Home

MPC6515

1. ENGLISH Select the language as you prefer 5 5 Work interface Press Start to enter the Work interface as below AAA 100 100 100 0 0 15 File File name Speed Percentage of the processing speed Power Percentage of the processing power Time Elapsed time When processing Press and n adjust the percentage of the processing power only for Power not for Corner Power Value should be from 0 100 Press A and to adjust the percentage of the processing speed Value should be from 0 100 Press Start Pause to start or pause the processing Press Stop to cancel the processing The user interface shows Stopped Press Esc to back to the main user interface Press the button Start Pause during the processing to shift between commands such as start and pause The pause interface is as below PAUSED PRESS START PAUSE TO CONTINUE When the Pause interface is displayed as the above only Start Pause and Stop buttons are effective Press the button Start Pause twice to return to the Work interface 15 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Press Stop to cancel the work User interface displays as below STOPPED When the Stop interface is displayed as the above only Start Pause Esc and A V buttons are effective Press the button Start Pause to enter the Work interface If you want to set the parameters press Esc to return to the main interface Press A
2. MANUFACTURER MANUAL MPC6515 V 2 0 Step Servo Co Ltd Building 8 B Dayi Zone of Incubating Hi Tech No 1 South 2nd Keyuan Rd Chengdu 610041 CHINA www leetro com Copyright The content of this manual has been carefully prepared and is believed to be accurate but no responsibility is assumed for inaccuracies Step Servo Co Ltd reserves the right to make changes without further notice to any products herein to improve reliability function or design Step Servo Co Ltd does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under its patent rights of others Step Servo and Leetro are trademark of Step Servo Co Ltd Step Servo Co Ltd s general policy does not recommend the use of its products in life support or aircraft applications wherein a failure or malfunction of the product may directly threaten life or injury Per Step Servo Co Ltd s terms and conditions of sales the user of Step Servo Co Ltd products in life support or aircraft applications assumes all risks of such use and indemnifies Step Servo Co Ltd against all damages I MPC6515 Laser Engraving amp Cutting Controller User Manual V 2 0 Table of Content CHAPTERT PREFAGE z o n 1 CHAPTER 2 OVERVIEW ccccccccccccccscccccccccsccccccscccsccccccccccececs 2 2 1 MPC6515 INTRODUCTION iiidh t eee i eee eee re
3. e Wiring of J2 and EasyView RS232 PLC EasyView PLC MPC6515 J2 2 lt il 2 o di 5 5 e Wiring of J2 and PAD03 RS232 PADO3 MPC 6515 J2 0 i Ho di ieri 9 NO Ur UY e Wiring of J2 and BYDseries HMI RS232 PLC BYDseries HMI PLC MPC6515 J2 2 2 3 3 5 5 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 4 2 MPC6515 MC V2 0 Interfaces D1 Working Status D2 Z axis D3 Y axis D4 X axis D5 8 Error Coders O version of circuit board is V1 0 user cannot find version Q Please pay attention to the version of MPC6515 MC If the number in the circuit board Caution MPC6515 Hardware Interfaces Pin Array 1 2 3 4 5 6 X1 24VDC 2A 24V GND X2 Pedal Switch Uncapping Reserve a 5V 24V protection GND Z axis i Z axis Z axis 5V 24V X3 Forward Reverse Limit Origin GND Met Limit Y axis A Y axis Y axis 5V 24V X4 T Reverse Limit Origin GND d X axis y X5 Forward p X axis X axis PUN 5V 24V Limit everse Limit Origin GND USB Flash Yi Blow off seria Disk Reserve o 5V 24V Indication v2 Laser Power Analog Laser Laser GND Output Power On Off Z axis Y3 Z axis Pulse Direction 5V GND 5V Y4 Y axis Pulse LAS 5V GND 5V irection i X axis Y5 X axis Pulse Direction 5V GND 5V POWER Input Power Pin 24VDC Note MPC6515 adopts single 24VDC power supply The other power pins ar
4. Upgrade the version of MPC6515 to V4 1 0 0 or above 9 7 Control Two Laser Heads Functionality Control power of two laser heads independently Instruction Upgrade MPC6515 to V4 1 0 0 or above Upgrade software to V2007 3 3 or above Set power mode to LaserPowerMode 4 and set the distance of two laser heads 30
