol of SIP 12 42 AG 188 User Manual 2 4 2 lax2 Config VoIP Gateway ee CN ATCOM Current State lIAX Unregistered Configuration Hetwork VoIP SIP Config Advance Dial Peer Config Manage Update System Manage C Enable Register C Enable G 729 Setting page of public IAX server Server Addr Register address of public IAX server Server Port Register port of public server default port is 4569 Account Name Username of your SIP account Always the same as the phone number Account P
23. information in this page Update Mode Using DHCP updated model None expressed are not updated Update firmware update firmware 15 used to DHCP Update file 15 used to configure DHCP updated configuration files Tftp Server Addresses using TFTP server upgrade DNS Relay enable DNS relay function User may use below setting to add a new lease table Lease Table Name Lease table name Lease Time DHCP server lease time Start IP Start IP of lease table End IP End IP of lease table Network device connecting to the AG 188N LAN port can dynamic obtain the IP in the range between start IP and end IP Netmask Netmask of lease table Gateway Default gateway of lease table DNS default DNS server of lease table Notice This setting won t take effect unless you save the config and reboot the device 14 42 AG 188 User Manual 2 5 2 NAT P nmm Uu ATCOM Current State Network VoIP Advance t oot Dial Peer Config Manage Update System Manage VoIP Gateway NAT Configuration IPSec ALG FTP ALG PPTP ALG Apply Advance NAT setting Maximum 10 items for TCP and UDP port mapping IPSec ALG Enable Disable IPSec ALG FTP ALG PPTP ALG Transfer Type Inside IP Inside Port Outside Port Enable Disable FTP ALG Enable Disable PPTP ALG Transfer type using port mapping LAN device IP for port mapping LAN device port for port mapping
24. ip servers public sip server and private sip server these two sip servers are independent from each other and running in the same time For how to configure private sip server Please refer to Sip configuration 18 42 AG 188 User Manual 2 5 6 Digital Map VoIP Gateway ATCOM Current State Digital Map Configuration Network VoIP End with i Advance FixedLength 11 DHCP Server NAT Net Service 005 SIP Time out 5 Digital Map Call Service MMI Filter Audio Settings VPN Digital Map Table Dial Peer Config Manage Prefix Number Update p amp 3 8 K XXXX System Manage Digit map is a set of rules to determine when the user has finished dialing AG 188N support below digital map Digital Map is based on some rules to judge when user end their dialing and send the number to the server AG 188N support following digital map End With Use as the end of dialing Fixed Length When the length of the dialing match the call will be sent Timeout Specify the timeout of the last dial digit The call will be sent after timeout Prefix User define digital map represents the range of digit can be a range such as 1 4 or use comma such as 1 3 5 or use a list such as 234 X represents any one digit between 0 9 Tn represents the last digit timeout n represents the time from 0 9 second it is necessary Tn must be the last two digit in the entry If Tn is not inc
25. luded in the entry we use TO as default it means system will sent the number immediately if the number matches the entry Example 1 8 xxx All number from 1000 to 89999 will be sent immediately 8 digits numbers begin with 9 will be sent immediately 911 Number 911 will be sent will be immediately 99xT4 3 digits numbers begin with 99 with be sent after four seconds 19 42 AG 188 User Manual 2 5 7 Call Service Settings VoIP Gateway ATCOM Current State Call Service Network VoIP Advance Call Forward DHCP Server rw ott O Busy O No Answer O Always NAT Net Service part 5050 005 Forward Number Config Manage Remote Record d Use Record Server Update System Manage User configure the value add service such as hotline call forward call transfer 3 way conference call etc in this page Hotline configure hotline number AG 188N immediately dials this number after hook off if it is set Call Forward Please refer to value add service for detail No Disturb DND do not disturb enable this option to refuse any calls Ban Outgoing Enable this to ban outgoing calls Enable Call Transfer Please refer to value add service for detail Enable Three Way Call Please refer to value add service for detail Enable Call Waiting Enable disable Call Waiting Accept Call If this option is disable AG 188N refuse the incoming call when th