5. correct 8 D controller i e MPCOSGA controller Oxel IAE RSAC firmware is used for MPC6515 by mistake Download data exceeds the Delete the unneeded g rest memory size of files in the controller 0xd0 BR N E MPC6515 memory and re download the processing file This is a data transmission Re download data ig 1 error possibly occurs in the Oxd2 eseje i ei process of downloading This error occurs when 1 Restart MPC6515 there s too much data being 2 If the error can t be transmitted between eliminated by g A PAD03 and MPC6515 following the 1 step 0xd3 eletorelcilollele through the serial port replace the PAD03 3 If the error can t be eliminated by following the 2 step return the controller to the supplier for repair 1 Replace the USB communication cable if this error occurs 8 USB interface frequently Oxdf elle Sile elle e communication timeout 2 Try on another PC if the error cant be eliminated by the 1 step 3 Return the controller to the supplier for repair if the error can t be eliminated by the 2 step Config file error This error Re download correct 8 occurs when the cfg file is configuration file Oxf1 e elle e o o o e incorrect or the user forgets to download the cfg file Mismatched firmware file Re download correct 8 DI fmw and hardware file fmw file and hdw file Oxf ejelejejojolejo Gehdw Error Code Caution Please resta
6. flashes Error Code Description Following Error Code list will direct you to the error causes and solutions D1 D8 LEDs indicate an 8 bit status and form 1 byte i e when D8 D7 and D6 keep shining while the other indicator lights are off the corresponding error code is 0xe0 when D1 to D4 are off D5 to D8 are shining the corresponding error code is Oxf0 ON OFF status indicated by following symbols 24 Error Code Indicates the light is shining 2 Indicates the light is off Error codes descriptions are as below 25 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Error Code Lights Status Causes Solution Mismatched process file Replace the function config file and firmware library with the correct 8 version one that matches with Oxe0 PLL This error is possibly the firmware version caused by forgetting to and re download the re download the config file processing file and after the firmware config file upgrading Mismatched firmware and Change to
7. Human machine interface will also display the downloading status 23 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 8 Error Code 8 1 Indicator Light Description Working status of MPC6515 is indicated through the 8 LED indicator lights in MC card and 4 indicator lights in CPU card Please refer to Chapter4 to learn the placement of indicator lights Indicator lights in CPU card D1 indicate the working status of USB slave interface It s normally flash green quickly D2 indicate the working status of USB slave interface It s normally flash green slowly D3 indicate the operating status It keeps shining green when processing graphics or downloading data from USB sticker and stops shining when the processing or downloading is finished D4 No use Indicator lights in MC card D1 When MPC6515 is powered on and started D1 keeps shining D2 indicate pulse output status of Z axis D2 keeps shining when Z axis is outputting pulses and stops shining when outputting is finished D3 indicate pulse output status of Y axis D3 keeps shining when Y axis is outputting pulses and stops shining when outputting is finished D4 indicate pulse output status of X axi D4 keeps shining when X axis is outputting pulses and stops shining when outputting is finished D8 When the CPU mainloop of CPU card works normally D8 flashes D7 When data is transmitted between PADO3 and MPC6515 D7
8. PC to Standard active the installed LaserCut software 7 HMI TPC7062KS 1 7 inch TFT Touch HMI English Optional 800x480 Res 65K Color CE FCC 8 HMI C9 3M 1 Cable connects MPC6575 and Optional HMI TPC7062KS Length 3meters 9 PADO3 TR 1 Operation Panel Turkish Optinonal MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 3 Intallation 3 1 Mainboard The mainboard adopts six M3 bolts Intallation 3 2 PAD03 100 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 4 MPC6515 Hardware Interfaces MPC6515 controller is composed of two parts 1 MPC6515 MC motion control daughter board 2 MPC6515 CPU CPU mainboard User can find corresponding mark on each board 4 1 MPC6515 CPU Interfaces J2 Human Machine Interface Support HMI based on Modbus Protocol USB slave interface Connect to PC to download data Main USB interface Download data from flash memory disk Indicate light for data downloading and operating J2 HMI RS232 support HMIs such as EasyView BYDseries HMI PADO3 etc based on Modbus Protocol MPC6515 Hardware Interfaces J2 adopts DB9 pin plug Pin2 Pin3 Pin5 and Pin9 are used Pins 1 2 3 4 5 6 7 8 9 Description TXD RXD GND 5V