26. ndiffare ntiated DiffServ Enable DiffServ Value 0 s LAT ID 0 4085 Data VLAN ID 0 4095 Vice 802 Priority lu le Data 8024P Priority 2 if Data Voice VLAN differentiated is Tag differentiated but the DiffServ is disable Device won t distinguish the voice signaling and data stream It will add the same data vlan id to them As below VoIP Gateway QoS Configuration VLAN Enable VLAN ID Check Enable Yoice Data VLAN differentiated Tag differentiated v DiffServ Enable DiffServ Value Ox Voice LAN ID 4095 Data LAM ID 254 fo 4095 Voice 802 Priority 0 7 Data 802 Priority 0 7 Or 40 42 AG 188 User Manual VoIP Gateway QoS Configuration Enable Voice Data VLAN differentiated differentiated i 0 iori 7 Voice LAN ID 256 0 _4n9s Data VLAN ID D 4095 Voice 802 1 P Priority 0 7 Data 802 1P Priority 3 if Data Voice VLAN differentiated is Tag differentiated and diffServ are both enable Then device will distinguish the voice signaling and data stream to VLAN ID setting As below VoIP Gateway QoS Configuration LAN Enable VLAN ID Check Enable Voice Data LAN differentiated Tau differentiated 41 42 AG 188 User Manual VoIP Gateway QoS Configuration VLAN Enable VLAN ID Check Enable Voice Data differentiated Tad differentiated
27. omote you its IP address How to use AG 188N s Lifeline function AG 188N supports Lifeline function you can use the same handset to place PSTN and VoIP calls First you need to set up the Lifeline with the accessory send with the AG 188N connect this accessory to AG 188N s FXS port and then connect the handset to the accessory s phone port connect the landline to the accessory s line port You can receive PSNT and VoIP calls simply with configuration To place the PSTN call you need to set up as follow Add a new dial rule in the Dial Peer setting set the phone number to T and choose the Lifeline as the Call mode Add new Digital map item in the Advance Digital Map set Prefix Number to and and the length to 1 Then when you want to place a PSTN calls you can first press to switch to the PSTN line and then place your call as you normal do Why the settings vanish after reboot Please go to Config Manage Save Config to save your setting always How to use the dial rule AG 188N provide flexible dial rule with different dial rule configure user can easily implement the following function Replace delete or add prefix of the dial number Make direct IP to IP call Place the call to different SIP server according the prefix Make PSTN calls use Lifeline function Please refer How can use the Lifeline function of AG 188N You can click Add to add a new dial rule Below is the detail setting of the
28. or whenever to see sub nodes and all local command under current node Besides local command there are some global commands can be used in each node 4 1 2 Basic command Logout exit telnet mode Write save current settings Type sub nodes name in current node to switch to sub node Type or exit in current node to return to parent node Type help or can see all sub nodes and all local command under current node every item has comments such as command or node to distinguish sub nodes and local command Type help or in command can see all parameters using in this command When typing node name or command user no need to key the full name use TAB button will make it more efficient There are two types in command parameters optional and required required parameter use as prefix and optional use _ as prefix User may type or _ then press TAB button for complementarily 31 42 AG 188 User Manual 4 2 Global Command Global command is available under all nodes AG 188N support following commands Ping command use to check network ping www google com 32 42 AG 188 User Manual 5 Tree Structure 5 1 1 Debug Level 0 7 path lt debug gt show debug setting Show disablelenable debug all modules no all xxx disablelenable debug app module NO app xxx disable enable debug cdr module no cdr xxx di
29. sablelenable debug sip module NO sip xxx disablelenable debug tel module no tel xxx disablelenable debug dsp module no dsp xxx 5 1 2reload usage reload Reboot system 5 1 3 show system running info basic path show show network status Example lt show gt basic Show ip packets Stat Example lt show gt ip ip Show RTP packets Stat Example lt show gt ip rtp Show TCP packets Stat Example lt show gt ip tcp Show UDP packets Stat Example lt show gt ip udp gt memory path lt show gt show gateway memory Example lt show gt memory gt nat path lt show gt show NAT information Example lt show gt nat 33 42 AG 188 User Manual gt uptime path lt show gt show running time Example lt show gt uptime gt version path lt show gt show gateway version Example lt show gt version 5 1 4telnet and logout Usage telnet target port Login xxx Password xxx logout 5 1 5 tracert trace network path info usage tracert host Example tracert www google com 6 Network Diagnosis There are some telnet commands for checking your network Now Listing below for your information Check if the destination is accessible ping www google com 7 Restore to factory default setdefault clear gateway settings expect network part setdefault all clear all settings 34 42 AG 188 User Manual 8 POST Mode safe mode Telnet 192 16