9. V to generate jogging motion according to the completed parameter settings When the processing is finished only Start Pause and Esc buttons are effective Press Start Pause to enter the work interface Press Esc to return to the main interface 5 6 Download from USB Sticker Return to the main interface and plug the USB sticker into the controller User interface of PADO3 displays as below DETECTING USB FLASH DISK Once the USB sticker is detected without error the controller starts downloading the processing file from the USB sticker User interface of PADO3 displays as below DOWNLOADING STATUS 000 When the download is finished the buzzer starts ringing User interface displays as below DOWNLOAD COMPLETED REMOVE USB FLASH DISK 16 PADO3 Operation Once the USB sticker is pulled out the ringing ceases Caution USB flash disk should be formatted to FAT16 if fail to follow this instruction the flash disk cannot be detected by the controller 17 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 6 HMI Development All HMIs that support Modbus Protocol can be developed to the control panel of MPC6515 i e MT506LV45WV 6 1 Protocol and System Setting Standard Modbus Protocol PLC Type Modbus RTU Baud rate 9600bps Data bit 8 bit Stop bit 1 bit Verify None 6 2 Address Address and function descriptions of PLC relay s
10. and the Power Pieces The value indicates how many pieces of the same work you want Del Delete the file Press 1 o to select the option you want to edit Selected option will be highlighted Press A or Vio set the value of selected option such as the processing speed value the corner power the standard power and pieces Press to save the edited settings To exit the edit interface press Esc till no option highlighted Having completed the settings user can Pre E A Y to move the laser head Or press to enter the edit interface again Remark1 Press to complete the settings on speed power and pieces The completed settings will not be lost even the power is off 12 PADO3 Operation Press ESC till cursor disappears to continue the following steps To draw lines hold down Laser button and press D A V Press Laser to beam according to the settings of LASER SET Press Datum to start the homing motion of X axis and Y axis simultaneously DATUM X and Y axes will not stop until they reach the origin point or the user press Stop button Press Test to generate the contouring motion and following text displays BORDERING PLEASE WAIT When bordering finished press m to return to the main interface Press Z button text displays as below Z AXIS OPERATE Press Mor Vto generate Z axis jogging Press Datume to start the homing motion of Z axis Press Stop to stop the homing motio
11. ceive 2 2 2 CONTROL SYSTEM CONFIGURATION cccccsssseccccccscccccccsssesccccsaeccccecssssseceeeeecess 2 Zo IMPG6OILSPACK LIST srt 3 CHAPTER 3 INTALLATION ssscccrrrrsseesesececceseseseeeecececeecese 4 Jal tMAINBOARD sirena comedo Zas Sava ob kv 4 3125 PATIOS AL I alleate u 5 CHAPTER 4 MPC6515 HARDWARE INTERFACES 6 4 1 MPC6515 CPU INTERFACES ccsseccccccscccccccssssccccccscccceccsssssseccesececceeeaeesceeeees 6 42 MPC6515 MC V2 0 INTERFACES ccccssseccccccsssssccccececcceccsssssccccesececeseuaessceeeees 8 CHAPTER 5 PADO3 OPERATION ssssccrerrrssesceseseccose 11 P RS EOIN E h OIN chee cede lo 11 52 STARTUP MESSAGE id ds 12 137 MAIN INTERFACE as 12 5 4 SUPPORTING NT R AOA a a E Ea E a a A EA ESEA 14 D S 0 A NA H E a SN CE E aa 15 5 6 DOWNLOAD FROM USB STICKER ccccccnconccccnnnonocnnnnnnnconncononnnnccnnnononnccnonnnnccnnnonanos 16 CHAPTER 6 HMI DEVELOPMENT sessrssrcccssssseezeseceso 18 6 1 PROTOCOL AND SYSTEM SETTING ccceccccccssssecccccssccccccsssseccecseeccccscesssssceeesausess 18 6 2 ADDRESS siente A Hv 18 CHAPTER 7 DOWNLOAD DOCUMENT oorrrsrsrererereso 22 LA UPDATE FIRMWARE ia 22 H2 DOWNLOAD DATA cid 23 CHAPTER 8 ERROR CODE occccccccccococococoococcocococononononcnnonononos 24 8 1 INDICATOR LIGHT DESCRIPTION ssssecccccsssccccccsssseccccsesccccccessescecesaececeeasans 24 Eror Code Desc
12. cts without understanding this manual Prohibited Do not disassemble modify nor repair the Products without being authorized Prohibited Do not subject the Product to water corrosive or flammable gases and combustibles Prohibited MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 2 Overview 2 1 MPC6515 Introduction The MPC6515 controller is a stand alone control card specially designed for the control system of laser engraving and cutting machines User can edit graphics set parameters and optimize path to develop a process file using computer If you want to use DSP5 0 to control the motion please connect MPC6515 to PC using the USB connect cable in the pack 2 2 Control System Configuration Please see the following diagram on MPC6515 motion control system Transfer pale data es E or m Screen lar Overview 2 3 MPC6515 Pack List No Model QTY Description Type 1 MPC6515 1 Control Board Standard Flash momery upgrades firmware and Standard 2 Udisk 1 downloads data to MPC6515 USB sticker cable USB AA 1 5M is included 3 USB AB 3M 1 Cable connects PC and MPC6515 Standard Length 3meters 4 C4 PAD03 1 5M 1 Cable connects PADO3 E and Standard MPC6515 Length 1 5meters 5 PAD03 E 1 Operation Panel English Standard 6 Dongle WHITE 1 Software key USB interface in
13. e output power of the controller Warning MPC6515 adopts single 24VDC User must use proper and reliable power supply Exorbitant voltage could result in damage of components while low voltage could result in problem in operation S Prohibited JP 1 Note JP1 is related with X3 X4 and X5 If 24V voltage is required for input signal ports X3 X4 and X5 the jumper should connect Pini and Pin2 If 5V voltage is required the jumper should connect Pin2 and Pin3 If the jumper is removed Pin5 of X3 X4 and X5 not connected JP2 The output power of the above pins should be used only for the common anode and common cathode of control signals and should not be used as the power supply for motor drives Failure to observe this instruction could result in damage of the controller MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Note JP2 is related with Y2 For analog control laser power remove the jumper connect laser power to Pin2 For PWM control laser power connect the power to Pin3 JP3 Note Jumper JP3 can be used for controlling the output 5V 24V from the MPC6515 If the output terminal Y1 is to be used for driving 24V relay move the jumper to P1 P2 If the output terminal Y1 is to be used for driving 5V relay move the jumper to P2 P3 When the jumper is removed P6 of Y1 should be disconnected JP4 Note JP4 is related with X2 If 24V is required for the g
14. eneral input X2 the jumper should connect Pini and Pin2 If 5V voltage is required the jumper should connect Pin2 and Pin3 If the jumper is removed Pin5 of X2 not connected Pin 3 and Pin4 of Y3 Y4 and Y5 is output 5V power of MPC6515 can be the common anode for motor drive Do not connect external 5V to Pin3 and Pin4 Warning The rated currency of general purpose output is 100mA The loaded device should be approved and reliable Warning Common ground O GND of laser power should connect Pinl of Y2 All inputs and outputs are singl ended Caution 10 PADO3 Operation Chapter 5 PAD03 Operation 5 1 Connection Connect MPC6515 J2 to PADO3 RS232 PADO3 MPC6515 J2 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 5 2 Startup Message When the power is on following message will be displayed V3 0 10 is the version number of PADO3 SYSTEM IS STARTING PLEASE WAIT V 3 0 10 5 3 Main Interface If there s no communication problem with MPC6515 main interface will be shown as below File The saved file name loaded to MPC6515 controller Speed Percentage of processing speed When it is 100 the actual speed is the number which is set in processing data Power Percentage of processing power When it is 100 the actual power is the number which is set in processing data There are two options such as the Corner Power
15. er corresponding to low speed 4 4x BIN 16 1 Set the pieces to be processed 5 4x BIN 16 1 Reserve 6 4x BIN 16 1 Pieces has been processed 7 4x BIN 16 1 Reserve 8 4x BIN 32 2 Shooting time low 16 Shooting time Unit bit mm 9 Shooting time high 16 bit 10 4x BIN 16 1 Jogging distance 11 4x BIN 16 1 Reserve 12 4x BIN 16 1 Reserve 13 4x BIN 16 1 Shooting time 14 4x BIN 16 1 Shooting power 15 4x BIN 16 1 Pieces of files downloaded to the controller 16 4x BIN 16 1 File number 17 4x 64 4 File name abcdefgh 8 bytes shown in text mode 21 28 4x BIN 16 1 Reserve 29 4x BIN 16 1 Processing time h 30 4x BIN 16 1 Processing time m 31 4x BIN 16 1 Processing time s 32 4x BIN 16 1 Working status 33 4x BIN 16 1 Download progress with USB flash disk 20 HMI Development Please see following description on each bit Address 32 F E D C B A 9 8 1 under jogging 0 stop jogging 7 6 5 4 3 2 1 0 1 start 1 plug 1 back 1 back 1 cut 1 1 start 1 downloading in USB to to contour contouring 0 stop pause 0 download flash home home 0 0 0 completes disk 0 stop 0 stop finished finishied resume 0 remove the USB flash disk 0x0002 under processing 0x0003 pause 0x0004 contouring 0x0008 cutting contour 0x0010 0x0020 0x0040 0x00c0 0x0080 0x0100 XY axes are restored Z axis is restored USB flash disk is detected downloadin