30. tea ue ete Ete atu 36 How to use speed dial function 38 How to configure digital map 38 How to use Call Forward Call Transfer and 3 way Conference calls 38 VELAN eciam N E 39 3 42 AG 188 User Manual 1 AG 188N Features 11 Appearance PWR power connection status SYS server registration status registered gliting not registered off WAN WAN port connectiong contected on offline off LAN LAN port connectiong contected on offline off PSTN light on when PSTN call come in out VoIP light on when VoIP call come in out The default status when pick up the call is VoIP call out 1 2 Interface Power Output Power 12VDC 500mA Port RJ11 port Connect to handset or the Lifeline accessory WAN RJ45 port LAN RJ45 port 4 42 AG 188 User Manual 1 3 Electricity characteristic Speciality of electric output the 12V 500mA DC The network connects 2 RJ45 connect a WAN a LAN FXS 2 port 1 4 Software Support two sip servers running at the same time Back up sip server support NAT Firewall DHCP client and server Support PPPoE used for ADSL cable modem connecting Support major G7 xxx CODEC VAD CNG G 165 compliant 16ms echo cancellation Tone generation and Local DTMF re generation according with ITU T E
31. ture 30 to 65 C 22 to 149 F e Humidity 10 to 90 no dew 1 8 Package e Size 128 x 85 x 30 mm e Packing List v AG 188N gateway v Power adaptor 12v 500mA v Manual CD 6 42 AG 188 User Manual 1 9 Installation Use Ethernet cable to connect AG 188N s LAN port and your computer Set your computer s ip to the network 192 168 10 x or using dynamic obtain IP Open your web browser and key in 192 168 10 1 Then you will see the logon page of AG 188N the default username and password is admin admin for administrator and guest guest for guest Set up page for VoIP use only Power POS Phone User 2 Web Configuration 2 1 Access Web setting page Enter AG 188N IP address in the web browser and press ENTER to go to the log on page and key in the username and password to access AG 188N setting page Default username and password is Administrator Username admin password admin User Username guest Username guest 7 42 AG 188 User Manual 8 42 AG 188 User Manual 2 2 Current state VoIP Gateway Current State Running Status Network Network VoIP Connect Mode DHCP MAC Address 00 01 02 03 04 05 Address 192 168 1 74 192 168 1 1 EBENE Primary DNS 202 96 128 166 Alternate DNS 202 96 134 133 Dial Peer Address 192 168 10 1 DHCP Server ON o Config Manage Update Default Protocol SIP System Manage server Register Server 194 54 102 147 Proxy Server 194 54 102 147
32. w to use dial rule How to configure digital map Please refer digit map settings How to use Call Forward Call Transfer and 3 way Conference calls User may set up the configuration in the Call Service page to use these value add service VoIP Gateway Call Service Call Forward 9 oi Busy Q Answer Always Forward Number IF Port 5060 d Disturb Outgoing d Enable Call Transter d Enable Call waiting Enable Three Way Call Accept Any Call Answer Timelseconds P2P IP Pretix oY Remote Record Use Record Server N 0 0 0 0 0 Call Forward Forward when busy select Busy in the Call Forward Field and Key in the destination phone number in the Forward Number If some one calls you when you having a call the caller will be forwarded to the destination number Forward no answer Select No Answer in the Call Forward Field and Key in the destination phone number in the Forward Number fill the time in the No Answer Time If some one calls you and no one answer the caller during the No Answer Time the call will be forward to the destination number Forward Always Select Always in the Call Forward Field and Key in the destination phone number in the Forward Number then any one calls this gateway will be forward to the destination 38 42 AG 188 User Manual number gt Call Transfer Check the Enable Call Transfer If
Download Pdf Manuals
Related Search