16. g data from USB flash disk download successful remove the USB flash disk under jogging Each value of the status register corresponding to specific status 21 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 7 Download Document For user s convenience the firmware update file processing file and configuration file can be downloaded conveniently using USB flash disk 7 1 1 6 Update Firmware Copy the updated firmware data FM FMW and 05LM201 HDW to the root directory of USB flash disk FAT16 format Recommendation do not save other files to the flash disk Electricify MPC6515 the indicate light D1 on MPC6515 CPU will flash twice swiftly Plug USB flash disk into MPC6515 within 5 seconds after D1flashed twice If D1 keeps shining for 2 5 seconds depending on the size of firmware update file the firmware is being updated If there s a indicate light in USB flash disk user can tell if the data is being read through the indicate light D1 flashed swiftly firmware is updated successfully If there s a indicate light in USB flash disk user can tell if the update is finished through the indicate light After removing the USB flash disk DSP firmware program will be started If MPC6515 fails to work it s probably that something s wrong during the update process Please repeat the above update steps or contact your supplier User should update the firmware only when
17. hown as below 18 HMI Development Address Cr ra Function Type Remarks 1 0x ON Start Pause Button 2 0x ON OFF Pause Button switch 3 0x ON Resume Button 4 0x ON Stop Button 5 0x ON OFF Up Button 6 0x ON OFF Down Button 7 0x ON OFF Left Button 8 0x ON OFF Right Button 9 11 0x Reserve 12 0x ON Z axis restoration Button 13 0x ON XY axes restoration Button 14 0x ON Speed 1 during processing Button 15 0x ON Speed 1 during processing Button 16 0x ON High Speed Power 1 during Button processing 17 0x ON High Speed Power 1 during Button processing 18 0x ON Contouring Button 19 0x ON Cut contour Button 20 0x ON OFF Shoot Button 21 0x ON OFF Z axis jogs in positive direction Button 22 0x ON OFF Z axis jogs in negative Button direction 30 0x ON Delete the file Button 31 0x ON Go to the next file Button 32 0x ON Go to the previous file Button 33 0x Status 1 in processing 0 Status process finished 19 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Address and function descriptions of PLC register shown as below Address Components Da Da oie Function Type bit byte 1 4x BIN 16 1 Percentage o f processing speed 2 4x BIN 16 1 Laser power corresponding to high speed 3 4x BIN 16 1 Laser pow
18. n external indicator light could be connected to show the processing status The external indicator light can be used to lead the processing status signals to the machine panel and show the status with LBD or drive other indicator lights through circuit Instruction Use Pin2 of Y1 on MPC6515 MC light signal indicating process completion to drive the relay or LBD 9 4 Blow off Functionality Blow off switch can be controlled through I O interface to blow off the heat and ash produced during the laser engraving and cutting Instruction Pini of Y1 can be used as the I O interface controlling blow off User can control the 29 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 status of Pin using processing commands When the interface is low level blow off is on When the interface is high level blow off is off 9 5 Grade Engrave Functionality In accordance with the functionality of PCI bus controller MPCO3L Instruction The version of MPC6515 is required to be V4 1 0 0 or above Version of software should be V2007 3 3 or above Set the process mode as Grade Engrave on the software MPC6515 V4 1 0 0 supports PWM grade engrave and 1 ch analog grade engrave 9 6 Software Limit under Immediate Mode Functionality This functionality is effective only on the premise that the machine has been to the origin point Machine will auto detect if the process exceed worktable before output Instruction
19. n of Z axis Press Zto return to the main interface Text displayed when Z axis is homing Z AXIS DATUM Z axis will not stop until it reaches the origin point or the user press Stop button 13 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 5 4 Supporting Interface Press Menu to enter the supporting interface as below CUT BDR PMOV SET LANGUAGE CUT BDR Laser head will move a rectangle with laser on according to the size of the graphics LAS SET Select this option and press om to enter the LAS SET interface as below LASER TIME SET MS POW 000000 000000 Press or D to move the cursor Press A or V to modify the number Press to save the settings If this value is 0 press Laser to switch on the laser loosen the button to switch off the laser If it s a non zero value press Laser and laser will shoot a certain time as set by the user PMOV SET Select this option and pressi 271 to enter the PMOV SET interface as below DISTANCE SET MM 000000 Press A or V to modify this value Press el to save the setting If this value is 0 press A V to move the laser head and loosen the button to stop the laser head If its a non zero value press E A V to move the laser head a certain distance as set by the user 14 PADO3 Operation LANGUAGE Select this option and press tel to enter the Language interface as below fai SFP XX HY
20. new version Q has been released Notice To observe the updating process it s recommended to use a Q USB flash disk with indicate light Notice 22 Download Document 7 2 Download Data 1 Copythefiles mol created by engraving amp cutting control software to the root directory of USB flash disk FAT16 format Electrify the MPC6515 Plug the USB flash disk into the MPC6515 If the indicate light D1 on the MPC6515 CPU keeps shining for seconds or minutes depend on the file size the controller is downloading processing file If D1 flashes swiftly download completes Remove the USB flash disk select and operate the processing file through the control panel having been selected and operated for the first time Q Downloaded configuration file can only be effective after Downloaded processing file can be operated directly Notice When you use the MPC6515 at the first time set up a Q configuration file according to the machanism parameters Then download the configuration file to MPC6515 and make it effective Same operation should be followed each time the narameter changes Q To observe the downloading process it s recommended to Notice use a USB sticker with indicator light The user can also lead the external USB indicator light signal to the panel of machine and use LED to show the working status of the Notice USB sticker Refer to Chapter 4
21. ription ss seo enea RO 24 CHAPTER 9 FAO iia 28 9 1 EXTERNAL INDICATOR LIGHT OF U DISK ieri eee 28 Fnctonal t soss st stit odo v S e e I E a A aR 28 aiia ola a BIRERE ON 28 9 2 CUSTOMIZE PAD03 CONTROL PANEL ccsseeecccccsssccecccsssseccccsesccccesssnsecesceaeeecs 28 FUNCUON AMY 22 22 A A A AL A E O 28 9 3 EXTERNAL INDICATOR LIGHT OF PROCESSING STATUS cccssseecccecssssececeeeecees 29 FUNCION nel ANO IO I i i i Au 29 Tariao eilo METEEN EE E EE U lu 29 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Od S ONA O E E AE OI AI o 29 FURIA R ra A o AE ii li ee a 29 A E EEE alal 29 O AGRADE ENGR VE DIE AAEE RSI a ARR 30 EUA MV a 30 IOSTUCUO a e O or dt AO 30 9 6 SOFTWARE LIMIT UNDER IMMEDIATE MODE eee 30 FUNCUONAlYiz A ai aa an in 30 ISLAN elia ciak a 30 9 7 CONTROL TWO LASER HEADS rn nn nn 30 FUNCUON AMY tt ariana leale 30 INSITUCHON e be Re e oh da o tO ih V ca 30 IV Preface Chapter 1 Preface Thank you for using Step Servo s Leetro motion controllers MPC6515 specially designed for laser engraving and cutting system This manual will instruct you on using MPC6515 in details Please read the instructions carefully before using MPC6515 User should debug the system with full consideration on protection measures to avoid any machine damage or human injury Warning Do not connect or use the Produ
22. rt MPC6515 if any error occurs to resume to the default status Refer to the above error codes descriptions to correct the error 27 MPC6515 Laser Engraving amp Cutting Controller User Manual V2 0 Chapter 9 FAQ 9 1 External Indicator Light of U Disk Functionality User can t see the indicator lights on MPC6515 installed inside a mahine During the process of data downloading user can observe the downloading process through the interface of PADO3 or through an external connected indicate light of the USB flash disk The external indicator light is used to lead the reading status signal of USB flash disk to the machine panel and show the status with LED Instruction Use Pin3 of Y1 on MPC6515 MC Indicate light signal of USB flash disk to drive the relay or LBD 9 2 Customize PADO3 Control Panel Functionality PADO3 is composed of control panel liquid crystal display and main board If you want to customize the panel please refer to the following interface description graph The control panel is connected to the main board through a 9pin header 28 FAQ KI Reserve f Reserve spk Reserve Reserve Reserve i Reserve i Reserve 7 Reserve lr ea Soo I Eee Start t User can design the panel according to the above diagram 9 3 External Indicator Light of Processing Status K9 connect to ground Functionality To confirm the processing status before operating the system a

MPC6515

Contents

Download Pdf Manuals

Related Search

Related Contents